CEL-FI PRO Quick Start Manual

ging it and then plugging it back in. If the problem persists, return system for service replacement. Try resetting the Coverage Unit by unplugging it and then plugging it back in. If problem persists, return system for service. Network Unit is too close to a cellular tower. Move your Network Unit to another location. You might need to move your system to the other side of your home/ofce. Make sure that the vents (the small openings in the plastic housing) on the units are not blocked. Move the unit to a cooler area. The system will start working normally when it cools down. Make sure that the vents (the small openings in the plastic housing) on the units are not blocked. Move the unit to a cooler area. The system will start working normally when it cools down. Try moving the units farther apart. Try moving the units closer together. Please call your cell phone provider. Troubleshooting The key to better performance is the placement of the two units. (Error 7) Unit disabled by network The units are too far apart The units are too close together (Error 8) Input signal too strong (Error 4) NU is overheating (Error 3) CU is overheating (Error 6) NU Hardware Error (Error 1) Not receiving signal (Error 2) CU Hardware Error Relocate the Network Unit to another room or area where you have more coverage. (Use your cell phone to fnd the best cellular signal). CEL-FI PRO Quick Start Guide Box Contents: • Quick Start Guide • Network Unit • Coverage Unit • Power Adapters (2) • Mounting Brackets (2) FCC Requirements: This is a CONSUMER device. BEFORE USE, you MUST REGISTER THIS DEVICE with your wireless provider and have your provider’s consent. Most wireless providers consent to the use of signal boosters. Some providers may not consent to the use of this device on their network. If you are unsure, contact your provider. You MUST operate this device with approved antennas and cables as specifed by the manufacturer. Antennas MUST be installed at least 20 cm (8 inches) from any person. You MUST cease operating this device immediately if requested by the FCC or a licensed wireless service provider. WARNING. E911 location information may not be provided or may be inaccurate for calls served by using this device. When used with any mobile device utilizing the 1710-1755 MHz band, the FCC limits booster equipment placement to a maximum of 10 meters above ground level. Installation of this equipment which does not comply with federal requirements may subject the owner to FCC enforcement action. Changes or modifcations not expressly approved by Nextivity, Inc. could void the user’s authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment of and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help Copyright © 2014 by Nextivity, Inc, U.S. Patents pending. All rights reserved. The Nextivity and Cel-Fi logos are registered trademarks of Nextivity Inc. All other trademarks or registered trademarks listed belong to their respective owners. Designed by Nextivity in California. For more information, visit www.Cel-Fi.com. qsg-PRO-NA-English_14-0908

and are still seeking improved coverage, please visit the Troubleshooting on the reverse side of the Quick Start Guide. For more information and videos, please visit cel-fi.com. Find the best cellular signal. For Cel-Fi PRO to work correctly, use your phone to find the best 3G, 4G or LTE signal. Typically, you will get the best signal upstairs near a window. Step 1 Place the Coverage Unit (CU). Place the CU in the location where you need improved coverage. Step 3 Place the Network Unit (NU). Place the NU in the location where you get the best cellular signal. Step 2 Optimize Coverage. For best results, try moving the CU around to a few different spots. Typically, the farther the units are apart, the better coverage you will have. Although, it is possible to move the units too far apart. Step 4 Network Unit 2 Bars 3 Bars 5 bars! Too Far Cel-Fi Quick Start Guide Follow these simple steps for a quick and easy set-up. 3G/4G /LTE Network Unit Coverage Unit Too Close User Interface LCD Screen On/Off Button for LCD Backlighting Coverage Unit Coverage Unit Coverage Unit Coverage Unit Coverage Unit