Videx 6276 Manual 

1 6200 Series Art. 6276 - Installation instructions Art. 6276 3.5" colour display videophone 27 mm 144 mm 182 mm Fig. 1 +VD +20 V1 V/V2 GNDV L – LB AL DOL EXTC SW SW DSW1 DSW2 PT1 PT2 VR1 PT3 SW2 A I B D G E H F C Fig. 2 ART. 6276 VX2200 6200 SERIES VIDEOPHONE FOR SYSTEMS USING COMPOSITE VIDEO SIGNAL (COAX) OR BALANCED (TWISTED PAIR) DESCRIPTION Surface mount videophone incorporating a 3.5” Hi-Res full col- our active matrix LCD monitor, with “camera recall”, “door open/ concierge call”, “service” and “privacy” button. 2 LED’s one for generic use (door opening usually) and one to indicate privacy service enabled. Programmable settings: privacy duration, video mode (coax or balanced), melody and number of rings. Adjustments: call tone volume (3 levels), microphone volume, picture hue, contrast and brightness. LEGEND A � Connection terminals B � 8 Way dip switch bank to set videophone address C � 4 Way dip switch bank to set video mode D � Contrast adjustment trimmer E � Hue adjustment trimmer F � Microphone volume adjustment trimmer G � Brightness control sliding wheel H � Call tone volume switch I � RJ-45 connector PUSH BUTTONS Service button When pressed, shorts terminal SW to SW (Max 24 Vdc 50mA). Privacy service Press to enable the privacy service. The LED turns on. The service is deactivated by pressing again the same but- ton or when the programmed time expires. Door Open Push Button • During a conversation, operation of this button will release the door from where the call originated. This will be confirmed by an acoustic tone. If terminal DOL is connected, the “door open” LED under the symbol will also illuminate. • When the system is in stand-by, picking up the handset and pressing the buttons will book a call to the concierge (If available). Camera recall When the system is in standby (no calls on the system), pick up the handset then press this button to open the SPEECH/VIDEO to the door station. Press as many time as the ID value of the door panel to connect to. ENG

2 6200 Series Art. 6276 - Installation instructions LEDS (FIG. 1) LED Privacy on LED It illuminates when the privacy service is enabled, when pressing the service button or during pro- gramming mode. LED Generic use LED It is controlled from the terminal DOL. Normally used to signal the door status (open or closed). CONTROLS (FIG. 1 AND FIG. 2) PT1 Contrast adjustment trimmer* Rotate anticlockwise to increase or clockwise to decrease. *Not available in some LCD versions. PT2 Hue adjustment trimmer Rotate anticlockwise to increase or clockwise to decrease. VR1 Microphone volume adjustment trimmer Rotate anticlockwise to decrease or clockwise to increase. PT3 Brightness control sliding wheel Rotate anticlockwise to increase or clockwise to decrease (when videophone is closed). SW2 Call tone volume switch 3 levels: low, medium and high. PROGRAMMING The programmable settings are: • Privacy service duration (from 15 minutes to 20 hours or infinte); • Melody (9 available); • Number of rings (3 or 6); • Video mode (coax or balanced); • Videophone address (Phone ID). TO SET PRIVACY SERVICE DURATION 1. Press and keep pressed button for 10 seconds to enter privacy service duration programming mode: the LED turns on and the unit emits a “beep“; 2. Press button as many times as required. Each press is equal to 15 minutes: the unit emits a “beep“ every time the button is pressed. I.E.: press 4 times for 1 hour, 12 for 3 hours. Default: infinite. Max value: 20 hours. To program infinite privacy time don’t press any buttons; 3. Wait for some seconds: the LED turns off and the unit emits a “beep“ that confirms the new setting is properly stored; 4. The unit returns to stand-by mode. TO SET MELODY 1. Press and keep pressed button for 10 seconds until the unit plays the current programmed melody and emits a “beep” at the end. 2. Press again button to listen to the available melodies (maximum 9); 3. Once the selected melody has been reached, wait 5 seconds for a “beep”; 4. The new melody will be stored. Note: To set the melody it is required that the videophone is connected in a system where the +20Vdc voltage from Art. 893N1 is always enabled. TO SET THE NUMBER OF RINGS (6 OR 3): Default setting is 6, to set 3 proceed as follows: 1. Turn off the videophone by unplugging the connector from the PCB; 2. Make a short between terminals GNDV and LB on the connector; 3. Plug the connector in and wait for a beep before removing the short; 4. To go back to 6 rings, do the same but two “beeps” will be emitted. Art. 6276 3.5" colour display videophone

