InMotion inTC Series Quick Start Manual

Before operating this product, please read this quick-start guide to ensure proper use. Please store these instructions a safe place for future reference. FEATURES • Compact Design • High Sensitivity sensor • 800TVL Resolution • 0.01 Lux • Wide Dynamic Range • HLC, BLC, DEFOG • Dual Optical Vari-Focal • Sens Up • Optional UTC Programmer • 12VDC or 24VAC PRECAUTIONS 1. Before installing and operating the unit, please read this manual carefully. 2. Precision components are contained in this camera, please avoid violent vibrations during installation and maintenance. Do not connect the power until you have completed the installation. 3. Please obey all local electrical wiring regulations when using this unit. 4. Do not use abrasive or corrosive materials for cleaning. Use only a soft cloth for cleaning. 5. To prevent damage to the lens or sensor, do not point the camera directly into the sun or very strong light sources. 6. Do not use the camera outside it’s working temperature (-10°C~ 50°C / 14°F ~122°F) or humidity (<90%) ranges. 7. Ensure that the power supply meets the current requirements of the camera and that the supply voltage is inside the tolerances of the camera: 24VAC ±10% 8. Ensure that the fixings used are adequate to support the load of camera. 9. In case of camera failure, do not attempt to dismantle or service the camera yourself. Please refer to qualified service personnel for repair of the camera. CONNECTIONS Connections for video and power are made to the flying lead from at the rear of the camera. Two connectors are provided: 1. Video output connector, 75Ω BNC socket. Connect a male BNC connector to a Monitor, DVR or UTC programmer to this socket. 2. Power Input connector. This is a 2.1mm DC jack. Connect 24VAC or 12VDC. Observe polarity of 12VDC connections. The centre conductor is +12VDC ±10% and outer is ground. Refer to the adjacent diagram for clarification. OSD ACCESS The camera is supplied in a general configuration that will suit the majority of installation requirements. Should advanced configuration be required, the optional UTC (up the coax) Programmer may be connected to the camera to access the camera On Screen Display (OSD) for user programming. MENU Exposure.. Day/Night.. WhiteBalance.. Display Adjust.. Connect the Video-In connector of the UTC controller to the Video-Out connector of the camera. Connect the Video-Out of the UTC controller to a display monitor. To activate the camera OSD, depress the joystick button on the UTC Controller (operation is confirmed when LED is latched on). Push the joystick to select a menu from the list. Push the joystick  to change the selected value. Press the joystick button to call the sub-menu or execute a command. To return from a sub-menu to the previous menu, select “Return” and press the joystick button. OSD MAIN MENU When the OSD menu is launched, you are presented with the adjacent opening screen. A menu option followed by a  indicates the presence of a sub-menu. Options set to OFF will not show a  until set to ON Use RETURN  to return to the previous menu. LENS menu: • MODE - DC or manual selection Indoor -Default, set to fixed values OUTDOOR- Iris and shutter will auto adjust to lighting situation. • LENS- Used to optimize iris level using damping load. EXPOSURE menu: • SHUTTER - Auto, Manual, FLK selection, 1/60~1/50K. (1/50~50K PAL) Set this on to reduce the exposure time of each image. This can be used to reduce blur in images with fast changing content. FLK mode; Use this when flicker is observed in the image under fluorescent lighting. When WDR is ON, the shutter menu is disabled. • AGC- Off or Level Control -Used to adjust overall gain. • SENS UP - Slows frame rate and increases low light sensitivity. • BRIGHTNESS - Sets the level of the overall brightness • D-WDR - Actively controls gamma compensation to provide optimal image exposure in images with extremes of lighting. When WDR is ON the D-WDR menu is disabled. • DEFOG- Improves the clarity of image obscured by fog by analysing the brightness of the image and compensates the color of the image. • BACKLIGHT - BLC or HLC Adjust the area to be enhanced and sets the level for BLC. HLC is the ability to reverse bright points to black or gray, (areas such as headlights, any high luminance areas) this function will improve the overall picture. When WDR is ON the backlight menu is disabled. WDR WDR - On,Off • GAIN - Low, Middle, High - Sets level of WDR . • WDR OFFSET - Used to improve contrast in bright/dark areas. Rev 0.1 MAIN MENU LENS DC EXPOSURE.  WDR OFF WHITE BAL ATW DAY&NIGHT AUTO NR  SPECIAL  ADJUST  VIDEO OUT NORMAL RESET EXIT SAVE EXPOSURE SHUTTER AUTO AGC ON  SENS-UP AUTO  BRIGHTNESS 40 D-WDR OFF DEFOG OFF BACKLIGHT OFF RETURN RET LENS LENS MODE INDOOR LENS ADJUST RETURN RET EXPOSURE MENU WDR GAIN MIDDLE WDR OFFSET RETURN RET 12VDC GND

