Weinmann FW7405M/14 Description And Operating Instructions

4 Connecting socket for power supply cable 3 Adapter Negative pole (external) Positive pole (internal) 5 Power plug 1 Mains charger 6 Power supply cable

1.1 Intended purpose . . . . . . . . . . . . . . . . . . . . 4 1.2 Functional description . . . . . . . . . . . . . . . . . 4 2. Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . 5 2.1 General . . . . . . . . . . . . . . . . . . . . . . . . . . 5 2.2 Special markings on the unit. . . . . . . . . . . . . 6 3. Unit Combinations . . . . . . . . . . . . . . . . . . . . . . . 7 3.1 Weinmann units. . . . . . . . . . . . . . . . . . . . . 7 4. Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 4.1 Start-up. . . . . . . . . . . . . . . . . . . . . . . . . . . 8 4.2 End of operation . . . . . . . . . . . . . . . . . . . . 8 5. Hygiene Treatment . . . . . . . . . . . . . . . . . . . . . . . 9 6. Functional Check . . . . . . . . . . . . . . . . . . . . . . . . 9 7. Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . 10 7.1 Disposal. . . . . . . . . . . . . . . . . . . . . . . . . 10 8. Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . 10 9. Scope of Supply . . . . . . . . . . . . . . . . . . . . . . . . 11 9.1 Standard scope of supply . . . . . . . . . . . . . 11 9.2 Spare parts. . . . . . . . . . . . . . . . . . . . . . . 11 10. Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . 12 11. Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

1. Description of Unit 1.1 Intended purpose The mains charger FW7405M/14 is an accessory for medical devices. It can be used to operate or charge units which require a DC voltage of 12 - 13.8 V as the supply voltage. A list of the units permit- ted can be found in „3. Unit Combinations" on page 7. The mains charger FW7405M/14 is only designed for use indoors. 1.2 Functional description The mains charger FW7405M/14 converts mains voltage. It transforms 100 – 240 V AC voltage into DC voltage of 13.8 V, thus delivering the optimum supply voltage for the units ACCUVAC, ACCUVAC Basic, ACCUVAC Rescue, MEDUMAT Elektronik and MODUL CapnoVol. A pilot lamp indicates that the volt- age has been converted.

2.1 General For your own safety, the safety of your patients, and to comply with the requirements of the directive 93/42/EEC, please observe the following points: • Please read these operating instructions through carefully. They are a part of the unit and must be available at all times. • Before using the mains charger FW7405M/14 you must understand how to operate it. • The mains charger FW7405M/14 should only be used for the intended purpose described (see "1.1 Intended purpose" on page 4). • Only have repair work carried out by Weinmann or specialist staff. • Please do not use the unit if damaged. Cables, plugs and housings must be in perfect condition. • Please observe the general safety provisions for handling electrical equipment. • Always disconnect the power plug by removing the plug from the socket and not by pulling on the cable. • Malfunctions and a lack of biocompatibility may result if third-party articles are used. Please bear in mind that in these cases any warranty entitlement and liability shall lapse where the accessories rec- ommended in the operating instructions or original spare parts are not used.

Nameplate Year built Serial number of the unit Input voltage Output voltage CE marking according to 93/42/EEC relating to medical devices Observe operating instructions Protection by use of class II equipment Applied part type CF Only for use indoors Do not dispose of unit as domestic waste SN:

3.1 Weinmann units The mains charger FW7405M/14 can be used to operate the following Weinmann units with the optimal supply and charging voltage: Suction pumps: – ACCUVAC – ACCUVAC Basic – ACCUVAC Rescue Emergency respirator: – MEDUMAT Elektronik Modules: – MODUL CapnoVol Connecting cables are available as accessories for the units (see "9. Scope of Supply" on page 11).

of the mains charger FW7405M/14. 2. Then insert the power plug 5 in a mains socket. Note: Illumination of the pilot lamp 2 indicates that the required DC voltage of 13.8 V has been gen- erated. 3. Select the right connecting cable from (see "3. Unit Combinations" on page 7). 4. Insert the appropriate end of the connecting cable in the coupling 3 of the mains charger. 5. Connect the other end to the unit to be supplied. 4.2 End of operation Once you no longer need the mains charger FW7405M/14: 1. Switch off the unit connected. 2. Disconnect the mains charger and the unit con- nected. 3. Remove the power plug 5 from the mains socket. 6 3 4 5 5

