Eaton 415U-2 Installation Manual

installation guide Statutory requirements FCC: This device complies with Part 15.247 of the FCC Rules. Operation is subject to the following two conditions: • This device may not cause harmful interference. • This device must accept any interference received, including interference that may cause undesired operation. FCC: Unlicensed operation limits the radio power. High gain aerials may only be used to compensate for cable losses. � WARNING - EXPLOSION HAZARD Do not disconnect the device while the circuit is live unless the area is known to be non-hazardous. NOTE The 415U-2 module ships from the factory in configuration mode. The radio locale, frequency, and RF power need to be configured using the embedded web pages before use. Antenna installation Use Figure 1 as a guide for installing an antenna and attaching it to the module. Figure 1. Antenna installation Earth Stake For maximum range, install above local obstructions. Earth Conductor at least 5 AWG (16 mm2) * Wavelength: 360MHz = 32.7” (83cm) 512MHz = 22.8” (58cm) Weatherproof Connections (recommended: 3M™ 23 self- bonding tape) Mast Coaxial Cable GND at least 11 AWG (4 mm2) Stress Relief Loop Antenna* GND Surge Arrestor (recommended) 415U-2 Provide good ground connection to mast, module, and surge arrestor. If ground conditions are poor, use more than one stake. 1 Wavelength (minimum) Connecting to the module for confi guration The default settings for the 415U-2 are as follows: • IP Address: 192.168.0.1XX, where “XX” is the last two digits of the serial number shown on the printed label on the side of the module • Subnet Mask: 255.255.255.0 • Default Gateway: 192.168.0.1 • Username: user • Password: user 1. Connect a straight-through Ethernet cable between the module’s Ethernet port and a PC. 2. Open Internet Explorer on the PC. 3. Type “http://” followed by the IP address of the module and press Enter. Instruction Leafl et IL032043EN Effective April 2015

Cleveland, OH 44122 United States Eaton.com Eaton’s wireless business www.eaton.com/wireless Eaton is a registered trademark. All other trademarks are property of their respective owners. 415U-2 wireless mesh networking I/O and gateway installation guide © 2015 Eaton All Rights Reserved Printed in USA Publication No. IL032043EN April 2015 Instruction Leafl et IL032043EN Effective July 2015 NOTE All connections must be SELV <50 Vac and <120 Vdc. The following illustrations show the ports on the 415U 2. PWR RF 232 485 LED Indicator Lights I/O Connectors RJ-45 Ethernet Port (connects to hub or switch) USB Port RS-232 Port ETHERNET USB RS232 SUPPLY + - GND BAT SUP SUP + B A - + Power supply wiring The ground (GND) and “SUP –“ terminals are connected internally to the ground terminal. Connect the screw terminal on the end plate to ground for surge protection. Expanson I/O power and RS-485 serial connection An on-board RS-485 terminating resistor provides line attenuation for long runs. Place terminating resisters at each end of the RS-485 cable. Confi guration switches Use the DIP switches in the side access panel to select analog input voltage and current, external boot, and default configuration settings. DIP DESCRIPTION 1 AI3 current/voltage 2 AI3 current/voltage 3 AI4 current/voltage 4 AI4 current/voltage 5 Unused 6 Enables default configuration Input and output connections The digital input/output channels can be wired as inputs or outputs. Digital input Digital output Transistor Switch Device Voltage-free Contact TTL CMOS Output D1 D3 D4 D5 D6 D7 D8 GND +24V D2 DC Load + – D1 D3 D4 D5 D6 D7 D8 GND +24V D2 Differential current inputs (Al1, Al2) Single-ended current input (Al3, Al4) mA Loop-Powered Sensor Exernally Powered Sensor Power Supply D7 D8 GND +24V AI1 + AI1 _ AI2 + AI2 _ AI3 AI4 AO1 + AO2 + GND +24V mA Loop-Powered Sensor Power Supply Externally Powered Sensor DIP Switch Setting for Current IP GND +24V AI1 + AI1 _ AI2 + AI2 _ AI3 AI4 AO1 + AO2 + GND +24V 1 2 3 4 5 6 ON Analog output Single-ended voltage input AI PLC COM AI1 AI1 _ AI2 + AI2 _ AI3 AI4 AO1 + AO2 + GND +24V 0–25V Sensor 0–5 Vdc Sensor +24V AI1 + AI1 _ AI2 + AI2 _ AI3 AI4 AO1 + AO2 + GND +24V V V DIP Switch Setting for Voltage IP ON 1 2 3 4 5 6 ETHERNET USB RS232 B A - + 115S-xx 115S-xx RS-485 B A B A B A - + - + USB RS232 SUPPLY + - GND BAT SUP SUP + 15-30 Vdc Supply 3A Fuse Optional 10.8–15 Vdc Lead Acid Battery – + USB Host Factory Boot Switch ������������� Switches Side Access Panel