Toa DM-524B Instruction Manual

Please carefully follow the instructions in this manual to ensure long, trouble-free use of your equipment. 1. SAFETY PRECAUTIONS •�Before installation or use, be sure to carefully read all the instructions in this section for correct and safe operation. •�Be�sure�to�follow�all�the�precautionary�instructions�in� this section, which contain important warnings and/ or cautions regarding safety. •�After�reading,�keep�this�manual�handy�for�future�reference. When Installing the Unit •� (When�attached�to�the�ST-73A)�Avoid�installing�or� mounting the unit in unstable locations, such as on a rickety table or a slanted surface. Doing so may result in the unit falling down and causing personal injury and/or property damage. •� Do� not� lay� the� connection� cable� where� it� can� be� walked�on�or�tripped�over,�causing�personal�injury. Indicates a potentially hazardous situation which, if mishandled, could result in moderate or minor personal injury, and/or property damage. CAUTION Model No. YM-121 Type Flexible shaft Input Connector XLR-3-11C�or�equivalent Output Connector ø21,�3-pin�plug�(BTS21P3B) Finish Gold, sparkling paint Size 367�mm�(length) Weight 295 g Model No. DM-524B DM-524S Type Moving�coil�microphone Polar Pattern Cardioid pattern Rated Impedance 600�Ω,�balanced Rated�Sensitivity –54.5�dB�(1�kHz,�0�dB�=�1�V/Pa) Frequency Range 100�Hz�to�10�kHz Output Connector ø21,�3-pin�plug�(BTS21P3B) Switching�circuit Short-off�type Finish Microphone body, gooseneck shaft: Gold, sparkling paint Size ø40�x�532�mm (length) ø40�x�557�mm (length) Weight 465�g 475�g Accessories ø21,�3-pin�receptacle�(BTS21R3A) ... 1 Machine�screw�M3�x�10� ..............�3 Plain�washer�(for�M3) ...................�3 Spring�washer�(for�M3)� ................�3 Nut�(for�M3)� .................................�3 Note The� design� and� specifications� are� subject� to� change� without�notice�for�improvement.� 4. SPECIFICATIONS 3. FEATURES 2. HANDLING PRECAUTIONS •� When�using�the�DM-524B�or�DM-524S,�do�not�grasp�the� head of microphone or microphone element section in order�to�avoid�acoustic�feedback. •� Avoid�installing�the�unit�in�humid�or�dusty�locations,�in� locations exposed to the direct sunlight, near the heaters, or in locations generating sooty smoke or steam as doing otherwise may result in unit failure. •� Take�care�not�to�drop�the�unit�onto�the�floor�nor�bump�it� against a hard object as the unit could fail. •� To� clean,� be� sure� to� first� disconnect� the� connection� cable,�then�wipe�with�a�dry�cloth.�When�the�unit�gets�very� dirty,� use�a�cloth�damped�in� a�neutral� cleanser.�Never� use benzene, thinner, alcohol, or chemically-treated cleaning�cloth�because�such�volatile�liquids�could�deform� or discolor the unit. •� (When� attached� to� the� ST-73A)� Do� not� pick� up� the� microphone stand by the microphone, as this could lead to failure. [DM-524B, DM-524S] [YM-121] [ST-73A] (Option) •� The�Dynamic�Microphones�DM-524B�and�DM-524S�are� characterized to eliminate handling noise as minimum. •� Use� of� an� optional� ST-73A� Microphone� Stand� allows� the�DM-524B,�DM-524S,�or�YM-121�to�be�placed�on�a� speech desk or table in a conference room. • Optional product Microphone�stand:�ST-73A

BTS21P3B Receptacle BTS21R3A ø41 3-ø3.2 Countersink ø33 120° Shield 26 ø25 154 557 Plug BTS21P3B Chassis ground ø40 [DM-524S] *�0�dB�=�1�V 50 100 200 500 1 k 2 k 5 k 10 k -30 -20 -10 0 10 20 (dB*) (Hz) 5. DIMENSIONAL AND CIRCUIT DIAGRAMS 6. FREqUENCY RESPONSE (DM-524b, DM-524S) URL:��http://www.toa.jp/ 133-04-00007-00 Unit�:�mm The symbol mark above is not applied to YM-121.