Universal Remote Control Easy Clicker UR3L-SR4 Operating Manual

STEP2 Press a [MACRO] button and the [OK/SEL] button simultaneously for 3 seconds. The CBL device LED will turn on for 30 seconds. The next step must be performed while the LED is on. STEP3 Press the [CH5] button to erase the functions stored in the button. The CBL device LED will blink twice to confirm that the memory button has been erased. L. Programming Volume Control L. Programming Volume Control Volume and Mute control are factory- programmed to automatically transfer to the respective Device mode you select, as follows: CBL : TV TV : TV DVD : TV If you wish to store the Cable volume control in CBL mode, use the following steps. STEP1 Press the [OK/SEL] button and [CBL] button simultaneously for three seconds. The device LED will turn on for 30 seconds. The next step must be performed while the LED is on. STEP2 Press the [VOL5] button. The device LED will blink. STEP3 Press [CBL] button. The device LED will blink twice to confirm the programming. Note : To return CBL device to TV volume repeat steps above replacing [CBL] with [TV] in Step 3. M. M. Programming Channel Control Programming Channel Control Channel controls are factory-programmed to automatically transfer to the respective Device mode you select, as follows: The device LED will blink twice to confirm that the code has been stored. G. G. The Learning Method The Learning Method STEP1 Press the [Device] button (CBL, TV or DVD) to be programmed and the [INPUT] buttons simultaneously for 3 seconds until the Device LED light turns on. STEP2 Line up the UR3L-SR4 to the other remote, head-to-head, 1 or 2 inches apart. STEP3 Press any button on the UR3L- SR4 that you want to teach a command to. For example, if you want to teach the [MUTE] button, press the [MUTE] button. STEP4 Press and hold the [MUTE] button on the other remote until the UR3L-SR4 Device LED light blinks twice. *Note : The LED will blink 5 times if there was an error in the learning process. In so, repeat STEPS 3 and 4. Continue learning other buttons by repeating STEPS 3 and 4. STEP5 Once you have completed teaching UR3L-SR4 all desired commands for that Device, save the learned commands by pressing the [Device] and [INPUT] buttons simultane- ously until the Device LED blinks 3 times. Now test all the buttons to make sure they learned correctly. H. H. Erasing a Single Learned Erasing a Single Learned Command Command STEP1 Press the [Device] and [INPUT] buttons simultaneously for 3 seconds until the Device LED light turns on. STEP2 Press and hold the button you code. If any of the functions do not operate as they should, repeat the instructions from STEP 3 above to continue the Auto Search Method. STEP4 Press the same [DEVICE] button to store the code. The Device LED will blink twice to confirm that the code has been stored. E. E. To find the Three-Digit Code To find the Three-Digit Code that Was Programmed using that Was Programmed using the Auto Search Method the Auto Search Method STEP1 Press the appropriate [DEVICE] button and the [OK/SEL] button simultaneously for three seconds. The device LED will turn on for 30 seconds. The next step must be performed while the LED is on. STEP2 Press the [INFO] button. The device LED will blink a number of times indicating the number of each digit for the code. Each