3 6200 Series Art. 6276 - Installation instructions Art. 6276 3.5" colour display videophone TO SET THE VIDEO MODE AND TERMINATION The videophone can operate with either composite video signal (coax cable) or balanced video signal (two wires). Switches 1 & 2 of DSW2 are used to set video mode while switches 3 & 4 are for video termination. VIDEO MODE - DSW2 Switches 1,2 Mode Coax Balanced 75 OHM VIDEO TERMINATION - DSW2 Switches 3,4 Termination Enabled Disabled Switches 3 and 4 adjust the video signal impedance. when using more than one videomonitor in parallel (without a video splitter) put both switches in the OFF position on all but the last videomonitor (end of line). VIDEOMONITOR/INTERCOM ADDRESS, VIDEO MODE AND TERMINATION SETUP DSW1 Each intercom is addressed in binary (PHONE ID) using the 8 way dipswitches located on the rear of the unit. Each switch corre- sponds to one bit which can have a value 0 (OFF) or 1 (ON). Each bit corresponds to a decimal weight depending on the position: Switch 1 = decimal 1, 2=2, 3=4, 4=8, 5=16, 6=32, 7=64, 8=128. I.E. to set the address 37, put switches 1, 3 and 6 on (1+4+32=37). SWITCHES DECIMAL WEIGHT ADDRESS 8 7 6 5 4 3 2 1 128 64 32 16 8 4 2 1 OFF OFF OFF OFF OFF OFF OFF ON 0 0 0 0 0 0 0 1 1 OFF OFF OFF OFF OFF OFF ON OFF 0 0 0 0 0 0 1 0 2 OFF OFF OFF OFF OFF OFF ON ON 0 0 0 0 0 0 1 1 3 OFF OFF OFF OFF OFF ON OFF OFF 0 0 0 0 0 1 0 0 4 OFF OFF ON OFF OFF ON OFF ON 0 0 1 0 0 1 0 1 37 ON OFF ON ON OFF ON OFF OFF 1 0 1 1 0 1 0 0 180 CONNECTION TERMINALS SIGNALS +VD 12Vdc output to supply coax video distributor Art. 894N +20 Video power supply 17÷20Vdc V1 Balanced video signal V1 sync. (balanced video signal mode) V/V2 Balanced video signal V2 sync. (balanced video signal mode) Composite video signal (coax video signal mode) GNDV Video power supply ground reference L BUS line – BUS line ground reference LB Local bell input (active low) AL Alarm input (active low) DOL 12Vdc input to supply Aux LED EXTC Call tone output for extension sounder (Art. 512A) SW Service button connection Max 24 Vdc 50mA SW TECHNICAL SPECIFICATION Working Voltage: 17÷20Vdc Power Consumption: 200mA during a call 120mA during a conversation Working Temperature: -10°C +50°C

4 6200 Series Art. 6276 - Installation instructions USING RJ-45 PLUG TO CONNECT THE VIDEOPHONE EIA/TIA-568B 1 2 3 4 5 6 7 8 o O g B b O br BR 8 7 6 5 4 3 2 1 BR br G b B g O o EIA/TIA-568B RJ-45 pin VX2200 Signal 1 and 2 (white-orange / orange) L 3 and 4 (white-green / blue) – 5 and 6 (white-blue / green) + 7 (white-brown) V1 8 (brown) V2 EIA/TIA-568A 1 2 3 4 5 6 7 8 g G o B b O br BR 8 7 6 5 4 3 2 1 BR br O b B o G g EIA/TIA-568A RJ-45 pin VX2200 Signal 1 and 2 (white-green / green) L 3 and 4 (white-orange / blue) – 5 and 6 (white-blue / orange) + 7 (white-brown) V1 8 (brown) V2 NOTE: DO NOT USE CROSS OVER CABLES. IMPORTANT NOTE: SOLID COPPER CABLES MUST BE USED. COPPER COATED STEEL (CCS) AND COPPER COATED ALUMINIUM (CCA) CAN NOT BE USED ON THE SYSTEM. MEMORY BOARD This device is also available in the version with memory board (Art. 6276/VM). If you have that version, please refer to the “6200, 6300, 6400 and 6700 Series Memory Board” user manual for installation and use. The manual is available for download at the following link: https://www.dropbox.com/s/492p16btyqhxmpu/66250782-EN.pdf?dl=0 Art. 6276 3.5" colour display videophone CUSTOMER SUPPORT MANUFACTURER All Countries: VIDEX ELECTRONICS S.P.A. www.videx.it - [email protected] Tel: +39 0734-631669 Fax: +39 0734-632475 VIDEX ELECTRONICS S.P.A. Via del Lavoro, 1 - 63846 Monte Giberto (FM) Italy Tel (+39) 0734 631669 - Fax (+39) 0734 632475 www.videx.it - [email protected] UK Customers: VIDEX SECURITY LTD www.videx-security.com Tech Line: 0191 224 3174 Fax: 0191 224 1559 The product is CE marked demonstrating its conformity and is for distribution within all member states of the EU with no restrictions. This product follows the provisions of the European Directives 2014/30/EU (EMC); 2014/35/EU (LVD); 2011/65/EU (RoHS): CE marking 93/68/EEC.

