Vision Hi-Tech VC59SFHD2 Quick Installation Manual

2 Megapixel FULL HD Box Camera ◆ Uncompressed high quality Full HD video with full frame rate Full HD video transmission up to 100M 1920X1080 60p/50p/25p/30p, 1280X720 60p/50p/30p/25p Enhanced WDR performance Quick and easy OSD control Diverse Video output for diverse applications (HD-SDI & Composite) 2D/3D DNR (Digital Noise Reduction) Defog function Dynamic digital zoom and PIP Pelco-C support (CVBS output with optional controller) Privacy Masking (8 Polygon Area) Supports 15 Languages RS-485 Interface for external control of OSD (Using controllers, etc.) 12VDC or 12VDC/24VAC Special features Dear Customers! By selecting this product, you have decided to use a professional device that guarantees highest quality and reliability. We would like to thank you very much for your confidence and kindly ask you to read the following instructions carefully before installation and operation in order to take full advantage of all quality features regarding this product. CAUTION CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE THE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED PERSONNEL. The lighting flash with an arrowhead symbol, within an equilateral triangle is intended to alert the user to the presence of non-insulated dangerous voltage within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. INFORMATION This equipment has been tested and found to comply with limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at its own expense. WARNING Changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate the equipment. CAUTION – To prevent electric shock and risk of the fire hazards Do NOT use power source other than that specified. Do NOT expose this appliance to rain or moisture. This installation should be made by a qualified service person and should conform to all local codes. 1. Precautions • Please read the manual carefully before the installation in order to set up the camera correctly and to obtain the best picture quality. • Please keep the manual in good condition for your future reference and service application. • Installation and services should be only carried out by an authorized personnel according to local safety regulations. • If any liquid or solid matter gets into the housing, immediately disconnect the camera from power supply and have it checked by your authorized dealer before reusing. • Avoid installing the camera at extremely hot or cold places. • Avoid installing the camera at a place of high humidity. • Avoid installing the camera at the place exposed to gas or oil. • If you are not a certified person, never try to dismantle the camera. To avoid electric shock, never remove the screws or covers. There are no parts inside that need maintenance by the user. All maintenance should be carried out by qualified personnel. • Keep the top glass of the lens always clean in order to obtain the best picture quality all the time. Be careful not to be stained by fingerprint. • Don't face the camera directly toward sunlight or sunlight reflecting area. Image Sensor may go defective at this condition. • Please give a special attention to keep the unit from dangerous drop or external shock during the process of transportation or handling. • Never try to touch the camera in wet hand. It may cause an electric shock. • Do not expose the camera to radioactivity. It causes a serious damage on the Image Sensor. 2. Limitation of liability This publication is provided “AS IS” without warranty of any kind, either express or implied, including but not limited to, the implied warranties of merchantability, fitness for any particular purpose, or non-infringement of the third party's right. This publication could include technical inaccuracies or typographical errors. Changes are added to the information herein, at any time, for the improvements of this publication and/or the corresponding product(s). 