Teli CS8550Di Operation Manual

Model CS8550Di Operation Manual Thank you for purchasing our CS8550Di B/W CCD camera. This operation manual contains many important information such as how to use this equipment correctly and safely. Please read through this manual carefully. After reading, keep this manual by the side of your equipment for your future reference. BEFORE USE - GENERAL SAFETY INSTRUCTIONS This instruction manual contains important information for the operator (user) and/or people around him/her to avoid personal injury, or property damage to him/her or people around him/her by using this product correctly. Prior to use, read this operation manual carefully to fully understand its instructions for correct use. OWNER’S RECORD Please fill in the blank below the model name and product serial number, which is found on bottom chassis of your device. Keep this number for your record. Model Name Serial No. WARNINGS & CAUTIONS [Definition of markings] The meaning of each mark used in this instruction manual is given below. DANGER This mark warns the user that improper use, indicated with this mark, may cause death or severe personal injuries against the user or people around him/her. CAUTION This mark warns the user that improper use, indicated with this mark, may cause personal injuries (*1) or material damages (*2) against the user or people around him/her. Notes *1 : Personal injuries mean wounds, burns, electric shocks, and others for which the person injured need not to be hospitalized nor to be cared for the long term. *2 : Material damages mean any direct or consequential damages related to property or material loss. This mark indicates what the user SHOULD NOT DO. The details of things which the user should not do are described next to this mark. This mark indicates what the user MUST DO. The details of things which the user must do are described next to this mark. This mark indicates that the user must be alert against a possible DANGER. The details of the danger which the user must be aware of are described next to this mark. This mark indicates that the user are given a CAUTION against possible hazards. The details of the caution which the user must be aware of are described next to this mark. ● Handling Precautions DANGER If any overheating sign is observed, discontinue use immediately. In the event that smoke, smell, or any other overheating sign is observed, turn its power switch OFF immediately, and remove its camera cable from camera connector. Do NOT try to continue to use your camera. To do so in spite of a clear sign of a malfunction invites a fire, an electric shock hazard, or any other serious damage. In such case, after confirming that there is no risk of a fire accident, contact us or our dealer/distributor through which you purchased this device for repair service. To avoid hazard, do NEVER attempt to repair it yourself. If any malfunctioning sign is observed, discontinue use immediately. Do NOT try to use this device when it is obviously malfunctioning. (Example: No images on the monitor) In the event of a malfunction, turn its power switch OFF immediately, and remove its camera cable from camera connector. In such case, contact us or our dealer/distributor through which you purchased this device for repair service. If any liquid gets into the device, discontinue use immediately. In the event that water, or any other type of liquid gets into the body, do NOT try to continue to use the device. To do so invites a fire or an electric shock hazard. In such case, turn its power switch OFF immediately, and then remove its camera cable from camera connector. After that, contact us or our dealer/distributor through which you purchased this device