digit is separated by a one second interval of the LED being off. Example :One blink, then three blinks, then eight blinks indicates the code number 138. *Note : Ten blinks indicates the number 0. F. F. Programming a Second Programming a Second TV to the DVD Button TV to the DVD Button STEP1 Press the [DVD] button and the [OK/SEL] button simultane- ously for 3 seconds. The DVD LED will turn on for 30 seconds. The next step must be performed while the LED is on. STEP2 Press the [TV] button. STEP3 Point the remote control toward the TV and enter the three-digit code for your TV from the TV codes table. STEP4 Store the three-digit code by pressing the [DVD] button. STEP2 Press and hold the [DEVICE] key for 5 seconds until the Device LED will blink once and stays on. Continue to hold the [DEVICE] key and press the number key assigned to your brand in the Quick Set- up Code Table and release both [DEVICE] key and the number key to save the code. The Device LED will blink twice to confirm that the code is stored. STEP3 Point the remote control at the component. STEP4 Press the power button. If it turns off, it is programmed for your component. If it does not turn off, use the Pre- Programmed 3-Digit code Method or Scanning Method. Repeat the steps above for all compo- nents. (CBL, TV, DVD). B. B. Quick Set-up Code Tables Quick Set-up Code Tables C. C. Manual Programming Manual Programming The remote control can be programmed by entering a three-digit code number that corresponds to particular brands and models of equipment. The three- digit code numbers are listed in the code tables sections of this instruction manual. STEP1 Turn on the equipment that you want the remote control to operate (Cable Box, TV or DVD) . STEP2 Press the [DEVICE] button and the [OK/SEL] button simultane- ously for three seconds. The corresponding device LED will turn on indicating that it is ready to be programmed. The LED will remain on for 30 seconds. The next step must be entered while the LED is on. STEP3 Point the remote control toward the equipment and enter the three-digit code number assigned to your brand from the code tables. If there are more than one three-digit number listed for your brand, try one code number at a time until your equipment turns off. *Note: You can verify that you have selected the correct code by pressing the [POWER] button. The equipment should turn back on. Then try all of the functions on the remote con- want to erase for 3 seconds. The Device LED will blink twice to confirm the erasure. STEP3 To exit, press and hold both the [Device] and [INPUT] buttons simultaneously until the Device LED blinks 3 times. I. I. Erasing All Learned Commands Erasing All Learned Commands from One Device from One Device STEP1 Press the [DEVICE] and [INPUT] buttons simultane- ously for 3 seconds until the Device LED light turns on. STEP2 Press and hold both the [DEVICE] button you want to erase and the [PAUSE] button for 5 seconds. The Device LED will blink twice to confirm the erasure. STEP3 To exit, press and hold both the [DEVICE] and [INPUT] buttons simultaneously until the Device LED blinks 3 times. J. Programming the All Off Button J. Programming the All Off Button This allows you to program the All Off button so it can send up to three power On/Off commands with one button press. STEP1 Press the [CBL] button. STEP2 Press the [All OFF] button and the [OK/SEL] button simultaneously for 3 seconds. The [CBL] button will turn on for 30 seconds. STEP3 Press the first [Device] button you want to store in the [ALL OFF] button and then the [POWER] button. Repeat this for other Device until you have stored all the desired power commands into the [ALL OFF] button. STEP4 Press the [CH5] button to save the power commands you stored. The [CBL] button will blink twice to confirm the Device have been saved. K. K. Programming for Programming for Advanced Functions. Advanced Functions. If your remote model has custom- programmable Macro buttons available, they can be programmed to act as a ‘Macro’ or Favorite Channel button in CABLE mode. This allows you to program up to five 2-digit channels, four 3-digit channels or three 4-digit channels that can be accessed With one button press. *Note : The FAV button is not programmable if you have a Digital Cable Box made by Pace, Pioneer or CISCO/SA. STEP1 Press the [CBL] button to select the CBL mode. STEP2 Press the [MACRO] button and [OK/SEL] button simultaneously for 3 seconds. The [CBL] button will turn on for 30 seconds. STEP3 Enter the the 2, 3 or 4-digit code for the channel you want programmed first (for example, 007) using the Number Pad, then press the [STOP] button. Then enter the code for the next channel (for example, 050), then press the [STOP] button. Repeat this process for the third channel. The [CBL] button will blink once for each channel entered. STEP4 Press the [CH5] button to store the channels that were selected. The [CBL] button will blink twice to confirm the storage of commands. To access the programmed channels, press the [MACRO] button once. This will bring up the first channel. Press once again and it will bring up the second channel. Press again and it will bring up the third channel. To erase the Macro programming and return to the original function: STEP1 Press the [CBL] button to trol (i.e. volume, mute, etc.) to ensure you have the correct code. If any of the functions do not operate as they should, repeat the instructions from STEP 3 above using the next three digit code number from the brand list. STEP4 Store the three-digit code by pressing the same [DEVICE] button once again. The device LED will blink twice to confirm that the code has been stored. D. D. Auto Search Method Auto Search Method If none of the three digit code numbers assigned to your brand of equipment works, or the code table does not list your brand, you can use the Auto Search Method to find the correct three-digit code number for your equipment by following steps: STEP1 Turn on the equipment that you want the remote control to operate (Cable Box, TV or DVD). STEP2 Press the [DEVICE] button and the [OK/SEL] button simulta- neously for three seconds. The device LED will turn on indicating that it is ready to be programmed. The LED will remain on for 30 seconds. The next step must be entered while the LED is on. STEP3 Press the [CH5] or [CH6] button one at a time or keep it pressed. The remote will emit a series of Power ON/OFF code signals. Release the [CH5] or [CH6] button as soon as the equipment turns off. *Note: You can verify that you have selected the correct code by pressing the [POWER] button. The equipment should turn back on. Then try all of the