RCA RDR4320 Quick Start Manual

B4323LI Li-Ion Battery (2550 mAh) CH4301 Desktop Rapid Charger PS4301 Power Supply BC4300 Belt Clip Antenna ANH4300V - VHF MIC RDR4320 Handheld Radio RDR4380 Handheld Radio RDR4350 Handheld Radio What’s Included: Attaching the Battery: Removing the Battery: Attaching audio accessory / programming cable: Attaching the Antenna: Attaching the Belt Clip: 1. While laying flat, put the battery into the radio as shown, horizontally push to the top along the aluminum slot. 2. As shown, up the battery latch forward until a click is heard. 1. As shown, hold the radio like this. 2. As shown, push up the battery latch with another hand. 3. Slide the battery as arrow direction shown. 1. Rotate the screws counter- clockwise to remove them. 2. Align the screw holes on the belt clip with those on the radio’s body, and then tighten the screws clockwise. Note: To remove the belt clip, loosen the screws. 1. Open the accessory jack cover. As shown, align the plug with the accessory jack, then connet it. 2. As shown, tighten the screw clockwise on the plug. Note: To remove accessories, loosen the screw counter- clockwise. 1. Turn the antenna clockwise to attach it. Note: To remove the antenna, rotate it counter-clockwise. 3 3 2 2 2 2 2 2 1 1 1 1 1 1 1 P1 Key (hot key) 2 PTT Key (transmit key) 3 P2 Key (hot key) 4 Emergency Call Key 5 Antenna 6 LED Indicator 7 Channel Knob 8 Radio On-Off/ Volume Knob 9 Earpiece (RDR4350/RDR4380 only) 10 Simplex Microphone (RDR4350/ RDR4380 only) 11 LCD Display (RDR4350/RDR4380 only) 12 Function Keypad (RDR4350/RDR4380 only) 13 Speaker 14 Numeric Keypad (RDR4350/RDR4380 only) 15 Duplex Microphone (RDR4350/ RDR4380 only) 16 Battery Latch 17 Accessory Jack Cover 18 Strap hole 19 Belt Clip 20 Battery 21 Battery Pole Piece 22 Accessory Jack 23 Micro SD Encryption Card Cover Prodcut Overview 5 1 2 3 4 16 17 18 19 20 21 22 23 6 7 8 9 10 11 12 13 13 14 15 RDR4320 RDR4350 RDR4380 Programmable Keys [P1] key, [P2] key, four direction keys, key, can be set as function or menu shortcut keys by your RCA dealer. The default state of [P1] and [P2] shortcuts are for high-low power switching. You only need to press the corresponding shortcut key to quickly access the needed menu or function. Function/Enter key Receive/Call key Back/Option key Hangup key Direction key Function Keypad (RDR4350 / RDR4380 models)