for repair service/technical advice. Do NOT disassemble this device. Do NOT attempt to pull apart, repair, or modify your camera yourself. To do so might lead to a fire or an electric shock accident. Contact us or the dealer/distributor from which you purchased the device for repair/modification. Do NOT supply any power other than specified. This device is designed to work only under specified voltage. Do NOT attempt to supply the device with power other than specified. Supplying the device with any unspecified power invites a fire or an electric shock hazard.　(CS8550Di --- DC+12V) Do NOT use the camera in a high-humidity environment. Do NOT place your camera near a humidifier, or in other high-humidity environment. To do so might cause a fire or an electric shock accident. Do NOT use any optional unit other than manufacturer-supplied one. [We disclaim any responsibility for damages or losses incurred by user due to the use of unauthorized / unofficial option units supplied by a third-party] ● Handling Precautions 　CAUTION If the camera is operated in the electromagnetic field, there may be cases where beat noises (vertical, horizontal, or oblique stripes) appear in the video output. In that case, take preventive measures on the electromagnetic-wave generating source so that your camera do not receive the interference by the electromagnetic-wave. Take extra precautions against electromagnetic-wave-interference if your camera is used with a servomotor, inverter, or other electromagnetic-wave-generating equipment. Avoid giving a strong shock against the camera body. It might cause a breakdown or damage. If your camera is used in a system where its camera head is subjected to strong repetitive shocks, its camera head is possible to break down. If you intend to use your camera in such a situation, make sure to use an optional camera-connector-fixing-hardware to connect the connector-plug to the camera body. When the camera is not in use, put a lens or a lens-cap onto the camera head so that the image pickup plane of CCD is protected from dust, foreign object, or any other flaw-causing object. If the glass plane (image pickup plane) gets dirty, clean it with a cotton swab. When it needs to be cleaned with a cleaner, be sure NOT to use any organic solvent other than ethyl alcohol. As a countermeasure against condensation, when the camera is moved from a warm condition/environment to a cold one, take appropriate precautions to prevent condensation from forming on the camera. Do not pull strongly the camera cable/camera-head nor swing it. The stress from pulling or swinging may cause damage in the coating of the cable, or breaks in the inside wires. Avoid short-circuiting signal output. Otherwise, it may cause a malfunction. If too much amount of light, (= the incoming light amount of 100 times or greater in comparison with standard light) enters CCD image pickup plane, video output might not be obtained. In such a case, take measures to reduce the amount of incoming light. Do NEVER expose its camera head to any intensive light (such as direct sunlight). Otherwise, its inner image pickup device might get damaged. CAUTION When mounting a lens, take extra caution so that the lens is not tilted, nor does flaw exist at the lens- mount-screw part. Also check to confirm that no dirt nor other foreign object is put inside. Improper mounting might cause the parts to become locked. Wastes of this product should be separated and discarded in compliance with the various national and local ordinances. RESTRICTION FOR USE In the case where a malfunction of this camera (e.g. video output cut-off) can be expected to lead to a significant accident, avoid using this device for such system build-in use. DISCLAIMER (LIMITED WARRANTY) We assume no responsibility and shall be held harmless for damage or loss incurred by the user in the following cases. 