Topeak Alien DX Operation & User’s Manual

The ultimate tool for road and mountain biking ALiEN ™ User's Guide GB ! WARNING Using Pedal Wrench ! WARNING ! WARNING The ALiEN™ DX Tool is equipped with a mini pedal wrench for emergency use. The mini pedal wrench is for emergency use only. The mini pedal wrench's strength is limited. Never attempt to remove securely attached pedals from crank using the mini pedal wrench. Insert 8mm Allen key into 8mm hex on mini pedal wrench. Unfold tools as shown for additional leverage. Remove mini pedal wrench from B section Tighten disc brake rotor bolts with the T25 Torx bit. 1 Congratulations on your purchase of a Topeak ALiEN series tool. It's the first two-piece mini tool designed for both road and mountain cyclists. The ALiEN series tools fold neatly for easy carrying. Each tool is designed for maximum durability and strength for years of use. This guide will instruct you in the proper use of your ALiEN series tool. Please read all instructions and warnings carefully before using the ALiEN series tool. •ALiEN™DX 2 1. Flip open safety lock. 2. Hold flat tool section in one hand while depressing the locking button with your thumb. 3. Slide Allen tool apart. 4. Reverse above procedure for reassembly. •ALiEN™RX and ALiEN™XS To separate, press tab and slide section A as shown. The knife blades on the ALiEN series tools are sharp. Be careful when using the knife blade. Use extreme caution when opening and closing your ALiEN series tool. The locking device is used both to lock tools in place for use and to keep tools from deploying when stored. For additional safety, the locking device is used for knife blade storage. The A section contains a very sharp knife blade. Be careful when using the knife blade. Make sure the knife blade is locked securely in the open position when used. Failure to lock knife blade during use can result in serious injury. Be careful when storing knife blade. Make sure all fingers are clear of blade path. Be sure knife blade is locked closed during storage to prevent accidental deployment. Separating the ALiEN™ series tool Using Locking Device on A section Using the T25 Torx Bit 4 mm Allen Key Locking Device These two tools are combined. Slide down the 8mm Allen head to use the 5mm Allen key. Slide up to use the 8mm Allen key. Using the 5mm and 8mm Allen Keys B section A section Tab ALiEN ™ XS 17 tools ALiEN ™ DX 27 tools ALiEN ™ RX 16 tools

Mount clip bag on seat post Release Button 4mm Allen Key Rubber Pad Mount clip bag on stem 5mm Allen Key Logo facing forward Remove stem cap. Facing forward Copyright © Topeak, Inc. Printed in Taiwan / 2006 Use Primary Chain Link Fence to install or remove chain pin. Use Secondary Chain Link Fence to loosen stiff links. Primary Chain Link Fence Secondary Chain Link Fence 5 mm Allen key Chain Pin Tool: available in ALiEN II & Mini 18. Press chain pin as little as necessary to loosen the stiff link. Using Chain Tool Install new chain pin or remove old chain pin. When pressing in the chain pin, push down on the top of the chain to keep it fully engaged in the chain link fence. Make sure the press pin of the chain tool is centered against the chain pin. ! WARNING NOTE: OPTIONAL PARTS (sold separately) F55 Art no. TC1008 Art no. TMS-SP21 F66 F55 F66 Using Tire Levers on ALiEN™DX M-TT01-GB 4/06 Using Chain Tool on ALiEN™ XS The folding resistance of the A section and the B section can be adjusted by using the 4mm Allen key, screwdriver, or #1 philips. Adjusting folding resistance with 4mm Allen key. Tool maintenance Adjusting folding resistance with #1 Phillips. Adjusting folding resistance with screwdriver Warranty Claim Requirements To obtain warranty service, you must have your original sales receipt. Items returned without a sales receipt will assume that the warranty begins on the date of manufacture. All warranties will be void if The ALiEN is damaged due to user abuse, system alteration, modification, or used in any way not intended as described in this user's guide. NOTE: ALiEN™DX 8mm open end wrench should be used for disc brake bleed nuts only. Lubricate ALiEN tools with teflon based lubricant when needed. 2-year Warranty: All mechanical components against manufacturer defects only. LIMITED WARRANTY Topeak products are available only from professional bicycle shops. Please contact your nearest Topeak authorized bicycle dealer for any questions. For customers in the USA, call: 1-800-250-3068 Website: www.topeak.com The specifications and design are subject to change without notice. * • The A section serves as the handle for the chain tool. • The chain tool is inserted into the 8mm box wrench located on the A section. • The chain tool may be inserted at different angles to the box wrench for better chain access. • The 5mm Allen key located on the B section is used to operate the chain tool. A section B section • A single tire lever is located on the plastic body of both A and B sections. • To access tire lever on the A section, unfold all tools, except knife blade, to their open and locked position. • To access tire lever on the B section, unfold all tools.