HID iCLASS RK40 Installation Manual

An ASSA ABLOY Group company ASSA ABLOY _____________________________________________________________________________________________________ HID Corporation 9292 Jeronimo Road Irvine, CA 92618-1905 USA TEL (949) 598-1600 (800) 237-7769 FAX (949) 598-1690 Web page - www.hidcorp.com e-mail – [email protected] iClass Keypad Reader Install Manual 6094-901 Rev A Page 1 of 2 PARTS INCLUDED SPECIFICATIONS • 1 - iCLASS Keypad Reader • Voltage Range: 12VDC (10 - 16VDC). • 1 - Installation Manual • Current: 100mA avg / 220mA peak. • 2 - 3.5mm x .6 pitch x 12mm Phillips machine screws • Cable distance to Host: 500ft (152m) max – Wiegand. • 3 - #6-32 x .375” Phillips self-tapping machine screws 50ft (15m) max – RS-232. • 2 - #6 x 1.5” Phillips sheet metal screws 4000ft (1216m) max – RS-485. • 1 - #6-32 x .375” Spanner security screw • Op. Temperature: -31°F - +149°F (-35°C – +65°C) Recommended: • Open collector output: Sink – 40mA, source – 1mA. • Up to 10 wire splices * Standards: • Cable, 9 conductor, 22AWG, shielded (Wiegand) • Cable , 6 conductor, 22AWG, shielded (Serial) • Read/Write* capability in ISO 1SO 15693-2 mode with HID iCLASS credentials. • Linear DC Power Supply • Metal or plastic junction box • Security Tool (for security screw) HID 04-0001-03 • Read/Write* capability in ISO 1SO 14443-B mode with HID iCLASS 16KS. • Magnetic Tamper switch - Ademco 945T, Sentrol 1038T, GRI 100T or 110T or Aleph DC-2531 • Read capability of CSN/UID in ISO 1SO 14443-A1 mode with HID Mifare and other 3rd party Mifare credentials. * RK40 available with 18” wire pigtail or 10-pos. removable screw terminal connector. RWK400 includes 8-pos. and 10- pos. removable screw terminal connectors. * RK40 is a read only, while RWK400 is a read/write unit. INSTALLATION 1- Disassemble A. Remove the screw at the bottom of the unit. B. Lift the mounting plate out at the bottom side C. Slide mounting plate down 2- Install Tamper Switch An internal magnet provides tamper indication when used with a magnetic reed switch connected to an external alarm system. Locate Switch behind the left side of the mounting plate, centered between the mounting holes. Electrical Back Box Wall Surface

An ASSA ABLOY Group company ASSA ABLOY _____________________________________________________________________________________________________ HID Corporation 9292 Jeronimo Road Irvine, CA 92618-1905 USA TEL (949) 598-1600 (800) 237-7769 FAX (949) 598-1690 Web page - www.hidcorp.com e-mail – [email protected] iClass Keypad Reader Install Manual 6094-901 Rev A Page 2 of 2 3- Install Mounting Plate Attach the mounting plate onto the back box or a wall surface. Dimensions are in inches (centimeters). OPTIONAL SPACER MOUNTING PLATE 0.156 / 0.40 cm 1.650 / 4.19 cm 2.000 / 5.08 cm 3.280 / 8.33 cm 0.220 / 0.56 cm 0.300 / 0.76 cm 1.650 / 4.19 cm 2.000 / 5.08 cm 0.175 / 0.44 cm 0.110 / 0.28 cm 0.355 / 0.90 cm 1.550 / 3.94 cm 1.550 / 3.94 cm 1.130 / 2.87 cm 0.080 / 0.20 cm 1.000 / 2.54 cm 4.490 / 11.40 cm 4- Connecting Serial Port (Model RWK400 Only) Wiegand Port (Models RK40, RWK400) 8 Pin Terminal Function 10 Pin Terminal Color-coded Pigtail Function 1 Ground 10 Violet Open Collector 1 2 Y / RS-232 TX 9 Blue Hold 1 3 Z 8 Yellow Speaker 1 4 Ground 7 Drain Shield Ground 2 5 RS485B / RS-232 RX 6 Brown Red LED 1 6 RS-485A 5 Orange Green LED 1 7 Ground 4 White Data 1 8 DC+ 3 Green Data 0 2 Black Ground 1 Red +DC (10-16 VDC) 3 1 Optional Connections 2 Drain wire can be used for data return line when a separate power supply is used. 3 +DC, Return & Drain wires are common between the Wiegand and Serial Ports. 4 In RS-485 mode, pin 2 must be connected to pin 6 and pin 3 must connected to pin 5 with jumpers at the connector. 5- Testing A. Turn Power On – Watch the sign-on LED and hear the speaker tone sequences. B. Read Card – Present a valid card to the reader and verify the visual and audio feedbacks. 6- Mounting Reverse the procedure in step 1 to attach the unit to the mounting plate. Optional Features FCC WARNING: This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. For proper regulatory compliance, the drain wire should be disconnected at the power supply end of the cable. The reader is intended to be powered from a limited power source output of a previously certified power supply. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. RS232/485 interface/Host Mode - for applications requiring a serial link. See Protocol Document 6090-902 for information Open Collector Output – controls an external device (13.8VDC Max). See iCLASS Application Note for details Configuration Options - Configure LED, Speaker, and other features. See How To Order Guide or iCLASS Application Note for details Hold Input – when asserted, this line either buffers a card read or disables a card read until released, as configured.