3. Disclaimer of warranty In no event shall seller be liable to any party or any person, except for replacement or reasonable maintenance of the product, for the cases, including but not limited to below: (1) Any damage and loss, including without limitation, direct or indirect, special, consequential or exemplary, arising out of or relating to the product; (2) Personal injury or any damage caused by inappropriate use or negligent operation of the user; (3) Unauthorized disassemble, repair or modification of the product by the user; (4) Inconvenience or any loss arising when images are not displayed, due to any reason or cause including any failure or problem of the product; (5) Any problem, consequential inconvenience, or loss or damage, arising out of the system combined by the devices of third party. (6) Any claim or action for damages, brought by any person or organization being photogenic subject, due to violation of privacy with the result of that surveillance-camera's picture, including saved data, for some reason, becomes public or is used for the purpose other than surveillance. Camera x 1 Auto Iris Lens Plug x 1 C-Mount Adaptor x 1 Installation guide x 1 L-Wrench x 1 (Ø0.84) QUICK INSTALL GUIDE True Day / Night Box Camera ◆ Special features Uncompressed high quality Full HD video with full frame rate Full HD video transmission up to 100M 1920X1080 60p/50p/25p/30p, 1280X720 60p/50p/30p/25p Enhanced WDR performance Quick and easy OSD control Diverse Video output for diverse applications. (HD-SDI & Composite) 2D/3D DNR (Digital Noise Reduction) Defog function Dynamic digital zoom and PIP Pelco-C support (CVBS output with optional controller) Privacy Masking (8 Polygon Area) Supports 15 Languages RS-485 Interface for external control of OSD (Using controllers, etc. ) 12VDC or 12VDC/24VAC 4. Package 5.Name and function of each part 5‐1. Right side Auto IRIS Lens Connector 5-2. Front / Bottom side 2- 1/4"-20UNC 2- 1/4"-20UNC Fixture can be separated and attached on the bottom side as well. lease use the supplied clamp screws only to change the position of the bracket. Using screws more than 5mm depth can do a serious damage to the inside of this camera. * Use an international standard 1/4”-20 mounting screw to install the camera. Protection Cover Take off the protection cover. 5.Name and function of each part 5-3. Rear side 12VDC HD-SDI CVBS TRx TRx GND D/N POWER ① OSD Control button. ② Power indicator LED Lamp is on when the power is being supplied. ③ CVBS output (BNC Female) Connect coaxial cable for composite video signal out. ④ HD-SDI output (BNC Female) Connect coaxial cable for HD-SDI signal video signal out. ⑤ RS-485 Control port You can control SETUP menu through this port by using external controllers like a remote controller that RS-485 Communication is supported. ⑥ Day & Night Out port This unit can be synchronized by an External IR LED kit through this port. Low : Color(LED Off), High : B/W(LED On) ⑦ Power input terminal Connect to the power source. Polarity of the power is self-configured. (Non-polarity). 6. Installation 6-1. Lens Lens is not supplied with the unit. C-Mount or CS-Mount type of lens is useable. Please select a lens that has a good F-Stop number in order to get the best picture quality. Use of DC auto iris lens is recommended to achieve the best results for operating this product effectively. ☞ Caution Please make sure the surface of the lens be always clear. Clean dirt or water drops with soft cloth in order to avoid the picture blooming or reflection. ☞ Note To get the best image quality, please use recommended lenses from the manufacturer or camera supplier. 1. Please take off the sleeve outer cable of the lens by 10mm. 2. Please take off the sleeve inner cable of the lens by 2mm. 6-2. When using an auto iris lens (DC-drive) ① ② ③ ④ ⑤ ⑦ ⑥

DVR Stand Alone DVR Optical Transmitter Optical cable Optical Receiver 40Km Repeater Coaxial 5C-HFBT Max. 100M LENS DC SHUTTER D-WDR WDR ATW AUTO 2DNR CAM TITLE LANGUAGE SHARPNESS FRAMERATE FACTORY 3DNR D-EFFECT DEFECT MONITOR VIDEO.OUT LSC RESOLUTION RETURN RETURN LEVEL MOTION RS485 AWC→SET COLOR B/W INDOOR OUTDOOR SMART NR PRIVACY PELCO-C RETURN VERSION RETURN MANUAL BLC HSBLC OFF AGC DEFOG SENS-UP BRIGHTNESS RETURN MANUAL EXPOSURE BACKLIGHT WHITE BAL DAY&NIGHT NR SPECIAL ADJUST RESET EXIT SETUP 6. Installation 3. Solder the wires on the pin-connector (iris-jack) supplied with the lens according to the pin configuration as shown in the drawing. 4. Assemble the lens. 5. Connect the Auto Iris jack. · Please assemble C-Mount adaptor. · C-Mount adaptor is included in the package. · Fix the lens by turning it clockwise. 