functions on the remote con- trol (i.e. volume, mute, etc.) to ensure you have the correct Button Functions 3 Programming the Remote Control 4 Universal Remote Control, Inc. www.universalremote.com OCE-0082B REV 25 (02/20/18) UR3L-SR4 Operating Manual For Easy Clicker This remote control is designed to operate most IPTV and DTA STBs as well as Digital and Analog Cable Boxes. Introduction 1 Replacing Batteries 2 Before you program or operate the remote control, you must install two new AAA alkaline batteries. STEP1 Remove the battery com- partment cover from the back of your remote control. STEP2 Check battery polarity carefully, and install the batteries as shown in the illustration below. STEP3 Replace the battery compartment cover. *Note : In this section, when you are instructed to press a [DEVICE] button, that means you should press either the CBL, TV, or DVD button, depending on which device you are programming the remote to operate. A. Quick Set-Up Method A. Quick Set-Up Method STEP1 Turn on the component you want to program. To program your TV, turn on the TV. 0 PACE DTA 1 SA/CISCO, SAMSUNG, PACE DIGITAL 2 MOTOROLA DIGITAL 3 MOTOROLA DTA 4 EVOLUTION DTA 5 CISCO IPTV 6 ADB IPTV 7 TECHNICOLOR 8 AMINO 140/540 IPTV 9 MOTOROLA IPTV Quick Number Manufacturer/Brand CBL 0 SANYO 1 SONY 2 SAMSUNG 3 LG 4 TOSHIBA 5 PANASONIC 6 PHILIPS 7 HITACHI 8 SHARP 9 VIZIO Quick Number Manufacturer/Brand TV 0 HITACHI 1 SONY 2 PHILIPS 3 SAMSUNG 4 PHILIPS MAGNAVOX 5 PANASONIC 6 LG 7 JVC 8 DENON 9 PIONEER Quick Number Manufacturer/Brand DVD

DVR(TIVO) Manufacturer/Brand Set-Up Code Number CABLE IPTV Manufacturer/Brand Set-Up Code Number DVR(TIVO) Manufacturer/Brand Set-Up Code Number TV Manufacturer/Brand Set-Up Code Number CABLE TV Manufacturer/Brand Set-Up Code Number CABLE TV Manufacturer/Brand Set-Up Code Number TV PIONEER VOYAGER Series 001 007 BA9000 013 SAMSUNG OCAP MODELS 001 007 SiDMedia DC7700X 200 SKY SKY+HD 230 SKY HD 204 Q 240 AP HD, AP Jr 241 TECHNICOLOR 365 TELNET RC-RW100 154 WINDSTERAM KINETIC 212 ADB ADB Series 254 255 ADB5810WX 315 ADB5810W, ADB5721WNX 259 AMINO A125, A130, A530 256 A110 260 AT&T U-VERSE 251 CISCO U-VERSE 251 RNG200 313 CIS330, CIS430 316 COMCAST RNG200 313 DREAM DM7020S, DM7025, DM8000HD 159 ENTONE Amulet IPTV Receiver 258 213 MYRIO IPTV Receiver 254 255 MOTOROLA U-VERSE, VIP1200, VIP1216,VIP1616T, VIP1910, VIP1920, VIP1960, VIP1970 253 NOW TV NOW TV 314 PACE RNG200 313 SCIENTIFIC ATLANTA U-VERSE 251 WEGENER IPTV Receiver 250 ADMIRAL 072 096 081 ADVENT 147 AIWA 141 145 AKAI 070 146 148 124 226 104 108 AKIO 103 ALARON 028 AMARK 112 AMERICA ACTION 043 AMPRO 073 ANAM 043 054 056 080 112 131 AOC 058 070 112 616 APEX 092 APEX DIGITAL 150 037 015 724 AQUAVISION 097 100 686 AUDIOVOX 076 103 043 035 078 224 AUVIO 689 Avera 761 AVIELO 090 AVION 223 AXESS 711 BAYSONIC 043 BELL&HOWELL 072 BENQ 234 BRADFORD 043 BROKSONIC 096 CANDLE 070 002 003 CAPEHART 058 CARVER 164 CELEBRITY 001 CETRONIC 043 CIELO 714 Ciil 732 CINERAL 103 120 CITIZEN 070 002 003 101 103 CLASSIC 043 COBY 640 641 598 CONTEC 043 051 Continu-us 161 746 747 CRAIG 043 054 028 CROSLEY 164 CROWN 043 CURTIS MATHES 070 101 011 072 120 164 081 CXC 043 DAEWOO 076 103 112 043 120 DELL 041 DENON 011 DIGITAL PROJECTION 090 DUMONT 073 DWIN 131 132 DYNASTY 043 FISHER 007 057 ELECTROBAND 001 ELECTROHOME 024 076 ELEMENT 110 622 690 EMERSON 005 