1.In the case where damage or loss is caused by fire, earthquake, or other acts of Gods, acts by a third party, misuse by the user deliberately or erroneously, or use under extreme operating conditions. 2.In the case where any indirect, additional, consequential damages (e.g. loss of expected interest, suspension of business activities) are incurred as results of a malfunction or non-functioning of this device, we shall be exempted from assuming responsibility for such damages. 3.In the case where damage or loss is caused by incorrect use which is not in line with the instructions given in this operation manual. 4.In the case where damage or loss is caused by a malfunction resulting from bad connection with other equipment. 5.In the case where damage or loss is caused by repair or modification done by the user. IMPORTANT SAFETY INSTRUCTIONS (1)This device is designed and guaranteed to work under the temperature range of 0 through 40 degree C. Avoid using the equipment beyond that limits. (2)Do NOT expose the camera’s image-pickup-plane to sunlight or other intense light directly. Its inner CCD (charge-coupled device) might be damaged. (3)In the event that any abnormal condition is observed, turn the power switch OFF immediately. Do NOT try to continue to use the camera. To do so in spite of clear signs of malfunction invites a fire, an electric shock hazard, or any other serious damage to the camera. In such case, contact us or our dealer/distributor from which you purchased the camera for repair service. (4)To clean the body of this equipment, make sure to turn the power switch OFF first. To remove stubborn stains, use a soft cloth soaked in diluted acid-free detergent. After that, clean with a dry cloth. (5)In case the image-pickup-plane should be settled with fine dust, dirt, or scratched, ask our distributor for technical advice. 1. PRODUCT DESCRIPTION Model CS8550Di is a one-body type B/W CCD camera with a VGA format all-pixel-data readout CCD. This model has twice greater driving frequency of conventional cameras to achieve fast-speed data- processing. The model is suited for high-speed, high-resolution image processing use. Its compact, light- weight body is ideal for system integration. 2. FEATURES (1) Double-speed scan This model reads out image-data twice as fast as conventional cameras do. (2) All pixel's data readout With its built-in all-pixel-data-readout CCD, this model can read out image-data just in approximately 1/60 sec. A frame-shutter reads out all data even under RTS (Random Trigger Shutter) mode. (3) High vertical resolution As all pixel's data are read out even under RTS mode (in 1/60 sec.), images with no deterioration in vertical resolution are obtained. (4) Square grid pattern CCD Pixel's in CCD are aligned in square grid pattern. This makes it easier to perform computation correctly for image processing use. (5) External Sync. The camera is switched over to external synchronization operation automatically when external HD signal is input. (6) Random trigger shutter function With a built-in RTS, the camera’s CCD starts light-exposure in synchronization with external trigger signals. This function enables the camera to capture fast-moving subjects at constant position for precise image processing. (7) Restart / Reset Under the restart / reset mode, this model can capture images at an arbitrary timing cued by external VD signal. (8) Multiple shutter With this shutter, this model capture images at an arbitrary timing cued by external trigger signal, and then outputs video at an arbitrary timing cued by external VD signal. (9) Partial-scan Under the partial scan mode, only 1/2 or 1/4 screen center portion of image information is read out, resulting in a faster operation. (10) Ultra-compact & light-weight camera head The model features its ultra-compact and light-weight camera head, freeing you from your integration- space-problem. In addition, it has an excellent shock and vibration resistance. 