Visonic GB-502 PG2 Installation Instructions Manual

1 Introducing GB-502 PG2 Overview The GB-502 PG2 is a wireless PowerG Two-way acoustic glass-break detector designed to detect the breaking offramed glass mounted in an outside wall. This detector is wall/ceiling mountable and suitable for most types ofwindow/door glass: plate, tempered, laminated, wired, coated and sealed insulating glass. No adjustment is necessary during installation – the detector is fully pre-calibrated. A. Microphone B. Detection indicator Figure 1. General View The acoustic sensor ofthe GB-502 PG2 is omni-directional, providing fullcoverage. Coverage is measured from the sensor to the point on the glass farthest from the sensor. The sensor can be mounted as close as 1.5 m (5 ft) from the glass. Figure 2. Typical Range Measurement When mounted on opposite walls, on adjoining walls or on the ceiling, the range is 7.6 m (25 ft) for plate, tempered, laminated, wired, coated, and sealed insulating glass. The coverage range also depends on the angle between the detector and the glass – for a higher angle, the maximum range is reduced, see the following table for details. Angle (degrees) 0 30 45 60 75 90 Maximum range m (ft) 7.6 (25) 7 (23) 5.5 (18) 4 (13) 2.5 (8) 0 Figure 3. Angle between detector and window GB-502 PG2 Wireless PowerG Two-Way Acoustic Glass- break Detector Installation Instructions

2 PowerG Transmitter Upon alarm (glass break detection), a digitalmessage is transmitted, composed ofthe PowerG ID followed by various status and message-type mark- ers. Alarm and other data are thus forwarded to the wireless alarm controlpanel. The GB-502 PG2 is protected by a back tamper switch that is activated when the cover is removed or when the base is forcibly detached from the wall. In a tamper situation, a message is transmitted with the “tamper alert” marker ON. Aperiodic supervision message, distinguished by a specific marker, is transmitted automatically. The wireless controlpanelis thus informed, at regular intervals, ofthe sensor’s active participation in the system. Abicolor LED lights whenever events are reported. The LED does not light while a supervision message is being transmitted. Installation Optimizing Detection and Avoiding False Alarms For best detection, avoid installing in: l Rooms with lined, insulating, or sound deadening drapes. l Rooms with closed wooden window shutters inside. For best false alarm immunity: l Avoid 24-hour loop applications (perimeter loop OK). l Don't use where white noise, such as air compressor noise, is present (a blast ofcompressed air may cause a false alarm) l Avoid rooms smaller than 3 x 3 m (10 x 10 ft) and rooms with multiple noise sources such as smallkitchens, glass booths noisy areas, garages, smallbathrooms, etc. Areas to avoid: l Glass airlocks and glass vestibule areas l Noisy kitchens l Residentialcar garages l Smallutility rooms l Stairwells l Smallbathrooms l For glass break protection in such applications, use shock sensors on the windows or window frames. Do Not Install In Humid Rooms The Wireless GB-502 PG2 is not hermetically sealed. Excess moisture on the circuit board can eventually cause a short and a false alarm. Avoid 24-Hour Loop Applications The GB-502 PG2 is recommended for perimeter loops and is designed to function in an occupied area. In 24-hour loop applications, where the sensor is armed allday and allnight, the false alarm prevention technology willbe pushed to its limit. Some sounds can duplicate the glass break pattern the acoustic sensor detects. Installthe GB-502 PG2 on a perimeter loop which is armed whenever the door and window contacts are armed. NOTE: GB-502 PG2 shallbe installed in accordance with the Standard for Installation and Classification ofBurglar and Holdup Alarm Systems, UL 681 Protecting Occupied Areas The false alarm immunity is best in rooms with only moderate noise. For 24-hour occupied area protection, use shock sensors. Proper Testing The GB-502 PG2 is designed to detect the breaking offramed glass mounted in an outside wall. Testing the sensor with unframed glass, broken bottles, etc., may not trip the sensor. The sensor typically does not trip to glass breaking in the middle ofthe room. No burglar breaks glass in the middle ofa room, so such “breaks” are false alarms. NOTE: GB-502 PG2 may not consistently detect cracks in glass, or bullets which break through the glass. Glass-break sensors should always be backed up by interior protection. For best false alarm immunity the sensor should be located at least 1.2 m (4 ft) away from noise sources (televisions, speakers, sinks, doors, etc.). The sensor must always be in direct line ofsight ofallprotected windows. It cannot consistently detect glass breaking around corners, in other rooms, etc. Front or back, up or down orientation is not necessary. Sound Travel Considerations Since the sound ofbreaking glass travels directionally out from the broken window, the best location for mounting the sensor is on the opposite wall- assuming the glass to be protected is within the sensor's range and line ofsight. When mounted on the opposite wall, the detector should be mounted at least 1.8 m (6 ft) offthe floor, but not less than 30 cm (12”) from the ceiling. The ceiling also has good sensor locations. Aceiling mounted sensor will have better detection ifpositioned 2 - 4 m (6 - 12 ft) away from the protected glass into the room. Corner and adjoining (side) wallmounting is per- mitted but range versus angle limitations should be taken into consideration.

