Supermicro SuperServer 2028R-C1R(T)4+ Quick Reference Manual

Rear View CPU Installation Front View & Interface  Heatsink Installation 1. Place heatsink on top of installed CPU 2. Line up the four screws to socket 3. Push down heatsink and screw down as shown (cross pattern, in order: A, C, B, D) 4. NOTE: Only use 6-8 lb/f of torque; otherwise, hand-tighten each screw, to avoid damaging the system Memory Caution Align CPU to socket; install CPU straight down NOTE: Do not bend pin inside socket  ! Screw #B Screw #D Screw #A Screw #C PCI Expansion Slots UID Button VGA Port LAN 1/2/3/4 Ports 1 2 3 4 Description No. USB 0/1/2/3 Ports Dedicated LAN for IPMI COM Port Redundant Power Supply Modules 5 6 7 8 SAFETY INFORMATION IMPORTANT: See installation instructions and safety warning before connecting system to power supply. http://www.supermicro.com/about/policies/safety_information.cfm WARNING: To reduce risk of electric shock/damage to equipment, disconnect power from server by disconnecting all power cords from electrical outlets. If any CPU socket empty, install protective plastic CPU cap CAUTION: Always be sure all power supplies for this system have the same power output. If mixed power supplies are installed, the system will not operate. For more information go to : http://www.supermicro.com/support  !  !  ! T-SGPIO1 T-SGPIO2 JD1 JS39 LEDS6 LEDS5 LEDM1 LE2 LE1 FANB FANA FAN4 FAN3 FAN2 FAN1 FAN5 FAN6 JBT1 JIPMB1 SP1 JPS7 JPG1 JPLAN1 JPLAN2 JP JI2C2 JVRM1 JPB1 JTPM1 JSD2 JSD1 JOH1 JS1 JPP0 JPP1 JPWR2 JPWR1 J24 JPI2C1 SAS 4~7 (3.0) SAS 0~3 (3.0) P1-DIMMD3 P1-DIMMD2 P1-DIMMD1 P1-DIMMC3 P1-DIMMC2 P1-DIMMB3 P1-DIMMB2 P1-DIMMB1 P1-DIMMA3 P1-DIMMA2 P2-DIMMH3 P2-DIMMH2 P2-DIMMH1 P2-DIMMG3 P2-DIMMG2 P2-DIMMF3 P2-DIMMF2 P2-DIMMF1 P2-DIMME3 P2-DIMME2 USB 7/8 (3.0) USB 0/1 P1-DIMMC1 P1-DIMMA1 CPU2 SLOT6 PCI-E 3.0 X8 CPU2 SLOT5 PCI-E 3.0 X16 CPU2 SLOT4 PCI-E 2.0 X4 IN X8 JL1 S-SATA0 CPU1 SLOT3 PCI-E 3.0 X16 S-SATA1 S-SATA2 CPU2 SLOT2 PCI-E 3.0 X8 S-SATA3 I-SATA0 I-SATA3 I-SATA4 I-SATA1 CPU2 SLOT1 PCI-E 3.0 X8 COM2 I-SATA5 UID LAN3/4 LAN1/2 IPMI_LAN COM1 CPU2 CPU1 P2-DIMME1 P2-DIMMG1 I-SATA2 JI2C1 CLOSE 1st OPEN 1st CLOSE 1st OPEN 1st USB 6 (3.0) BIOS USB2/3 S-SGPIO1 X10DRC/i-LN4+(-T4+) BMC LAN CTRL LSI 3108 SAS CTRL Intel PCH USB4/5 (3.0) JBAT1 TPM/PORT80 JUIDB1 Front CTRL Panel JF1 FANC JVRM2 JSTBY1 1 LAN CTRL 13 12 Description No. CPU2 Slot1 PCI-E 3.0 x8 CPU2 Slot2 PCI-E 3.0 x8 CPU1 Slot3 PCI-E 3.0 x16 CPU2 Slot4 PCI-E 2.0 x4 (in x8) CPU2 Slot5 PCI-E 3.0 x16 CPU2 Slot6 PCI-E 3.0 x8 DIMME1(Blue)/DIMME2/DIMME3 slot DIMMF1(Blue)/DIMMF2/DIMMF3 slot CPU2 DIMMH1(Blue)/DIMMH2/DIMMH3 slot DIMMG1(Blue)/DIMMG2/DIMMG3 slot DIMMA1(Blue)/DIMMA2/DIMMA3 slot DIMMB1(Blue)/DIMMB2/DIMMB3 slot CPU1 (Install CP1 first) DIMMD1(Blue)/DIMMD2/DIMMD3 slot DIMMC1(Blue)/DIMMC2/DIMMC3 slot SAS 0~3 & SAS 4~7: SAS 3.0 connections supported by the LSI 3108 controlller JBT1: Clear CMOS JSD1: SATA DOM (Device on Module) Power Connectors (I-)SATA 0~5: SATA 3.0 supported by Intel PCH (I-SATA 0~5) (S)SATA 0~3: SATA 3.0 supported by Intel SCU (S-SATA 0~3) 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 16 15 14 19 17 18 21 1 2 3 4 5 6 7 8 10 11 9 20 Beep Code/LED Error Message Description 1 beep Refresh Ready to boot 5 short beeps + 1 long beep Memory error No memory detected in the system 5 beeps No Con-In or No Con- Out devices Con-In includes USB or PS/2 keyboard, PC or Serial Console Redirection, IPMI KVM or SOL. Con-Out includes Video Controller, PCI or Serial Console Redirection, IPMI SOL 1 beep per device Refresh 1 beep or each USB device detected Beep Codes Hard Drive Signal Hard Drive Fail Power Button Reset Button Device Activity LED LAN1 LED Overheat & Fan Fail LED Power LED LAN2 LED Power Failure LED 1 2 3 4 5 6 7 8 9 10 Description No. 3 4 5 6 7 2 1 8 9 10 1 3 8 2 4 5 6 7 HDD0~7 HDD8~15 Type Ranks Per DIMM and Data Width DIMM Capacity (GB) Speed (MT/s); Voltage (V); Slot Per Channel (SPC) and DIMM Per Channel (DPC) 1 Slot Per Channel 2 Slots Per Channel 3 Slots Per Channel 1DPC 1DPC 2DPC 1DPC 2DPC 3DPC 4Gb 8Gb 1.2V 1.2V 1.2V 1.2V 1.2V 1.2V SRx4 8GB 16GB 2133 2133 1866 2133 1866 1600 SRx8 4GB 8GB 2133 2133 1866 2133 1866 1600 DRx8 8GB 16GB 2133 2133 1866 2133 1866 1600 DRx4 16GB 32GB 2133 2133 1866 2133 1866 1600 QRx4 32GB 64GB 2133 2133 2133 2133 2133 1600 8Rx4 64GB 128GB 2133 2133 2133 2133 2133 1600 DIMM Module Population Configuration RDIMM RDIMM RDIMM RDIMM LRDIMM LRDIMM2DS† DDR4 Memory POR for Haswell-EP Processor and Memory Module Population for Optimal Performance Number of CPUs+DIMMs (For memory to work properly, please follow the instructions below.) 1 CPU & 2 DIMMs CPU1 P1-DIMMA1/P1-DIMMB1 1 CPU & 4 DIMMs CPU1 P1-DIMMA1/P1-DIMMB1, P1-DIMMC1/P1-DIMMD1 1 CPU & 5~8 DIMMs CPU1 P1-DIMMA1/P1-DIMMB1, P1-DIMMC1/P1-DIMMD1 + Any memory pairs in P1- DIMMA2/P1-DIMMB2/P1-DIMMC2/P1-DIMMD2 slots 2 CPUs & 4 DIMMs CPU1 + CPU2 P1-DIMMA1/P1-DIMMB1, P2-DIMME1/P2-DIMMF1 2 CPUs & 6 DIMMs CPU1 + CPU2 P1-DIMMA1/P1-DIMMB1/P1-DIMMC1/P1-DIMMD1, P2-DIMME1/P2-DIMMF1 2 CPUs & 8 DIMMs CPU1 + CPU2 P1-DIMMA1/P1-DIMMB1/P1-DIMMC1/P1-DIMMD1, P2-DIMME1/P2-DIMMF1/P2-DIMMG1/P2-DIMMH1 2 CPUs & 8~16 DIMMs CPU1/CPU2 P1-DIMMA1/P1-DIMMB1/P1-DIMMC1/P1-DIMMD1, P2-DIMME1/P2-DIMMF1/P2-DIMMG1/ P2-DIMMH1 + Any memory pairs in P1, P2 DIMM slots 2 CPUs & 16 DIMMs CPU1/CPU2 P1-DIMMA1/P1-DIMMB1/P1-DIMMC1/P1-DIMMD1, P2-DIMME1/P2-DIMMF1/P2-DIMMG1/P2-DIMMH1, P1-DIMMA2/P1-DIMMB2/P1-DIMMC2/P1-DIMMD2, P2-DIMME2/P2-DIMMF2/P2-DIMMG2/P2-DIMMH2 2 CPUs & 16~24 DIMMs CPU1/CPU2 P1-DIMMA1/P1-DIMMB1/P1-DIMMC1/P1-DIMMD1, P2-DIMME1/P2-DIMMF1/P2-DIMMG1/P2-DIMMH1, P1-DIMMA2/P1-DIMMB2/P1-DIMMC2/P1-DIMMD2, P2-DIMME2/P2-DIMMF2/P2-DIMMG2/P2-DIMMH2, P1-DIMMA3/P1-DIMMB3/P1-DIMMC3/P1-DIMMD3, P2-DIMME3/P2-DIMMF3/P2-DIMMG3/P2-DIMMH3 Processors and their Corresponding Memory Modules CPU# Corresponding DIMM Modules CPU 1 CPU 2 A1 E1 A2 E2 A3 E3 B1 F1 B2 F2 B3 F3 C1 G1 C2 G2 C3 G3 D1 H1 D2 H2 D3 H3 ÌMNL-1595-QRG=Î