3. CONFIGURATION (1) Camera body ･･････････････････････････････････････ 1 (2) Accessory Operation Manual(Japanese) ･･･････････････････････ 1 Operation Manual(English) ････････････････････････ 1 4. OPTION UNIT (1) DC SYNC IN cable (Model name: CPRC3700) (2) Camera adapter (Model name: CA170) (3) Camera-mounting kit (4) Camera-connector fixing hardware *Contact your dealer / distributor for details of option units. 5. OPERATION MODE (1)GAIN selection (Camera rear-panel SW) Switches sensitivity setting (1-1)FIX------------------Factory-prefixed gain (1-2)MANU--------------Gain is adjustable via the manual gain potentiometer (M.GAIN) (2) Video output mode selection (Camera rear-panel DIP SW) Switches video format (2-1)1/60: 1/60s----------Non-interlace mode As all pixels are read out in 1/60s, you will get images with the higher V resolution (2-2)1/120: 1/120s-------2:1 interlace MIX mode As vertical pixels are added in readout, the sensitivity is same as that of 1/60s non-interlace mode during electronic shutter OFF. Twice greater sensitivity is obtained under shutter-speed range of 1/200 – 1/20000. (3) TRIG selection (Camera rear-panel DIP SW) Switches TRIG input signal polarity used under RTS mode (3-1)POSI ----------------Positive polarity (rising edge detection) (3-2)NEGA---------------Negative polarity (falling edge detection) (4) RTS (Random Trigger Shutter) exposure selection Switches light exposure mode under RTS mode (4-1)FIX mode----------- Rear DIP SW Exposure-time control via rear-panel DIP switch (4-2)PULSE W mode--- TRIG signal pulse width control Exposure-time control via TRIG signal pulse width (5)Shutter mode selection (Camera rear-panel DIP SW or TRIG signal IN [Automatic]) Switches shutter mode (5-1) NOR mode -------- Normal electronic shutter Exposure control via internal sync signal High-speed shutter: From 1/20,000s through OFF (8 position) (5-2) RDM mode-------- Random trigger shutter Exposure control via ext. trigger or ext. sync. input Timing charts are shown below. (TRIG timing: Positive) Notes: * RDM selection is automatic with TRIG status ** Neither under FIX nor PULSE W mode, RTS doesn’t work if E-shutter speed SW is set in OFF position. (a)Non-reset mode (Under internal sync / external sync --- Consecutive VD IN) Exposure starts at the timing of TRIG signal IN. After each exposure is completed, the camera outputs video at each next VD IN timing. (b)Non-reset mode (Under external sync --- Single VD IN) After TRIG IN and exposure, the camera goes into standby until next ext. VD IN. Under 1/120s 2:1 interlace mode, video output field (ODD/EVEN) is determined by ext. VD falling edge and ext. HD phase. *Don’t provide ext. VD IN during exposure. ** After automatic return, fix ext. VD IN at Hi. (c)V-reset mode (Under internal sync / external sync --- No VD IN) Exposure starts at the timing of TRIG signal IN. After each exposure is completed, the camera outputs video immediately by resetting VD. (HD is not reset) Under 1/120s 2:1 interlace mode, irrespective of TRIG IN phase, the camera always outputs ODD field image. (d)SYNC reset mode (Under internal sync) Exposure starts at TRIG signal input timing, resets HD, and outputs video immediately after exposure by resetting VD. * Available under FIX mode only. Under 1/120s 2:1 interlace mode, irrespective