3 There should be no obstructions between the detector and the protected glass. Curtains, blinds and sound absorbing materials in the protected room may reduce the effective range. As with all glass-break sensors, mounting on the same wall as the protected glass is less effective and strictly not recommended - optimum detection is partially dependent on sound reflection off the opposite wall. Inserting the Battery 1. Press in the snap and separate the cover from the base. A. Snap Figure .4 Opening the Unit 2. Get to know the items indicated in Figure 5 - they are allrelevant to the steps you willhave to take in the course ofinstallation. A. Battery B. Enroll button C. Tamper contact Figure 5. Inside View 3. Insert the battery into the battery clips. Observe Polarity! Caution! Risk of explosion if battery is replaced by an incorrect type. Dispose of used battery according to manufacturer's instructions. A. Negative terminal B. Positive terminal Figure 6. Battery Insertion

4 Mounting the Device For mounting the device with a bracket, refer to the BR-1, BR-2 or BR-3 Installation Instructions. Note that you can also mount the device without a BR bracket. 1. Fasten the breakaway segment to the wall. A. Mounting holes B. Break-away base segment C. Fastening screw Figure 7. GB-502 PG2 Internal View Attention! The GB-502 PG2 has a back tamper switch under the PCB. As long as the PCB is seated firmly within the base, the switch is pressed against a specialbreak-away base segment that is loosely connected to the base. Be sure to fasten, using screw C, the break-away segment to the wall. Ifthe detector unit is forcibly removed from the wall, this segment willbreak away from the base, causing the tamper switch to open! 2. Put back the cover on the base and secure with screw. Figure 8. Closing the Cover Enrollment of the Device Refer to the PowerMaster panel's Installer Guide and follow this procedure under the "02:ZONES/DEVICES" option ofthe Installer Menu. 1. Enter the Installer menu and select “02:ZONES/DEVICES”. 02.ZONES/DEVICES ð 2. Select "ADD NEW DEVICE". Option. ADD NEW DEVICES ð 3. Enrollthe device or Enter the device ID. ENROLL NOW or ENTR ID:XXX-XXXXð 4. Select the desired Zone Number. Z04:Glass Break ID No. 160-XXXX ð(with panels PowerG V.19.1 & lower) ID No. 161-XXXX ð(with panels PowerG V.19.2 & higher) 5. Configure Location & Zone Type Parameters. Z06.LOCATION Z06.ZONE TYPE ð means scrollwwand select OK.

5 Local Diagnostics Test Procedure Before testing, separate the base from the cover. The following table indicates the received signalstrength. LED response Reception Green LED blinks Strong Orange LED blinks Good RED LED blinks Poor No blinks No communication IMPORTANT! Reliable reception must be assured. Therefore, "poor" signalstrength is not acceptable. Ifyou receive a "poor" signalfrom the device, re-locate it and re-test untila "good" or "strong" signalstrength is received. Note: For detailed Diagnostics Test instructions refer to the controlpanelInstaller Guide. Testing Procedures Switching the Sensor to the Test Mode After power-up or closing the cover, the detector willautomatically enter a 15 minute test mode. For remote switching ofthe detector to test mode (via User or Installer Code), refer to the PowerMaster Installer Guide, Chapter 6, Periodic Test. Testing the Sensor A. Basic Test Test the detector's low frequency (FLEX) respons by thumping the protected glass with a cushioned object. The green LED willlight for 2 seconds. Repeat the test ifnecessary. B. Extended Glassbreak Simulation Test (optional) This optionaltest activates the detector with Flex and audio sounds, that simulate the glass breaking sound ofa window. Take care not to shatter the glass during testing. Procedure To test complete the following steps: 1. Switch the detector to Test Mode (see "Switching the Sensor to the Test Mode" above). 2. Generate a flex signaland simulate a glass breaking sound by using one ofthe following methods: l Simulator in manualmode Hold the simulator close to the protected glass. Thump the glass and immediately start the simulator manually to create the sound ofbreak- ing glass. Examples ofsuch simulators are AFT-100 or 5709C. l Simulator with automatic activation Hold the simulator close to the protected glass. Thump the glass, the simulator creates the sound ofbreaking glass automatically. Examples ofautomatic simulators using flex signals are FG-700/ FG-701 or GT-2. l Hand clap Thump the glass and immediately clap hands firmly three times. This method is best used in relatively smallrooms with a maximum distance up to 5 or 6 m (16 ft or 20 ft). Note The instructions for some simulators instruct you to switch the glass break detector to Test mode by sounding a specialsignal. The GB-502 PG2 detector has an inbuilt Test mode therefore it is not necessary to use that switch. Use a glass pane with dimensions ofat least 0.5 x 0.5 m (1.5 x 1.5 ft) to assure success ofthe simulator test. Always aim the simulator at the detector being tested. 3. The detector willalarm, the red LED lights for 2 seconds. 4. Repeat the test ifnecessary. IMPORTANT! Room acoustics can artificially extend the range ofa glass-break sensor. The specified range ofthe GB-502 PG2 has been established for worst-case conditions. While the sensor is likely to function at additionalrange, it may miss a “minimum output” break, or room acoustics may be changed at some future time, restoring sensor coverage back to the normalrange of6 m (20 ft). Do not exceed the rated range ofthe sensor, regardless ofwhat the tester shows.

