Amulet Hotkey DXZC-AC zero client Quick Start Manual

QS-DXZC-AC01 DXZC-AC zero client Quick Start Guide The DXZC-AC is a PC-over-IP® (PCoIP®) zero client with an integral smart card reader. It is based on the TERA2 chipset and supports two heads of video at the desktop. The DXZC-AC has a single RJ45 network port . The DXZC-AMC has been evaluated by the CESG Commercial Product Assurance Scheme and approved for use at foundation grade for Remote Desktop v1.0. Smart card authentication The DXZC-AC integral card reader supports CAC and SIPRNet tokens, ISO 7816 and EMV 2000 Level 1, and is compatible with 5v, 3v and 1.8v smart cards. Important! Users must always insert smart cards into the DXZC-AC smart card reader with the integrated circuit chip (ICC) facing down. Before you start You must first configure a remote computer and PCoIP host, ready for connection to the DXZC-AC. The remote computer must be powered and connected to the appropriate network. You will need the IP address of the PCoIP host. Set up the DXZC-AC Using the diagrams below as a guide, connect the DXZC-AC as follows: 1. Connect at least one compatible monitor to the DXZC-AC, starting at Video 1 port. 2. Connect a keyboard and mouse to the front panel USB ports. 3. Connect audio devices, if required. 4. Connect the RJ45 network cable. 5. Connect the DXZC-AC PSU. Use only the PSU supplied with this DXZC-AC. 6. Power up the DXZC-AC, monitor and the remote workstation. POWER / MENU switch (Item 4 in Figure 1) A short button press turns on the unit. When the unit is on: ■ and in a PCoIP session, a short button press displays the On Screen Display (OSD) configuration menu; ■ and not in a PCoIP session, a short button press tries to establish a PCoIP connection; ■ a long button press turns off the unit. Available kits Part number DXZC-AC (one RJ45 socket) with IEC power lead and Power Supply Unit (PSU). KT-DXZC-3C02 Establish a PCoIP connection After setting up your DXZC-AC, you must establish a PCoIP session to connect the DXZC-AC to a remote PCoIP host or virtual desktop. The connection methods are summarized below. ■ Direct connections: To connect a DXZC-AC directly to a specific PCoIP host card, use the Direct to Host session connection type and provide the IP address (or DNS name) for the PCoIP host. Direct connections are not practical for very large PCoIP deployments. ■ SLP Discovery: If your DXZC-AC and PCoIP host reside on the same subnet, you can use the Direct to Host + SLP session connection type to discover available PCoIP hosts on the subnet. The OSD lists the first 10 hosts discovered. Choose the one you want to connect to. ■ Use a connection broker: A connection broker is a third party application that dynamically assigns DXZC-AC zero clients to remote workstations (or virtual desktops) based on the identity of the end-user. Use the Connection Management Interface session connection type on both the DXZC-AC and PCoIP host. You will need to provide the IP address (or DNS name) of the connection broker. 1 Insert smart card into reader with integrated circuit chip facing down. 2 Headset. 3 USB keyboard and mouse. 4 Power/Menu switch. 5 Device LED. 6 PCoIP LED. 7 Network connection to remote PCoIP host or virtual desktop. 8 Network status LEDs. 9 USB device. 10 Speakers. 11 DisplayPort connections to monitors. 12 PSU. DXZC-AMC 4 5 6 DXZC-AC front ü û 2 3 1 C DXZC-AC rear 9 7 10 12 11 8 Figure 1: Front and rear DXZC-AC connections and functions Continues on next page…

QS-DXZC-AC01 DXZC-AC zero client Quick Start Guide ©2017 Amulet Hotkey Ltd. All rights reserved. Information in this document is subject to change. No part of this document may be reproduced through any means including (but not limited to) electronic or mechanical, without express written permission from Amulet Hotkey Ltd. Amulet Hotkey Ltd may have patents, patent applications, trademarks or copyrights or other intellectual property rights covering subject matter in this document. PC-over-IP, PCoIP and the PCoIP logo are registered trademarks of Teradici Corp. Amulet Hotkey and ‘solutions you can bank on’ are registered trademarks of Amulet Hotkey Ltd. Other product names and company names listed within this document may be trademarks of their respective owners. Amulet Hotkey products are designed and built in the UK. Caution To reduce the risk of electric shock, make sure the unit is powered off before removing or installing components. Apart from those mentioned in this guide, there are no user serviceable parts inside. Warning ▪ To reduce the risk of fire or electric shock, do not expose this appliance to rain and moisture. ▪ Do not expose the appliance to dripping or splashing. ▪ Do not place objects filled with liquids on or near the appliance. Safety instructions 1. Install in accordance with these instructions. 2. Do not install near significant sources of heat. 3. Make sure the product is properly earthed. 4. Only use attachments and accessories approved by Amulet Hotkey. 5. Keep the product away from liquids. 6. Clean the product only with a dry cloth. Refer all servicing to qualified personnel. ■ Connecting the DXZC-AC to a virtual desktop: The DXZC-AC can use PCoIP to connect to a virtual desktop in a VMware® View™ environment. You must provide the IP address (or DNS name) of the View Connection Server. If you want users to log on manually, choose the View Connection Server session connection type. To set up automatic logons, choose the View Connection Server + Auto-Logon session connection type. Note: Use the On Screen Display (OSD), Administrative Web Interface (AWI) or PCoIP Management Console to establish a PCoIP connection. For full details about the connection methods, see the Session Connection Types section of the Teradici PCoIP® Zero Client and Host Administrator Guide, available on the Teradici Tech Support site: techsupport.teradici.com. Front panel indicators DEVICE LED (Item 5 in Figure 1) Shows the power status of the unit: ■ Red, in standby ■ Amber, in standby and can be woken by Wake-on-LAN or USB activity ■ Amber flashing, unit starting up ■ Green, unit is on and connected to the network ■ Green, flashing, unit is on but no network connection PCoIP LED (Item 6 in Figure 1) Shows the PCoIP session status: ■ Green, active PCoIP session ■ Green blinking, PCoIP link available but not in session Rear panel network indicators (Item 8 in Figure 1) Upper LED Indicates link activity: ▪ Off, no network connection ▪ Green constant, network ▪ Green flash, network traffic detected Lower LED Indicates connection speed: ▪ Off, no network connection (10 Mbit/s if upper LED is green) ▪ Amber, 100 Mbit/s connection ▪ Green, 1 Gbit/s connection More DXZC-AC documentation is available on the Amulet Hotkey website. Technical Support Europe: [email protected] N America: [email protected] Product documentation and downloads https://resources.amulethotkey.com/resources EMEA Sales +44 (0)20 7960 2400 [email protected] N America Sales +1 (212) 269 9300 [email protected] APJ Sales +61 409 930 884 [email protected] Defence and Security [email protected] Head Office Amulet Hotkey Ltd +44 (0)1626 837900 Cavalier Road, Heathfield Industrial Estate, Newton Abbot, Devon TQ12 6TQ, UK