of TRIG IN phase, the camera always outputs ODD field image. (5-3) MULTIPLE mode Multiple shutter operation is available by providing TRIG IN more than one time before ext. VD IN. (Non-reset mode, single VD, consecutive VD IN) Under 1/120s 2:1 interlace mode, video output field (ODD/EVEN) is determined by ext. VD falling edge and ext. HD phase. (5-4) Restart / Reset The restart / reset function is available with the ext. VD signal. You can get an arbitrary slower shutter speed than normal shutter and random trigger shutter. Here are some notes; * The shutter speed (exposure time) is determined by ext. VD signal interval. ** This function is enabled when the rear-panel shutter speed DIP SW is OFF. *** Supply consecutive VD. Under 1/120s 2:1 interlace mode, video output field (ODD/EVEN) is determined by ext. VD falling edge and ext. HD phase. (6)Partial-scan mode selection (Camera rear-panel DIP SW) Switches partial-scan mode Note: Sometimes phenomenon called as “whiteout” occurs at the top of the screen when there is strong incident light entering in the wide area of a CCD, however, this is not a malfunction. If this occurs, reduce the amount of incoming rays. (6-1)1/2 Partial-scan (Rear-panel SW: 7-OFF, 8-ON) --- Screen center 1/2 readout □ 1/60s Non-interlace Under 1/60s non-interlace mode, only the center portion of 220H out of the total effective lines 492H (excluding BLK time) is read out. Available both under external / internal mode. Under normal shutter (Electronic shutter OFF) Notes: * Under ext. sync, the ext. VD should be 1V = 262H. ** Under normal shutter, set the rear-panel DIP SW #5, #6 in OFF. ■ Under other shutter modes □ 1/120s 2:1 Interlace Under 1/120s interlace mode, only the center portion of 207H out of the total effective lines 485H (excluding BLK time) is read out. Available both under external / internal mode. ■ Under normal shutter (Electronic shutter OFF) Notes: * Under ext. sync, the ext. VD should be 1V = 131.5H. ** Under normal shutter, set the rear-panel DIP SW #5, #6 in OFF. ■ Under other shutter modes TOKYO ELECTRONIC INDUSTRY CO., LTD. ! ! ! DON’T DON’T ! CAUTION! MUST MUST MUST NEVERpullapart CAUTION! CAUTION! CAUTION! CAUTION! CAUTION! Video output CCD Exposure Ext VD IN The exposure time is determined by VD interval. WEN OUT (Negative) CAUTION! Video output Exposure time (E-shutter-speed or pulse width) CCD Exposure TRIG IN (Positive) Outputs video at the next VD timing after exposure Automatically returns to normal shutter if fixed H level (after approx. 1/6s) Random trigger shutter Normal shutter Normal shutter TRIG IN not acceptable for 1V after mode change Definite Ext VD In In sync with ext. VD during standby (No video output) WEN OUT (Negative) VD, V-sync pause during standby Video output Exposure time (E-shutter-speed) CCD Exposure TRIG IN (Positive) Automatically returns to normal shutter if fixed H level (after approx. 1/6s) Random trigger shutter Normal shutter Normal shutter TRIG IN not acceptable for 1V after mode change Definite WEN OUT (Negative) VD, V-sync output for 1V only Video output CCD Exposure TRIG IN (Positive) Ext VD IN Exposure time (E-shutter speed or pulse width) Three exposures are mixed and output here. WEN OUT (Negative) 28H 220H VIDEO OUT Video output time V BLK (Include High-speed transfer) 14H 141 High- speed transfer 360 141 360 262H 262H WEN OUT (Negative) 9H 9H 9H 28H 220H *1 VIDEO OUT Video output time *1 Arbitrary under ext. sync V BLK (Include High-speed transfer) 14H 141 High- speed transfer 360 WEN OUT (Negative) 9H 9H 21H 103H VIDEO OUT Video output time V BLK (Include High-speed transfer) 7H 154 155 High- speed transfer 358 359 153 154 359 360 20.5H 104H Video output time 7H High- speed