6 Installation Tips l The GB-502 PG2 detects the shattering offramed glass mounted on an outside wall. Testing the sensor with unframed glass, broken bottles, etc. might not trip the sensor. False alarms such as glass breaking in the middle ofa room willnot activate the sensor. l False alarms are most likely to occur when installed on a 24-hour loop, in glass airlocks, and glass vestibule areas. Similarly, when mounted above sinks, residentialgarages, and in other smallacoustic live rooms, false alarms can be generated. In rooms where multiple sounds can reflect and eventually duplicate the glass break frequency pattern, use shock sensors. l Installing the GB-502 PG2 on 24-hour loops willincrease false alarms. Installthe GB-502 PG2 on a perimeter loop, which is armed whenever the door and window contacts are armed. For occupied areas, GB-502 PG2 false alarm immunity is best in rooms with only moderate noise levels. l GB-502 PG2 detects the shattering ofglass. Like allglass-break sensors, the detector might not consistently detect cracks in glass, or bullets that break through or break out the glass. Glass-break sensors should always be backed up by interior protection. Event Indications LED Indications and Events LED Response Description Red LED blinks Stabilization (warm-up 8 sec) Red LED ON 0.2 sec. Tamper open / close Red LED ON 2 sec. Glass break alarm Green LED ON 2 sec. Low frequency detection – Test mode Green and red LED blink alternately (0.2 sec Green, 0.2 sec Red, 0.4 sec OFF) Self-test failure – Test mode Green and red LED blink alternately slowly (0.2 sec Green, 0.2 sec Red, 30 sec OFF) Self-test failure – Normalmode Compliance With Standards The GB-502 PG2 complies with the following standards: Europe: EN 300220, EN 301489, EN50130-4, EN60950, EN50130-5, EN 50131-2-7-1, EN 50131-1 Grade 2 Class II This device complies with the essentialrequirements and provisions ofDirective 1999/5/ECofthe European Parliament and ofthe Councilof9 March 1999 on radio and telecommunications terminal equipment. USA: CFR 47 Part 15 (FCC) Canada: RSS 210 USA: UL639 Canada: ULC-S306 WARNING! Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC Rules and with Industry Canada license-exempt RSS standard(s). Operation is sub- ject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any inter- ference received, including interference that may cause undesired operation. Le present appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisee aux deux conditions suivantes :(1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioelectrique subi, meme si le brouillage est susceptible d'en compromettre le fonctionnement. W.E.E.E. Product Recycling Declaration For information regarding the recycling of this product you must contact the company from which you originally purchased it. If you are discarding this product and not returning it for repair then you must ensure that it is returned as identified by your supplier. This product is not to be thrown away with everyday waste. Directive 2002/96/EC Waste Electrical and Electronic Equipment.

