MRC S2D-300 Operating Manual

S2D-300 S2D-400 1. PRODUCT DESCRIPTION 2. USER CONSIDERATION 3. USER OPERATION 4. ACCESSORY 5. MAINTENANCE AND CLEANING 6. FAULTY RUNNING 7. WARRANTY Operating Manual Operating Manual

* Speed range (45~400rpm) * Orbital range (28mm) * Speed range (45~400rpm) Change between orbital or reciprocating motion Smooth and powerful orbital or reciprocating motion at a low speed Optional platform available for flasks LED display (shown actual speed or time) High quality permanent brushless DC motor for gentle and powerful motion Continuous or timed operation PRODUCT DESCRIPTION 1 Characteristics S2D-400 S2D-300 (Platform W400mm x D400mm) (Platform W300mm x D300mm)

Tachometer/time Speed control PRODUCT DESCRIPTION 2 Specification Description Model S2D-300 Free Voltage (AC100 ~ 240V) W430mm x D520mm x H140mm 17 kg Dimensions(mm) Weight Power BLDC motor Motor 28mm Orbital range 45 ~ 400 rpm Speed Timer Loadable weight 6 kg Temp. Resist Lower than 55˚C Platform(mm) W400mm x D400mm Wattage Speed range S2D-400 13 kg 14mm 4 kg W300mm x D300mm 30W W320mm x D410mm x H140mm 99hour 59 min

- If problems occur during the shaking process. - Before you start cleaning the unit. - Never use the appliance if the plug, the cord or the appliance it self is damaged. Be careful not to drop any chemical liquid and water on the instrument to prolong the life of the instrument and protect electronic shock. For example, PEG could be reason for the paint on the surface to be peeled off. Environmental conditions - Indoor use. - Environment temperature 5˚C to 40˚C. - Maximum relative humidity 80% for temperatures up to 31˚C decreasing linearly to 50% relative humidity at 40 C. - Mains supply voltage fluctuations not to exceed 10% of the nominal voltage. - Other supply voltage fluctuations as stated by the manufacturer. - Transient overvoltages according to installation categories. 3 1 User consideration USER CONSIDERATION Power switch is in the "on" position and operate it after 3 seconds for stable using of product.

controlling the rotation. If you want to do "Timer Setting", the last two numbers of the " " on the screen will be blinking when you push the button. The maximum time period is 99hours and 59min. Plug the power cord into the wall receptacle. When you turn on the power switch. " " signal is going to be appeared on the screen. In case of you are dealing with speed control, there will be the red light on the rpm part, and you can check the current speed through the screen. STOP rpm ● time ● RUN MODE STOP RPM/TIMER 0000 STOP rpm ● time ● RUN MODE STOP 0000 0000 0000 0000 0000 User operation USER OPERATION 4 RPM/TIMER

controlling the rotation. If you want to finish the Timer Setting, please kindly push the , then it will be changed as RPM mode. For example when you want to do " Timer Setting" for 5 minutes, push button repeatedly until the number "5" appears on the screen. Then, when you push the button, the setting will be finished. In case of you push button there will be the yellow light on the part of "TIME", and then the timer will be operating. cf) The number of timer is going to be lessened such as 60, 59, 58... STOP rpm ● time ● RUN MODE STOP 0005 5 If the timer setting finishes, there will be an automatic buzz sounds for 3 times for 4 seconds each, and the signal "END", it will be appeared on the screen. 7 Control the shaking speed. (45~400rpm) STOP rpm ● time ● RUN MODE STOP STOP rpm ● time ● RUN MODE STOP 0005 E p Speed fast RPM/TIMER RPM/TIMER RPM/TIMER User operation USER OPERATION 5

FT302-50-13 FT302-100-13 FT302-250-8 FT302-500-5 FT402-50-25 FT402-100-25 FT402-250-14 FT402-500-9 2D Silicon Rack-300 2D Silicon Rack-400 PLATE / FT302 PLATE / FT402 User Operation USER OPERATION & ACCESSORIES Accessory

1.Lift the rubber pad out of the shaking plate 2. Loosen 4 bolt on the four corners of the shaking plate. 3. Also, loosen 4 bolts in middle of the BASE PLATE 4. ORBITAL → RECIPROCATING motion - the base plate rotated 90 degrees and bolt up in holes NO.① 5. RECIPROCATING → ORBITAL motion - the base plate rotated 90 degrees and bolt up in holes NO.② Bolt Base plate Main body ① ② User Operation USER OPERATION

1. Loosen 4 bolts on the four corners of the shaking plate. 2. The 4 posts stood on holes on each corner. And put silicon rack down in there. 3. Fasten 4 screw bolts with posts. User Operation USER OPERATION

Never immerse the appliance in water. 9 Never use the instrument if the plug, the cord or the instrument itself is damaged. The equipment is maintenance-free. Clean the surfaces of the shakers at regular interval. . Water containing a surfactant detergent additive. . Turn the power ON/OFF control button to position OFF . Pull the mains plug . Clean the surfaces of the shaker Maintenance and Cleaning MAINTENANCE AND CLEANING & FAULTY RUNNING

Please, Checking the electronic fuse on the back of main body. 10 If the equipment have other defects, it should be informed to an authorised servicing agent. - In this case, the electronic fuse is broken. If you see the back of the incubator, the fuse box could be seen. After detaching the box as the pictures, change the fuse. spare fuse remove used fuse MAINTENANCE AND CLEANING & FAULTY RUNNING Faulty running

Limited Warranty : This equipment has been tested all the functions and parts for proper operation before shipment. Please read this manual carefully. If you have any questions or problems, check with your dealer or write us direct. This equipment is warranted for a period of 1years from date of purchase against defects in workmanship and material only. If a system component should ever fail to work perfectly, It can be repaired or replaced by our after-sales service without difficulty. Model#: Serial# : Date Purchased : Dealer Name : City and Country : WARRANTY WARRANTY Warranty