Larson Electronics DVR-ALG-4CH Quick Setup Manual

5 1 9 7 3 11 6 2 10 8 4 12 DVR-ALG Series 16CH back panel Item Description 1 VIDEO IN BNC connectors for camera video channels in. Number of channels is dependent on the model of the DVR. 2 Monitor Out (CVBS) BNC connector for CVBS video monitor. 3 AUDIO IN RCA connector for audio in cable. 4 ON / OFF switch 5 USB 6 HDMI Connector HDMI monitor cable. 7 VGA Connector VGA monitor cable. 8 AUDIO OUT RCA connector for audio out cable. 9 LAN RJ-45 connector for Ethernet drop cable. 10 RS-485 terminations Connector for RS-485 devices. Connect the D+ and D- terminals to T+ and T- of PTZ receiver respectively. 11 12 Vdc Plug for 12 Vdc power adapter. 12 GND terminal Ground terminal post. Mouse control A standard 3-button (left / right / scroll-wheel) USB mouse can also be used with this DVR. To use a USB mouse: 1. Plug the USB mouse into the either the front panel or back panel USB connector of the DVR. 2. The mouse will be automatically detected. If the mouse is not detected, the mouse may not be compatible with the DVR. Please refer to the recommended device list from your provider. This guide provides instructions to initially setup the DVR-ALG series digital video recorder (DVR) for AHD, HD-TVI, 960H analog and IP cameras. DVR Front Panel USB Interface IR Receiver Power LED Status TX / RX DVR-ALG Series front panel Item Usage Power LED Indicator turns green when DVR is powered up. Status STATUS indicator lights in red when HDD is reading / writing. TX / RX LED indicator blinks green when network connection is functioning properly. IR Receiver Sensor for the remote control. USB Interface DVR Back Panels 5 1 9 7 3 11 6 2 10 8 4 12 DVR-ALG Series 4CH back panel DVR-ALG Series 4/8/16-Channel AHD, HD-TVI, 960H Analog and IP Camera Recorder Quick Setup Guide 1 of 4 www.larsonelectronics.com Larson Electronics, LLC

are accessible and the ventilation holes on the sides are not blocked. 2. Connect the ground terminal on the back of the DVR to an earth ground. Refer to local codes for proper grounding. Step 3. Install a monitor, mouse, power For the following steps, refer to the back panel photo above for the location of connectors. 1. Install and setup your monitor in accordance with the instructions provided with the monitor. Do not power it on at this time. 2. Cable the HDMI or VGA connector to your monitor’s VGA or HDMI input. The HDMI interface provides the best performance. 3. Plug the mouse into the USB connector on the front or back of the DVR. 4. your local area network (LAN) into the RJ45 LAN connector on the back of the DVR. 5. Connect the power cord to the power connector on the back panel of the DVR, and then into a UPS (recommended) or surge protector. Step 4. Install cameras Install your security cameras. Always follow the installation instructions provided with the camera. Step 5. Connecting it together – initial system setup 1. Plug the coaxial cables from the cameras into the BNC camera input connectors on the back of the DVR. 2. Power on your cameras. 3. 4. Power on the monitor. NOTE display the input connected to your DVR (HDMI or VGA). Step 6. Using the Wizard for basic c uration setup Power on the DVR. Normally, an Alibi logo splash screen appears within 2 minutes. Action Left click Single click: Live view: Select channel and show the quick set menu. Menu: Select and enter. Double click: Live view: Switch between single-screen and multi-screen. Click and drag: PTZ control: pan, tilt and zoom. Tamper-proof, privacy mask and motion detection: Select target area. Digital zoom-in: Drag and select target area. Live view: Drag channel / time bar Right click Live view: Show menu. Menu: Exit current menu to upper level menu. Scroll wheel Scroll up: Live view: Previous screen. Menu: Previous item. Scroll down: Live view: Next screen. Menu: Next item. Installing the System Step 1. Getting Started: Unpacking the Equipment What’s in the box Your system includes: • DVR-ALGSeries DVR • USB mouse • HDMI cable • Power adapter for DVR • This Quick Start Guide your supplier for a replacement. Verify that your order is complete. What you need • Cameras and cables compatible with the DVR. The Video Input ports on the back panel support most analog CCTV camera brands and Alibi HD-TVI, AHD, and 960H analog cameras. • IP cameras installed on the Ethernet network (LAN) that associate with the DVR must be Alibi IP cameras. • Tools to install the cameras and route power, video and audio cables • Fasteners to attach the cameras to the mounting surfaces • VGA or HDMI compatible computer monitor to connect to the DVR. (An HDMI cable is provided.) • Uninterruptible power supply (UPS) is recommended. This device is used to ensure system stability during voltage surges, sags, and outages. If a UPS is not available, a power strip with strong surge protection is highly recommended. Step 2. Install the DVR For the following steps, refer to the back panel photo above for the location of connectors. 2 of 4 www.larsonelectronics.com Larson Electronics, LLC