transfer 0.5H V BLK (Include High-speed) 131.5H 131.5H ODD image EVEN image WEN OUT (Negative) 9H 8.5H 9H 20.5H 104H *1 VIDEO OUT Video output *1 Arbitrary under ext. sync V BLK (Include High-speed transfer) 7H 153 154 High- speed transfer 359 360 21H 103H *1 VIDEO OUT Video output V BLK (Include High-speed transfer) 7H 154 155 High- speed transfer 358 359 ODD image EVEN image WEN OUT (Negative) WEN OUT (Negative) 9H 8.5H 8.5H 9H CAUTION! Video output Exposure time (E-shutter speed or pulse width) CCD Exposure TRIG IN (Positive) Outputs video at the next VD timing after exposure Automatically returns to normal shutter if fixed H level (after approx. 1/6s) Random trigger shutter Normal shutter Normal shutter TRIG IN not acceptable for 1V after mode change Definite Int / Ext VD Outputs VD, V-sync during standby WEN OUT (Negative) Video output Exposure time (E-shutter-speed or pulse width) CCD Exposure TRIG IN (Positive) Automatically returns to normal shutter if fixed H level (after approx. 1/6s) Random trigger shutter Normal shutter Normal shutter TRIG IN not acceptable for 1V after mode change Definite VD, V-sync pause during standby WEN OUT (Negative) VD, V-sync output for 1V only DON’T ! MUST

□ 1/60s Non-interlace Under 1/60s non-interlace mode, only the center portion of 75H out of the total effective lines 492H (excluding BLK time) is read out. Available both under external / internal mode. ■ Under normal shutter (Electronic shutter OFF) Notes: * Under ext. sync, the ext. VD should be 1V = 131H. ** Under normal shutter, set the rear-panel DIP SW #5, #6 in OFF. ■ Under other shutter modes □ 1/120s 2:1 Interlace Under 1/120s interlace mode, only the center portion of 61H out of the total effective lines 485H (excluding BLK time) is read out. Available both under external / internal mode. ■ Under normal shutter (Electronic shutter OFF) Notes: * Under ext. sync, the ext. VD should be 1V = 65.5H. ** Under normal shutter, set the rear-panel DIP SW #5, #6 in OFF. ■ Under other shutter modes 6. SPECIFICATIONS [Basic spec] (1)Image sensor All Pixel’s Data Read Total pixels 692(H) x 504(V) Active pixel 659(H) x 494(V) Video output pixels 648(H) x 492(V) (Under non-interlace) Scanning area 4.88(H) x 3.66(V) mm (= Equivalent to 1/3” type CCD size) Unit cell size 7.4(H) x 7.4(V) µm (Square-grid array) (2)Scanning lines 525 lines (3) TV system Special format (Non-conforming to EIA/CCIR) (4)Interlace 1/60s Non-interlace mode 1/120s 2:1 Interlace mode Switching via rear-panel DIP SW (5)Sync system Internal/External automatic switch-over (6)Aspect ratio 4:3 (7)Video output VS 1.0V(p-p) / 75 Ω, DC coupled, 1 line (8)Resolution 485 TV lines(H) 485 lines (350 TV lines)(V) (9)S/N Standard: 52dB(p-p)/rms (Initial factory setting) (10)Illumination Standard 400 lx (F5.6) Minimum 4 lx (F1.4) (GAIN MAX, Approx. 50 % video output) (11)Gain FIX (Fixed) gain: Factory-shipped preset level MANU (Manual) gain: Setting through GAIN VR FIX / MANU switching via rear-panel DIP SW (12)Gamma correction Gamma = 1 (Fixed) (13)White-clip level Approx. 840mV(p-p) (Excluding SYNC) (14)Power source DC12V ±10 % Ripple voltage: 50mV(p-p) or less (15)Power consumption Approx. 