Performance Tool W50094 Owner's Manual

DRILL DRIVER WARNING! READ, UNDERSTAND AND FOLLOW ALL INSTRUCTIONS AND WARNINGS BEFORE OPERATING THIS TOOL. FAILURE TO DO SO MAY RESULT IN PERSONAL INJURY AND/OR PROPERTY DAMAGE AND WILL VOID WARRANTY. Some dust created by power sanding contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. An example of this type of chemical is lead from lead based paints, Crystalline Silica from bricks and cement or other masonry, Arsenic and Chromium from chemically treated lumber. Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure: work in a well ventilated area and work with approved safety equipment, such as dusk masks that are specially designed to filter out microscopic particles. LIMITED WARRANTY PERFORMANCE TOOL® extends only the following warranties, and only to original retail purchasers. These warranties give specific legal rights. Except where prohibited by local law, the law of the State of Washington governs all warranties and all exclusions and limitations of warranties and remedies. There may be other rights which vary from state to state. PERFORMANCE TOOL® warrants the product to be free from defects in materials and workmanship under normal use and service. A defective product may be returned for a free replacement within 90 days from the date of purchase, provided that product is returned to place of purchase immediately after discovery of defect. After 90 days and up to one year from date of purchase, PERFORMANCE TOOL® will replace at no charge any parts which our examination shall disclose to be defective and under warranty. These warranties exclude blades, bits, punches, dies, bulbs, fuses, hoses, and other consumables which must be replaced under normal use and service. These warranties shall not apply to any product or part which is used for a purpose for which it is not designed, or which has been repaired or altered in any way so as to affect adversely its performance or reliability, nor shall these warranties apply to any product or part which has been subject to misuse, neglect, accident or wear and tear incident to normal use and service. PERFORMANCE TOOL® does not authorize any other person to make any warranty or to assume any liability in connection with its products. Except for warranties of title and the limited express warranties set forth above, PERFORMANCE TOOL® makes no express or implied warranties of any kind with respect to its products. In particular, PERFORMANCE TOOL® makes no implied warranty of merchantability and no implied warranty of fitness for any particular purpose, except that for goods purchased primarily for personal, family or household use and not for commercial or business use, PERFORMANCE TOOL® makes an implied warranty of merchantability (and, if otherwise applicable, an implied warranty of fitness for a particular purpose), but only for the particular qualities or characteristics, and for the duration, expressly warranted above. The laws on limitation of implied warranties may differ from state to state, so the above limitations may not apply in all cases. PERFORMANCE TOOL® shall not be liable for consequential, incidental or special damages resulting from or in any manner related to any product, or to the design, use, or any inability to use the product. The sole and exclusive remedy for a defective product or part shall be the repair, or replacement thereof as provided above. The laws on limitation of remedies or on consequential, incidental or special damages may vary from state to state, so the above limitations may not apply in all cases. OWNER’S MANUAL Item Number W50094

1. Keep work area clean. Cluttered areas invite injuries. 2. Observe work area conditions. Do not use machines or power tools in damp or wet locations. Don’t expose to rain. Keep work area well lighted. Do not use electrically powered tools in the presence of flammable gases or liquids. Do not bring combustible materials near the tools. 3. As with any tool, use common sense when operating. Do not wear loose clothing or jewelry that could become caught by moving parts, causing injury. Operate tool a safe distance from yourself and others in the work area. 4. Keep children away. Children must never be allowed in the work area. Do not let them handle machines, tools, hoses or extension cords. 5. Store idle equipment. When not in use, tools must be stored in a dry location to inhibit rust. Always lock up tools and keep out of reach of children and other untrained persons. Switch off all unused electrical tools when stored. Tools are dangerous in the hands of untrained users. 6. Always wear approved eye protection when using tools. If raising dust, wear a suitable mask. 7. Work Safe. When wearing gloves to operate the tool, make sure that the gloves do not interfere with operating the Trigger. Test your gloves with the Trigger before attaching the unit to an air source. Keep your finger away from the Trigger until you are ready to work. Never start the tool unless you have a firm grip with both hands and you are positioned at your work piece or area. Before using the tool, know what is directly underneath the work area or work piece. The tool can quickly penetrate material. If working directly on the ground, make sure you are not directly above shallow cables, lines, or pipes. Keep your limbs and body clear of the tool. If an accessory or attachment breaks off, the tool tends to surge forward suddenly. Operate tool a safe distance from yourself and others in the work area. Make sure the immediate area is clear of other people or animals. Spectators must stay at a safe distance. Never point the tool or the air hose (not included) at anyone. Keep proper footing and balance at all times. Do not reach over or across running machines, hoses, etc. 8. Do not operate any tool if under the influence of alcohol or drugs. Read warning labels on prescriptions to determine if your judgment or reflexes are impaired while taking drugs. If there is any doubt, do not operate any tool. 9. Be sure air is in OFF position when connecting tool to air supply. 