Gigabyte MB10-DS Series Quick Reference Manual

12 10 11 15 14 13 16 19 18 17 22 21 20 23 26 25 24 28 27 29 31 30 32 33 34 35 36 Front Panel Header/ 前面板 HDD Back Plane Board Header/ 硬盤背板排針 ATX Power/ 电源 PMBUS Memory Population Configuration/ 安装内存 Type Ranks PerDIMM and Data Width 1600, 1866, 2133, 2400* 1600, 1866, 2133, 2400* 1600, 1866, 2133, 2400* 1600, 1866, 2133, 2400* 1600, 1866, 2133, 2400* 1600, 1866, 2133, 2400* 1600, 1866, 2133, 2400* 1600, 1866, 2133, 2400* 1600, 1866, 2133, 2400* 1600, 1866, 2133, 2400* 1600, 1866, 2133, 2400* 1600, 1866, 2133, 2400* Speed (MT/s); Slot Per Channel (SPC) and DIMM Per Channel (DPC) 1 Slot Per Channel 1DPC 2 Slot Per Channel 1DPC 2DPC RDIMM RDIMM RDIMM RDIMM SRx4 ECC SRx8 ECC DRx8 ECC DRx4 ECC Rear I/O Connector/ 后面板接口 SATA Connector/SATA 接口 No. Pin Define 1 GND 2 TXP 3 TXN 4 GND No. Pin Define 5 RXN 6 RXP 7 GND 7 SATA SGPIO Header/ 串行 GPIO 5 1 NVME Connector 4 1 No. Pin Define 1 GND 2 SMBUS Data 3 SMBUS Clock 4 GND 1 2 13 14 TPM Connector/ 可信平台模块 BMC F/W Readiness LED State Description On BMC firmware is initial Blink BMC firmware is ready Off AC loss BMC Firmware Readiness LED (LED_BMC1): CPU/System FAN/ 风扇 1 4 1 4 IPMB Serial Port Cable Connector/ 串行端口 2 1 10 9 No. Pin Define 1 NDCD- 2 NSIN 3 NSOUT 4 NDTR- 5 GND 6 NDSR- 7 NRTS- 8 NCTS- 9 NRI- 10 No Pin  仅Intel Xeon® D-1541处理器支持DDR4-MHz内存。  只使用一个DIMM时，必须安装到内存插槽0。  若安装顺序有误，系统将不能正常引导。 Jumper Settings/ 跳线设置 1 5 2 3 4 No. Desription 1 Clear CMOS Jumper 1-2 Close: Normal operation (Default setting) 2-3 Close: Clear CMOS data. 2 ME Update Jumper 1-2 Close: ME update. 2-3 Close: Normal operation (Default setting) 3 ME Recovery Jumper 1-2 Close: Normal operation. (Default setting) 2-3 Close: ME recovery mode. 4 S3 Power On Select Jumper 1-2 Close: Stop an initial power on when BMC is not ready. 2-3 Close: Keep initial power on. (Default setting) 5 SATA Port 0 DOM Support Jumper Jumper 1-2 Close: Enable SATA port DOM support funtion. 2-3 Close: Normal Operation. (Default setting) If a SATA type hard drive is connected to the motherboard, please ensure the jumper is closed and set to 2-3 pins (Default setting), in order to reduce any risk of hard disk damage. 1 2 Definition P5V GND 3 NC Pin No. 1 2 3 4 7 8 6 5 No. Pin Define 1 CLK 2 P_3V3_AUX 3 LPC_RST 4 P3V3 5 LPC_LAD0 6 IRQ_SERIAL 7 LPC_LAD1 8 No Connect 9 LPC_LAD2 10 No Connect 11 LPC_LAD3 12 GND 13 LPC_FRAME_N 14 GND No. Pin Define 1 SDIN 2 GND 3 SDOUT MB10-DS Series Quick Reference Guide/ 快速测试参考指南 1 5 1 3 1 8 4 5 1 24 1 1 2 23 1 2 25 26 No. Pin Define 1 3.3V 2 3.3V 3 GND 4 +5V 5 GND 6 +5V 7 GND 8 Power Good 9 5VSB 10 +12V 11 +12V 12 3.3V No. Pin Define 1 GND 2 GND 3 GND 4 GND No. Pin Define 1 PMBus Clock 2 PMBus Data 3 PMBus Alert 4 GND 5 3.3V Sense No. Pin Define 1 Clock 2 GND 3 Data No. Code Description 1 CPU Intel Xeon® processor D-1541, FCBGA1667 SoC (MB10-DS0/3) Intel Xeon® processor D-1521, FCBGA1667 SoC (MB10-DS1/4) Intel Xeon® processor D-1581, FCBGA1667 SoC (MB10-DS2/5) 2 SFP+1_2 SFP+ LAN connectors#1/#2 3 LAN1_2 LAN ports 4 USB3_MLAN BMC Management LAN port (top) / USB 3.0 