1.8W [Internal sync spec] (1)Base clock frequency 24.545MHz (1CLK) ± 200ppm (2)H sync frequency 31.468kHz (1H = 780CLK) (3)V sync frequency 59.94Hz (Under non-interlace) 119.88Hz (Under 2:1 interlace) [External sync spec] (1)Ext. sync input signal HD/VD (2)Input level 2~4V (p-p)/10kΩ (3)Input impedance 75Ω / High impedance (switching via rear-panel SW) (Initial factory setting: High) (4)Interlace 1/60s non-interlace or 1/120s 2:1 interlace (5)Polarity Negative (6)Pulse width HD: 3.2 ± 1 µs (LOW) VD: From 125 through 400 µs (LOW) (7)Repeating frequency fH = 31.468kHz ±1% fV = fH/262.5 or fH/525 (8)Phase difference HD/VD: 0 ±5.0 µs, 1/FH/2 ±5.0 µs [Shutter trigger spec] Exposure-starting-cue signal in random trigger shutter mode (1)Input level LOW level: 0~0.5V(p-p) HIGH level: 4~5V(p-p) (2)Input impedance High impedance (10kΩ) (3)Capture timing Rising edge detection (Positive) / Falling edge detection (Negative) (Switching via rear-panel DIP SW) (Initial factory setting: Rising edge) (4)Pulse width Minimum 2 µs Maximum 1/8s [Sync signal spec] WEN readout timing pulse (1)Polarity Negative (Positive as option) (2)Pulse width 1H output WEN OUT 100 50 WEN 2SC4176 2SA1610 5V [Electronic shutter spec] (1)Normal shutter Shutter-speed setting via rear-panel SW (Initial: OFF) Selection among 8 scales (= OFF, 1/200s, 1/500s, 1/1000s, 1/2000s, 1/4000s, 1/8000s, 1/20000s) (2)RTS (a)Operation mode No. Reset Exposure Sync 1 Internal 2 Consecutive HD / Consecutive VD IN 3 Consecutive HD / Single VD IN 4 Internal 5 Consecutive HD / Consecutive VD IN 6 Consecutive HD / Single VD IN 7 Internal 8 Consecutive HD IN 9 SYNC reset Internal 10 Internal 11 Consecutive HD IN Rear SW (FIX mode) V reset V-reset Non-reset Rear SW (FIX mode) TRIG pulse width (PULSE mode) TRIG pulse width (PULSE mode) *RTS shutter mode automatically switches over through TRIG IN **RTS disabled under electronic shutter OFF (b)Multiple shutter Multiple shutter via ext. trigger signal and ext. VD signal *Operation like No.3, 6 above (3)Restart / Reset Restart / reset available via ext. VD signal (Switching via rear panel DIP SW, Initial OFF) Notes: *The exposure-time (shutter-speed) is determined by ext. VD interval. **Enabled when rear-panel DIP SW OFF. ***Provide Consecutive HD. [Mechanical spec] (1)External dimension 29 x 29 x 39.5(D)mm (Not including protrusion) Refer to the attached external view drawing (2)Weight Approximately 50g (3)Lens mount C mount (4)GND / insulation Circuit GND ~ Chassis electrically conducted [Ambient condition] Performance guaranteed: Temperature: From 0 through 40 °C Humidity: From 30 through 90 % (No condensing) Operation guaranteed: Temperature: From -5 through 50 °C Humidity: From 10 through 90 % (No condensing) Storage: Temperature: From -20 through 60 °C Humidity: From 10 through 90 %(No condensing) EMI Conforms to EN50081-2 [Connector pin assignment] (1)Compatible connector HR10A-10P-12S (Supplied by HIROSE ELEC.) (2)Pin assignment Pin No. Signal (Standard) 1 DC12V GND 2 DC12V 3 VIDEO GND 4 VIDEO OUT 5 HD GND 6 HD IN 7 VD IN 8 TRIG GND 9 NC 10 WEN OUT 11 TRIG IN 12 VD GND *Before connecting / disconnecting the connector, make sure the camera power is OFF. **For board connection, check compatibility. [Switch setting] (1) CCU rear-panel DIP SW No. Function OFF ON 1 2 3 4 Video output mode 1/60s non-interlace 1/120s interlace 5 6 7 8 9 TRIG polarity (TRIG) Positive (Rising edge) Negative (Falling edge) 10 RTS Exposure (EXP) FIX mode PULSE W mode Shutter mode (SMODE) E-shutter- speed (SHUT) Partial scan (PART) See shutter-speed table (Table 1) See shutter-mode table (Table 3) See partial-scan table (Table 2) 1 O N 2 3 4 5 6 7 8 9 0 VI DEO VI DEO VI DEO VI DEO SHUT SHUT SHUT SHUT SMODE SMODE SMODE SMODE PART PART PART PART TRI G TRI G TRI G TRI G EXP EXP EXP EXP *Initial factory setting: All OFF **Set No.9 OFF when TRIG IN OPEN. (Table 1) Electronic shutter-speed Shutter-speed No.1 No.2 No.3 OFF OFF OFF OFF 1/200s ON OFF OFF 1/500s OFF ON OFF 1/1000s ON ON OFF 1/2000s OFF OFF ON 1/4000s ON OFF ON 1/8000s OFF ON ON 1/20000s ON ON ON *Don’t set Electronic shutter-speed in OFF under RTS mode. (Table 2) Partial-scan Partial scan No.7 No.8 OFF OFF OFF Not acceptable ON OFF 1/2 partial OFF ON 1/4 partial ON ON (Table 3) Shutter-mode