7 The Power G peripheraldevices have two- way communication functionality, providing additionalbenefits as described in the technicalbrochure. This functionality has not been tested to comply with the respective technicalrequirements and should therefore be considered outside the scope ofthe product’s certification. Specifications POWERG TRANSMITTER Frequency Band (MHz) Europe and rest ofworld: 433-434, 868-869 USA: 912-919 Communication Protocol PowerG Supervision Signaling at 4-min. intervals Tamper Alert Reported when a tamper event occurs POWER SUPPLY Power Supply 3 V Lithium CR-123 type battery, Panasonic, Sanyo or GP only. Nominal Battery Capacity 1.45 Ah Battery Life Expectancy 5 years (for typicaluse) Battery Supervision Automatic transmission ofbattery condition data as part ofperiodic status report Low Battery Threshold 2.6 V ENVIRONMENTAL RF Immunity 20 V/m up to 1000 MHz, 10 V/m up to 2700 MHz Operating Temperature -10°Cto 50°C(14°F to 120°F) indoors Storage Temperature -20°Cto 60°C(-4°F to 140°F) Humidity 5 %to 95 %with no condensation. ACOUSTIC SENSOR Microphone Omni-directional Maximum Detection Range 7.6 m (25 ft) ifglass size is minimum 40 x 40 cm (15 ¾” x 15 ¾”). 6 m (20 ft) ifglass size is 30 x 30 cm (12” x 12”) to 40 x 40 cm (15 ¾” x 15 ¾”) Glass Types Plate, tempered, wired, laminated , covered, and sealed insulated. Minimum Glass Size 30 x 30 cm (12” x 12”) Glass Thickness Plate: 3.2 to 6.4 mm (1/8” to ¼”) Tempered: 3.2 to 6.4 mm (1/8” to ¼”) Wired: 6.4 mm (¼”) Coated: 3.2 to 6.4 mm (1/8” to ¼”) Laminated: 6.4 mm (¼”) Sealed Insulating: 3.2 to 6.4 mm (1/8” to ¼”) Note: Laminated and Sealed Insulating glass types are protected only ifboth plates ofthe unit are broken. Room Size Not larger than 12 x 12 m (36 x 36 ft); Not smaller than 3 x 3 m (10 x 10 ft). Min. Distance from Glass 1.5 m (5 ft) ACCESSORIES Brackets BR-1: Surface mounted swivelbracket, adjustable 30° down and 45° left/45° right. BR-2: BR-1 with a corner adapter BR-3: BR-1 with a ceiling adapter PHYSICAL Dimensions 88 x 62 x 30 mm (3.5 x 2.4 x 1.2 in.). Weight (not including battery) 74 g (2.6 oz) Housing Material and Color Flame retardant PC-ABS, white

8 WARRANTY Visonic Limited (the “Manufacturer") warrants this product only (the "Product") to the originalpurchaser only (the “Purchaser”) against defective work- manship and materials under normaluse ofthe Product for a period oftwelve (12) months from the date ofshipment by the Manufacturer. This Warranty is absolutely conditionalupon the Product having been properly installed, maintained and operated under conditions ofnormaluse in accordance with the Manufacturers recommended installation and operation instructions. Products which have become defective for any other reason, according to the Manufacturers discretion, such as improper installation, failure to follow recommended installation and operationalinstruc- tions, neglect, willfuldamage, misuse or vandalism, accidentaldamage, alteration or tampering, or repair by anyone other than the manufacturer, are not covered by this Warranty. There is absolutely no warranty on software, and allsoftware products are sold as a user license under the terms ofthe software license agreement included with such Product." The Manufacturer does not represent that this Product may not be compromised and/or circumvented or that the Product willprevent any death and/or personalinjury and/or damage to property resulting from burglary, robbery, fire or otherwise, or that the Product willin allcases provide adequate warning or protection. The Product, properly installed and maintained, only reduces the risk ofsuch events without warning and it is not a guarantee or insurance that such events willnot occur. Conditions to Void Warranty: This warranty applies only to defects in parts and workmanship relating to normaluse ofthe Products. It does not cover: * damage incurred in shipping or handling; * damage caused by disaster such as fire, flood, wind, earthquake or lightning; * damage due to causes beyond the controlofthe Seller such as excessive voltage, mechanicalshock or water damage; * damage caused by unauthorized attachment, alterations, modifications or foreign objects being used with or in conjunction with the Products; * damage caused by peripherals (unless such peripherals were supplied by the Seller; * defects caused by failure to provide a suitable installation environment for the products; * damage caused by use ofthe Products for purposes other than those for which they were designed; * damage from improper maintenance; * damage arising out ofany other abuse, mishandling or improper application ofthe Products. Items Not Covered by Warranty: In addition to the items which void the Warranty, the following items shallnot be covered by Warranty: (i) freight cost to the repair centre; (ii) customs fees, taxes, or VAT that may be due; (iii) Products which are not identified with the Seller's product labeland lot number or serialnumber; (iv) Products