Texecom PRESTIGE HD Installation Instructions

MOUNTING HEIGHT 6 ANGLING THE DETECTOR 4 3 STANDARDS & APPROVALS 2 ENVIRONMENTAL 1 PHYSICAL 8m 26'2" 10m 32'9" 15m 50' 15m 50' 2m 6'7" 2m 6'7" 2m 6'7" 2m 6'7" -35°C (-31°F) to +60°C (+140°F) 150g (5oz) approx. -35°C (-31°F) to +55°C (+131°F) 60mm (2.4”) 40mm (1.6”) 112.25mm (4.4”) 2.5mm (0.1”) ABS QUALITY ASSURANCE WARRANTY 10 year replacement warranty. The Prestige TD is designed to detect the movement of an intruder and activate an alarm control panel. As the Prestige TD is not a complete alarm system, but only a part thereof, Texecom cannot accept responsibility or liability for any damages whatsoever based on a claim that the Prestige TD failed to function correctly. Due to our policy of continuous improvement Texecom reserves the right to change specification without prior notice. All specifications are measured at 20ºC (68ºF). © 2003-2006 Texecom Ltd. Document Ref: PTD/EU/1.0-3 The Prestige TD is protected by UK & International Registered Designs. Registered Design No’s: 3004997, 3004260 & 3004261. Prestige is a Trademark of Texecom Ltd. C e r t i f i c a t e N u m b e r : F M 3 5 2 8 5 Professional Twin Dual PIR INSTALLATION INSTRUCTIONS INS 253-3 Quiescent Current = 10mA @ 12VDC Max Current* = 16mA @ 12VDC *Maximum current measured at detection/warm up ! ! 0.3 - 3.0m/s 1 - 10ft/s 1 2 3 PULSE COUNT www.texe.com Ask your distributor today for the Texecom full colour Product Guide. JP1 JP1 ✗ LED ON LED OFF ✗ DO NOT TOUCH 3.0m/9’10” 2.5m/8’2” 2.0m/6’7” 1.5m/4’11” 7 MOUNTING HEIGHT AND SETTINGS 4m 13'1" 15m 50' 2m 6'7" 2m 6'7" ! ✓ 5 LATCH INPUT FUNCTIONS The latch terminal (see Section 4) can perform several different functions depending on how it is connected: Latch connected to Set Positive (SW+, Set+): The LEDs will be disabled while the system is set. Any detectors triggered while the system is set will indicate this by permanently lighting the alarm LED (upon unsetting the system). Detectors can be reset by taking the latch line high and then low again. Latch connected to Alarm Positive (AL+, A+ve): The first detector activated while the system is set will indicate this with a slowly flashing alarm LED (upon unsetting the system). Detectors activated subsequently will indicate this by permanently lighting the alarm LED. Detectors can be reset by taking the latch line high and then low again. ALARM PIR Right PIR Left Made In England EOL Resistor Selection See Section 14 Detector Standard: Independently certified to TS 50131-2-2 Grade 2 Environmental Class II. System Standard: Suitable for use in a PD 6662/BS EN 50131-1 Grade 2 system. Environmental Class II. EMC: Independently certified to EN 50130-4 : 1996. RF Immunity: No false alarms from 80MHz to 2GHz at 10V/m. Complies with BS EN 61000-4-3 : 2002. Electrostatic Discharge: No false alarms up to 8kV. Complies with BS EN 61000-4-2 : 1995. Fast Transient Immunity: No false alarms up to ±4kV. Complies with BS EN 61000-4-4 : 1995. High Energy Transient Immunity: No false alarms up to ±2kV. Complies with BS EN 61000-4-5 : 1995. Conducted RF Susceptibility: No false alarms at 10Vrms. Complies with BS EN 61000-4-6 : 1996. Conducted & Radiated Emissions: Complies with EN 55022 Class B. Product Identifier: TD

17 WALL MOUNT BRACKET 12 WIRING THE PRESTIGE TD Do not run cable parallel to mains wiring 11 MOUNTING THE PRESTIGE TD For indoor use only 10 COVERAGE PATTERN Volumetric 9 COVERAGE AND PICK-UP 2 2 4 1 3 1 3 4 5 7 5 8 ✗ Seal all holes INS 253-3 See Mounting Height Diagram (Section 7) 6 ✓ ✓ 15m 50’ 15m 50’ 85º 16 CEILING MOUNT BRACKET ✓ ✗ ✓ ✗ ✓ Mount on a stable surface 230V 110V 230V 110V ✓ ✗ 13 CHOOSING A LOCATION Avoid common false alarm sources ✗ ✗ ✗ ✗ ✗ ✗ ✗ ✗ 14 EOL RESISTOR JUMPER LINKS The jumper links JP3 and JP4 (see Section 4) are used to select resistances for End-of-Line (EOL) wiring applications. If EOL wiring is not used, the headers should be left in the default (O/C) position. If the required resistance values are not available, leave the headers in the O/C position and wire in external resistors as normal. EOL Settings for Texecom Panels JP3 JP4 Premier & Premier International 2k2 4k7Cexample EXAMPLES OF EOL JUMPER LINK USE JP3 Selects the End-of-Line resistance. Equivalent to wiring a resistor of the selected value as shown. JP4 Selects the resistance across the alarm relay. Equivalent to wiring a resistor of the selected value as shown. TAMPER - JP3 ALARM - JP4 Double Pole (jumper links not used) Dual End-of-Line (DEOL)