028 043 048 076 096 155 051 153 121 ENVISION 070 EPSON 087 228 ESA 031 Evervue 755 FREEMOTION 688 FUJITSU 164 197 028 149 FUNAI 028 043 052 168 FUSION 642 FUTURETECH 043 GATEWAY 165 031 GE 070 073 008 009 034 056 074 155 120 081 GEM 031 GIBRALTER 073 GOLDSTAR 106 112 GRUNPY 028 043 HAIER 116 623 598 749 HANNSPREE 099 HARLEY DAVIDSON 028 HARMAN KARDON 164 HARVARD 043 HISENSE 198 021 619 630 598 752 HITACHI 011 598 007 009 072 010 012 023 158 174 670 749 HP 027 039 098 HUMAX 122 HYPERION 609 HYUNDAI 049 067 ILO 055 096 INFINITY 164 INFOCUS 046 215 225 233 726 733 INKEL 129 INSIGNIA 068 069 078 096 164 168 604 617 INTEQ 073 OPTIMUS 080 OPTOMA 029 OPTONICA 019 081 ORION 096 201 203 204 205 028 PANASONIC 080 164 190 034 056 230 248 524 607 664 PEERLESS-AV 723 763 PHILCO 070 003 024 056 059 060 164 PHILIPS 164 005 218 038 093 070 003 059 199 232 727 743 PIONEER 023 025 135 176 018 070 183 191 214 PLANAR 728 742 POLAROID 026 118 119 006 110 PORTLAND 103 PRISM 034 PROSCAN 722 PROTON 058 171 163 PROTRON 102 213 115 PROVIEW 110 PROX 092 QUASAR 034 056 606 RADIO SHACK 019 043 RCA 156 070 023 024 056 074 209 081 713 751 REALISTIC 007 019 REVOLUTION HD 220 RUNCO 072 073 216 697 SAMPO 070 058 165 SAMSUNG 192 184 185 101 133 089 105 070 655 SANSEI 120 SANSUI 096 078 762 SANYO 007 053 057 020 750 SCEPTRE 036 699 SCOTT 005 028 043 048 113 SEARS 007 028 030 057 094 052 164 015 SEIKI 690 SEMIVOX 043 SEMP 015 SEURA 704 SHARP 081 598 684 019 028 022 692 735 765 766 SHERWOOD 128 SIGNATURE 072 YAMAHA 070 YUPITERU 043 ZENITH 011 072 073 095 103 096 ZONDA 112 ADCOM 203 AIWA 210 AKAI 239 APEX DIGITAL 240 196 ARCAM 165 148 374 BOSE 244 245 CAMBRIDGE AUDIO 224 145 COBY 206 CYBERHOME 170 212 DAEWOO 170 DENON 226 225 358 DURABRAND 235 EMERSON 235 ESA 235 FUNAI 235 GOLDSTAR 182 194 GO VIDEO 228 182 252 253 254 GRADIENTE 243 HARMAN KARDON 217 HITACHI 181 INSIGNIA 235 085 182 178 349 385 INTEGRA 236 128 JVC 185 KENWOOD 166 KISS 237 KLH 230 KOSS 243 KRELL 218 LEXICON 216 LG 182 194 105 350 MAGNAVOX 178 191 195 235 MARANTZ 135 MCINTOSH 167 MEMOREX 222 MERIDIAN 200 MINTEK 240 196 MITSUBISHI 186 MYRYAD 211 NAD 198 182 353 ONKYO 207 236 128 OPPO 125 OPTIMUS 187 ORITRON 243 PANASONIC 076 219 103 104 379 PHILIPS 195 164 191 209 127 381 PIONEER 187 221 223 354 377 POLAROID 085 RCA 086 SANSUI 201 SANYO 215 SAMSUNG 183 228 205 073 152 241 380 SENSORY SCIENCE 254 SHARP 174 SHERWOOD 129 361 SONY 168 190 213 077 118 119 120 121 126 351 368 378 382 SPECTRONIQ 088 SUPERSCAN 235 SV2000 235 SYLVANIA 235 SYMPHONIC 235 TASCAM 185 TAG McLaren 202 THETA DIGITAL 187 TOSHIBA 169 191 206 227 201 236 356 TRUTECH 151 VENTURER 229 VINC 220 087 VIZIO 375 YAMAHA 199 204 246 372 334 383 ZENITH 182 194 CHANNEL MASTER 841 859 DSTV 786 787 788 241 800 HUGHES 817 HUMAX 817 ICREALTIME 111 816 MOXI 112 PHILIPS 790 817 785 RCA 809 Manufacturer/Brand Set-Up Code Number TV Manufacturer/Brand Set-Up Code Number TV Manufacturer/Brand Set-Up Code Number TV Manufacturer/Brand Set-Up Code Number TV Manufacturer/Brand Set-Up Code Number DVD JBL 164 JCB 001 JCPENNEY 008 024 030 070 101 156 JENSEN 013 JVC 038 001 034 083 639 KENWOOD 070 001 KLEGG 220 KLOSS 002 059 KREISEN 202 KTV 070 043 LG 598 086 106 112 741 LODGENET 072 LOEWE 196 164 738 LOGIK 072 LXI 007 052 164 015 081 MAGNAVOX 070 003 022 059 060 061 164 094 056 028 035 211 205 218 050 138 232 MAJESTIC 072 MARANTZ 