disassembled or repaired in such a manner as to adversely affect performance or prevent adequate inspection or testing to verify any warranty claim. Access cards or tags returned for replacement under warranty willbe credited or replaced at the Seller's option. THIS WARRANTY IS EXCLUSIVE AND EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, OBLIGATIONS OR LIABILITIES, WHETHER WRITTEN, ORAL, EXPRESS OR IMPLIED, INCLUDING ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR APARTICULAR PURPOSE, OR OTHERWISE. IN NO CASE SHALL THE MANUFACTURER BE LIABLE TO ANYONE FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES FOR BREACH OF THIS WARRANTY OR ANY OTHER WARRANTIES WHATSOEVER, AS AFORESAID. THE MANUFACTURER SHALL IN NO EVENT BE LIABLE FOR ANY SPECIAL, INDIRECT, INCIDENTAL, CONSEQUENTIAL OR PUNITIVE DAMAGES OR FOR LOSS, DAMAGE, OR EXPENSE, INCLUDING LOSS OF USE, PROFITS, REVENUE, OR GOODWILL, DIRECTLY OR INDIRECTLY ARISING FROM PURCHASER’S USE OR INABILITY TO USE THE PRODUCT, OR FOR LOSS OR DESTRUCTION OF OTHER PROPERTY OR FROM ANY OTHER CAUSE, EVEN IF MANUFACTURER HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. THE MANUFACTURER SHALL HAVE NO LIABILITY FOR ANY DEATH, PERSONAL AND/OR BODILY INJURY AND/OR DAMAGE TO PROPERTY OR OTHER LOSS WHETHER DIRECT, INDIRECT, INCIDENTAL, CONSEQUENTIAL OR OTHERWISE, BASED ON ACLAIM THAT THE PRODUCT FAILED TO FUNCTION. HOWEVER, IF THE MANUFACTURER IS HELD LIABLE, WHETHER DIRECTLY OR INDIRECTLY, FOR ANY LOSS OR DAMAGE ARISING UNDER THIS LIMITED WARRANTY, THE MANUFACTURER'S MAXIMUM LIABILITY (IF ANY) SHALL NOT IN ANY CASE EXCEED THE PURCHASE PRICE OF THE PRODUCT INVOLVED, WHICH SHALL BE FIXED AS LIQUIDATED DAMAGES AND NOT AS APENALTY, AND SHALL BE THE COMPLETE AND EXCLUSIVE REMEDY AGAINST THE MANUFACTURER. SOME JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THESE LIMITATIONS MAY NOT APPLY UNDER CERTAIN CIRCUMSTANCES. When accepting the delivery ofthe Product, the Purchaser agrees to the said conditions ofsale and warranty and he recognizes having been informed of. The Manufacturer shallbe under no liability whatsoever arising out ofthe corruption and/or malfunctioning ofany telecommunication or electronic equipment or any programs. The Manufacturers obligations under this Warranty are limited solely to repair and/or replace at the Manufacturer’s discretion any Product or part thereofthat may prove defective. Any repair and/or replacement shallnot extend the originalWarranty period. The Manufacturer shallnot be respons- ible for dismantling and/or reinstallation costs. To exercise this Warranty the Product must be returned to the Manufacturer freight pre-paid and insured. Allfreight and insurance costs are the responsibility ofthe Purchaser and are not included in this Warranty. For sales in Israel only: The Purchaser shallcomply with the provisions ofthe IsraeliConsumer Protection Law – 1981("Consumer Protection Law") related regulations, includ- ing the IsraeliConsumer Protection Regulations (Warranty Sticker), 5772-2012) ("Regulations"), including, without limitation (i) providing its cus- tomers with at least the minimum warranty required by the Consumer Protection Law, and (ii) ensuring that a warranty certificate and a warranty sticker (as defined in the Regulations) ("Warranty Sticker") shallbe attached to any sold Products and the date ofthe sale ofthe Product to the con- sumer or the end-user shallbe added in a readable manner on the Warranty Sticker.

9 In no event shallthe Purchser’s compliance with the Consumer Protection Law and Regulations expand any ofthe Manufacturer's warranty obligations under this warranty, and the Purchaser shallbe responsible for any warranty that it provides with respect to the Products which exceeds or is different from this warranty. This warranty shallnot be modified, varied or extended, and the Manufacturer does not authorize any person to act on its behalfin the modification, variation or extension ofthis warranty. This warranty shallapply to the Product only. Allproducts, accessories or attachments ofothers used in con- junction with the Product, including batteries, shallbe covered solely by their own warranty, ifany. The Manufacturer shallnot be liable for any damage or loss whatsoever, whether directly, indirectly, incidentally, consequentially or otherwise, caused by the malfunction ofthe Product due to products, accessories, or attachments ofothers, including batteries, used in conjunction with the Products. This Warranty is exclusive to the originalPurchaser and is not assignable. This Warranty is in addition to and does not affect your legalrights. Any provision in this warranty which is contrary to the Law in the state or country were the Product is supplied shallnot apply. Governing Law: This disclaimer ofwarranties and limited warranty are governed by the domestic laws ofIsrael. Warning The user must follow the Manufacturer’s installation and operationalinstructions including testing the Product and its whole system at least once a week and to take allnecessary precautions for his/her safety and the protection ofhis/her property. * In case ofa conflict, contradiction or interpretation between the English version ofthe warranty and other versions, the English version shallprevail. 