JENCO 3173 Operation Manual

11.The instrument will display the conductivity value of the standard solution with the CELL K= flashing. If the CELL CONSTANT has been calibrated by using Step 9 & 10, please press the [MODE] key to exit calibration and return to normal operation. When you press the [ ∆ ] or [ ∇ ] keys, the unit will display K value with the CELL K= staying on. Using the [ ∆ ] and [ ∇ ] keys, you can now input the K value (from 70% to 130% of the probe basic cell constant). After release the [ ∆ ] or [ ∇ ] keys for 2 seconds , the unit will display the conductivity value with the C ...

parameter). PROBE BASIC CELL CONSTANT 6. The unit will display the actual (calibrated previously or default) cell constant while the lower part of the LCD will display the current selected cell number. Using the [ ∆ ] and [ ∇ ] keys, you can now change the probe basic cell constant to that you use from the 3 available cell constants (0.1, 1 and 10). 7. Press the [ENTER] key to save the new value of probe basic cell constant or press the [MODE] key to exit (and go to the next calibration parameter). CELL ...

If any damage is found, notify your Jenco representative immediately. All packing materials should be saved until satisfactory operation is confirmed. GENERAL INTRODUCTION The Jenco Model 3173/3173R Bench System is a microprocessor based instrument designed for use in field, laboratories and process control applications. Using a two-wire electrode cell, it is user-friendly for the precise measurements of conductivity, salinity, TDS (Total Dissolved Sol ...

INTRODUCTION The RS-232C interface feature can track all displayed values and interface your Jenco meter with recorders, printers, computers, etc. For example, the user can log all data simultaneously to an interfaced IBM PC/AT compatible computer. This section assumes you are familiar with the basics of data communication, the RS-232C interface, programming with computer languages, like Delphi, VB, VC, etc. A simple program must be written in order to send command and receive data from the unit. If you do not have that knowledge, you mus ...

Cell constant 0.1, 1.0, 10 ; user selectable Reference temperature From 15.0 to 25.0℃, default 25.0℃; user adjustable Temperature coefficient From 0.00 to 4.00%, default 1.91%; user adjustable K value From 70% to 130% of the probe basic cell constant TDS constant 0.5 (Fixed) LCD character size 21mm / 16mm high Calibration Back-up Yes Automatic temperature compensation Yes Audio Feedback All Touch Keys Communication RS-232C output (for 3173R only) Power Supply 6 AA batteries / AC adaptor (Output: DC 9V) Ambient temperature From 0 to 50 ℃ ...

research grade dried Potassium Chloride (KCl). Dissolve it in 1000ml of deionized water You can store the remaining solution in a plastic container for one week but the air space between the cap and the solution must be kept to an absolute minimum. The storage life can be prolong by storing the solution below 4°C. If you have any doubt of the accuracy of the stored solution, a fresh batch should be prepared. ...

parameter). PROBE BASIC CELL CONSTANT 6. The unit will display the actual (calibrated previously or default) cell constant while the lower part of the LCD will display the current selected cell number. Using the [ ∆ ] and [ ∇ ] keys, you can now change the probe basic cell constant to that you use from the 3 available cell constants (0.1, 1 and 10). 7. Press the [ENTER] key to save the new value of probe basic cell constant or press the [MODE] key to exit (and go to the next calibration parameter). CELL ...

11.The instrument will display the conductivity value of the standard solution with the CELL K= flashing. If the CELL CONSTANT has been calibrated by using Step 9 & 10, please press the [MODE] key to exit calibration and return to normal operation. When you press the [ ∆ ] or [ ∇ ] keys, the unit will display K value with the CELL K= staying on. Using the [ ∆ ] and [ ∇ ] keys, you can now input the K value (from 70% to 130% of the probe basic cell constant). After release the [ ∆ ] or [ ∇ ] keys for 2 seconds , the unit will display the conductivity value with the C ...