5 6200 Series Art. 6276 - Installation instructions Art. 6276 3.5" colour display videophone

6 6200 Series Art. 6276 - Installation instructions Art. 6276 3.5" colour display videophone ON/OFF + 13V ART.521B 0 115 sw sw +B +12 _ L BS SL NC C NO TRD PTE V1 V2 / V GNDV 12T B.V. coax others 316x GND Art.4202RV A SE 12Vac ART.893N1 0 L - + - V1V2 L - + - V1V2 C VID A L - + - V1 V2 1.50mm2 1.50mm2 1.50mm2 1.50mm2 1.00mm2 1.00mm2 Address N.3 Art.6276 Address N. 1 Art.6378 1/2 Videx Electronics S.p.A. Via del Lavoro, 1 - 63846 Monte Giberto (FM) Phone: +39 0734 631669 - Fax +39 0734 631669 www.videx.it - [email protected] Title: Notes: Titolo: Note: Autore: Data modifica: Data creazione: Cod.File: Foglio / 224KVD139A.dwg [email protected] 20/10/2016 16/09/2016 1 1 1 2 3 4 5 6 7 8 1 2 3 4 ON Address N. BALANCED ON +VD +20 V1 V/V2 GNDV - LB DOL EXTC SW SW 12Vo SW2 SW1 AL L 12Vi - VM 2 Art.6778 1 2 3 4 5 6 7 8 1 2 3 4 ON Address N. BALANCED ON +VD +20 V1 V/V2 GNDV - LB DOL EXTC SW SW 12Vo SW2 SW1 AL L 12Vi - VM 4 Art.6778

7 6200 Series Art. 6276 - Installation instructions Art. 6276 3.5" colour display videophone L - + - V1V2 L - + - V1V2 C VID A = MAX 40mt A MAX 400mt L - + - V1V2 L - + - V1V2 C VID A Address N.6 Art.6276 Address N.5 Art.6276 Address N.7 Art.6276 Address N.8 Art.6276 Address N.12 Art.6276 Address N.11 Art.6276 Address N. 9 Art.6378 Address N. 10 Art.6378 2/2 L - + - V1V2 L - + - V1V2 VID O Close

8 6200 Series Art. 6276 - Installation instructions 6200 Series Videophone wall mounting instructions 1. In order to install the videophone, it is necessary to remove the cover, which contains all the electronics, from the base: firstly disconnect the handset from the videophone (by removing its plug from the videophone), then press lightly the bottom part of the videophone and simultaneously pulling outwards the upper part as shown in Fig. 1. 2. Put the base of the unit on the wall at approx 135cm from the finished floor to mark the points for the fixing holes “A” (Fig. 2) remembering that the wires “D” (Fig. 3) must be fed through the hole “E” (Fig. 3). If you use the flush mounting box 503, embed it into the wall vertically at approx. 140cm from the finished floor and the base. 3. Following Fig. 3, make the holes “A”, insert the wall plugs “B” and fix the base with the screws “C” feeding the wires “D” into the hole “E”. If you have used the box 503, fix the base to the wall through the holes “F” using the screws “C”. 4. As shown in Fig. 4A, connect the wires to the removable terminals following the provided installation diagram. Connect the ter- minal blocks to the electronics contained in the cover as shown in Fig. 4B. Reinsert the handset and test system before closing. Note: Contrast and hue trimmers can be adjusted only if the videophone is open. Note while testing the system, it is advisable to hold the cover with your hand closing manually the hook switch of the handset (see Fig. 4B reference “G”). 5. Once testing is complete and all the necessary adjustments are made, disconnect the handset from the cover and close the unit as shown in Fig. 5: first hook it on the bottom then push in the top until you hear the clip. 6. Reconnect the handset and hang it as shown in Fig. 6. 1 2 Fig. 1 A B G Fig. 4 135cm Fig. 2 1 2 Fig. 5 A B A B D F E F C C Fig. 3 Fig. 6