10. Use only those accessories that are designed for use with tools. For example, with impact wrenches do not use ordinary sockets. Use impact sockets for all air tools. 11. Be sure to disconnect tool from air supply before changing accessories, performing service on tool and when not in use. 12. Follow air source manufacturers' directions for connection of regulators, filters, and other accessories to air source. Do not install quick couplers directly on tool as they put unnecessary strain on the air inlet threads possibly causing them to wear out prematurely. Instead, install them on a short length of air hose attached to the tool. 13. Check for damaged parts. Before using any tool, any part that appears damaged should be carefully checked to determine that it will operate properly and perform its intended function. Check for alignment and binding of moving parts; any broken parts or mounting fixtures; and any other condition that may affect proper operation. Any part that is damaged should be properly repaired or replaced by a qualified technician. WARNING! READ, UNDERSTAND AND FOLLOW ALL INSTRUCTIONS AND WARNINGS BEFORE OPERATING THIS TOOL. FAILURE TO DO SO MAY RESULT IN PERSONAL INJURY AND/OR PROPERTY DAMAGE AND WILL VOID WARRANTY. IMPORTANT SAFETY INFORMATION 14. Maintenance. For your safety, maintenance should be performed regularly by a qualified technician using original PERFORMANCE TOOLS® replacement parts. Failure to do so can lead to accidents for the operator. Use of any other parts will void the warranty. Only use accessories intended for use with this tool. Approved accessories are available from Performance Tool®. Use only accessories that are recommended by the manufacturer for your model. Accessories that may be suitable for one tool may become hazardous when used on another tool. Some dust created by power sanding contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. An example of this type of chemical is lead from lead based paints, Crystalline Silica from bricks and cement or other masonry, Arsenic and Chromium from chemically treated lumber. Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure: work in a well ventilated area and work with approved safety equipment, such as dusk masks that are specially designed to filter out microscopic particles. WARNING: Repetitive motions or exposure to vibration may be harmful to your hands and arms. WARNING: This product and its packaging contain a chemical known to the State of California to cause cancer, birth defects, or other reproductive harm. WARNING: The warnings, cautions, and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may occur. It must be understood by the operator that common sense and caution are factors which cannot be built into this product, but must be supplied by the operator. Read and understand all of the instructions provided in the instruction manual of this product, as well as, any other tool (s) used with this product. ! 1. Hold the tool by insulated gripping parts while performing an ongoing operation in which the cutting element or screw may contact hidden wiring. Contact with a wire “under stress” can put the metal parts of the power tool exposed “under stress” and cause an electric shock to the operator. 2. Use appropriate detectors in order to show the hidden supply ducts or consult local companies. Contact with electrical lines can cause a fire or electric shock. Damage to a gas line can cause an explosion. Drilling a water pipe can cause damage. 3. Stop the appliance immediately when the tool blocks up. Expect coupling reactions that can cause major consequences. The tool crashes if: The appliance is overloaded If you get stuck in the piece on which you are working 4. Hold tightly the portable electric tool. Because of the unscrewing or screwing, may have, high reaction instantly. 5. Fix the piece that is going to be worked on. A piece well-set or fixed in a vise piece is fixed more securely than held in hands. 6. Keep workspace clean. Mixtures of materials are particularly dangerous. Dust from light metals can be explosive or flammable. 7. Before putting off the portable electric tool, wait until it is completely stopped. There is a risk that the machine blocks up, which represents a loss of control over it. 8. Do not open the battery. Risk of short-circuit. Protect the battery from heat sources such as direct exposure to sun and heat. There is a risk of explosion. 9. Vapors can escape in case of damage and improper use of the battery. Ventilate the workplace and in case of discomfort, consult a doctor. Vapors may pose irritation in the airways. 10. If the battery is defective, liquid can go out and come into contact with nearby objects. Control the elements affected. Clean or change them, if necessary. SPECIAL SAFETY RECOMMENDATIONS

