Corsair GRAPHITE 780T Installation Manual

Case Specifications 670mm 332mm 689mm Length .......................................................................................................689mm Width .........................................................................................................332mm Height ........................................................................................................670mm Weight ........................................................................................................11.3kg Maximum GPU Length Top Slots ...................................................355mm Maximum GPU Length All Slots .....................................................355mm Maximum CPU cooler height ..........................................................200mm Maximum PSU length .........................................................................260mm GRAPHITE SERIES® INSTALLATION GUIDE GRAPHITE SERIES 780T FULL-TOWER PC CASE 780T

Accessory Kit Contents Case Features x4 x16 x4 Long Fan Screws Short Fan Screws Cable Ties x10 x28 x1 Motherboard/HDD Screws SSD/ODD Screws Motherboard Standofs Side panels x6 120mm fan mount locations or x2 360mm radiators I/O panel with x2 USB 3.0, headphone, and microphone ports PSU and bottom fan mount dust filters x3 included AF140L 140mm fans x2 3.25" drive bays x6 HDD and SSD compatible drive trays Two ODD covers Tool-less drive cage x3 Tool-free SSD cages Top mesh panel Case feet A G B H C I D J E K L F a b c d f e B B L F G C D E K E D A A J H I

1. Removing the Side Panels 2. Install the Motherboard 3. Install the PSU 4. Install PCI-E/PCI Card(s) Simply pull upward on the side panel latches to release. Note: Corsair recommends removing both side panels and setting them aside when building your system to avoid accidental damage. Both side panels are interchangeable and should be removed to reduce clutter. First, install your motherboard’s I/O shield (see your motherboard’s manual for guidance). Then, align your motherboard with the pre-installed standofs, and use the provided screws to secure the motherboard to the motherboard tray. Position the PSU on the bottom of the case then align the case holes and secure the PSU with the screws provided with your power supply. First, remove thumbscrews and corresponding slot cover(s). Then, install the add-on card and secure with thumbscrews.

5. Install 5.25" drive/device (ODD) 6. Install 2.5" SSD First, remove the front panel 5.25" drive bay cover then slide the ODD into the drive bay until the tool-free latch clicks, securing the drive. Note: To release an optical drive, push in the tool-free tab then pull the drive outward. Pull down the tab and place the SSD into the tool-free expandable SSD cage until you feel it secure. Note: To remove the SSD from the cage, simply pull the tab down to release. 7. Power the Case Fans 8. Connect the Front I/O Connectors See your motherboard’s manual for front panel header locations and pin-outs. USB 3.0 USB 2.0 HD AUDIO POWER SW RESET SW HDD LED POWER LED + POWER LED - 1 2 3 1. Connect the SATA power connector to the PSU SATA power cable. 2. Connect the 3 or 4-Pin fan connecter to the case fan header. 3. Push the fan speed selector button on your case to toggle fan speed.

Frequently Asked Questions 1. How do I remove the I/O Panel ? A. First, remove the front fascia by pushing in the three tabs from inside the fascia, then push towards the front of the case. B. Next, unscrew the 2 screws at each side of the panel. 2. Does the polarity matter with the I/O panel’s power and reset header? No, only the LED headers. 3. Who should I contact if I received my case damaged or one of the fans is no longer working? Please go to corsair.force.com and request an RMA so that we can replace the damaged part(s). 4. Where can I mount a fan? Fan Mount Locations Front 3 x 120 mm or 2 x 140 mm Top 3 x 120 mm or 2 x 140 mm Rear 1 x 120 mm or 1 x 140 mm Bottom 2 x 120 mm Side X Mid X 5. How do I remove the front panel? To remove the front panel, push the top corners of the plastic cover. 6. How do I remove the bottom dust filter(s)? To remove the bottom dust filter, first locate the pull out tab underneath the PSU, then pull the bottom dust filter out. 7. How do I remove the Drive Cage? Locate and remove the two screws securing the cage to the base on the bottom of the case then pull the drive cage out. Drive cages are stackable and can be installed on top of each other, or completely removed for improved cooling. Note: Note: The HDD cage can also be removed by removing the four screws located directly under the base on the bottom of the case.