Philips DVDR3545V/37 Quick Start Manual

Online Go to www.philips.com/usasupport. Hotline Call 1-888-PHILIPS (1-888-744-5477) for our operators. Types of Media Used on This Recorder * DVD-RW/-R recorded in VR mode or non compatible recording format are not playable. * DVD-RW recorded in the mode other than +VR is not recordable on this unit unless you erase all contents in the disc (refer to page 87 in the User Manual). * DVD-R recorded in the mode other than +VR is not recordable on this unit. Type Playback Record DVD+RW DVD+R DVD-RW DVD-R VHS DVD+R Double Layer DVD-video CD-DA (audio CD) video CD Start Playback For DVD playback, press DVD fi rst. For VCR playback, press VCR fi rst. ❶ Insert a playable disc or a prerecorded cassette tape. ❷ Press PLAY to start playback. ❸ Press STOP to stop playback. To pause playback: Press PAUSE . To resume playback: Press PLAY . Start Recording For DVD recording, press DVD fi rst. For VCR recording, press VCR fi rst. ❶ Insert a recordable disc (make sure the disc is compatible with this unit) or a cassette tape. ❷ Press REC MODE to select a recording mode. ❸ Press SOURCE repeatedly to select the appropriate external input channel to record from. (e.g. TUNER, E1, E2 or E3(DV-IN)) z To record a TV programme: Press DTV/TV to select analog TV or digital TV, then use CH / or the Number buttons to select a desired channel to record. ❹ Press REC to start recording. Press REC again to make recording for 30 minutes. Press REC repeatedly to extend the recording time by 30 minutes for each press. ❺ Press STOP to stop the recording. You will need to finalize DVD+R, DVD-RW or DVD-R to play them back on other DVD players (refer to page 56 in the User Manual). Digital Video Disc Recorder & Video Cassette Recorder with Digital Tuner DVDR3545V/37 Quick Start Guide 1 Connections Basic Setup Enjoy What’s in the box? Digital Video Disc Recorder & Video Cassette Recorder with Digital Tuner Remote Control with Batteries (AAAx2) Enjoy RCA Audio / Video Cables RF Coaxial Cable User Manual User Manual Quick Start Guide 2 3 DVD RECORDER 4 HEAD HI-FI STEREO ONE TOUCH RECORDING • LONG PLAY DVD RECORDER / VCR DVDR 3545V STANDBY-ON REW F.FWD PLAY PLAY REC STOP/EJECT STOP REC CHANNEL SOURCE VCR DVD OPEN/CLOSE SV VIDEO L-AUDIO-R DV 2007 © Philips Consumer Electronics Company Marietta, GA 30006 0026 All rights reserved. Printed in China 12 NC 8239 300 56651 E9H90UD 1VMN23627 3 E9H90UD_QSG_EN.indd 1 E9H90UD_QSG_EN.indd 1 3/23/2007 4:12:45 PM 3/23/2007 4:12:45 PM

Your Philips recorder is now ready for use! Basic Connection A Before Connecting ❶ Disconnect the power cords of the devices from the AC outlet. ❷ Disconnect RF coaxial cable from antenna input jack of your TV. B Connecting Make the connections as illustrated below. HDMI OUT DVD DIGITAL AUDIO OUT AUDIO OUT S-VIDEO OUT IN COAXIAL L R L Y PB /CB PR /CR R L R OUT IN S-VIDEO IN --- AUDIO --- OUT IN --- VIDEO --- OUT COMPONENT VIDEO OUT DVD/VCR ANTENNA IN L Y PB /CB PR /CR R L R OUT IN S-VIDEO IN --- AUDIO --- OUT IN --- VIDEO --- OUT ONENT O OUT DVD/VCR ANTENNA AUDIO IN R L VIDEO IN ANT. IN rear of this unit rear of your TV 1 2 3 4 from antenna or cable TV RF coaxial cable to the AC outlet RF coaxial cable RCA audio cable RCA video cable ❶ Connect the RF coaxial cable from the TV antenna or cable TV to the ANTENNA IN jack of this unit. ❷ Use RF coaxial cable to connect ANTENNA OUT jack of this unit to the antenna input jack of your TV. AND ❸ Use RCA audio / video cables to connect the AUDIO / VIDEO OUT jacks of this unit to the audio / video input jacks of your TV. ❹ Plug in the power cords of the devices to the AC outlet. RF Modulator Connection If your TV has antenna in jack only, it is still possible to connect this unit to your TV by using a commercially available stereo audio / video RF modulator. In this case, follow the instructions below. A Before Connecting ❶ Disconnect the power cords of the devices from the AC outlet. ❷ Disconnect RF coaxial cable from antenna input jack of your TV. B Connecting Make the connections as illustrated below. AUDIO IN VIDEO IN L R ANT. IN ANT. OUT 4 3 HDMI OUT DVD DIGITAL AUDIO OUT AUDIO OUT S-VIDEO OUT IN COAXIAL L R L Y PB /CB PR /CR R L R OUT IN S-VIDEO IN --- AUDIO --- OUT IN --- VIDEO --- OUT COMPONENT VIDEO OUT DVD/VCR ANTENNA ANT. IN IN L Y PB /CB PR /CR R L R OUT IN S-VIDEO IN --- AUDIO --- OUT IN --- VIDEO --- OUT ONENT O OUT DVD/VCR ANTENNA AUDIO IN VIDEO IN L R ANT. IN ANT. OUT 4 3 rear of your TV From antenna or cable TV rear of your RF modulator rear of this unit RF coaxial cable RF coaxial cable RCA audio cable RCA video cable 1 2 3 4 5 ❶ Connect the RF coaxial cable from the TV antenna or cable TV to the ANTENNA IN jack of this unit. ❷ Use RF coaxial cable to connect ANTENNA OUT jack of this unit to the antenna input jack of your RF modulator. ❸ Use RF coaxial cable to connect antenna output jack of your RF modulator to the antenna input jack of your TV. ❹ Use RCA audio / video cables to connect the AUDIO / VIDEO OUT jacks of this unit to the audio / video input jacks of your RF modulator. ❺ Plug in the power cords of the devices to the AC outlet. * RF modulator is not supplied with this unit. You need to purchase it at your local store. Basic Setup 2 A Finding the Viewing Channel ❶ Press STANDBY-ON to turn on the unit. ❷ Turn on your TV. z If connected to your VCR, make sure it is switched off or in standby mode before proceeding. ❸ Press “2” on the TV’s remote control, then press channel down button repeatedly until you see the “Initial Setup” menu. This is the correct viewing channel (external input channel) for the recorder. OSD Language English Français Español * Refer to your TV’s user manual for details. B Initial Setting ❶ Use K / L to select your desired language, then press OK . ❷ Use K / L to select the type of broadcasting signal, then press OK . Channel Preset Make sure the antenna is connected to “ANTENNA IN” jack. Antenna Cable (Analog) Cable (Analog / Digital) The unit will start getting channels available in your area. Antenna: (When using antenna) The channels broadcasted in analog TV and digital TV are automatically scanned and memorized. Only the receivable channels in the area will be memorized. Cable (Analog): (When using basic cable) The channels broadcasted in analog CATV are automatically scanned and memorized. Cable (Analog / Digital): (When using basic cable) The channels broadcasted in analog CATV and digital CATV are automatically scanned and memorized. ❸ Press OK to activate “Clock Setting”. Clock Setting - - - / - - / - - - - ( - - - ) - - : - - - - ❹ Use { / B to select an item to set, and use K / L to select the contents to suit your preference, then press OK when you finish setting all the contents. Connection to a Cable / Satellite Box If you have a Cable / Satellite Box, follow the instructions below. A Before Connecting ❶ Disconnect the power cords of the devices from the AC outlet. ❷ Disconnect RF coaxial cable from antenna input jack of your TV. B Connecting Make the connections as illustrated below. AUDIO OUT L R VIDEO OUT S-VIDEO OUT RF OUT ANT. IN HDMI OUT DVD DIGITAL AUDIO OUT AUDIO OUT S-VIDEO OUT IN COAXIAL L R L Y PB /CB PR /CR R L R OUT IN S-VIDEO IN --- AUDIO --- OUT IN --- VIDEO --- OUT COMPONENT VIDEO OUT DVD/VCR ANTENNA RF OUT ANT. IN ANT. IN AUDIO IN R L VIDEO IN AUDIO OUT L R VIDEO OUT S-VIDEO OUT IN IN L Y PB /CB PR /CR R L R OUT IN S-VIDEO IN --- AUDIO --- OUT IN --- VIDEO --- OUT PONENT EO OUT DVD/VCR ANTENNA rear of this unit cable / satellite box rear of your TV 2 1 3 4 5 6 from cable TV / satellite RF coaxial cable RCA video cable RCA audio cable RF coaxial cable RCA video cable RCA audio cable ❶ Connect the RF coaxial cable from the cable TV / satellite to the antenna input jack of your cable / satellite box. ❷ Use RF coaxial cable to connect the RF output jack of your cable / satellite box to ANTENNA IN jack of this unit. ❸ Use RF coaxial cable to connect ANTENNA OUT jack of this unit to the antenna input jack of your TV. ❹ Use RCA audio / video cables to connect the audio / video output jacks of your cable / satellite box to the AUDIO / VIDEO IN jacks of this unit. ❺ Use RCA audio / video cables to connect the AUDIO / VIDEO OUT jacks of this unit to the audio / video input jacks of your TV. ❻ Plug in the power cords of the devices to the AC outlet. * Refer to the user manual for other connection methods. E9H90UD_QSG_EN.indd 2 E9H90UD_QSG_EN.indd 2 3/23/2007 4:13:01 PM 3/23/2007 4:13:01 PM