7/15 End-User License Agreement IMPORTANT - READ THIS END- USER LICENSE AGREEMENT ("EULA") CAREFULLY BEFORE OPENING THE DISK PACKAGE, DOWNLOADING THE SOFTWARE OR INSTALLING, COPYING OR OTHERWISE USING THE SOFTWARE. THIS EULA IS A LEGAL AGREEMENT BETWEEN YOU AND VISONIC LTD. (“TYCO”) AND GOVERNS YOUR USE OF THE SOFTWARE ACCOMPANYING THIS EULA, WHICH SOFTWARE INCLUDES COMPUTER SOFTWARE AND MAY INCLUDE MEDIA, PRINTED MATERIALS, AND "ON-LINE" OR ELECTRONIC DOCUMENTATION (COLLECTIVELY, THE "SOFTWARE"). BY BREAKING THE SEAL ON THIS PACKAGE, DOWNLOADING THE SOFTWARE OR INSTALLING, COPYING OR OTHERWISE USING THE SOFTWARE, YOU AGREE TO BE BOUND BY THE TERMS OF THIS EULA. IF YOU DO NOT AGREE TO ALL OF THE TERMS AND CONDITIONS OF THIS EULA, DO NOT OPEN, DOWNLOAD, INSTALL, COPY OR OTHERWISE USE THE SOFTWARE. 1. SCOPE OF LICENSE. The Software may include computer code, program files and any associated media, hardware or software keys, printed materialand electronic documentation. The Software may be provided to you pre-installed on a storage device (the media) as part ofa computer sys- tem or other hardware or device (“System”). The Software is protected by copyright laws and international copyright treaties, as wellas other intel- lectualproperty laws and treaties. Alltitle and intellectualproperty rights in and to the Software (including but not limited to any images, photographs, and text incorporated into the Software), the accompanying printed materials, and any copies ofthe Software, are owned by Tyco and/or its suppliers. The Software is licensed, not sold. Allrights not expressly granted under this EULAare reserved by Tyco and its suppliers. 2. GRANT OF LICENSE. This EULAgrants you the following rights on a non-exclusive basis: a. General. This EULApermits you to use the Software for which you have purchased this EULA. Once you have purchased licenses for the number ofcopies ofthe Software that you require, you may use the Software and accompanying material provided that you install and use no more than the licensed number ofcopies at one time. The Software is only licensed for use with specified Licensor-supplied Systems. Ifthe Software is pro- tected by a software or hardware key or other device, the Software may be used on any computer on which the key is installed. Ifthe key locks the Software to a particular System, the Software may only be used on that System. b. Locally Stored Components. The Software may include a software code component that may be stored and operated locally on one or more devices. Once you have paid the required license fees for these devices (as determined by Tyco in its sole discretion), you may install and/or use one copy ofsuch component ofthe Software on each ofthe devices as licensed by Tyco. You may then use, access, display, run or otherwise inter- act with ("use") such component ofthe Software in connection with operating the device on which it is installed solely in the manner set forth in any accompanying documentation or, in the absence ofsuch, solely in the manner contemplated by the nature ofthe Software. c. Remotely Stored Components. The Software may also include a software code component for operating one or more devices remotely.  You may installand/or use one copy ofsuch component ofthe Software on a remote storage device on an internalnetwork with allof the devices and may operate such component with each device over the internalnetwork solely in the manner set forth in any accompanying documentation or, in the absence ofsuch, solely in the manner contemplated by the nature ofthe Software; provided however, you must stillacquire the required num- ber oflicenses for each ofthe devices with which such component is to be operated. d. Embedded Software/Firmware. The Software may also include a software code component that is resident in a device as provided by Tyco for operating that device. You may use such component of the Software solely in connection with the use ofthat device, but may not retrieve, copy or otherwise transfer that software component to any other media or device without Tyco's express prior written authorization. e. Backup Copy. You may make a back-up copy ofthe Software (other than embedded software) solely for archivalpurposes, which copy may only be used to replace a component ofthe Software for which you have current valid license. Except as expressly provided in this EULA, you may not otherwise make copies ofthe Software, including the printed materials. 3. OTHER RIGHTS AND LIMITATIONS. Your use of the Software is subject to the following additional limitations.  Failure to comply with any of these restrictions willresult in automatic termination ofthis EULAand willmake available to Tyco other legalremedies.