6-3. When using a C-mount Lens C-Mount ADAPTOR 6-4. When using a CS-mount Lens · Take off the Protection cover. · Take off the C-MOUNT adaptor. · Assemble the CS-MOUNT lens by turning it clockwise. - When used with an Auto Iris lens, please insert the iris jack into the Iris socket which is located on the right side of the camera. - Please set the lens mode by using OSD Switch on the back of the camera depending on the type of selected lens. CS-Mount Lens 6. Installation - Insert the iris jack into the iris socket. LENS Connector - Control the Lens (CS-Mount) to focus the Lens. CS-Mount - Fix the CS-Mount using the L-Wrench. L-Wrench * Lens adjustment Tele-Wide Near-Far 6-5. Application of HD-SDI output Impedance alliance in the system connection.Make sure to connect the cable with the power off. Please locate the impedance switch of each equipment as instructed. Locate the switch to Hi-z position for the interim equipments Locate the switch to 75 for the last equipment. 6. Installation 6-6. Power 12VDC camera Please make sure to use a UL / CE approved and 12VDC / 450mA regulated power supply. 12VDC / 24VAC Dual Power camera (Option) Please make sure to use a UL / CE approved and 12VDC / 450mA, 24VAC / 220mA regulated power supply. 6-7. OSD Manual for functions control 6-8. Setting up the menu Settings can be made using the OSD Switch located on the back of the camera. 1. Press the button to access the SETUP mode. The SETUP menu is displayed on the monitor. 2. Please select any function you wish to activate by using the UP / DOWN selections. The cursor can be moved up or down by using the UP / DOWN selections. Position the cursor to point to the function you wish to operate. 7. Dimension (mm) 66 64 138.8 8. Troubleshooting Before asking for repairs, refer to the following table. If the problem persists, please contact the dealer or your service center. Problems Troubleshooting Nothing appears on the screen. · Please check that the power cord and line connection between the camera and monitor are fixed properly. · Please check that you have properly connected VIDEO cable to the camera VIDEO output jack. The dim image on the screen. · Is lens stained with dirt? Clean your lens with soft,clean cloth. · Set the monitor to proper condition. · If the camera is exposed to too strong light, change the camera position. · Please check if the power supply is within the specification& cables.(Due to the voltage drop with distance and gauges, LED Will light poor) · Adjust the contrast feature of the monitor. · If there is an intermediate device, set the 75Ω / Hi-Z properly. (Please check the impedance) · Please check if the power supply is regulated and is within the standard requirement of the products. · Please check the setting of White Balance setup. · Please check if the camera is facing directly towards sunlight or fluorescent light. The dark image on the screen. The camera is not working properly, and the body of the camera is hot. Color is not correct. The screen is flickering. RS-485 communication fails. · Please check the polarity between RS-485 Control Port and RS-485 cable. 485 Control Board Connection Port (+)CONNECTION TERMINAL(TRX+) (-)CONNECTION TERMINAL(TRX-) RS-485 Control Port 485+ 485- * RS-485 Communication establishment initial value. · Please check if the RS-485 Communication establishment initial value. UART MODE RET PKT Item Camera ID BAUD RATE Initial value 1 9600 8-NONE-1 ENABLE · We recommend that you make ground connect between camera and controller in order to maintain safety communication control. 9. Specifications Effective Pixels Sensor Device Sony 1/2.8 inch 2.1MP Exmor CMOS Sensor 1952(H) x 1116(V) 2.18 Megapixel 1944(H) x 1104(V) 2.14 Megapixel Progressive Scan More than 1100 TVL More than 52dB 0.2 Lux (AGC On) 1/30s Default,(Long Exposure Mode, ~1Sec) Total Pixels Horizontal S/N Ratio Min. Illumination Video Output Format Digital Output Day & Night Serial Port AV Output Power Source Operating Current Operating Humidity Weight ( Approx.) Effective Pixels Shutter Speed Video Output 1920 x 1080 60p / 50p / 30p / 25P, 1280 x 720 60p / 50P / 30p / 25p (Mode Select) 1.485G/s, 2.97G/s HD-SDI Output, 1Port CVBS 1V p-p Composite. 75 Ohms SDI Output True Day & Night with ICR Pelco-C support analog video only CS Mount Lens Option (2.8 ~ 12mm & 5 ~ 50mm 2Mega Lens) DC IRIS / Manual Lens Mode Select DC12V(24VAC / 12VDC Dual Power Option) 170mA -10°C ~ 50°C -20°C ~ 60°C (Humidity : 0%RH ~ 90%RH) 1500g Video Mode / D&N / AWB / AE / Privacy Mask / Flickerless / Brightness / Sharpness / Mirror & Flip / DSS / DNR, etc. MODEL 2 Megapixel FULL HD Box Camera Scanning System Lens Measurement (mm) Lens Control Operating Temperature Storage Temperature OSD specifications are subject to change without prior notice. * 66(W) x 64(V) x 138.8(L) 140623-1SFHD2