settings), a login window will open. In the Login window, select a User Name with administrative privileges, enter its password, then click OK. A window of Menu icons will open. Model DVR-ALG-4CH DVR-ALG-8CH DVR-ALG-16CH Video compression H.264 Video input 4-ch 8-ch 16-ch BNC interface (1.0 Vp-p, 75 Ω), supporting coaxitron connection Supported HDTVI input 1080p / 25Hz, 1080p / 30Hz, 720p / 25Hz, 720p / 30Hz, 720P / 50Hz, 720p / 60Hz Supported AHD input 720p / 25Hz, 720p / 30Hz CVBS input Support IP video input 1-ch, up to 2.0 MP resolution 2-ch, up to 2.0 MP resolution Audio compression G.711u Audio input 1-ch, RCA (2.0 Vp-p, 1 KΩ) CVBS output Support HDMI / VGA output 1-ch, 1920 × 1080 / 60 Hz, 1280 × 1024 / 60 Hz, 1280 × 720 / 60Hz, 1 024 × 768 / 60 Hz 1-ch, 4K (3840 × 2160) / 30Hz, 2K (2560 × 1440) / 60Hz, 1920 × 1080 / 60 Hz, 1280 × 1024 / 60 Hz, 1280 × 720 / 60Hz, 1024 × 768 / 60 Hz Encoding resolution When 1080p Lite mode is not enabled: 1080p (non-real-time) / 720p / VGA / 960H / 4CIF / CIF; When 1080p Lite mode enabled: 1080p lite / 720p lite / VGA / 960H / 4CIF / CIF Frame rate Main stream: 1/16 fps to real time frame rate Sub-stream: 960H / 4CIF@12fps / 2CIF (non-real-time); CIF / QVGA / QCIF (real time) Video bit rate 32 Kbps to 6 Mbps Audio output 1-ch, RCA (Linear, 1 KΩ) Audio bit rate 64 Kbps Dual-stream Support Stream type Video, Video and Audio By default, the Setup Wizard will open automatically. Important Notes for using the Wizard: • Password Strong” administrator user password. Follow the on-screen NOTE: There is no factory default password for this device. • Date and Time • Storage - HDD with it in this window. If you installed an HDD or replaced the HDD, that HDD needs to be initialized by the recorder before it can be used to record data. Select (check the box for) that HDD, then click Init to initialize the disk. NOTE: Init will erase all data from the disk and can take several minutes to complete. When the initialization is complete, click Next to continue. • Network Settings: By default, the recorder acquires it’s network settings using DHCP (dynamic network settings). Depending on the un-check the enable DHCP option in the network setup menu, and then click apply. Step 7. Access the Menu system functionality of the system. To use most menus, the user must log into the NVR system, either locally or remotely, with administrative privileges. To open the Menu system from the Live View screen, right click anywhere in the screen, then select Menu. 3 of 4 www.larsonelectronics.com Larson Electronics, LLC

mouse. The device will not accept a keyboard; you will use an on-screen keyboard to enter information. 2. Power up the NVR if it is not already running. 3. Right-click anywhere on the screen to bring up an initial menu. Select Menu from this list. You will then get a dialog box asking for a username and password. 4. Double-click in the lower left corner of this dialog box (not the lower left corner of the screen). There is an invisible button in this dialog box. Another dialog box will appear, asking for the unit’s serial number and a secure code. A unique serial number will populate on its own. 5. Call Larson Electronics tech support at 800-369-6671. When a support tech answers, tell them that you have lost the administrative password to your NVR and wish to reset it to factory default. They will ask for the unit’s serial number, which you got in step 4. Please provide a return contact number with the serial number. The tech will have to validate the serial number and call back with a confirmation number. They will provide you with the secure code. Write this code down before entering it into the dialog box on screen to make sure that you got it correctly from the tech. Click OK when done. 6. After entering the secure code and clicking OK, you will then be able to set the admin password to one of your choosing. Note: As a security feature, be aware that the secure code that the tech provides will only be good for 24 hours. Model DVR-ALG-4CH DVR-ALG-8CH DVR-ALG-16CH Synchronous playback 4-ch 8-ch 16-ch Remote connections 128 Network protocols TCP / IP, PPPoE, DHCP, EZVIZ Cloud P2P, DNS, DDNS, NTP, SADP, NFS, iSCSI, UPnP™, HTTPS, ONVIF SATA 1 SATA interface (1 HDD max) 2 SATA interfaces (2 HDDs max) HDD Capacity Up to 8TB capacity per HDD Two-way audio input 1-ch, RCA (2.0 Vp-p, 1 KΩ) (using the audio input) Network interface 1 × RJ45 10M / 100M self-adaptive Ethernet interface 1 × RJ45 10M / 100M / 1000M self-adaptive Ethernet interface USB interface 2 × USB 2.0 1 × USB 2.0 on the front panel 1 × USB 3.0 on the back panel Serial interface 1 × RS-485 serial interface, half-duplex Power supply 12 Vdc Consumption (without HDD) ≤ 15 W ≤ 20 W ≤ 30 W Working temperature 14 ºF to 131 ºF (-10 ºC to +55 ºC) Working humidity 10% to 90% Dimensions (W × D × H) 12.4 × 9.5 × 1.8 in (315 × 242 × 45 mm) 15.0 × 12.6 × 1.9 in (380 × 320 × 48 mm) Weight (without HDD) ≤ 2 kg (4.4 lb) ≤ 2 kg (4.4 lb) ≤ 2 kg (4.4 lb) 4 of 4 www.larsonelectronics.com Larson Electronics, LLC