10 a. Limitations on Reverse Engineering and Derivative Works. You may not reverse engineer, decompile, or disassemble the Software, and any attempt to do so shallimmediately terminate this EULA- except and only to the extent that such activity may be expressly permitted by applicable law notwithstanding this limitation. You may not make any changes or modifications to any portion ofthe Software, or create any derivative works, without the written permission of an officer of Tyco (except as provided in Section 3(f) of this EULAwith respect to “open source” software). You may not remove any proprietary notices, marks or labels from the Software. You shall institute reasonable measures to ensure compliance with the terms and conditions ofthis EULAby your personneland agents. b. Copyright Notices. You must maintain allcopyright notices on allcopies ofthe Software. c. Transfer. You may only transfer your rights under this EULA(i) as part ofa permanent sale or transfer ofallofthe devices for which the Software is licensed as applicable; (ii) ifyou transfer all of the Software (including all component parts, the media and printed materials, any upgrades and this EULA); (iii) ifyou do not retain any copies of any portion ofthe Software; (iv) ifthe recipient agrees to the terms ofthis EULA; and (v) ifthe Soft- ware is an upgrade, such transfer must also include allprior versions ofthe Software. You agree that failure to meet allofthese conditions renders such transfer nulland void. d. Termination. Without prejudice to any other rights, Tyco may terminate this EULA ifyou fail to comply with the terms and conditions herein. In such event, you must immediately destroy allcopies of the Software and allof its component parts.  To the extent the Software is embedded in hardware or firmware, you will provide prompt access to Tyco or its representative to remove or lock Software features or functionality as Tyco determines. e. Subsequent EULA. Tyco may also supersede this EULAwith a subsequent EULApursuant to providing you with any future component, release, upgrade or other modification or addition to the Software.  Similarly, to the extent that the terms of this EULAconflict with any prior EULAor other agreement between you and Tyco regarding the Software, the terms ofthis EULAshallprevail. f. Incorporation of “Open Source” and other Third Party Software. Portions of the Software may be subject to certain third party license agree- ments governing the use, copying, modification, redistribution and warranty ofthose portions ofthe Software, including what is commonly known as “open source” software.  A copy of each applicable third party license can be found in the file README.TXT or other documentation accom- panying the Software.  Such open source software is not subject to any warranty and indemnity set forth in this EULA.   By using the Software you are also agreeing to be bound to the terms of such third party licenses.  If provided for in the applicable third party license, you have a right to receive source code for such software for use and distribution in any program that you create, so long as you in turn agree to be bound to the terms ofthe applicable third party license, and your programs are distributed under the terms ofthat license.  Acopy ofsuch source code may be obtained free ofcharge by contacting your Tyco representative. g. Trademarks. This EULAdoes not grant you any rights in connection with any trademarks or service marks ofTyco, its affiliates or its suppliers. h. Rental. You may not sublicense, rent, lease or lend the Software. You may not make it available to others or post it on a server or web site or oth- erwise distribute it. i. Software Keys. The hardware/software key, where applicable, is your proof oflicense to exercise the rights granted herein and must be retained by you. Lost or stolen keys willnot be replaced. j. Demonstration and Evaluation Copies. Ademonstration or evaluation copy of the Software is covered by this EULA; provided that the licenses contained herein shallexpire at the end ofthe demonstration or evaluation period. k. Registration ofSoftware. The Software may require registration with Tyco prior to use.  If you do not register the Software, this EULA is auto- matically terminated and you may not use the Software. l. Additional Restrictions. The Software may be subject to additionalrestrictions and conditions on use as specified in the documentation accom- panying such Software, which additionalrestrictions and conditions are hereby incorporated into and made a part ofthis EULA. m. Upgrades and Updates. To the extent Tyco makes them available, Software upgrades and updates may only be used to replace allor part of the original Software that you are licensed to use.  Software upgrades and updates do not increase the number ofcopies licensed to you.  If the Software is an upgrade ofa component of a package ofSoftware programs that you licensed as a single product, the Software may be used and transferred only as part of that single product package and may not be separated for use on more than one computer or System.  