Super Circuits S2071 Manual 

Quick Guide S20712ch /S40714ch Enter the Main Page Step4 Install Internet Explorer Active X Controller Step5 Open a new Internet Explorer window. Start 1 Enter the new IP address and key in the username “root” and password “root”. Enter the IP address and login 2 ● When the login screen appears, key in root in the User Name and Password fields. Click OK. ● Enter the IP address that you have just set. You can enter the control screen when the username and password are confirmed. Enter the control screen 3 When the username and password are confirmed, a control setup screen pops up under the IE address bar. Click “Install ActiveX Control” to install the controls. Install ActiveX 1 ● Click Install ActiveX Control RMIM-01G06003 Ver:20 When ActiveX Control is installed successfully, you can see the camera image and interface. Camera operation and interface 3 ● Select the HTTP mode if the image is disabled. ● Click Install The ActiveX Control is named ActiveX Control. This software is well certified. You can use it without any doubts on its validity. The security warning screen aps. Click Install. 2 - Page 3 -  

2 3 4 5 6 7 8 RT RX + - DC 12V ALARM IN DC OUT RS485 ALARM OUT SD CARD LAN RESET 1. Make sure the analong camera is use the BNC connectors. 2. Please refer to user manual for more detailed explanation of the hardware installation. 3. Where no switch hub is available, you can search and set up the camera using the network peering approach. However, you may need a jumper and need to change the LAN configuration on your PC for this purpose. It is recommended to request a qualified engineer for the connection or execute the network peering referring to the user's manual . Connection diagram Step1 1 4 5 3 2 Step2 Camera settings Change the Internet Explorer settings Step3 ● Click Search to find the IP CAM on the LAN. Note: If this software cannot run successfully, check that it is not blocked by an anti-virus software or firewall. Execute the IP Finder.exe file from the supplied CD. Start 1 Search for the product from your LAN. The default IP setting 192.168.0.20 appears on the screen. Find the camera (Search) 2 When you find the camera, click it and the settings appear on the right side. You can change the settings for the new network environment as you need. Changing the IP address and related settings for the network environment 3 Submit data (Submit) 4 ● Click Submit to apply the new settings. Confirmation 5 ● Click Exit to quit, after all chages have been confirmed. Open the IE browser ↓ Tools ↓ Internet Options ↓ Security ↓ Custom Level Steps Note: This product supports IE 6.0 or above. ● Check that the security level is Level II. Bring Up Your IE browser. Start 1 Make sure that Level II, the commonly used default security level, is set for the security. Check 2 Make sure that Level II, the commonly used default security level, is set for the security. Select “medium” for security 3 Click OK to quit. OK 4 ● Enter the settings for the new network environment you need. - Page 1 - - Page 2 - VIDEO IN 1 2 3 MIC LINE OUT POWER 4 4 3 1 2 AUDIO IN • Video In • Speaker • Power • SD Card • PT Controller • Direct Current Power • Infrared Inductor • MIC • MIC Front Pannel Rear Pannel • Amplifier • HUB • WAN Internet • High dB alarm Alarm Output Connect the video server to the switch hub and analog camera VIDEO IN 1 2 3 MIC LINE OUT POWER 4 4 3 1 2 AUDIO IN Connect the Video source to Video IN. Note: Please connect RS-485 to the video server if your analog camera supports PTZ function. Power on the analog camera. Check the indicator lamp of POWER after power on the video server. Connect the video server and PC to the switch hub. Connection settings is completed. VIDEO IN 1 2 3 MIC LINE OUT POWER 4 4 3 1 2 AUDIO IN • The indicator lamp of POWER will be green when power on. Attention • You have to enter a new settings in the IP Netmask and Gateway fields and keep the settings in other fields unchanged. or    1 9 10 11 12 13 14 15 16 17 18 19 20 2 3 4 5 6 7 8 RT RX + - DC 12V ALARM IN DC OUT RS485 ALARM OUT SD CARD LAN RESET 1 9 10 11 12 13 14 15 16 17 18 19 20 2 3 4 5 6 7 8 RT RX + - DC 12V ALARM IN DC OUT RS485 ALARM OUT SD CARD LAN RESET