164 070 143 169 MATSUI 164 MATSUSHITA 080 MAXENT 165 MEMOREX 007 072 028 096 MGA 024 070 MIDLAND 073 MINTEK 077 MINUTZ 008 MITSUBISHI 024 040 146 028 124 200 235 081 MOTOROLA 081 MTC 070 101 MULTITECH 043 NAD 025 015 NEC 070 040 056 007 019 024 717 758 NEXUS 620 078 NIKEI 043 NIKKO 103 NIKO 175 NORCENT 211 NTC 103 NUVISION 084 OLEVIA 219 ONKING 043 ONWA 043 Silo 001 Skyvue 744 SONY 001 608 633 SOUNDESIGN 003 028 043 SOYO 163 SPECTRICON 112 SQUAREVIEW 052 SSS 043 STARLITE 043 SUPRE MACY 002 SUPREME 001 SUNBRITE 633 634 635 236 SUNBRITE TV 605 SVA 046 SYLVANIA 070 003 059 060 164 056 168 121 231 SYMPHONIC 052 168 SYNTAX OLEVIA 219 TANDY 081 TATUNG 056 TCL 705 749 TECHNICS 034 080 TECHNOL ACE 028 TECHVIEW 246 TEKNIKA 002 003 024 028 043 072 101 103 164 TELERENT 072 TERA 172 THOMPSON 166 TNCI 073 TOSHIBA 015 101 045 030 007 040 142 137 703 TRUTECH 212 UNIVERSAL 008 009 UPSTAR 708 VENTURER 721 VIDEO CONCEPTS 146 VIDIKRON 164 VIEWSONIC 210 211 720 VIORE 055 229 192 VISCO 110 VIZIO 236 031 624 625 WARDS 164 008 009 019 028 060 061 072 074 070 W Box Technologies 731 WESTINGHOUSE 076 036 221 222 001 690 695 WINBOOK 079 Set-up Code Tables 5 CBL : CBL TV : CBL DVD : DVD If you wish to store the TV channel controls in TV mode, use the following steps. STEP1 Press the [OK/SEL] button and [TV] button simultaneously for three seconds. The device LED will turn on for 30 seconds. The next step must be performed while the LED is on. STEP2 Press the [VOL6] button. The device LED will blink. STEP3 Press [TV] button. The device LED will blink twice to confirm the programming. Note : To return TV device to CBL channel repeat steps above replacing [TV] with [CBL] in Step 3. N. N. Low Battery Warning Low Battery Warning When the battery is low (2.3V-2.0V) and needs to be replaced with fresh batteries, device LED will blink 2 times in sequence whenever a [DEVICE] button is pressed to turn on equipment. O. O. Memory Lock System. Memory Lock System. This remote control is designed to retain programmed memory for 10 years — even after batteries are removed from the remote control. For additional information about your remote control, go to www.universal- remote.com Manufacturer/Brand Set-Up Code Number TV REPLAY NETWORKS 775 SONY 804 805 Speco Technologies 879 TIVO 790 817 858 TOSHIBA 817 ZUUMMedia 855 CISCO/SA EXPLORER Series 001 007 8600X 011 8600 021 8540,8570,8590 022 8500 023 LogicTV 209 MOTOROLA DCT Series (DVR Model) 002 DTA100 206 GENERAL INSTRUMENT DCT Series,DCH Series, CFT2200 008 DL4,DQNV/DRX,DPBB,DPV/DP/DQN,DRZ 027 JERROLD BMC9012/BMC9022 006 DSR470 005 CFT2000 012 DL4,DQNV/DRX,DPBB,DPV/DP/DQN,DRZ 027 Amino A140, A540, A550 219 ARRIS MG5225,MP2000,MP2050A,MP2150A 172 Frontier 216 Cincinnati Bell ZTE B700-V3 220 COMCAST XFINITY 195 Cox Digital Cable Mini Box 223 DIGEO 2056-MSX 153 Digital Multimedia Technology DMT-205HD 222 DIGITAL STREAM DCS1000 180 Duoson TotalPlay 218 ENTONE Kamai 500 210 Kamai 45x 221 EVOLUTION FTA X0-01 158 EVOLUTION UNIVERSAL SD DTA 189 UNIVERSAL HD DTA 215 Horizon Ziggo 225 KAON Mini 208 MOXI MOXI MEDIA CENTER 006 MOXI HD DVR 052 2056-MSX 153 NAGRA DCI-4136M 211 NAGRAVISION HDDTA 201 NFUSION NUVENIO SD PHOENIX, NUVENIO HD, SOLARIS, NOVA 192 PACE 500 Series 001 007 TDC Series 002 510 004 DC60X 206 IPH8005M 217 Pico Digital VMX1, VMX3, HD-2 224 Manufacturer/Brand Set-Up Code Number DVD