Gear 1............................................................................1 0 to 400 U / min Gear 2..........................................................................2 0 to 1400 U / min Level rotation coupling.....................................................................18 + 1 Max. torque (soft / hard) ............................................................. 22 ft. lbs. Rotate to the left / right ........................................................................ Yes Chuck capacity ................................................................................ 3/8 in. Battery charger voltage ...........................................100-240V~/ 50-60 Hz Battery charge time ............................................................................1 hr. Noise and vibration values have been determined according to EN60745. LpA sound pressure level .......................................................61.8 dB (A) KpA Imprecision ...........................................................................3 dB (A) LWA Sound power level ..........................................................72.8 dB (A) Kwa imprecision ..........................................................................3 dB (A) CAUTION: Use noise protection. Exposure to noise can lead to loss of hearing. Technical Specifications are subject to change without notice. TECHNICAL SPECIFICATIONS: 1. Quick Change Drill Chuck 2. 1/4 in. Hex Bit Driver Chuck 3. Torque Adjustment Ring 4. Gear Selector 5. Directional Switch & Trigger Lock 6. Battery Lock Button 7 6 9 11 5 4 3 1 10 8 7. Battery 8. Trigger 9. LED Light 10. Battery Status Display 11. Battery Charger 2

This will ensure that the safety of the tool is maintained. 2. Unplug tool and charger from the wall outlet before cleaning. CLEANING 1. Keep protection devices, air vents and the motor housing as clean (dust free) as possible. Clean the tool with a clean cloth or clean with compressed air at low pressure. 2. We recommend cleaning the tool directly after each use. 3. Clean the tool regularly with a damp cloth and a little soap. Do not use any cleaner or detergent, they can damage the plastic parts of the tool. Ensure that no water enters the tool. MAINTENANCE 1. Recharge the battery regularly, for example once every six months. ENVIRONMENTAL PROTECTION This device uses electronic components, so they should not be deposited with household garbage! Please help by collaborating to protect resources and the environment. Dispose of these products through relevant recycling services, if any. For questions on this matter, please contact your local waste management or a specialized site. CERTIFICATION The tests have been carried out in accordance with following standards: EN 60745-1:2009/A11:2010 EN 60745-2-1: 2010 EN 60745-2-2: 2010 CARE AND MAINTENANCE 1. Keep the area clean and well lit. Cluttered or dark areas can cause accidents. 2. Do not use power tools in explosive environments, e.g. in the presence of flammable liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes. 3. Keep children and people away during the use of the tool. Distractions can cause you to lose control of the tool. WORKPLACE SECURITY 1. It is necessary that the power tool plugs are adapted to the base. Never modify the plug in any way. Do not use adapters with earthed tools. Unmodified plugs and adapted bases reduce the risk of electric shock. 2. Avoid contact with grounded objects such as pipes, radiators, stoves and refrigerators. There is an increased risk of electric shock if your body is in contact with grounded surfaces. 3. Do not expose power tools to rain or wet conditions. The penetration of water into a tool increases the risk of electric shock. 4. Do not misuse the cable. Do not use the cord for carrying, pulling or unplugging the tool. Keep the cord away from heat, oil, edges or moving parts. Damaged or entangled cords increase the risk of electric shock. 5. When operating a tool outside, use an extension cord suitable for outdoor use. Using a cable suitable for outdoor use reduces the risk of electric shock. 6. If it is necessary to use the tool in a location with moisture, use a secure supply with residual current device (RCD). The use of an RCD reduces the risk of electric shock. ELECTRICAL SAFETY 1. Be aware of what you are doing and use common sense while using the tool. Do not use a tool when you are tired or under the influence of drugs, alcohol or medication. A moment of distraction while using a tool can cause serious personal injury. 2. Use safety equipment. Always wear eye protection. Safety equipment such as dust masks, non-slip safety shoes, helmets or ear protection used in appropriate conditions will reduce the risk of injury. 3. Avoid accidental starting. Make sure that the switch is in the off position before plugging in to power or battery, collect or transport. Carrying tools with your finger on the trigger or plugging the tool in with the trigger pulled can cause accidents and injury. 4. Remove any adjusting key before turning the tool on. A key left attached to a rotating part of the tool may result in personal injury. 5. Do not rush. Maintain proper footing and balance at all times. This allows better control of the tool in unexpected situations. 6. Dress appropriately. Do not wear loose clothing or jewelry. Keep hair, clothing and gloves away from moving parts. Loose clothing, jewelry or long hair can get caught in moving parts. 7. If devices for connecting equipment for extraction and dust collection are supplied, make sure they are connected and properly used. Use of dust collection can reduce risks due to dust. SECURITY STAFF 1. Do not use any other charger than the one specified by the manufacturer. A charger that fits to a type of battery can cause a risk of fire when used with other types of batteries. 2. Do not use tools with batteries other than those specified. The use of any other type of battery may create a risk of injury and fire. 3. If the batteries are not used, keep them away from other metal objects such as clips, coins, keys, nails, screws or other small objects that can lead to a connection from one terminal to another. Short-circuiting the terminals of a battery can cause burns or fire. 4. In bad conditions, liquid may be ejected from the battery; avoid any contact. In case of accidental contact, flush with water. If the fluid comes into contact with eyes, seek medical assistance. The ejected battery fluid may cause irritation or burns. USING MACHINES WITH BATTERY AND PRECAUTIONS FOR USE 1. Do not force the tool. Use the right tool to the application being performed. A suitable tool will do the job better and more safely if used for the purpose for which it has been built. 2. Do not use the tool if the switch does not allow to turn it on or off. Any tool that can not be controlled by the switch is dangerous and must be repaired. 3. Disconnect the power source supply or battery block tool before changing accessories or before storing the tool. These preventive safety measures reduce the risk of accidental starting of the tool. 4. Keep the tool off away from children and do not allow to be used by people who are not familiar with the tool. Tools are dangerous in the hands of inexperienced. USE AND MAINTENANCE OF THE TOOL 1. Do not force the tool. Use the right tool for the application being performed. A suitable tool will do the job better and more safely if used for the purpose for which it has been built. 2. Do not use the tool if the switch does not allow you to turn it on or off. Any tool that can not be controlled by the switch is dangerous and must be repaired. 3. Disconnect the power supply and battery charger before changing accessories or before storing the tool. These preventive safety measures reduce the risk of accidental starting of the tool. 4. Keep the tool away from children and do not allow tool to be used by people who are not familiar with the operation of the tool. Tools are dangerous in the hands of inexperienced operators. 5. Make sure the tools moving parts are not aligned or blocked, that it has not broken any parts or any other condition that may affect the operation of the tool. In case of damage, take the tool to a repair service before using it again. Many accidents are caused by poorly maintained tools. 6. Tools used for cutting, with sharp pieces that have had good maintenance, are less likely to become blocked and are easier to control. 7. Use the tool, accessories and blades, etc. according to these instructions, taking into account the working conditions and the work to be done. The use of the tool for operations other than those provided can lead to dangerous situations. USE AND MAINTENANCE OF THE TOOL 5 6

ceramic and plastic materials. This tool should not be used for purposes other than those described above. BEFORE USE Before turning on the cordless drill, read the following notes: 1. Charge the battery with the provided charger. A fully discharged battery recharges in about one hour. 2. Use only appropriate bits and tip screwdrivers. 3. When screwing and drilling into walls, check for hidden power, gas or water lines. CHARGING THE BATTERY 1. Remove the battery from the tool by depressing both battery lock buttons and pulling down. 2. Check if the power voltage on the rating plate corresponds to the voltage available. 3. Plug charger's power lead into top of battery. The red LED indicates that the battery is charging. Once charged, the red LED turns off and the green LED stays on continuously. 5. During charging, it is normal for the battery to warm slightly. If you can not charge the battery, check: - That the socket has voltage. - That the charger contacts are reliable. TORQUE SETTINGS The tool has a mechanical torque adjustment ring (3) with 18 + 1 different settings. Setting 1 is the lowest torque setting and 18 the highest. A clicking will be heard and felt when the torque setting has been reached. Use the right setting for the application. This will help prevent overtightening and stripping of fasteners. The last torque setting ( ) bypasses the mechanical ratchet and applies maximum torque. Use this setting for using drill bits or when maximum torque is required. ATTENTION! Do not adjust the torque adjustment ring until the tool comes to a complete stop. DRILLING To drill, turn the torque adjustment ring to the "drill" setting ( ). While on the "drill" setting the safety clutch is deactivated so when drilling, the maximum torque is available. SWITCHING THE DIRECTION OF ROTATION The directional switch (5) above the trigger allows you to choose the rotational direction of the tool or set the trigger lock. You can select clockwise (forward) rotation, counter clockwise (reverse) or trigger lock. To prevent damaging the tool, do not change the direction of rotation while the tool is running. When the slide switch is in the center position (trigger lock), the trigger is locked and the tool is inoperable. TRIGGER The trigger (8) allows you to adjust the speed continuously, depending on the intensity with which the trigger is pulled. SWITCHING THE SPEED Note: Only change the gear selector (4) when the driver is not in operation. In the first gear (gear selector position 1) a speed of 400 min-1 and maximum torque is achieved. This setting is suitable for all fastening applications. In the second gear (gear selector position 2) a speed of about 1400 min-1 is achieved to carry out drilling operations. OPERATION DISPLAY BATTERY STATUS Three color LEDs (9) indicate the status whenever the ON / OFF button is pressed. - All LEDs are lighted: the battery is fully charged. - Yellow and red LEDs lighted: the battery has charge. - Red LED lighted: the battery is empty and needs to be recharged. LED DISPLAY The LED light (10) can illuminate the screwing and unscrewing area under unfavorable lighting conditions. The LED light illuminates automatically, any time the on / off trigger is pulled. TOOL CHANGE The cordless screwdriver is equipped with a quick coupling drill chuck with automatic lock. To install removable chuck: · Verify the locking ring is depressed to the unlock position (see arrow indicators on the locking ring). · Insert the drill chuck over the ¼ in. quick connect chuck and align so it seats all the way down. · Push locking ring down into the "lock" position. You should hear / feel a click and you should not be able to remove the drill chuck. · To remove, follow the previous steps in reverse. OPERATION