No.5 No.6 V reset OFF OFF SYNC reset ON OFF Non-reset OFF ON ON ON Non-reset (Multiple shutter) OFF OFF Single VD Non-reset ON OFF Consecutive VD V-reset OFF ON No VD ON ON Single VD Restart / Reset SYNC Internal sync Ext. sync HD IN Random trigger Random trigger Shutter mode Not acceptable *Under normal shutter mode partial-scan, set No.5, 6 in OFF. **Under PULSE W mode, SYNC reset is disabled. (2) CCU rear-panel SW Function SW Selected Function HIGH High impedance (Initial factory setting) 75Ω 75Ω F Factory-set GAIN Ext. SYNC IN impedance (HD / VD) GAIN selection (GAIN) M Manual GAIN adjustable via GAIN potentiometer 7. TIMING CHART (1)H rate timing (2)1/60s Non-interlace mode (3)1/120s 2:1 Interlace mode 8. EXTERNAL VIEW DRAWING Head Office : 4-7-1, Asahigaoka, Hino-shi, Tokyo 191-0065, Japan Phone: +81-(0)42-589-8771 FAX: +81-(0)42-589-8774 Kansai Branch : Nitto Building, 2-1-2, Sakaemachi-dori, Chuo-ku, Kobe, Hyogo 650-0023, Japan, Phone : +81-(0)78-321-3461 FAX : +81-(0)78-321-3463 Fukuoka Office : Yen Building, 2-7-21, Hirao, Chuo-ku, Fukuoka 810-0014, Japan Phone : +81-(0)92-523-3395 FAX : +81-(0)92-523-3397 The design and specification is subject to change without notice. ① ② ③ ④ ⑤ ⑥ ⑦ ⑧ ⑨ ⑩ ⑪ ⑫ 12 pin male Connector pin layout O B 3 1 O B 1 O B 1 O B 2 1 7 8 6 5 5 6 5 6 6 5 9 6 5 6 6 5 9 6 5 5 D 1 D 1 6 Opt.Blk. H.trans. pause Dummy pixels Opt. Blk. Effective pixels = 659CLK H. blanking 132CLK(5.38µµµµssss) V-OUT Effective pixels CAM VIDEO OUT 18CLK (0.73µµµµssss) 60CLK (2.44µµµµssss) 54CLK (2.20µµµµssss) 648CLK (26.40µµµµssss) Horizontal scan (1H) 780CLK(31.78µµµµssss) 4CLK 31CLK 72CLK 16CLK 2CLK 7CLK 648CLK 4CLK H.SYNC EXT HD ±±±± 0.5µµµµs 78CLK (3.18µµµµssss) INT HD 1CLK=40.74ns WEN OUT 9H 20H V. Blanking INT VD INT HD VIDEO OUT EXT VD IN 523 524 525 19 20 21 22 23 24 25 26 27 28 29 30 31 32 491 492 493 494 1H delay WEN OUT (Negative) 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 489 490 487 488 OB OB 33 34 35 2 3 4 5 OB 1 OB OB OB OB OB OB OB 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 ODD (1st field) 32 33 34 35 36 37 9H 20H V. Blanking INT VD INT HD VIDEO OUT EXT VD IN 260 261 262 281 282 283 284 285 286 287 288 289 290 291 292 293 294 492 493 494 OB 1H delay 263 264 265 266 267 268 269 270 271 272 273 274 275 276 277 278 279 280 490 491 488 489 OB 295 296 297 7 8 9 10 OB OB OB OB OB OB OB OB 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 EVEN (2nd field) 486 487 1 2 3 4 5 6 WEN OUT (Negative) 1H 1H TOKYO ELECTRONIC INDUSTRY CO., LTD. 35H 75H VIDEO OUT Video output time V BLK (Include High-speed transfer) 21H 211 High- speed transfer 285 211 285 131H 131H WEN OUT (Negative) 9H 9H 9H 35H 75H *1 VIDEO OUT Video output time *1 Arbitrary under ext. sync V BLK (Include High-speed transfer) 21H 211 High- speed transfer 285 WEN OUT (Negative) 9H 9H 24H 30H VIDEO OUT Video output V-BLK (Include High-speed transfer) 11H 214 215 High- speed transfer 272 273 213 214 273 274 23.5H 31H Video output 11H High- speed transfer 0.5H V-BLK (Include High-speed transfer) 65.5H 65.5H ODD image EVEN image WEN OUT (Negative) 9H 8.5H 9H 23.5H 31H *1 VIDEO OUT Video output *1 Arbitrary under ext. sync V BLK (Include High-speed transfer) 11H 213 214 High- speed transfer 273 274 24H 30H *1 VIDEO OUT Video output V BLK (Include High-speed transfer) 11H 214 215 High- speed transfer 272 273 ODD image EVEN image WEN OUT (Negative) WEN OUT (Negative) 9H 8.5H 8.5H 9H 9H 33H V. Blanking INT VD INT HD VIDEO OUT EXT VD IN 523 524 525 19 20 21 22 23 24 25 26 27 28 29 30 31 32 492 493 491 494 OB OB OB 1H delay 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 33 34 35 OB OB OB OB OB OB OB 1 2 3 WEN OUT (Negative) 1H Picture Rear-camera connector (Rear-view)