Caution! Do not allow moisture to enter the unit. If necessary, e.g. after exceptional soiling, you can also disinfect the housing, output line and power sup- ply cable. Please observe the instructions provided for the disinfectant used. We recommend that you wear suitable gloves when disinfecting the unit (e.g. house- hold or disposable gloves). Unit The housing, output line and power supply cable of the charger FW7405M/14 are cleaned by being simply wiped over with disinfectant. We recommend TERRALIN for this purpose. 6. Functional Check Each time before use • Insert the power plug in the mains socket. • Check that the pilot lamp is lit up. • If it is not lit up, remove the power plug from the mains socket and have the unit repaired (see "7. Troubleshooting" on page 10). • Please check the entire unit for damage. The hous- ing, cable and plug should not be damaged. If you notice damage to the unit, have this rectified by Weinmann .

of the unit properly, please contact a licensed and cer- tified electronic waste disposal merchant. Names and addresses can be obtained from your Environmental Officer or municipal authorities. 8. Maintenance The mains charger FW7405M/14 is maintenance- free. You should nevertheless perform regular function- al checks (see "6. Functional Check" on page 9). We recommend only having repair work carried out by Weinmann. Malfunctions Rectification Pilot lamp does not light up Have repair performed at plant. Power cable damaged Replace WM 24133 power cable

11 9. Scope of Supply 9.1 Standard scope of supply Mains charger FW7405M/14, complete WM 2610 9.2 Spare parts In order to operate the units listed under “3. Unit Combinations” on page 7 you re- quire the appropriate connecting cables. For further details in this regard consult the operating instructions for the units. Name Article no. Mains charger FW7405M/14 Power supply cable WM 24133 Operating instructions WM 66036 Name Article no. Power supply cable WM 24133 Operating instructions WM 66036

Subject to design modifications Mains charger Device class as per 93/42/EEC I Dimensions WxHxD in mm 130 x 36 x 60 Weight approx. 280 g Temperature range – operation – storage 0 °C to +40 °C -40 °C to +70 °C Electrical connection 100 to 240 V ~, 50 to 60 Hz Power consumption 1.1 A Output 13.8 V /3.5 A Classification as per EN 60601-1 – type of protection from electric shock – level of protection from electric shock – level of protection from moisture Protection class II Type CF IP 40 Electromagnetic compatibility (EMC) as per EN 60601-1-2 – radio interference suppression – immunity to interference EN 55011 DIN EN 61000-4 parts 2– 6, part 11 Length output line 0.5 m Length power supply cable approx. 2.5 m

quirements, will remain free from defects for a period of two years from date of purchase. For products whose durability is clearly indicated as less than two years, the warranty expires on the expiration date indicated on the packaging or in the user’s manual. • Claims against the warranty can be made only when accompanied by the sales receipt, which must show salesperson and date of purchase. • We offer no warranty in the case of: – Disregard of usage instructions – Operating errors – Improper use or handling – Third-party intervention by non-authorized persons for the purpose of device repair – Acts of God, e.g., lightning strikes, etc. – Transport damage as a result of improper packaging of returned items – Lack of maintenance – Operational and normal wear and tear, which includes, for example, the fol- lowing components. – Filter – Batteries or non-rechargeable batteries – Articles for one-time usage, etc. – failure to use original spare parts. • Weinmann is not liable for consequential harm caused by a defect if it is not ba- sed on intention or gross negligence. Weinmann is also not liable for minor phy- sical injury to life or limb resulting from negligence. • Weinmann reserves the right to decide whether to eliminate defects, to deliver a defect-free item or to reduce the purchase price by a reasonable amount. • If Weinmann rejects a claim against the warranty, it assumes no expense for trans- port between customer and manufacturer. • Implied warranty claims remain unaffected by these changes.

Weinmann Geräte für Medizin GmbH+Co. P.O. Box 540268 · D-22502 Hamburg Phone +49/40/5 47 02-0 Fax +49/40/5 47 02-461 E-mail [email protected] Internet www.weinmann.de For decades Weinmann has been developing, producing and marketing medical devices for markets around the world. In cooperation with our partners we design economic health systems for diagnosis and therapy in Sleep Medicine, Home Mechanical Ventilation, Oxygen Medicine and Emergency Medicine.