AutoWatch 956 Owner's Manual

WORKMANSHIP AND MATERIAL FOR A PERIOD OF TWO YEARS. SHOULD THIS PRODUCT BE FOUND TO BE DEFECTIVE IN THE VEHICLE IN WHICH IT WAS ORIGINALLY INSTALLED, PFK ELECTRONICS SHALL REPAIR OR REPLACE THE PRODUCT OR ANY PART OF THE PRODUCT WHICH�PFK�ELECTRONICS AGREES�IS�DEFECTIVE�WITHOUT CHARGE. THIS�WARRANTY DOES NOT APPLY TO ANY PRODUCT WHICH HAS BEEN DAMAGED BY ACCIDENT, PHYSICAL OR ELECTRICAL ABUSE, IMPROPER INSTALLATION, ANY USE CONTRARY TO ITS INTENDED FUNCTION, UNAUTHORISED SERVICE (I.E. SERVICE BY ANYONE OTHER THAN PFK ELECTRONICS�OR�ITS AUTHORISED AGENTS/SERVICE�PERSONNEL),�FIRE,�FLOODING, INDEMNITY PFK ELECTRONICS (PTY) LIMITED AND KNIGHTWATCH (UK) LIMITED SHALL NOT BE RESPONSIBLE FOR ANY REMOVAL AND/OR INSTALLATION CHARGES, DAMAGE TO OR THE THEFT OF THE VEHICLE OR ITS CONTENTS, OR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES CAUSED BY ANY FAILURE OF THE PRODUCT TO FUNCTION PROPERLY. UNDER NO CIRCUMSTANCES SHOULD THIS WARRANTY, OR THE PRODUCT COVERED BY IT, BE�CONSTRUED AS AN�INSURANCE�POLICY AGAINST LOSS.��PFK�ELECTRONICS�NEITHER ASSUMES NOR AUTHORISES ANY PERSONS OR ORGANIZATION TO MAKE ANY WARRANTIES, NOR DOES IT ASSUME ANY LIABILITY IN CONNECTION WITH THE SAFE INSTALLATION, OR USE OF THIS PRODUCT. THIS IS THE COMPLETE PFK ELECTRONICS WARRANTY AND NO OTHER WARRANTY EXISTS.

This is the “Identity” number of your immobiliser. DO NOT LOSE IT - at the very least make sure you record the number as it can be used to disarm the immobiliser in the event of a malfunction. This number is also required when ordering additional Remotes. IMPORTANT�NOTICE FUNCTION BUTTON TRANSMIT BUTTON ACCESS�PIN BUTTONS The Auto Arming��Immobiliser Protection�to�your�vehicle�is�automatic. Switch�the�ignition�off. After 60 seconds the immobiliser automatically re-arms. Your vehicle is protected by anAutowatch immobiliser system designed to give years of trouble free operation, made with only the highest quality components and using state of the art technology you can be assured that your vehicle has the best electronic protection available. CONGRATULATIONS! Entering the Emergency Override number Refer to the 4 digit number attached to your keytag. Each number is entered individually using the ignition switch. As a comprehensive guide of how to enter the number, the following example shows how the override code number "2321" would be used. Should you enter a digit incorrectly, wait for at least 10 seconds and simply begin entering the number again, starting from the first digit of your code. Note that a "0" is entered by 10 on and off turns of the ignition. Allow�the�immobiliser�to Arm Turn�the�ignition�on�and�wait�10�seconds. Turn�the�ignition�on�and�off�twice.�(The�1st.�digit�of�your�override�code)�Wait�5�seconds. Turn�the�ignition�on�and�off�three�times.�(The�2nd.�digit�of�your�override�code)�Wait�5�seconds. Turn�the�ignition�on�and�off�twice.�(The�3rd.�digit�of�your�override�code)�Wait�5�seconds. Turn�the�ignition�on�and�off�once.�(The�last�digit�of�your�override�code)�Wait�5�seconds. You�now�have�approximately�60��seconds�to�start�the�vehicle. Disarming�the�Immobiliser Changing�the�4�digit�access�code Incorrect�code�entry�(Preventing�pin�search) The�led�on�the�remote�will�flash green�for�6�seconds. The�led�on�the�remote�will�flash green�for�6�seconds. The�remote�keypad�disables�for�5 minutes�to�prevent�further�code�input. The�LED�will��flash�red�every�2�seconds for�the�5�minute�duration. The�led�on�the�remote�will�flash green�for�6�seconds. The�led�on�the�remote�will illuminate�green The�led�extinguishes Enter�the�new�4�digit�access�code and�press�the�function�button Re-enter�the�new�4�digit�access code�and�press�the�function�button The�immobiliser�will�disarm. You�now�have�approximately�60��seconds�to�start�the�vehicle. If�you�do�not�switch�the�ignition�on�within�this�time,�the�immobiliser�will�arm�again. Enter the correct 4 digit access code on the remote. Enter�the�original�4�digit�access�code�on The�remote.�(Factory�default�is�1,2,3,4.) If an incorrectAccess code is entered 4 times consecutively. Press function button Within 6 seconds press the transmit button on the remote. 1 2 3 4 NB:�If�the�code�change�was�unsuccessful�the�unit�will�revert�to�the�original�code.