LED Indication Charging Status LED Flashes Red Slowly Standby (no load) LED Glows Red Charging LED Glows Orange 85% Charged LED Glows Green Fully Charged LED Flashes Red Rapidly Error STATUS INDICATION IN RADIO (RDR4350 / RDR4380 models) LCD Icon Icon Name Icon Radio Status Battery Strength Icons Low battery power More bars indicate more battery power RSSI No Signal More bars indicate better signal strength Message Icons New message/unread message Inbox is full Operation Mode Icons TMO mode DMO mode Analog mode Power Icons Transmit with lower power Transmit with middle power Transmit with high power Profiles Icon Silent mode Ring Vibrate Custom Audio Accessories Audio accessory has been connected Call Status Icon On the phone Group Selection Icon Select talk group Encryption Icon Encryption ON Radio LED indicator LED Indication Radio Status LED Glows Red Transmitting the call LED Glows Green Receiving the call LED Glows Red On Both Sides Phone Call LED Flashes Red Slowly Low Battery Power LED Flashes Green Slowly Channel is Idle LED Glows Orange Channel is Busy Battery indicator Battery Usage Status Indicator Light Status Power > 40% Battery indicator light shut down 10% < Power < 40% Green light flash Power < 10% Red light flash No Power LED indicator light and battery indicator light shut down Basic Operations Turning on/off radio Rotate the Radio On-Off/Volume knob clockwise / counter-clockwise until a click is heard to turn on/off the radio. Adjust the volume After turning the radio on, rotate the Radio On-Off/Volume knob clockwise to increase the volume or counter-clockwise to decrease the volume. Selecting a channel According the series number on the Channel Knob to rotate and select the desired channel. While rotating the knob, there is an automated channel number Voice prompt. Mode Switch Through Channel Selector knob. Each channel of the radio can be set as analog channel or digital channel by dealer. The user can set up through CPS software. Call Group Call Talk group can be set by dealer in advance the operation methods are the same under DMO mode and TMO mode. • Transmitting a group call 1. Select the desired talk group through Channel Knob. 2. Hold down [PTT] key to transmitt a group call. • Receiving and replying a group call You can receive the group call without any key operation. If reply is needed, please hold down [PTT] key after the speech of the other side and then speak to microphone. Care and Cleaning To guarantee optimal performance as well as a long service life of your radio, please follow the tips below. Radio Care Keep the radio far away from substances that can corrode the electronic circuit. Do not hold the radio by its antenna or headset cable directly to prevent damage to its normal use. Attach the accessory jack cover whtn the radio is not in use. Radio Cleaning Clean up the dust and fine particles on the radio surface and charging piece with a clean and dry lint-free cloth or a brush regularly. Use neutral cleanser and a non-woven fabric to clean the keys, control knobs and front case after long-time use. Do not use chemical preparations such as stain removers, alcohol, sprays or oil preparations, so as to avoid surface case damage. Make sure that the radio is completely dry before use. NOTE; Turn off the radio and remove tha battery before cleaning. Charging the Battery Charging Operation Steps Use only the charger and battery specified by RCA Communications Systems. Charger LED can indicate the changing progress. 1. As shown, Connect the power adapter to AC power socket and the jack at the back of the charger. 2. As shown, insert battery or radio with battery in the charger, and make sure there is good contact between battery and charging terminals. 3. The charging process starts when LED glows red. 4. LED glows green to indicate that charging is complete. NOTE: The standard 2250mAh battery charging normally takes about 4 hours, for optimal battery performance. Initial charging for new battery should take up to 5 hours. 2 1 2 1

2. Bluetooth device search and clear operation interface, as shown in Figure1.2.1. Description： The interface has three options "Searching", "Clear All", "Voice Device"; Click "Searching" to find the Bluetooth device； Click "Clear All" to clear the previous Bluetooth pairing information; "clear information" option will clear the  Bluetooth  module's  existing  pairing  information.  It  is  recommended  to  use  this  option  if  multiple connections  are  unsuccessful,  and  then  pair  again,  or  clear  the  message  and  connect  again  when connecting a new device. If "Voice Device" appears, the Bluetooth device is found but it is not connected. If a device is successfully connected ,as shown in Figure 1.2.3 Figure1.2.3

In    Select  "Find  Device"Can  enter  the  ,  Enter  the  search  interface,  the module will enter the search mode, If any device is found, it will be displayed below, as shown in Figure 1.3.2 The following figure shows that the device has been discovered and is being connected, as shown in Figure 1.3.3. Figure 1.3.3                                                                                Figure 1.3.4 The following figure shows that the connection is successful, as shown in Figure 1.3.4 4. NOTE: (1)One‐on‐one operation is required for pairing. Do not open multiple terminals and Bluetooth devices for pairing at the same time. (2)Each time you re‐pair the connected device, please select "Clear All", clear the original pairing information of the module, and then search for the device to perform pairing connection. (3)Please use the supporting Bluetooth headset provided by the terminal manufacturer to avoid inconvenience to your normal use. Thank you!

two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE 1: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. NOTE 2: Any changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

To control your exposure and ensure compliance with the occupational/controlled environment exposure limits always adhere to the following procedures. Guidelines: • Do not remove the RF Exposure Label from the device. • User awareness instructions should accompany device when transferred to other users. • Do not use this device if the operational requirements described herein are not met. Operating Instructions: • Transmit no more than the rated duty factor of 50% of the time. To transmit (talk), push the Push-To-Talk (PTT) button. To receive calls, release the PTT button. Transmitting 50 % of the time, or less, is important because this radio generates measurable RF energy exposure only when transmitting (in terms of measuring for standards compliance). • Hold the radio in a vertical position in front of face with the microphone (and the other parts of the radio, including the antenna) at least one inch (2.5 cm) away from the nose. Keeping the radio at the proper distance is important because RF exposures decrease with distance from the antenna. Antenna should be kept away from eyes. • When worn on the body, always place the radio in a RCA’s approved clip approved body-worn accessories is important because the use of RCA’s or other manufacturer’s ries may result in exposure levels, which exceed the FCC’s occupational/ led environment RF exposure limits. for this product. Using non-approved accesso control