Rogers yale Installation Manual

Package Contents 1. Quick Start Guide 2. Installation Instructions 3. Door Marker 4. Touchpad (Outside Escutcheon) 5. Latch (Inside Escutcheon) 6. Inside Mounting Plate 7. Battery Cover 8. 4 AA Alkaline Batteries 9. Deadbolt 10. Strike Plate 11. Screw Pack › 2 Through Bolts › 4 Bolt & Strike Mounting Screws › 3 Latch Mounting Screws 12. Keys Tools Required: 1. #2 Phillips screwdriver 2. Flathead screwdriver

Door Lock Compatibility Check Note: Do not remove any elements from the door except door lock deadbolt. 1. Door should have two holes one for deadbolt and one for the handle. Mortise doors and all in one handle locks are not compatible. 2. Ensure there is enough clearance space above and below bore holes so that installation of lock is not obstructed. Look for chain locks, glass windows or any other possible obstruction within 2" above and below bore holes and 1" on either side.

3. Check door thickness. Standard door sizes between 1 3/4" to 2 1/4" are fully compatible. Doors inbetween 1 3/8" to 1 1/4" require use of thin door gasket on the inside components. 4. Check for proper alignment of door by ensuring door unlock and locks smoothly with existing set-up. Compatibility Summary:

Preparing Door Lock for Installation The lock is packed representative of how it will install on the door. Before installing the lock on the door: 1. Inside Latch Side › Loosen the screw (Phillips #2) holding the battery cover. › Slide the battery cover up and out (note the two tabs at bottom of battery cover). (Fig. 1A). › Remove the inside mounting plate (with gasket) from back (door side) of the inside latch (Fig. 1B).

2. Inside Mounting Plate Ensure that gasket on inside Mounting Plate is properly fitted. Note the positioning of the gasket's five rubber nubs (Fig. 2). 3. Outside Touchscreen Side (with gasket) Remains assembled (Fig. 3).

There are two latch options: 1. When inserting the deadbolt into the door make sure it is inserted with the up arrow pointed upwards. 2. Install deadbolt in door. Note: the deadbolt must be in a retracted (unlocked) position when installing the lockset. For the standard Yale deadbolt, secure bolt to door with two (2) M4 x 25.4mm [8-32 x 1"] screws supplied. 3. Install strike on the door frame, making sure to allow for the bolt to be centred in the strike. Secure strike to frame with two (2) M4 x 25.4mm [8-32 x 1"] screws supplied. Choosing Latch Type › For doors with a pre-existing notch for the faceplate, the standard Yale deadbolt can be used. › For doors with only the deadbolt bore hole, use the drive-in latch.

1. Install Outside Touchscreen side of the lock first (Fig. 1A). Route wire harness through bore hole under bolt (Fig. 1B). Ensure tongue slides through black deadbolt hole (Fig. 1B arrow pointed). Note: Wire harness goes under bolt (Fig. 1B). Installation 2. Holding the Outside Touchscreen side of the lock flush to the door, position the inside mounting plate by first routing the wire harness through the mounting plate's 1/2" hole (Fig. 2) then inserting mounting plate "Tongue" into groove at the bottom of the touchscreen part of the lock.

3. Secure both assemblies using (2) M6 x 59.5mm pan head machine screws (Fig. 3), making sure that outside of the lock is vertically aligned. Do not over tighten. 4. Attach cable assembly connector to the inside part of the lock PC board by lining up notches on top of cable connector to slots on PCB connector (Fig. 4). Connector should be pressed in firmly until completely seated.

5. Using care position and bend cable to ensure that the cable lies against the back recessed area of the latch side of the lock. Hook the cable under the cable hook (Note: label on circuit board) to prevent binding when installing the latch side of the lock over the mounting plate (Fig. 5). 6. Install the Inside Latch side of the lock on the inside mounting plate. Note: the horizontal orientation of the tailpiece as you insert the latch side; the latch should be vertical (Fig. 6).

7. Install and secure using (3) M4 x 8mm [8-32 x 5/16"] pan head screws through the latch part of the lock into the mounting plate. Important: Before installing the batteries, test the mechanical operation of the lock by operating the latch. The movement of the bolt should be smooth and unobstructed. Note: The bolt must be in a retracted (unlocked) position prior to installing the batteries. 8. Insert four (4) AA alkaline batteries. Install battery cover and tighten Phillips head screw. Upon powering. The lock will flash and beep several times and respond with the vocal prompt: "Welcome to Yale Real Living." Note: Open Door before initial activation of Door Lock. Activate Door Lock to adjust for proper handling.

Installation Checklist