Software upgrades and updates downloaded free of charge via a Tyco authorized World Wide Web or FTP  site may be used to upgrade multiple Systems provided that you are licensed to use the originalSoftware on those Systems. n. Tools and Utilities. Software distributed via a Tyco-authorized World Wide Web or FTP site (or similar Tyco-authorized distribution means) as a toolor utility may be copied and installed without limitation provided that the Software is not distributed or sold and the Software is only used for the intended purpose ofthe toolor utility and in conjunction with Tyco products. Allother terms and conditions ofthis EULAcontinue to apply. 4. EXPORT RESTRICTIONS. You agree that you will not export, re-export or transfer any portion of the Software, or any direct product thereof (the foregoing collectively referred to as the "Restricted Components"), to IRAN, NORTH KOREA, SYRIA, CUBA and SUDAN,  including any entities or persons in those countries, either directly or indirectly (“Tyco’s Position”).  You also agree that you willnot export, re-export or transfer the Restricted Components to any other countries except in fullcompliance with allapplicable governmentalrequirements, including but not limited to applicable eco- nomic sanctions and constraints administered by any Israeligovernmentalauthority, including, but not limited to the IsraeliMinistry ofDefense, by any applicable treaty, applicable export control measures administered by Israel , U.S. Treasury Department and applicable export control measures administered by the U.S. Department of Commerce and U.S. Department of State, any other U.S. government agencies, and measures administered by the European Union or the government agencies of any other countries. Any violation by you ofthe applicable laws or regulations ofthe U.S. or any

11 other government, or where you breach Tyco’s Position notwithstanding whether or not this is contrary to any aforementioned applicable laws or reg- ulations, willresult in automatic termination ofthis EULA. 5. U.S. GOVERNMENT RESTRICTED RIGHTS. The Software is Commercial Computer Software provided with "restricted rights" under Federal Acquisition Regulations and agency supplements to them. Any use, duplication or disclosure by the U.S. Government is subject to restrictions as set forth in subparagraph (c)(1)(ii) ofthe Rights in TechnicalData and Computer Software clause at DFAR 255.227-7013 et. seq. or 252.211-7015, or sub- paragraphs (a) through (d) of the CommercialComputer Software Restricted Rights at FAR 52.227-19, as applicable, or similar clauses in the NASA FAR Supplement. Contractor/manufacturer is Visonic Ltd., 24 HabarzelSt., Tel-Aviv, Israel69710. 6. LIMITATION OF LIABILITY & EXCLUSION OF DAMAGES. a. LIMITATION OF LIABILITY. IN NO EVENT WILL TYCO’S AGGREGATE LIABILITY (INCLUDING, BUT NOT LIMITED TO, LIABILITY FOR NEGLIGENCE, STRICT LIABILITY, BREACH OF CONTRACT, MISREPRESENTATION AND OTHER CONTRACT OR TORT CLAIMS) ARISING FROM OR RELATED TO THIS EULA, OR THE USE OF THE SOFTWARE, EXCEED THE AMOUNT OF FEES YOU PAID TO TYCO OR ITS RESELLER FOR THE SOFTWARE THAT GIVES RISE TO SUCH LIABILITY. BECAUSE AND TO THE EXTENT THAT SOME JURISDICTIONS DO NOT ALLOW THE EXCLUSIONS OR LIMITATIONS OF LIABILITY ABOVE, THESE MAY NOT APPLY TO YOU. b. EXCLUSION OF OTHER DAMAGES. UNDER NO CIRCUMSTANCES SHALL TYCO OR ANY OF ITS RESELLERS OR LICENSORS BE LIABLE FOR ANY OF THE FOLLOWING: (I) THIRD PARTY CLAIMS; (II) LOSS OR DAMAGE TO ANY SYSTEMS, RECORDS OR DATA, OR LIABILITIES RELATED TO A VIOLATION OF AN INDIVIDUAL'S PRIVACY RIGHTS; OR (III) INDIRECT, INCIDENTAL, SPECIAL, CONSEQUENTIAL, PUNITIVE, RELIANCE, OR COVER DAMAGES (INCLUDING WITHOUT LIMITATION, LOSS OF PROFITS, BUSINESS INTERRUPTION, LOSS OF DATAOR BUSINESS INFORMATION AND LOST SAVINGS), IN EACH CASE EVEN IF TYCO HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. YOU ARE SOLELY RESPONSIBLE AND LIABLE FOR VERIFYING THE SECURITY, ACCURACY AND ADEQUACY OF ANY OUTPUT FROM THE SOFTWARE, AND FOR ANY RELIANCE THEREON. SOME JURISDICTIONS DO NOT ALLOW THE EXCLUSION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, OR THE LIMITATION ON HOW LONG AN IMPLIED WARRANTY LASTS, SO SOME OF THE ABOVE LIMITATIONS MAY APPLY TO YOU ONLY TO THE EXTENT PERMITTED BY THOSE LAWS. GENERAL. If any provision of this EULA is found to be unlawful, void, or for any reason unenforceable, then that provision shall be severed from this EULA and shall not affect the validity and enforceability of the remaining provisions. You should retain proof of the license fee paid, including model num- ber, serial number and date of payment, and present such proof of payment when seeking service or assistance covered by the warranty set forth in this EULA. This EULA is governed by the laws of Israel, without giving effect to any choice or conflict of law provision or rule that would cause the application of the laws of any jurisdiction other than Israel. Each of the Parties submits to the exclusive jurisdiction of any court sitting in Tel Aviv, Israel for purposes of resolving any and all disputes arising under or related to these terms and conditions. The parties specifically exclude the application of the provisions of the United Nations Convention on Contracts for the International Sale of Goods. Email: [email protected] Internet: www.visonic.com © VISONICLTD. 2015 GB-502 PG2 D-306217 Rev. 1 01/16