WHITE BAL - ATW (default) • ATW - the camera automatically samples the image for optimum white balance. • AWC-SET - Allows the white balance to be set automatically and locked. This option is normally used when no white reference is present in the image. To set the white balance, hold a white object in front of the camera, with light from the source falling on it and press the joystick to set and lock the white balance. • INDOOR -Used for color temperature between 2,300K and 9500K. • OUTDOOR- Used for color temperature 1,800 and 10,500k. • MANUAL - this option allows the Red and Blue gain to be manually set in the image. Note, using this option requires care to ensure all cameras on one system have the same color response. • AWB- Used to adjust white balance for a specific controlled scene. DAY&NIGHT DAY/NIGHT - AUTO, COLOR, B/W, EXTERNAL • AUTO - Allows the camera to switch from color to B/W mode in low light. The switching thresholds and hysteresis time are adjustable. • COLOR - fixes the camera in color mode • B/W - fixes the camera in monochrome mode. • Extern - NA NOISE REDUCTION NR - OFF, ON • 2 DNR- Level control • 3 DNR - Function is used to improve the picture quality by filtering the noise which is generated under low light conditions . SPECIAL - OFF, ON - Press to open submenu. • CAM TITLE - OFF, ON turning on enables sub menu to enter up to 15 characters for a camera title. • D-EFFECT- Freeze- On, Off - Mirror- Off, Mirror, V-Flip, Rotate D-Zoom- Zoom, Pan & Tilt Motion D-Zoom-Zoom, Pan & Tilt   triggered by motion in image. Neg image- DIS- Digital image Stabilization. • MOTION - OFF,ON, Select area, sensitivity, view • PRIVACY - OFF, ON, Select area • LANGUAGE - 16 Languages • DEFECT - Dead Pixil Compensation • UTC CONTROL -Ver 1, Ver 2, Ver 3, Ver 4 • RS485- NA • VERSION- Displays version of camera firmware. NOTE: When WDR is on and Wide is selected for video out the following functions are disabled; Freeze,D-Zoom, Motion D-Zoom and DIS. When WDR is off and wide is selected for video out DIS is disabled. Note: For UTC control Ver.3 is for the inUTC Controller and Ver. 4 is for the inUTC-ZF Controller DISPLAY ADJ - OFF, ON - Press to open submenu. • SHARPNESS - Level control. • MONITOR - CRT, LCD • LSC - Compensates for shading effect when lens is at very wide angle. VIDEO OUT- Wide, Normal • WIDE - The camera produces a field of view based on the focal lenght of the attached lens. • NORMAL - The field of view narrows by approximatly 40% over the focal length of the attached lens. [Exp 2.8~12mm will show as 3.9~16.8mm} RESET - Press to open submenu • FACTORY - Reset to defaults. System PAL NTSC Imaging Sensor Advanced Mega Pixel Sensor Effective Pixels 1305x1049 PAL Performance Resolution 800TVL Sensitivity 0.01Lux Wide Dynamic Range 130dB Max S/N Ratio 52dB Day / Night Software Controlled Lens Type Fixed 3mm Optical Dual Vari-Focal 4.2mm Mount 12mm Functions OSD 15 Languages Shutter 1/50~1/120,000 1/60~120,000 Flickerless On/Off Wide Dynamic Range On/Off Low/Medium/High D-WDR Off/Low/Medium/High DEFOG Auto/Manual/Low/Medium/High Digital Image Stabilize Yes AGC Adjustable Level SENS UP Adjustable Level 512x Electronic shutter Off/On 1/200,000 sec maximum Sync Internal Camera ID Number Off/On 1~255 Camera Name Off/On, 15 Characters White Balance ATW/Push/Manual 2D DNR Off,On 3D DNR Off/Level Gamma 0.35,0 .4, 0.45, 0.5, 0.55 Motion Detection 4 areas, Off/On, Position & Sensitivity Privacy masking 8 areas, Off/On, Color, Position Image functions Sharpness, Mirror, Defog, HLC, BLC, Negative, Shade Comp Input/Output Video Output CVBS 1.0Vp-p 75Ω - BNC Programming interface Optional UTC Controller Power 12VDC or 24VAC +/-10% 4.2W max Physical Construction Extruded / Metal Color Black Dimensions 4.5””H x 8.5” W x 2.094””D Weight 1.2lbs Mounting Base with angle adjustments Environmental Operating Temperature -10°C~+50°C Humidity Less than 90%, non condensing Order Codes FDIC Camera inTCFS2N2D30 NCUA Camera inTCNS2N2D30 Blank Camera inTCBS2N2D30 MOTION D-ZOOM SELECT AREA 1 DISPLAY ON SENSITIVITY [ 3] PIP OFF D-ZOOM (-X2) DELAY TIME [ 10] STAY TIME [ 5] WAIT TIME [ 30 DEFAULT  RETURN RET 2D & 3D NR 2 DNR ON 3 DNR ON  RETURN RET SPECIAL CAM TITLE OFF D-EFFECT  MOTION OFF PRIVACY OFF LANGUAGE ENG  DEFECT  UTC CONTROL VER 1 RS485 NA VERSION 130716 RETURN  SPECIFICATIONS DAY/NIGHT Auto  COLOR  B/W  EXTERNAL NA RETURN  WHITE BAL ATW ATW AWC-SET INDOOR [ 96] OUTDOOR- MANUAL AWB RETURN  ADUST SHARPNESS [ 3] MONITOR LCD  LSC OFF RETURN  SPECIAL CONTINUED VIDEO OUT RESET FACTORY RESET  RETURN RET SPECIAL ADJUST inMotion CCTV 519 Bennet Lane Suite 100 Lewisville, Texas 75057 214-960-4640 Please visit our website for full information: www.inMotioncctv.com inMotion reserves the right to amend specifications and design without prior notice RESET