ports (bottom) 5 CPU0_FAN CPU fan connector 6 VGA VGA port 7 SW_ID ID switch button w/LED 8 SW_PWR Power button w/LED 9 LED_STA System Status LED 10 P12V_AUX2 8 pin power connector 11 FP_1 Front panel header 12 ATX1 24 pin main power connector 13 DIMM_P0_A0 Channel 1 slot 0 14 DIMM_P0_A1 Channel 2 slot 1 15 DIMM_P0_B0 Channel 3 slot 0 16 DIMM_P0_B1 Channel 4 slot 1 17 BAT1 Battery 18 PMBUS PMBus connector 19 SATA_DOM0 SATA port 0 DOM support jumper No. Pin Define 1 Power LED+ 3 No Pin 5 Power LED- 7 HDD LED+ 9 HDD LED- 11 Power Button 13 GND 15 Reset Button+ 17 GND 19 ID Switch+ 21 ID Switch- 23 NMI Switch- No. Desription 1 System Status LED 2 Power button w/LED 3 ID switch button w/LED 4 VGA port 5 USB 3.0 ports 6 KVM Server Management 10/100/1000 LAN Port (Dedicated LAN Port) 7 LAN ports 8 SFP+ LAN ports (MB10-DS3/MB10-DS4/MB10-DS5)  Note: DDR4 2400MHz is only available on Intel Xeon® D-1541 processor.  When only one DIMM is used, it must be populated in memory slot0 first.  System will not boot normally with incorrect populated sequence. Off State Description Yellow On 1Gbps data arte Green On 100Mbps data arte 10Mbps data arte 10/100/1000 LAN LED: Speed LED Link/Activity LED Speed LED Link/Activity LED Speed LED Link/Activity LED Speed LED Link/Activity LED Speed LED Link/Activity LED 13 12 24 No. Code Description 20 SATA0 SATA 3 6Gb/s connector 21 SATA1 SATA 3 6Gb/s connector 22 SATA_2_3 SATA 3 6Gb/s connectors 23 SATA_4_5 SATA 3 6Gb/s connectors 24 SATA_SGPIO SATA SGPIO header 25 SYS_FAN 2 System fan connector#2 26 COM1 Serial port cable connector 27 LED_BMC1 BMC firmware readiness LED 28 BP_1 HDD back plane board header 29 NVME_PH NVME connector 30 TPM TPM module connector 31 IPMB IPMB connector 32 CLR_CMOS Clear CMOS jumper 33 PCIE_1 PCI Express x16 slot 34 ME_UPDATE ME update jumper 35 ME_RCVR ME recovry jumper 36 S3_MASK S3 Power On Select jumper Power button/LED: Green On Off Description System is powered on System is powered off State System Status LED: Green On Amber On Off Description Normal operation Critical alert. System is not ready State No. Pin Define 13 3.3V 14 -12V 15 GND 16 PS_ON 17 GND 18 GND 19 GND 20 -5V 21 +5V 22 +5V 23 +5V 24 GND No. Pin Define 5 +12V 6 +12V 7 +12V 8 +12V No. Pin Define 2 5V Standby 4 ID LED+ 6 ID LED- 8 System Status LED+ 10 System Status LED- 12 LAN1 Active LED+ 14 LAN1 Link LED- 16 SMBus Data 18 SMBus Clock 20 Case Open 22 LAN2 Active LED 24 LAN2 Link LED- No. Pin Define 1 BP_SGP_CLK 3 BP_SGP_GLD 5 BP_SGP_DOUT 7 Key Pin 9 GND 11 BP_LED_G_N 13 BP_SGP_DIN 15 GND 17 GND 19 P_3V3_AUX 21 P_3V3_AUX 23 GND 25 BP_PRESENSE No. Pin Define 2 No Connect 4 FAN_SGP_GLD 6 GND 8 Reset 10 BP_LED_A_N 12 GND 14 No Connect 16 SMB_BP_DATA 18 SMB_BP_CLK 20 BMC_ACK 22 BMC_REQ 24 Key Pin 26 GND No. Pin Define 1 GND 2 +12V 3 Sense 4 Speed Control ID switch button w/LED: Blue On Off Description Unit selected for identification No identification State 12QM1-MB10D0-00R No. Pin Define 4 SLOAD 5 SCLK Speed LED Link/Activity LED State Description Yellow On 1Gbps data rate Green On 10 Gbps data rate SFP+ LAN LED: