Stryker SV2 Maintenance Manual

Symbols Refer to instruction manual/booklet Operating instructions / Consult instructions for use General warning Caution Warning; crushing of hands Warning; crushing of feet Do not insert lift pole Headboard and footboard orientation Do not store items under the bed. Gatch positioning Catalogue number Serial number CE mark Manufacturer Mass of equipment with safe working load Safe working load Maximum patient weight Adult patient

www.stryker.com Symbols Direct current ~ Alternating current Dangerous voltage Unit provides terminal for connection of a potential equalization conductor. The potential equalization conductor provides direct connection between the unit and potential equalization busbar of the electrical installation. Protective Earth terminal IPX4 Protection from liquid splash Type B applied part In accordance with European Directive 2012/19/EU on Waste Electrical and Electronic Equipment (WEEE), this symbol indicates that the product must not be disposed of as unsorted municipal waste, but should be collected separately. Contact your local distributor for disposal information. See the maintenance manual for servicing instructions and recyclable components.

1 Table of Contents Warning/Caution/Note Definition ..................................................................................................................3 Summary of safety precautions....................................................................................................................4 Pinch points .......................................................................................................................................5 Preventive maintenance .............................................................................................................................6 Cleaning..................................................................................................................................................8 Preparing the product for cleaning..........................................................................................................8 Cleaning............................................................................................................................................8 Cleaning the siderails...........................................................................................................................9 Disinfecting............................................................................................................................................ 10 Troubleshooting...................................................................................................................................... 11 Quick reference replacement parts............................................................................................................. 14 Service ................................................................................................................................................. 57 Fowler (backrest) actuator replacement................................................................................................. 57 Gatch (legrest) actuator replacement.................................................................................................... 57 Head end lift actuator replacement ....................................................................................................... 58 Foot end lift actuator replacement ........................................................................................................ 59 Non-steer caster replacement.............................................................................................................. 61 Steer (head left) caster replacement..................................................................................................... 62 Fifth wheel replacement ..................................................................................................................... 64 Head end siderail gas cylinder replacement............................................................................................ 64 Foot end siderail gas cylinder replacement............................................................................................. 65 Lower leg section locking mechanism replacement .................................................................................. 66 Patient control pendant replacement..................................................................................................... 67 Nurse control pendant replacement ...................................................................................................... 67 Siderail control panel (inside and outside siderail) replacement .................................................................. 68 Control box replacement..................................................................................................................... 68 Battery replacement .......................................................................................................................... 69 Power cord replacement..................................................................................................................... 70 Head end siderail hoop replacement ..................................................................................................... 71 Foot end siderail hoop replacement ...................................................................................................... 72 Brake system ......................................................................................................................................... 73 Base and leg assembly............................................................................................................................. 76 Base and leg assembly with 5th wheel (option).............................................................................................. 78 Litter / frame assembly............................................................................................................................. 79 Bumper roller assembly............................................................................................................................ 81 Bed extender assembly ............................................................................................................................ 82 Hi-Lo actuators ....................................................................................................................................... 84 Control box and battery ............................................................................................................................ 85 Litter fowler (backrest) assembly................................................................................................................ 86 Litter seat assembly................................................................................................................................. 88 Litter gatch (legrest) assembly................................................................................................................... 89 Fowler (backrest) actuator ........................................................................................................................ 91 Gatch (legrest) actuator ........................................................................................................................... 92

www.stryker.com Table of Contents Siderail head end assembly....................................................................................................................... 93 Siderail foot end assembly ........................................................................................................................ 94 Siderail assembly.................................................................................................................................... 95 Siderail release latch assembly.................................................................................................................. 96 Headboard and footboard assembly............................................................................................................ 97 EMC information ..................................................................................................................................... 98 Warranty ............................................................................................................................................. 102 Recycling passports............................................................................................................................... 103

3 Warning/Caution/Note Definition The words WARNING, CAUTION, and NOTE carry special meanings and should be carefully reviewed. WARNING Alerts the reader about a situation which, if not avoided, could result in death or serious injury. It may also describe potential serious adverse reactions and safety hazards. CAUTION Alerts the reader of a potentially hazardous situation which, if not avoided, may result in minor or moderate injury to the user or patient or damage to the product or other property. This includes special care necessary for the safe and effective use of the device and the care necessary to avoid damage to a device that may occur as a result of use or misuse. Note: Provides special information to make maintenance easier or important instructions clearer.

www.stryker.com Summary of safety precautions Always read and strictly follow the warnings and cautions listed on this page. Service only by qualified personnel. WARNING • Do not clean, service, or perform maintenance while the product is in use. • Always power off and unplug the power cord before cleaning, servicing, or performing maintenance. • Always power off the product and unplug the power cord from the wall outlet when large spills occur near the circuit boards, cables, and motors. Remove the patient from the product, clean up the fluid, and have service personnel inspect the product. Fluids can cause unpredictable operation and decreased functionality of any electrical product. Do not return the product to service until it is completely dry and has been thoroughly tested for safe operation. • Do not spray cleaners directly onto the battery, control boxes, actuators, cables, or other electric equipment. • Do not use abrasive powder, steel wool, or similar materials that may damage the product surface. • Do not use Virex® TB for product disinfecting. • Do not use acid-based chemicals or flammable chemicals, such as gasoline, diesel, or acetone for cleaning purposes. • The cleaners and disinfectants must not be highly alkaline or acidic (pH value 6-8). • Do not directly spray or saturate the siderail control panel, patient control pendant, or nurse control pendant with cleaners. • Do not use sharp objects to clean the siderail control panel. • Always make sure to line the hex shaft with the hex in the caster. Test the caster to identify the direction of the brake. Damage may occur if you install the caster incorrectly. • Always make sure to line the hex shaft with the hex in the caster. Test the caster to identify the direction of the brake. Damage may occur if you install the caster incorrectly. CAUTION • Do not steam clean, pressure wash, ultrasonically clean, or immerse any part of the product in water. Exposure to water may damage the internal electric parts. These methods of cleaning are not recommended and may void this product’s warranty. • Always make sure that you wipe each product with clean water and thoroughly dry each product after cleaning. Some cleaning products are corrosive in nature and may cause damage to the product if you use them improperly. If you do not properly rinse and dry the product, you may leave a corrosive residue on the surface of the product that could cause premature corrosion of critical components. Failure to follow these cleaning instructions may void your warranty.

5 Summary of safety precautions Pinch points Figure 1: SV2 pinch points

www.stryker.com Preventive maintenance At a minimum, check all items listed during annual preventive maintenance for all Stryker Medical products. You may need to perform preventive maintenance checks more frequently based on your level of product usage. Remove product from service before performing preventive maintenance. Preventive maintenance should only be performed by trained or certified personnel. See the maintenance manual for servicing and maintenance instructions. Inspect the following items: All welds and all fasteners are secure Tubing or sheet metal for bends or breaks Casters are free of debris Casters are secure and swivel Casters lock securely by depressing the brake pedal Locking steer caster applies and releases Steer pedal latches Backrest operates Litter up and down operates Trendelenburg and Reverse Trendelenburg operates IV pole is intact and operating (optional) Accessory sleeves are not damaged or cracked Bed extender extends and locks (option) Headboard, footboard, and siderail panels for cracks or splits All covers are not damaged and do not have sharp edges Radiolucent backrest is clean and not cracked (option) Cassette holder is clean and not cracked (option) Underbed light operates CPR release operates Siderails move, latch, and stow All functionality on all control panels Batteries for replacement Batteries for corrosion at the terminals, cracking, expanded or bulging at the sides, or can no longer maintain a full charge Lower leg section moves, latches, and stows Pendants for any physical damage Power cord not worn or frayed Cables not worn or pinched All electrical connections tight All grounds secure to the frame Ground Impedance Check ( ≤ 0.2 Ohm) Leakage current: Normal Polarity, No Ground, L2 Active ( ≤ 300 µA) Leakage current: Normal Polarity, No Ground, No L2 (≤ 600 µA) Leakage current: Reverse Polarity, No Ground, L2 Active (≤ 300 µA) Leakage current: Reverse Polarity, no Ground, No L2 (≤ 600 µA) Enclosure is free from wear, tear, stresses and mechanical damage High potential test 1500 VAC (trip current not more than 10 mA) No rust or corrosion of parts Control boxes are not damaged or cracked Actuator functionality Labels for legibility, proper adherence, and integrity

www.stryker.com Cleaning Preparing the product for cleaning Cleaning and disinfecting are two separate processes. Clean before disinfecting to make sure that the cleaning agent is effective. To prepare the product for cleaning: 1. Raise the litter to its highest height. 2. Lock the siderail control panel and patient control pendant functions (see the operations manual for instructions on how to lock the patient functions). 3. Unplug the power cord from the wall outlet. 4. See the operations manual for instructions on how to store the power cord. 5. See the operations manual for instructions on how to apply the brakes. 6. Remove the mattress. Cleaning WARNING • Do not clean, service, or perform maintenance while the product is in use. • Always power off and unplug the power cord before cleaning, servicing, or performing maintenance. • Always power off the product and unplug the power cord from the wall outlet when large spills occur near the circuit boards, cables, and motors. Remove the patient from the product, clean up the fluid, and have service personnel inspect the product. Fluids can cause unpredictable operation and decreased functionality of any electrical product. Do not return the product to service until it is completely dry and has been thoroughly tested for safe operation. • Do not spray cleaners directly onto the battery, control boxes, actuators, cables, or other electric equipment. • Do not use abrasive powder, steel wool, or similar materials that may damage the product surface. • Do not use Virex® TB for product disinfecting. • Do not use acid-based chemicals or flammable chemicals, such as gasoline, diesel, or acetone for cleaning purposes. • Do not directly spray or saturate the siderail control panel, patient control pendant, or nurse control pendant with cleaners. • The cleaners and disinfectants must not be highly alkaline or acidic (pH value 6-8). CAUTION • Do not steam clean, pressure wash, ultrasonically clean, or immerse any part of the product in water. Exposure to water may damage the internal electric parts. These methods of cleaning are not recommended and may void this product’s warranty. • Always make sure that you wipe each product with clean water and thoroughly dry each product after cleaning. Some cleaning products are corrosive in nature and may cause damage to the product if you use them improperly. If you do not properly rinse and dry the product, you may leave a corrosive residue on the surface of the product that could cause premature corrosion of critical components. Failure to follow these cleaning instructions may void your warranty. To clean product surfaces: 1. Using a clean, soft, damp cloth, wipe product surfaces with a mild soap and water solution to remove foreign material. 2. Wipe product surfaces with a clean, dry cloth to remove any excess liquid or cleaning agent. 3. Dry thoroughly.

9 Cleaning Cleaning the siderails WARNING • Do not directly spray or saturate the siderail control panel, patient control pendant, or nurse control pendant with cleaners. • Do not use sharp objects to clean the siderail control panel. • Do not use abrasive powder, steel wool, or similar materials that may damage the product surface. • Do not use Virex® TB for product cleaning. • Do not use acid-based chemicals or flammable chemicals, such as gasoline, diesel, or acetone for cleaning purposes. To clean the siderails: 1. Raise the siderail. 2. Latch the siderail. 3. Use a clean, soft, damp cloth to wipe down the siderail and the siderail control panel. 4. Allow the siderail control panel to dry thoroughly.

www.stryker.com Disinfecting Suggested disinfectants: • Quaternary cleaners without glycol ethers (active ingredient - ammonium chloride) • Chlorinated bleach solution (5.25% - less than 1 part bleach to 100 parts water) • 70% Isopropyl alcohol Always follow the disinfectant’s instructions for appropriate contact time and rinsing requirements. Avoid oversaturation and make sure that the product does not stay wet longer than the chemical manufacturer’s guidelines for proper disinfecting. To disinfect the product: 1. Thoroughly clean and dry the product before you apply disinfectants. 2. Apply recommended disinfectant solution by spray or pre-soaked wipes Note: Make sure that you follow the disinfectant’s instructions for appropriate contact time and rinsing requirements. 3. To disinfect mechanisms, lift the backrest and leg rest up to the highest height. 4. Wipe product surfaces and mechanisms with a clean, dry cloth to remove any excess liquid or cleaning agent. 5. Allow the product to dry completely before returning to service.

11 Troubleshooting Problem Possible Cause Solution Bed does not operate 1. Power cable does not plug to the mains. 2. Power cable is damaged. 3. Nurse control unit or hand control unit may be locked. 4. Control box does not operate 1. Ensure power cable and plug are not damaged and then plug the power cable to the mains. 2. Replace the power cable by the authorized service personnel. 3. Nurse control Unit activation button should be checked. (On- off). Inspect the nurse control unit or hand control unit and make sure they are not locked. 4. Control box should be replaced, call the technical service. When the system operates, one of the actuators does not operate and control box gives a click sound 1. Actuator cable may be out of the control box socket. 2. Actuator cable is damaged. 3. Actuator is damaged; 4. CPR wire remains stuck; 5. Control box is damaged. 1. Check socket connections of the control box. 2. Actuator cable should be replaced, call the service center. 3. Actuator should be replaced, call the service center. 4. Inspect CPR wire and nut adjustment. 5. Control box should be replaced, call the service center. When the system operates, one of the actuators does not operate and control box does not give a click sound 1. Nurse control unit or hand control unit may be partly locked. 2. Control unit is damaged, 3. Control box is damaged. 1. Inspect nurse control unit or hand control and make sure they are not locked. 2. Unplug side rail control unit from the socket and check for function with the nurse control unit. If function is restored, their may be a problem with one of the control units. Call technical service. 3. Control box should be replaced, call the service center. Battery is possibly discharged and does not give click sound 1. Battery is completely discharged 2. Battery is damaged or expired. 1. Recharge the battery. 2. Battery should be replaced, call the service center. System operates but actuators move slowly Power is possibly disconnected and the bed operates by battery. 1. Power cable might have come out of the control panel; check it. 2. Check the connections of the power cable. 3. Check the socket.

www.stryker.com Troubleshooting Problem Possible Cause Solution 4. Recharge the battery, call the service center. Control box beeps while actuators are raised and actuators will not move in the downward direction Control box actuator position reference has been lost. 1. Unplug the power cord and turn off the battery. 2. Plug in the power cord and turn on the battery. 3. Run each upper actuator to its highest position. Failure Mode : Bed does not operate due to actuator failure or power request error. When a failure mode occurs and a key is activated the system will beep quickly, and if LEDs are used for locking functions on Nurse Control Unit, these will blink quickly, except when powering down on battery. Failure indications: 1) All Nurse Control Unit LEDs are blinking. 2) The CB6 buzzer beeps quickly if the handset is activated. 1. Actuator cables are unplugged. 2. Electrical short in a control cable (cable of control units or actuators). 3. If a function is activated but the actuator configuration doesn’t support the function. 4. Switch has failed in an actuator. 5. Control pendant (nurse or patient) or siderail control panel has failed. 6. Control box has failed. 1. Reset the failure mode. 2. a. Press and hold the Trendelenburg button (A) on the nurse control panel and the Autocontour up (B) on the patient control panel at the same time for five seconds. Note: The Trendelenburg and Autocontour up buttons are found on the opposite sides of the same siderail control panel. b. Press and hold the Backrest up (C) and Backrest down (D) buttons at the same time on the patient control pendant (option), or Autocontour up (E) and Trendelenburg (F) buttons at the same time on the nurse control pendant (option) for five seconds. 3. After five seconds, you will hear a buzzer. 4. Keep pressing buttons until the buzzer stops. 5. LEDs will stop blinking. 6. Press the CPR button in to zero all the actuators. 7. Failure mode does not result in a position lost. Make sure that the system is in a safe position after resetting the failure mode. 8. Continue to troubleshoot through possible causes until corrected.

www.stryker.com Quick reference replacement parts These parts are currently available for purchase. Call Stryker Customer Service: + 90 (352) 321 43 00 (pbx) for availability and pricing. Kit name Number Kit contents Number Name Quantity Actuator kit, Fowler (backrest) YM-KIT-100049 HM-11-31 Ø 10 rue clip 2 HM-12-FTR010 Ø14xØ10x65 mm 2 HM-17-303 4000 N LA40 QR 215 mm actuator 1 YM-HM-02-027 Actuator pin fixing bush 1 Actuator kit, gatch (legrest) YM-KIT-100051 HM-02-283 2 mm plastic washer (10 mm plastic washer) mould NO 34 2 HM-11-31 Ø10 rue clip 3 HM-12-FTR010 Ø14xØ10x65 mm 1 HM-12-FTR009 Actuator calf pin 10x96, 5 mm 1 HM-17-305 6000 N LA40 100 mm stroke actuator 1 YM-HM-02-070 5 mm PLS washer (inside diameter 10 mm washer) 2 YM-HM-02-287 10*14 mm PLS washer mould NO 36 2 YM-HM-02-027 Actuator pin fixing bush 1 Actuator kit, lift YM-KIT-100050 HM-11-31 Ø10 rue clip 2 HM-12-FTR010 Ø14xØ10x65 mm actuator connection pin 1 HM-12-FTR011 10x41 mm actuator connection pin 1 HM-17-304 J13205-8000 N LA40 150 mm stroke actuator 1 YM-HM-02-027 Actuator pin fixing bush 1 Battery replacement kit YM-KIT-100001 HM-05-043 M5*20 imbus bolt 4 HM-07-22 M6 iron washer (small) 4 HM-08-04 M5 fibered nut 4 HM-16-03 Ø25 clips (UB250C- N 245x4,6 cable connector) 2

15 Quick reference replacement parts Kit name Number Kit contents Number Name Quantity HM-17-16 BA1812-1300-000 Linak CB6 battery 1 Brake pedal replacement kit, left YM-KIT-100082 YM-SV2PDL-001-BY Pedal sheet weld assembly 1 YM-HM-02-023 Pedal plastic body 1 HM-20-424 Pedal label-left 1 HM-20-423 Pedal label-right 1 HM-07-22 M6 iron washer (small) 1 HM-08-05 M6 fibered nut 1 HM-12-905 Transfer laser cut part bushing (bronz) 1 HM-07-09 Special pedal washer 2 HM-06-86 Ø6 x 16 cross recessed raised cheese head screws 2 HM-11-34 Ø13 rue segman 1 HM-06-001 M6 x 25 mushroom head square neck bolt 1 Brake pedal replacement kit, right YM-KIT-100083 YM-SV2PDL-001-BY Pedal sheet weld assembly 1 YM-HM-02-023 Pedal plastic body 1 HM-20-423 Pedal label-right 1 HM-07-22 M6 iron washer (small) 1 HM-08-05 M6 fibered nut 1 HM-12-905 Transfer laser cut part bushing (bronz) 1 HM-07-09 Special pedal washer 2 HM-06-86 Ø6 x 16 cross recessed raised cheese head screws 2 HM-11-34 Ø13 rue segman 1 HM-06-001 M6 x 25 mushroom head square neck bolt 1 Caster kit, dual wheel no steer lock, antistatic (150 mm) YM-KIT-100041 HM-01-86 2946USP150R36- 32S30 D RAL 9002 4XM6 TENTE 150 mm double no steer 1

www.stryker.com Quick reference replacement parts Kit name Number Kit contents Number Name Quantity lock antistatic caster (Stryker) HM-05-106 M6*16 imbus bolt 2 HM-09-30 M6 toothed washer (DIN 6797 A) 2 HM-11-34 Ø13 rue clip 2 YM-HM-02-71 12 thick PLS washer DMR071 2 YM-HM-02-299 50*50 caster profile cap PLS (lower chasis PLS) 51 mould 1 HM-11-10 11 mm Snap ring (lipper) KMS starlock push on BV/6706 fastener 1 Caster kit, dual wheel no steer lock, not antistatic (150 mm) YM-KIT-100042 HM-01-26 2946UAP150R36- 32S30 D RAL 9002 4XM6 TENTE 150 mm double no steer lock not antistatic caster (Stryker) 1 HM-05-106 M6*16 imbus bolt 2 HM-09-30 M6 toothed washer (DIN 6797 A) 2 HM-11-34 Ø13 rue clip 2 YM-HM-02-71 12 thick PLS washer DMR071 2 YM-HM-02-299 50*50 caster profile cap PLS (lower chasis PLS) 51 mould 1 HM-11-10 11 mm Snap ring (lipper) KMS starlock push on BV/6706 fastener 1 Caster kit, Ø=150 dual-steer lock, not antistatic (150 mm) YM-KIT-100043 HM-01-87 Ø=150 dual-Stryker cap-steer lock-not antistatic- 2944UAP150R36- 32S30 1 HM-05-106 M6*16 imbus bolt 2 HM-09-30 M6 toothed washer (DIN 6797 A) 2 HM-11-34 Ø13 rue clip 2

17 Quick reference replacement parts Kit name Number Kit contents Number Name Quantity YM-HM-02-71 12 thick PLS washer DMR071 2 YM-HM-02-299 50*50 caster profile cap PLS (lower chasis PLS) 51 mould 1 HM-11-10 11 mm Snap ring (lipper) KMS starlock push on BV/6706 fastener 1 Caster kit, single wheel no steer lock, not antistatic YM-KIT-100044 HM-01-54 2046UAP150R36- 32S30 150 mm no steer lock not antistatic single caster 1 HM-05-106 M6*16 imbus bolt 2 HM-09-30 M6 toothed washer (DIN 6797 A) 2 HM-11-34 Ø13 rue clip 2 YM-HM-02-71 12 thick PLS washer DMR071 2 YM-HM-02-299 50*50 caster profile cap PLS (lower chasis PLS) 51 mould 1 HM-11-10 11 mm Snap ring (lipper) KMS starlock push on BV/6706 fastener 1 Caster kit, Ø 150 integral no steer lock, no antistatic wheel YM-KIT-100045 HM-01-80 Ø150 integral no steer lock, no antistatic wheel- 1046UAP150R36- 32S30 1 HM-05-106 M6*16 imbus bolt 2 HM-09-30 M6 toothed washer (DIN 6797 A) 2 HM-11-34 Ø13 rue clip 2 YM-HM-02-71 12 thick PLS washer DMR071 2 YM-HM-02-299 50*50 caster profile cap PLS (lower chasis PLS) 51 mould 1 HM-11-10 11 mm Snap ring (lipper) KMS starlock 1

www.stryker.com Quick reference replacement parts Kit name Number Kit contents Number Name Quantity push on BV/6706 fastener Caster kit, Ø 150 no steer lock, antistatic single YM-KIT-100046 HM-01-83 Ø150 integral, no steer lock, antistatic single caster- 2046XSX150R36- 32S30 1 HM-05-106 M6*16 imbus bolt 2 HM-09-30 M6 toothed washer (DIN 6797 A) 2 HM-11-34 Ø13 rue clip 2 YM-HM-02-71 12 thick PLS washer DMR071 2 YM-HM-02-299 50*50 caster profile cap PLS (lower chasis PLS) 51 mould 1 HM-11-10 11 mm Snap ring (lipper) KMS starlock push on BV/6706 fastener 1 Caster kit, Ø 150 steer lock, antistatic wheel YM-KIT-100047 HM-01-83 Ø150 integral steer lock, antistatic wheel- 1044XSP150R36- 32S30 1 HM-05-106 M6*16 imbus bolt 2 HM-09-30 M6 toothed washer (DIN 6797 A) 2 HM-11-34 Ø13 rue clip 2 YM-HM-02-71 12 thick PLS washer DMR071 2 YM-HM-02-299 50*50 caster profile cap PLS (lower chasis PLS) 51 mould 1 HM-11-10 11 mm Snap ring (lipper) KMS starlock push on BV/6706 fastener 1 Caster kit, Ø 150 steer lock, not antistatic single YM-KIT-100048 HM-01-84 Ø150 integral, steer lock, not antistatic single caster- 2044UAP150R36- 32S30 1 HM-05-106 M6*16 imbus bolt 2

19 Quick reference replacement parts Kit name Number Kit contents Number Name Quantity HM-09-30 M6 toothed washer (DIN 6797 A) 2 HM-11-34 Ø13 rue clip 2 YM-HM-02-71 12 thick PLS washer DMR071 2 YM-HM-02-299 50*50 caster profile cap PLS (lower chasis PLS) 51 mould 1 HM-11-10 11 mm Snap ring (lipper) KMS starlock push on BV/6706 fastener 1 Fifth wheel assembly kit YM-KIT-100084 YM-5TKR-001 5.wheel assembly group 1 YM-04-142-BY 5.wheel-base frame connection sheet 2 HM-07-22 M6 steel washer (small) 4 HM-05-041 M6*30 hexagon socket button head screw 4 HM-12-004 Ø8 perforated pin 1 HM-11-35 Ø8 rue clip 1 YM-HM-02-026 8,5 x 16 x 2,2 mm plastic washer 1 Fifth wheel replacement kit YM-KIT-100085 HM-01-32 Tente PJO100x32- Ø12 - wheel 1 YM-HM-02-030 5th wheel - wheel washer 2 HM-07-03 M8 steel washer 2 HM-08-06 M8 self-lock hex nut 1 HM-05-048 M8*60 hexagon socket button head screw 1 Control box replacement kit YM-KIT-100040 HM-05-010 M6*50 steel bolt 1 HM-07-01 M6 metal standard washer (large) 1/4 washer 2 HM-08-05 M6 fibered nut 1 HM-17-373 SV2 control box CB6777-00 1

www.stryker.com Quick reference replacement parts Kit name Number Kit contents Number Name Quantity Footboard kit with logo, dark blue YM-KIT-100033 YM-FTRBASLIK-MN1 Future polypropylene bed head and foot assembly 1 HM-20-870 SV2 dark blue (Stryker) foot end bed head color sticker with Stryker logo 1 HM-22-1780 3M primer 94 handkerchief 1 Footboard- headboard kit YM-KIT-100005 YM-FTRBASLIK-MN1 Future polypropylene head and foot assembly 1 HM-22-1780 3M primer 94 handkerchief 1 Headboard kit, dark blue YM-KIT-100005-B YM-FTRBASLIK-MN1 Future polypropylene head and foot assembly 1 HM-22-1780 3M primer 94 handkerchief 1 HM-20-871 SV2 dark blue (Stryker) head color sticker 1 Headboard kit, dark wood YM-KIT-100005-D YM-FTRBASLIK-MN1 Future polypropylene head and foot assembly 1 HM-22-1780 3M primer 94 handkerchief 1 HM-20-763 08 dark wood future bed head color 1 Headboard kit, light wood YM-KIT-100005-L YM-FTRBASLIK-MN1 Future polypropylene head and foot assembly 1 HM-22-1780 3M primer 94 handkerchief 1 HM-20-753 06 light wood future bed head color 1 Headboard kit, wood YM-KIT-100005-W YM-FTRBASLIK-MN1 Future polypropylene head and foot assembly 1 HM-22-1780 3M primer 94 handkerchief 1 HM-20-758 07 wood color future bed head color 1 Label kit, dark blue YM-KIT-100032 HM-20-870 SV2 dark blue (Stryker) foot end bed 1

21 Quick reference replacement parts Kit name Number Kit contents Number Name Quantity head color sticker with Stryker logo HM-20-871 SV2 dark blue (Stryker) head color sticker 1 HM-20-872 SV2 dark blue (Stryker) upper right siderail color sticker 1 HM-20-873 SV2 dark blue (Stryker) upper left siderail color sticker 1 HM-20-874 SV2 dark blue (Stryker) lower right siderail color sticker 1 HM-20-875 SV2 dark blue (Stryker) lower left siderail color sticker 1 HM-22-1780 3M primer 94 handkerchief 6 Label kit, dark wood YM-KIT-100036 HM-20-759 08 dark wood future siderail color, back right 1 HM-20-760 08 dark wood future siderail color, back left 1 HM-20-761 08 dark wood future siderail color, foot right 1 HM-20-762 08 dark wood future siderail color, foot left 1 HM-20-763 08 dark wood future bed head color 1 HM-22-1780 3M primer 94 handkerchief 6 Label kit, light wood YM-KIT-100034 HM-20-749 06 light wood future siderail color, back right 1 HM-20-750 06 light wood future siderail color, back left 1 HM-20-751 06 light wood future siderail color, foot right 1 HM-20-752 06 light wood future siderail color, foot left 1

www.stryker.com Quick reference replacement parts Kit name Number Kit contents Number Name Quantity HM-20-753 06 light wood future bed head color 1 HM-22-1780 3M primer 94 handkerchief 6 Label kit, wood YM-KIT-100035 HM-20-754 07 wood color future siderail color, back right 1 HM-20-755 07 wood color future siderail color, back left 1 HM-20-756 07 wood color future siderail color, foot right 1 HM-20-757 07 wood color future siderail color, foot left 1 HM-20-758 07 wood color future bed head color 1 HM-22-1780 3M primer 94 handkerchief 6 SV2 nurse control pendant kit YM-KIT-100060 HM-16-03 Ø25 clips (UB250C- N 245x4,6 cable connector) 5 HM-17-103 0964541 Linak supervisor spiral cable 1 HM-17-313 AC0076-00 Attendance control (hand held for nurse) 1 HM-17-186 00911045 ACO snap ring 1 Power cord replacement kit, type B (Japan) YM-KIT-100061 HM-16-03 Ø25 clips (UB250C- N 245x4,6 cable connector) 5 YM-HM-02-040 Ø7 Plastic cable holder 1 HM-06-09 Ø3,9 x 25 Countersunk milling head self drilling screw 2 HM-17-020 Japan, type B, straight/black 1 Power cord replacement kit, type B (North/South America) YM-KIT-100062 HM-16-03 Ø25 clips (UB250C- N 245x4,6 cable connector) 5

23 Quick reference replacement parts Kit name Number Kit contents Number Name Quantity YM-HM-02-041 Ø8,5 Plastic cable holder 1 HM-06-09 Ø3,9 x 25 Countersunk milling head self drilling screw 2 HM-17-021 Type B SJT North/South America 1 Power cord replacement kit, type 1 straight orange (Australia) YM-KIT-100063 YM-HM-02-040 Ø7 Plastic cable holder 1 HM-06-09 Ø3,9 x 25 Countersunk milling head self drilling screw 2 HM-17-017 Type 1, Australia straight orange 1 Power cord replacement kit, type B coiled orange (North/South America) YM-KIT-100064 HM-16-03 Ø25 clips (UB250C- N 245x4,6 cable connector) 5 YM-HM-02-041 Ø8,5 Plastic cable holder 1 HM-06-09 Ø3,9 x 25 Countersunk milling head self drilling screw 2 HM-17-023 Type B, SJT North/South America coiled orange 1 Power cord replacement kit, type B (Taiwan) YM-KIT-100065 HM-16-03 Ø25 clips (UB250C- N 245x4,6 cable connector) 5 YM-HM-02-040 Ø7 Plastic cable holder 1 HM-06-09 Ø3,9 x 25 Countersunk milling head self drilling screw 2 HM-17-024 Type B Taiwan 1 Power cord replacement kit, type B coiled (Philippines) YM-KIT-100066 HM-16-03 Ø25 clips (UB250C- N 245x4,6 cable connector) 5 YM-HM-02-041 Ø8,5 Plastic cable holder 1 HM-06-09 Ø3,9 x 25 Countersunk milling 2

www.stryker.com Quick reference replacement parts Kit name Number Kit contents Number Name Quantity head self drilling screw HM-17-025 Philippines coiled power cord 1 Power cord replacement kit, type D straight (India) YM-KIT-100067 HM-16-03 Ø25 clips (UB250C- N 245x4,6 cable connector) 5 YM-HM-02-040 Ø7 Plastic cable holder 1 HM-06-09 Ø3,9 x 25 Countersunk milling head self drilling screw 2 HM-17-026 India type D straight/black 1 Power cord replacement kit, type E/F schuko straight (Europe) YM-KIT-100068 HM-16-03 Ø25 clips (UB250C- N 245x4,6 cable connector) 5 YM-HM-02-040 Ø7 Plastic cable holder 1 HM-06-09 Ø3,9 x 25 Countersunk milling head self drilling screw 2 HM-17-027 Europe/schuko straight/black 1 Power cord replacement kit, type E/F coiled black (Korean) YM-KIT-100069 HM-16-03 Ø25 clips (UB250C- N 245x4,6 cable connector) 5 YM-HM-02-040 Ø7 Plastic cable holder 1 HM-06-09 Ø3,9 x 25 Countersunk milling head self drilling screw 2 HM-17-028 Korean, coiled black 1 Power cord replacement kit, type E/F schuko coiled orange (Europe) YM-KIT-100070 HM-16-03 Ø25 clips (UB250C- N 245x4,6 cable connector) 5 YM-HM-02-040 Ø7 Plastic cable holder 1 HM-06-09 Ø3,9 x 25 Countersunk milling head self drilling screw 2

25 Quick reference replacement parts Kit name Number Kit contents Number Name Quantity HM-17-029 Europe/schuko coiled orange 1 Power cord replacement kit, type G coiled orange (United Kingdom) YM-KIT-100071 HM-16-03 Ø25 clips (UB250C- N 245x4,6 cable connector) 5 YM-HM-02-040 Ø7 Plastic cable holder 1 HM-06-09 Ø3,9 x 25 Countersunk milling head self drilling screw 2 HM-17-032 Type G United Kingdom coiled orange 1 Power cord replacement kit, type H straight black (Israel) YM-KIT-100072 HM-16-03 Ø25 clips (UB250C- N 245x4,6 cable connector) 5 YM-HM-02-040 Ø7 Plastic cable holder 1 HM-06-09 Ø3,9 x 25 Countersunk milling head self drilling screw 2 HM-17-033 Type H Israel, straight black 1 Power cord replacement kit, type I straight black (Argentina) YM-KIT-100073 HM-16-03 Ø25 clips (UB250C- N 245x4,6 cable connector) 5 YM-HM-02-040 Ø7 Plastic cable holder 1 HM-06-09 Ø3,9 x 25 Countersunk milling head self drilling screw 2 HM-17-034 Type I Argentina straight black 1 Power cord replacement kit, type I straight black (Australia) YM-KIT-100074 HM-16-03 Ø25 clips (UB250C- N 245x4,6 cable connector) 5 YM-HM-02-040 Ø7 Plastic cable holder 1 HM-06-09 Ø3,9 x 25 Countersunk milling head self drilling screw 2

www.stryker.com Quick reference replacement parts Kit name Number Kit contents Number Name Quantity HM-17-035 Type I Australia straight black 1 Power cord replacement kit, type I coiled orange (Argentina) YM-KIT-100075 HM-16-03 Ø25 clips (UB250C- N 245x4,6 cable connector) 5 YM-HM-02-040 Ø7 Plastic cable holder 1 HM-06-09 Ø3,9 x 25 Countersunk milling head self drilling screw 2 HM-17-037 Type I Argentina coiled orange 1 Power cord replacement kit, type J straight black (Switzerland) YM-KIT-100076 HM-16-03 Ø25 clips (UB250C- N 245x4,6 cable connector) 5 YM-HM-02-040 Ø7 Plastic cable holder 1 HM-06-09 Ø3,9 x 25 Countersunk milling head self drilling screw 2 HM-17-038 Type J Switzerland straight black 1 Power cord replacement kit, type K straight black (Denmark) YM-KIT-100077 HM-16-03 Ø25 clips (UB250C- N 245x4,6 cable connector) 5 YM-HM-02-040 Ø7 Plastic cable holder 1 HM-06-09 Ø3,9 x 25 Countersunk milling head self drilling screw 2 HM-17-039 Type K Denmark straight black 1 Power cord replacement kit, type L straight black (Italy) YM-KIT-100078 HM-16-03 Ø25 clips (UB250C- N 245x4,6 cable connector) 5 YM-HM-02-040 Ø7 Plastic cable holder 1 HM-06-09 Ø3,9 x 25 Countersunk milling head self drilling screw 2 HM-17-040 Type L Italy straight black 1

27 Quick reference replacement parts Kit name Number Kit contents Number Name Quantity Power cord replacement kit, type M straight black (South Africa) YM-KIT-100079 HM-16-03 Ø25 clips (UB250C- N 245x4,6 cable connector) 5 YM-HM-02-040 Ø7 Plastic cable holder 1 HM-06-09 Ø3,9 x 25 Countersunk milling head self drilling screw 2 HM-17-041 Type M South Africa, straight black 1 Power cord replacement kit, type N straight black (Brazil) YM-KIT-100080 HM-16-03 Ø25 clips (UB250C- N 245x4,6 cable connector) 5 YM-HM-02-040 Ø7 Plastic cable holder 1 HM-06-09 Ø3,9 x 25 Countersunk milling head self drilling screw 2 HM-17-042 Type N Brazil straight black 1 Internal universal power cord replacement kit YM-KIT-100081 HM-16-03 Ø25 clips (UB250C- N 245x4,6 cable connector) 5 HM-10-018 P-clamp 1 HM-06-121 M4, 2*19 mm self tapping screw 1 HM-17-043 Internal universal power cord 1 Roller bumper replacement kit YM-KIT-100009 HM-02-354 Future bumper 1 HM-11-26 5 mm C shape snap ring DIN 6799 1 HM-12-FTR001 12-FT001 future bumper pin 1 Backrest siderail gas cylinder kit YM-KIT-100010 HM-11-18 Q8 capped snap ring (DT/6671/43A) 2 HM-12-146 12-146 8 x 31 mm side rail pin 1 HM-18-27 Future side rail shock absorber 640015004 1 HM-05-018 M8*90 half thread steel bolt 1

www.stryker.com Quick reference replacement parts Kit name Number Kit contents Number Name Quantity YM-HM-02-418 Future side rail shock absorber PLS 2 HM-07-03 M8 iron washer 2 HM-08-06 M8 fibered nut 1 HM-20-557 Ø15 clips 1 Footrest siderail gas cylinder kit YM-KIT-100038 HM-11-18 Q8 capped snap ring (DT/6671/43A) 2 HM-12-146 12-146 8 x 31 mm side rail pin 1 HM-18-27 Future side rail shock absorber 640015004 1 HM-11-05 6 mm C shape snap ring DIN 6799 1 HM-02-283 2 mm plastic washer (10 mm plastic washer) mould NO 34 2 HM-12-FTR005 Shock absorber connection pin 1 Siderail kit, foot end left YM-KIT-100052 YM-02-142-MN1 SV2 Left foot siderail assembly 1 HM-12-FTR005 12-FTR005 shock absorber connection pin 1 HM-02-283 2 mm plastic washer (10 mm plastic washer) mould NO 34 6 HM-11-05 6 mm C shape snap ring DIN 6799 1 HM-11-19 Q10 capped snap ring (DT/6668/44A) 2 HM-11-31 Ø10 rue clip 2 HM-12-005 10x123,5 mm siderail pin 1 HM-12-145 12-145 10 x 305 mm siderail pin 1 YM-HM-02-028 Side board lock plastic-long 2 YM-HM-02-029 Side board lock plastic-short 1 HM-22-1780 3M primer 94 handkerchief 1

29 Quick reference replacement parts Kit name Number Kit contents Number Name Quantity HM-20-394 Warning, crushing of hands label 1 Siderail kit, foot end left, dark blue YM-KIT-100052-B YM-02-142-MN1 SV2 Left foot siderail assembly 1 HM-12-FTR005 12-FTR005 shock absorber connection pin 1 HM-02-283 2 mm plastic washer (10 mm plastic washer) mould NO 34 6 HM-11-05 6 mm C shape snap ring DIN 6799 1 HM-11-19 Q10 capped snap ring (DT/6668/44A) 2 HM-11-31 Ø10 rue clip 2 HM-12-005 10x123,5 mm siderail pin 1 HM-12-145 12-145 10 x 305 mm siderail pin 1 YM-HM-02-028 Side board lock plastic-long 2 YM-HM-02-029 Side board lock plastic-short 1 HM-22-1780 3M primer 94 handkerchief 1 HM-20-394 Warning, crushing of hands label 1 HM-20-875 SV2 dark blue (Stryker) lower left siderail color sticker 1 Siderail kit, foot end left, dark wood YM-KIT-100052-D YM-02-142-MN1 SV2 Left foot siderail assembly 1 HM-12-FTR005 12-FTR005 shock absorber connection pin 1 HM-02-283 2 mm plastic washer (10 mm plastic washer) mould NO 34 6 HM-11-05 6 mm C shape snap ring DIN 6799 1 HM-11-19 Q10 capped snap ring (DT/6668/44A) 2

www.stryker.com Quick reference replacement parts Kit name Number Kit contents Number Name Quantity HM-11-31 Ø10 rue clip 2 HM-12-005 10x123,5 mm siderail pin 1 HM-12-145 12-145 10 x 305 mm siderail pin 1 YM-HM-02-028 Side board lock plastic-long 2 YM-HM-02-029 Side board lock plastic-short 1 HM-22-1780 3M primer 94 handkerchief 1 HM-20-394 Warning, crushing of hands label 1 HM-20-762 08 dark wood future siderail color foot left 1 Siderail kit, foot end left, light wood YM-KIT-100052-L YM-02-142-MN1 SV2 Left foot siderail assembly 1 HM-12-FTR005 12-FTR005 shock absorber connection pin 1 HM-02-283 2 mm plastic washer (10 mm plastic washer) mould NO 34 6 HM-11-05 6 mm C shape snap ring DIN 6799 1 HM-11-19 Q10 capped snap ring (DT/6668/44A) 2 HM-11-31 Ø10 rue clip 2 HM-12-005 10x123,5 mm siderail pin 1 HM-12-145 12-145 10 x 305 mm siderail pin 1 YM-HM-02-028 Side board lock plastic-long 2 YM-HM-02-029 Side board lock plastic-short 1 HM-22-1780 3M primer 94 handkerchief 1 HM-20-394 Warning, crushing of hands label 1 HM-20-752 06 light wood future siderail color foot left 1

31 Quick reference replacement parts Kit name Number Kit contents Number Name Quantity Siderail kit, foot end left, wood YM-KIT-100052-W YM-02-142-MN1 SV2 Left foot siderail assembly 1 HM-12-FTR005 12-FTR005 shock absorber connection pin 1 HM-02-283 2 mm plastic washer (10 mm plastic washer) mould NO 34 6 HM-11-05 6 mm C shape snap ring DIN 6799 1 HM-11-19 Q10 capped snap ring (DT/6668/44A) 2 HM-11-31 Ø10 rue clip 2 HM-12-005 10x123,5 mm siderail pin 1 HM-12-145 12-145 10 x 305 mm siderail pin 1 YM-HM-02-028 Side board lock plastic-long 2 YM-HM-02-029 Side board lock plastic-short 1 HM-22-1780 3M primer 94 handkerchief 1 HM-20-394 Warning, crushing of hands label 1 HM-20-757 07 wood color future siderail color foot left 1 Siderail kit, foot end right YM-KIT-100053 YM-02-144-MN1 SV2 Right foot siderail assembly 1 HM-12-FTR005 12-FTR005 shock absorber connection pin 1 HM-02-283 2 mm plastic washer (10 mm plastic washer) mould NO 34 6 HM-11-05 6 mm C shape snap ring DIN 6799 1 HM-11-19 Q10 capped snap ring (DT/6668/44A) 2 HM-11-31 Ø10 rue clip 2

www.stryker.com Quick reference replacement parts Kit name Number Kit contents Number Name Quantity HM-12-005 10x123,5 mm siderail pin 1 HM-12-145 12-145 10 x 305 mm siderail pin 1 YM-HM-02-028 Side board lock plastic-long 2 YM-HM-02-029 Side board lock plastic-short 1 HM-22-1780 3M primer 94 handkerchief 1 HM-20-394 Warning, crushing of hands label 1 Siderail kit, foot end right, dark blue YM-KIT-100053-B YM-02-144-MN1 SV2 Right foot siderail assembly 1 HM-12-FTR005 12-FTR005 shock absorber connection pin 1 HM-02-283 2 mm plastic washer (10 mm plastic washer) mould NO 34 6 HM-11-05 6 mm C shape snap ring DIN 6799 1 HM-11-19 Q10 capped snap ring (DT/6668/44A) 2 HM-11-31 Ø10 rue clip 2 HM-12-005 10x123,5 mm siderail pin 1 HM-12-145 12-145 10 x 305 mm siderail pin 1 YM-HM-02-028 Side board lock plastic-long 2 YM-HM-02-029 Side board lock plastic-short 1 HM-22-1780 3M primer 94 handkerchief 1 HM-20-394 Warning, crushing of hands label 1 HM-20-874 SV2 dark blue (Stryker) lower left siderail color sticker 1 Siderail kit, foot end right, dark wood YM-KIT-100053-D YM-02-144-MN1 SV2 Right foot siderail assembly 1

33 Quick reference replacement parts Kit name Number Kit contents Number Name Quantity HM-12-FTR005 12-FTR005 shock absorber connection pin 1 HM-02-283 2 mm plastic washer (10 mm plastic washer) mould NO 34 6 HM-11-05 6 mm C shape snap ring DIN 6799 1 HM-11-19 Q10 capped snap ring (DT/6668/44A) 2 HM-11-31 Ø10 rue clip 2 HM-12-005 10x123,5 mm siderail pin 1 HM-12-145 12-145 10 x 305 mm siderail pin 1 YM-HM-02-028 Side board lock plastic-long 2 YM-HM-02-029 Side board lock plastic-short 1 HM-22-1780 3M primer 94 handkerchief 1 HM-20-394 Warning, crushing of hands label 1 HM-20-761 08 dark wood future siderail color foot right 1 Siderail kit, foot end right, light wood YM-KIT-100053-L YM-02-144-MN1 SV2 Right foot siderail assembly 1 HM-12-FTR005 12-FTR005 shock absorber connection pin 1 HM-02-283 2 mm plastic washer (10 mm plastic washer) mould NO 34 6 HM-11-05 6 mm C shape snap ring DIN 6799 1 HM-11-19 Q10 capped snap ring (DT/6668/44A) 2 HM-11-31 Ø10 rue clip 2 HM-12-005 10x123,5 mm siderail pin 1

www.stryker.com Quick reference replacement parts Kit name Number Kit contents Number Name Quantity HM-12-145 12-145 10 x 305 mm siderail pin 1 YM-HM-02-028 Side board lock plastic-long 2 YM-HM-02-029 Side board lock plastic-short 1 HM-22-1780 3M primer 94 handkerchief 1 HM-20-394 Warning, crushing of hands label 1 HM-20-751 06 light wood future siderail color foot right 1 Siderail kit, foot end right, wood YM-KIT-100053-W YM-02-144-MN1 SV2 Right foot siderail assembly 1 HM-12-FTR005 12-FTR005 shock absorber connection pin 1 HM-02-283 2 mm plastic washer (10 mm plastic washer) mould NO 34 6 HM-11-05 6 mm C shape snap ring DIN 6799 1 HM-11-19 Q10 capped snap ring (DT/6668/44A) 2 HM-11-31 Ø10 rue clip 2 HM-12-005 10x123,5 mm siderail pin 1 HM-12-145 12-145 10 x 305 mm siderail pin 1 YM-HM-02-028 Side board lock plastic-long 2 YM-HM-02-029 Side board lock plastic-short 1 HM-22-1780 3M primer 94 handkerchief 1 HM-20-394 Warning, crushing of hands label 1 HM-20-756 07 wood color future siderail color foot right 1

35 Quick reference replacement parts Kit name Number Kit contents Number Name Quantity Siderail kit, head end left with unit YM-KIT-100054 YM-02-141-MN2 SV2 Back left siderail assembly with unit 1 HM-22-1780 3M primer 94 handkerchief 1 HM-02-283 2 mm plastic washer (10 mm plastic washer) mould NO 34 4 HM-11-19 Q10 capped snap ring (DT/6668/44A) 2 HM-12-005 10x123,5 mm siderail pin 1 HM-12-145 12-145 10 x 305 mm siderail pin 1 YM-HM-02-418 Future siderail shock absorber PLS 2 HM-05-018 M8*90 half thread steel bolt 1 HM-20-557 Ø15 clips 5 HM-07-03 M8 iron washer 2 HM-08-06 M8 fibered nut 1 HM-11-31 Ø10 rue clip 2 YM-HM-02-028 Side board lock plastic-long 2 YM-HM-02-029 Side board lock plastic-short 1 HM-20-394 Warning, crushing of hands label 1 Siderail kit, head end left with unit, dark blue YM-KIT-100054-B YM-02-141-MN2 SV2 Back left siderail assembly with unit 1 HM-22-1780 3M primer 94 handkerchief 1 HM-02-283 2 mm plastic washer (10 mm plastic washer) mould NO 34 4 HM-11-19 Q10 capped snap ring (DT/6668/44A) 2 HM-12-005 10x123,5 mm siderail pin 1 HM-12-145 12-145 10 x 305 mm siderail pin 1

www.stryker.com Quick reference replacement parts Kit name Number Kit contents Number Name Quantity YM-HM-02-418 Future siderail shock absorber PLS 2 HM-05-018 M8*90 half thread steel bolt 1 HM-20-557 Ø15 clips 5 HM-07-03 M8 iron washer 2 HM-08-06 M8 fibered nut 1 HM-11-31 Ø10 rue clip 2 YM-HM-02-028 Side board lock plastic-long 2 YM-HM-02-029 Side board lock plastic-short 1 HM-20-394 Warning, crushing of hands label 1 HM-20-873 SV2 dark blue (Stryker) upper left siderail color sticker 1 Siderail kit, head end left with unit, dark wood YM-KIT-100054-D YM-02-141-MN2 SV2 Back left siderail assembly with unit 1 HM-22-1780 3M primer 94 handkerchief 1 HM-02-283 2 mm plastic washer (10 mm plastic washer) mould NO 34 4 HM-11-19 Q10 capped snap ring (DT/6668/44A) 2 HM-12-005 10x123,5 mm siderail pin 1 HM-12-145 12-145 10 x 305 mm siderail pin 1 YM-HM-02-418 Future siderail shock absorber PLS 2 HM-05-018 M8*90 half thread steel bolt 1 HM-20-557 Ø15 clips 5 HM-07-03 M8 iron washer 2 HM-08-06 M8 fibered nut 1 HM-11-31 Ø10 rue clip 2 YM-HM-02-028 Side board lock plastic-long 2

37 Quick reference replacement parts Kit name Number Kit contents Number Name Quantity YM-HM-02-029 Side board lock plastic-short 1 HM-20-394 Warning, crushing of hands label 1 HM-20-760 08 dark wood future siderail color back left 1 Siderail kit, head end left with unit, light wood YM-KIT-100054-L YM-02-141-MN2 SV2 Back left siderail assembly with unit 1 HM-22-1780 3M primer 94 handkerchief 1 HM-02-283 2 mm plastic washer (10 mm plastic washer) mould NO 34 4 HM-11-19 Q10 capped snap ring (DT/6668/44A) 2 HM-12-005 10x123,5 mm siderail pin 1 HM-12-145 12-145 10 x 305 mm siderail pin 1 YM-HM-02-418 Future siderail shock absorber PLS 2 HM-05-018 M8*90 half thread steel bolt 1 HM-20-557 Ø15 clips 5 HM-07-03 M8 iron washer 2 HM-08-06 M8 fibered nut 1 HM-11-31 Ø10 rue clip 2 YM-HM-02-028 Side board lock plastic-long 2 YM-HM-02-029 Side board lock plastic-short 1 HM-20-394 Warning, crushing of hands label 1 HM-20-750 06 light wood future siderail color back left 1 Siderail kit, head end left with unit, wood YM-KIT-100054-W YM-02-141-MN2 SV2 Back left siderail assembly with unit 1 HM-22-1780 3M primer 94 handkerchief 1

www.stryker.com Quick reference replacement parts Kit name Number Kit contents Number Name Quantity HM-02-283 2 mm plastic washer (10 mm plastic washer) mould NO 34 4 HM-11-19 Q10 capped snap ring (DT/6668/44A) 2 HM-12-005 10x123,5 mm siderail pin 1 HM-12-145 12-145 10 x 305 mm siderail pin 1 YM-HM-02-418 Future siderail shock absorber PLS 2 HM-05-018 M8*90 half thread steel bolt 1 HM-20-557 Ø15 clips 5 HM-07-03 M8 iron washer 2 HM-08-06 M8 fibered nut 1 HM-11-31 Ø10 rue clip 2 YM-HM-02-028 Side board lock plastic-long 2 YM-HM-02-029 Side board lock plastic-short 1 HM-20-394 Warning, crushing of hands label 1 HM-20-755 07 wood color future siderail color back left 1 Siderail kit, head end right with unit YM-KIT-100055 YM-02-143-MN2 SV2 Back right siderail assembly with unit 1 HM-22-1780 3M primer 94 handkerchief 1 HM-02-283 2 mm plastic washer (10 mm plastic washer) mould NO 34 4 HM-11-19 Q10 capped snap ring (DT/6668/44A) 2 HM-12-005 10x123,5 mm siderail pin 1 HM-12-145 12-145 10 x 305 mm siderail pin 1 YM-HM-02-418 Future siderail shock absorber PLS 2

39 Quick reference replacement parts Kit name Number Kit contents Number Name Quantity HM-05-018 M8*90 half thread steel bolt 1 HM-20-557 Ø15 clips 5 HM-07-03 M8 iron washer 2 HM-08-06 M8 fibered nut 1 HM-11-31 Ø10 rue clip 2 YM-HM-02-028 Side board lock plastic-long 2 YM-HM-02-029 Side board lock plastic-short 1 HM-20-394 Warning, crushing of hands label 1 Siderail kit, head end right with unit, dark blue YM-KIT-100055-B YM-02-143-MN2 SV2 Back right siderail assembly with unit 1 HM-22-1780 3M primer 94 handkerchief 1 HM-02-283 2 mm plastic washer (10 mm plastic washer) mould NO 34 4 HM-11-19 Q10 capped snap ring (DT/6668/44A) 2 HM-12-005 10x123,5 mm siderail pin 1 HM-12-145 12-145 10 x 305 mm siderail pin 1 YM-HM-02-418 Future siderail shock absorber PLS 2 HM-05-018 M8*90 half thread steel bolt 1 HM-20-557 Ø15 clips 5 HM-07-03 M8 iron washer 2 HM-08-06 M8 fibered nut 1 HM-11-31 Ø10 rue clip 2 YM-HM-02-028 Side board lock plastic-long 2 YM-HM-02-029 Side board lock plastic-short 1 HM-20-394 Warning, crushing of hands label 1

www.stryker.com Quick reference replacement parts Kit name Number Kit contents Number Name Quantity HM-20-872 SV2 dark blue (Stryker) upper right siderail color sticker 1 Siderail kit, head end right with unit, dark wood YM-KIT-100055-D YM-02-143-MN2 SV2 Back right siderail assembly with unit 1 HM-22-1780 3M primer 94 handkerchief 1 HM-02-283 2 mm plastic washer (10 mm plastic washer) mould NO 34 4 HM-11-19 Q10 capped snap ring (DT/6668/44A) 2 HM-12-005 10x123,5 mm siderail pin 1 HM-12-145 12-145 10 x 305 mm siderail pin 1 YM-HM-02-418 Future siderail shock absorber PLS 2 HM-05-018 M8*90 half thread steel bolt 1 HM-20-557 Ø15 clips 5 HM-07-03 M8 iron washer 2 HM-08-06 M8 fibered nut 1 HM-11-31 Ø10 rue clip 2 YM-HM-02-028 Side board lock plastic-long 2 YM-HM-02-029 Side board lock plastic-short 1 HM-20-394 Warning, crushing of hands label 1 HM-20-759 08 dark wood future siderail color back right 1 Siderail kit, head end right with unit, light wood YM-KIT-100055-L YM-02-143-MN2 SV2 Back right siderail assembly with unit 1 HM-22-1780 3M primer 94 handkerchief 1 HM-02-283 2 mm plastic washer (10 mm plastic washer) mould NO 34 4

41 Quick reference replacement parts Kit name Number Kit contents Number Name Quantity HM-11-19 Q10 capped snap ring (DT/6668/44A) 2 HM-12-005 10x123,5 mm siderail pin 1 HM-12-145 12-145 10 x 305 mm siderail pin 1 YM-HM-02-418 Future siderail shock absorber PLS 2 HM-05-018 M8*90 half thread steel bolt 1 HM-20-557 Ø15 clips 5 HM-07-03 M8 iron washer 2 HM-08-06 M8 fibered nut 1 HM-11-31 Ø10 rue clip 2 YM-HM-02-028 Side board lock plastic-long 2 YM-HM-02-029 Side board lock plastic-short 1 HM-20-394 Warning, crushing of hands label 1 HM-20-749 06 light wood future siderail color back right 1 Siderail kit, head end right with unit, wood YM-KIT-100055-W YM-02-143-MN2 SV2 Back right siderail assembly with unit 1 HM-22-1780 3M primer 94 handkerchief 1 HM-02-283 2 mm plastic washer (10 mm plastic washer) mould NO 34 4 HM-11-19 Q10 capped snap ring (DT/6668/44A) 2 HM-12-005 10x123,5 mm siderail pin 1 HM-12-145 12-145 10 x 305 mm siderail pin 1 YM-HM-02-418 Future siderail shock absorber PLS 2 HM-05-018 M8*90 half thread steel bolt 1

www.stryker.com Quick reference replacement parts Kit name Number Kit contents Number Name Quantity HM-20-557 Ø15 clips 5 HM-07-03 M8 iron washer 2 HM-08-06 M8 fibered nut 1 HM-11-31 Ø10 rue clip 2 YM-HM-02-028 Side board lock plastic-long 2 YM-HM-02-029 Side board lock plastic-short 1 HM-20-394 Warning, crushing of hands label 1 HM-20-754 07 wood color future siderail color back right 1 Siderail kit, head end left W/O unit YM-KIT-100056 YM-02-141-MN4 SV2 Back left siderail assembly w/o unit 1 HM-22-1780 3M primer 94 handkerchief 1 HM-02-283 2 mm plastic washer (10 mm plastic washer) mould NO 34 4 HM-11-19 Q10 capped snap ring (DT/6668/44A) 2 HM-12-005 10x123,5 mm siderail pin 1 HM-12-145 12-145 10 x 305 mm siderail pin 1 YM-HM-02-418 Future siderail shock absorber PLS 2 HM-05-018 M8*90 half thread steel bolt 1 HM-07-03 M8 iron washer 2 HM-08-06 M8 fibered nut 1 HM-11-31 Ø10 rue clip 2 YM-HM-02-028 Side board lock plastic-long 2 YM-HM-02-029 Side board lock plastic-short 1 HM-20-394 Warning, crushing of hands label 1

43 Quick reference replacement parts Kit name Number Kit contents Number Name Quantity Siderail kit, head end left W/O unit, dark blue YM-KIT-100056-B YM-02-141-MN4 SV2 Back left siderail assembly w/o unit 1 HM-22-1780 3M primer 94 handkerchief 1 HM-02-283 2 mm plastic washer (10 mm plastic washer) mould NO 34 4 HM-11-19 Q10 capped snap ring (DT/6668/44A) 2 HM-12-005 10x123,5 mm siderail pin 1 HM-12-145 12-145 10 x 305 mm siderail pin 1 YM-HM-02-418 Future siderail shock absorber PLS 2 HM-05-018 M8*90 half thread steel bolt 1 HM-07-03 M8 iron washer 2 HM-08-06 M8 fibered nut 1 HM-11-31 Ø10 rue clip 2 YM-HM-02-028 Side board lock plastic-long 2 YM-HM-02-029 Side board lock plastic-short 1 HM-20-394 Warning, crushing of hands label 1 HM-20-873 SV2 dark blue (Stryker) upper left siderail color sticker 1 Siderail kit, head end left W/O unit, dark wood YM-KIT-100056-D YM-02-141-MN4 SV2 Back left siderail assembly w/o unit 1 HM-22-1780 3M primer 94 handkerchief 1 HM-02-283 2 mm plastic washer (10 mm plastic washer) mould NO 34 4 HM-11-19 Q10 capped snap ring (DT/6668/44A) 2 HM-12-005 10x123,5 mm siderail pin 1 HM-12-145 12-145 10 x 305 mm siderail pin 1

www.stryker.com Quick reference replacement parts Kit name Number Kit contents Number Name Quantity YM-HM-02-418 Future siderail shock absorber PLS 2 HM-05-018 M8*90 half thread steel bolt 1 HM-07-03 M8 iron washer 2 HM-08-06 M8 fibered nut 1 HM-11-31 Ø10 rue clip 2 YM-HM-02-028 Side board lock plastic-long 2 YM-HM-02-029 Side board lock plastic-short 1 HM-20-394 Warning, crushing of hands label 1 HM-20-760 08 dark wood future siderail color back left 1 Siderail kit, head end left W/O unit, light wood YM-KIT-100056-L YM-02-141-MN4 SV2 Back left siderail assembly w/o unit 1 HM-22-1780 3M primer 94 handkerchief 1 HM-02-283 2 mm plastic washer (10 mm plastic washer) mould NO 34 4 HM-11-19 Q10 capped snap ring (DT/6668/44A) 2 HM-12-005 10x123,5 mm siderail pin 1 HM-12-145 12-145 10 x 305 mm siderail pin 1 YM-HM-02-418 Future siderail shock absorber PLS 2 HM-05-018 M8*90 half thread steel bolt 1 HM-07-03 M8 iron washer 2 HM-08-06 M8 fibered nut 1 HM-11-31 Ø10 rue clip 2 YM-HM-02-028 Side board lock plastic-long 2 YM-HM-02-029 Side board lock plastic-short 1 HM-20-394 Warning, crushing of hands label 1

45 Quick reference replacement parts Kit name Number Kit contents Number Name Quantity HM-20-750 06 light wood future siderail color back left 1 Siderail kit, head end left W/O unit, wood YM-KIT-100056-W YM-02-141-MN4 SV2 Back left siderail assembly w/o unit 1 HM-22-1780 3M primer 94 handkerchief 1 HM-02-283 2 mm plastic washer (10 mm plastic washer) mould NO 34 4 HM-11-19 Q10 capped snap ring (DT/6668/44A) 2 HM-12-005 10x123,5 mm siderail pin 1 HM-12-145 12-145 10 x 305 mm siderail pin 1 YM-HM-02-418 Future siderail shock absorber PLS 2 HM-05-018 M8*90 half thread steel bolt 1 HM-07-03 M8 iron washer 2 HM-08-06 M8 fibered nut 1 HM-11-31 Ø10 rue clip 2 YM-HM-02-028 Side board lock plastic-long 2 YM-HM-02-029 Side board lock plastic-short 1 HM-20-394 Warning, crushing of hands label 1 HM-20-755 07 wood color future siderail color back left 1 Siderail kit, head end right W/O control panel YM-KIT-100057 YM-02-143-MN4 SV2 Back right siderail assembly w/o unit 1 HM-22-1780 3M primer 94 handkerchief 1 HM-02-283 2 mm plastic washer (10 mm plastic washer) mould NO 34 4 HM-11-19 Q10 capped snap ring (DT/6668/44A) 2

www.stryker.com Quick reference replacement parts Kit name Number Kit contents Number Name Quantity HM-12-005 10x123,5 mm siderail pin 1 HM-12-145 12-145 10 x 305 mm siderail pin 1 YM-HM-02-418 Future siderail shock absorber PLS 2 HM-05-018 M8*90 half thread steel bolt 1 HM-07-03 M8 iron washer 2 HM-08-06 M8 fibered nut 1 HM-11-31 Ø10 rue clip 2 YM-HM-02-028 Side board lock plastic-long 2 YM-HM-02-029 Side board lock plastic-short 1 HM-20-394 Warning, crushing of hands label 1 Siderail kit, head end right W/O control panel, dark blue YM-KIT-100057-B YM-02-143-MN4 SV2 Back right siderail assembly w/o unit 1 HM-22-1780 3M primer 94 handkerchief 1 HM-02-283 2 mm plastic washer (10 mm plastic washer) mould NO 34 4 HM-11-19 Q10 capped snap ring (DT/6668/44A) 2 HM-12-005 10x123,5 mm siderail pin 1 HM-12-145 12-145 10 x 305 mm siderail pin 1 YM-HM-02-418 Future siderail shock absorber PLS 2 HM-05-018 M8*90 half thread steel bolt 1 HM-07-03 M8 iron washer 2 HM-08-06 M8 fibered nut 1 HM-11-31 Ø10 rue clip 2 YM-HM-02-028 Side board lock plastic-long 2 YM-HM-02-029 Side board lock plastic-short 1

47 Quick reference replacement parts Kit name Number Kit contents Number Name Quantity HM-20-394 Warning, crushing of hands label 1 HM-20-872 SV2 dark blue (Stryker) upper right siderail color sticker 1 Siderail kit, head end right W/O control panel, dark wood YM-KIT-100057-D YM-02-143-MN4 SV2 Back right siderail assembly w/o unit 1 HM-22-1780 3M primer 94 handkerchief 1 HM-02-283 2 mm plastic washer (10 mm plastic washer) mould NO 34 4 HM-11-19 Q10 capped snap ring (DT/6668/44A) 2 HM-12-005 10x123,5 mm siderail pin 1 HM-12-145 12-145 10 x 305 mm siderail pin 1 YM-HM-02-418 Future siderail shock absorber PLS 2 HM-05-018 M8*90 half thread steel bolt 1 HM-07-03 M8 iron washer 2 HM-08-06 M8 fibered nut 1 HM-11-31 Ø10 rue clip 2 YM-HM-02-028 Side board lock plastic-long 2 YM-HM-02-029 Side board lock plastic-short 1 HM-20-394 Warning, crushing of hands label 1 HM-20-759 08 dark wood future siderail color back right 1 Siderail kit, head end right W/O control panel, light wood YM-KIT-100057-L YM-02-143-MN4 SV2 Back right siderail assembly w/o unit 1 HM-22-1780 3M primer 94 handkerchief 1 HM-02-283 2 mm plastic washer (10 mm plastic washer) mould NO 34 4

www.stryker.com Quick reference replacement parts Kit name Number Kit contents Number Name Quantity HM-11-19 Q10 capped snap ring (DT/6668/44A) 2 HM-12-005 10x123,5 mm siderail pin 1 HM-12-145 12-145 10 x 305 mm siderail pin 1 YM-HM-02-418 Future siderail shock absorber PLS 2 HM-05-018 M8*90 half thread steel bolt 1 HM-07-03 M8 iron washer 2 HM-08-06 M8 fibered nut 1 HM-11-31 Ø10 rue clip 2 YM-HM-02-028 Side board lock plastic-long 2 YM-HM-02-029 Side board lock plastic-short 1 HM-20-394 Warning, crushing of hands label 1 HM-20-749 06 light wood future siderail color back right 1 Siderail kit, head end right W/O control panel, wood YM-KIT-100057-W YM-02-143-MN4 SV2 Back right siderail assembly w/o unit 1 HM-22-1780 3M primer 94 handkerchief 1 HM-02-283 2 mm plastic washer (10 mm plastic washer) mould NO 34 4 HM-11-19 Q10 capped snap ring (DT/6668/44A) 2 HM-12-005 10x123,5 mm siderail pin 1 HM-12-145 12-145 10 x 305 mm siderail pin 1 YM-HM-02-418 Future siderail shock absorber PLS 2 HM-05-018 M8*90 half thread steel bolt 1 HM-07-03 M8 iron washer 2

49 Quick reference replacement parts Kit name Number Kit contents Number Name Quantity HM-08-06 M8 fibered nut 1 HM-11-31 Ø10 rue clip 2 YM-HM-02-028 Side board lock plastic-long 2 YM-HM-02-029 Side board lock plastic-short 1 HM-20-394 Warning, crushing of hands label 1 HM-20-754 07 wood color future siderail color back right 1 Siderail kit, SV2-50 head end left with unit YM-KIT-100058 YM-02-141-MN3 SV2-50 back left siderail assembly with unit 1 HM-22-1780 3M primer 94 handkerchief 1 HM-02-283 2 mm plastic washer (10 mm plastic washer) mould NO 34 4 HM-11-19 Q10 capped snap ring (DT/6668/44A) 2 HM-12-005 10x123,5 mm siderail pin 1 HM-12-145 12-145 10 x 305 mm siderail pin 1 YM-HM-02-418 Future siderail shock absorber PLS 2 HM-05-018 M8*90 half thread steel bolt 1 HM-07-03 M8 iron washer 2 HM-08-06 M8 fibered nut 1 HM-11-31 Ø10 rue clip 2 YM-HM-02-028 Side board lock plastic-long 2 YM-HM-02-029 Side board lock plastic-short 1 HM-20-557 Ø15 clips 5 HM-20-394 Warning, crushing of hands label 1 Siderail kit, SV2-50 head end left with unit, dark blue YM-KIT-100058-B YM-02-141-MN3 SV2-50 back left siderail assembly with unit 1

www.stryker.com Quick reference replacement parts Kit name Number Kit contents Number Name Quantity HM-22-1780 3M primer 94 handkerchief 1 HM-02-283 2 mm plastic washer (10 mm plastic washer) mould NO 34 4 HM-11-19 Q10 capped snap ring (DT/6668/44A) 2 HM-12-005 10x123,5 mm siderail pin 1 HM-12-145 12-145 10 x 305 mm siderail pin 1 YM-HM-02-418 Future siderail shock absorber PLS 2 HM-05-018 M8*90 half thread steel bolt 1 HM-07-03 M8 iron washer 2 HM-08-06 M8 fibered nut 1 HM-11-31 Ø10 rue clip 2 YM-HM-02-028 Side board lock plastic-long 2 YM-HM-02-029 Side board lock plastic-short 1 HM-20-557 Ø15 clips 5 HM-20-394 Warning, crushing of hands label 1 HM-20-873 SV2 dark blue (Stryker) upper left siderail color sticker 1 Siderail kit, SV2-50 head end left with unit, dark wood YM-KIT-100058-D YM-02-141-MN3 SV2-50 back left siderail assembly with unit 1 HM-22-1780 3M primer 94 handkerchief 1 HM-02-283 2 mm plastic washer (10 mm plastic washer) mould NO 34 4 HM-11-19 Q10 capped snap ring (DT/6668/44A) 2 HM-12-005 10x123,5 mm siderail pin 1 HM-12-145 12-145 10 x 305 mm siderail pin 1

51 Quick reference replacement parts Kit name Number Kit contents Number Name Quantity YM-HM-02-418 Future siderail shock absorber PLS 2 HM-05-018 M8*90 half thread steel bolt 1 HM-07-03 M8 iron washer 2 HM-08-06 M8 fibered nut 1 HM-11-31 Ø10 rue clip 2 YM-HM-02-028 Side board lock plastic-long 2 YM-HM-02-029 Side board lock plastic-short 1 HM-20-557 Ø15 clips 5 HM-20-394 Warning, crushing of hands label 1 HM-20-760 08 dark wood future siderail color back left 1 Siderail kit, SV2-50 head end left with unit, light wood YM-KIT-100058-L YM-02-141-MN3 SV2-50 back left siderail assembly with unit 1 HM-22-1780 3M primer 94 handkerchief 1 HM-02-283 2 mm plastic washer (10 mm plastic washer) mould NO 34 4 HM-11-19 Q10 capped snap ring (DT/6668/44A) 2 HM-12-005 10x123,5 mm siderail pin 1 HM-12-145 12-145 10 x 305 mm siderail pin 1 YM-HM-02-418 Future siderail shock absorber PLS 2 HM-05-018 M8*90 half thread steel bolt 1 HM-07-03 M8 iron washer 2 HM-08-06 M8 fibered nut 1 HM-11-31 Ø10 rue clip 2 YM-HM-02-028 Side board lock plastic-long 2 YM-HM-02-029 Side board lock plastic-short 1

www.stryker.com Quick reference replacement parts Kit name Number Kit contents Number Name Quantity HM-20-557 Ø15 clips 5 HM-20-394 Warning, crushing of hands label 1 HM-20-750 06 light wood future siderail color back left 1 Siderail kit, SV2-50 head end left with unit, wood YM-KIT-100058-W YM-02-141-MN3 SV2-50 back left siderail assembly with unit 1 HM-22-1780 3M primer 94 handkerchief 1 HM-02-283 2 mm plastic washer (10 mm plastic washer) mould NO 34 4 HM-11-19 Q10 capped snap ring (DT/6668/44A) 2 HM-12-005 10x123,5 mm siderail pin 1 HM-12-145 12-145 10 x 305 mm siderail pin 1 YM-HM-02-418 Future siderail shock absorber PLS 2 HM-05-018 M8*90 half thread steel bolt 1 HM-07-03 M8 iron washer 2 HM-08-06 M8 fibered nut 1 HM-11-31 Ø10 rue clip 2 YM-HM-02-028 Side board lock plastic-long 2 YM-HM-02-029 Side board lock plastic-short 1 HM-20-557 Ø15 clips 5 HM-20-394 Warning, crushing of hands label 1 HM-20-755 07 wood color future siderail color back left 1 Siderail kit, SV2-50 head end right with unit YM-KIT-100059 YM-02-143-MN3 SV2-50 back right siderail assembly with unit 1 HM-22-1780 3M primer 94 handkerchief 1

53 Quick reference replacement parts Kit name Number Kit contents Number Name Quantity HM-02-283 2 mm plastic washer (10 mm plastic washer) mould NO 34 4 HM-11-19 Q10 capped snap ring (DT/6668/44A) 2 HM-12-005 10x123,5 mm siderail pin 1 HM-12-145 12-145 10 x 305 mm siderail pin 1 YM-HM-02-418 Future siderail shock absorber PLS 2 HM-05-018 M8*90 half thread steel bolt 1 HM-07-03 M8 iron washer 2 HM-08-06 M8 fibered nut 1 HM-11-31 Ø10 rue clip 2 YM-HM-02-028 Side board lock plastic-long 2 YM-HM-02-029 Side board lock plastic-short 1 HM-20-557 Ø15 clips 5 HM-20-394 Warning, crushing of hands label 1 Siderail kit, SV2-50 head end right with unit, dark blue YM-KIT-100059-B YM-02-143-MN3 SV2-50 back right siderail assembly with unit 1 HM-22-1780 3M primer 94 handkerchief 1 HM-02-283 2 mm plastic washer (10 mm plastic washer) mould NO 34 4 HM-11-19 Q10 capped snap ring (DT/6668/44A) 2 HM-12-005 10x123,5 mm siderail pin 1 HM-12-145 12-145 10 x 305 mm siderail pin 1 YM-HM-02-418 Future siderail shock absorber PLS 2 HM-05-018 M8*90 half thread steel bolt 1

www.stryker.com Quick reference replacement parts Kit name Number Kit contents Number Name Quantity HM-07-03 M8 iron washer 2 HM-08-06 M8 fibered nut 1 HM-11-31 Ø10 rue clip 2 YM-HM-02-028 Side board lock plastic-long 2 YM-HM-02-029 Side board lock plastic-short 1 HM-20-557 Ø15 clips 5 HM-20-394 Warning, crushing of hands label 1 HM-20-872 SV2 dark blue (Stryker) upper right siderail color sticker 1 Siderail kit, SV2-50 head end right with unit, dark wood YM-KIT-100059-D YM-02-143-MN3 SV2-50 back right siderail assembly with unit 1 HM-22-1780 3M primer 94 handkerchief 1 HM-02-283 2 mm plastic washer (10 mm plastic washer) mould NO 34 4 HM-11-19 Q10 capped snap ring (DT/6668/44A) 2 HM-12-005 10x123,5 mm siderail pin 1 HM-12-145 12-145 10 x 305 mm siderail pin 1 YM-HM-02-418 Future siderail shock absorber PLS 2 HM-05-018 M8*90 half thread steel bolt 1 HM-07-03 M8 iron washer 2 HM-08-06 M8 fibered nut 1 HM-11-31 Ø10 rue clip 2 YM-HM-02-028 Side board lock plastic-long 2 YM-HM-02-029 Side board lock plastic-short 1 HM-20-557 Ø15 clips 5 HM-20-394 Warning, crushing of hands label 1

55 Quick reference replacement parts Kit name Number Kit contents Number Name Quantity HM-20-759 08 dark wood future siderail color back right 1 Siderail kit, SV2-50 head end right with unit, light wood YM-KIT-100059-L YM-02-143-MN3 SV2-50 back right siderail assembly with unit 1 HM-22-1780 3M primer 94 handkerchief 1 HM-02-283 2 mm plastic washer (10 mm plastic washer) mould NO 34 4 HM-11-19 Q10 capped snap ring (DT/6668/44A) 2 HM-12-005 10x123,5 mm siderail pin 1 HM-12-145 12-145 10 x 305 mm siderail pin 1 YM-HM-02-418 Future siderail shock absorber PLS 2 HM-05-018 M8*90 half thread steel bolt 1 HM-07-03 M8 iron washer 2 HM-08-06 M8 fibered nut 1 HM-11-31 Ø10 rue clip 2 YM-HM-02-028 Side board lock plastic-long 2 YM-HM-02-029 Side board lock plastic-short 1 HM-20-557 Ø15 clips 5 HM-20-394 Warning, crushing of hands label 1 HM-20-749 06 light wood future siderail color back right 1 Siderail kit, SV2-50 head end right with unit, wood YM-KIT-100059-W YM-02-143-MN3 SV2-50 back right siderail assembly with unit 1 HM-22-1780 3M primer 94 handkerchief 1 HM-02-283 2 mm plastic washer (10 mm plastic washer) mould NO 34 4

www.stryker.com Quick reference replacement parts Kit name Number Kit contents Number Name Quantity HM-11-19 Q10 capped snap ring (DT/6668/44A) 2 HM-12-005 10x123,5 mm siderail pin 1 HM-12-145 12-145 10 x 305 mm siderail pin 1 YM-HM-02-418 Future siderail shock absorber PLS 2 HM-05-018 M8*90 half thread steel bolt 1 HM-07-03 M8 iron washer 2 HM-08-06 M8 fibered nut 1 HM-11-31 Ø10 rue clip 2 YM-HM-02-028 Side board lock plastic-long 2 YM-HM-02-029 Side board lock plastic-short 1 HM-20-557 Ø15 clips 5 HM-20-394 Warning, crushing of hands label 1 HM-20-754 07 wood color future siderail color back right 1 Under bed light replacement kit YM-KIT-100086 HM-17-297 Under bed light UBL2 1 HM-06-112 2,9*16 sheet metal screw 2

57 Service Fowler (backrest) actuator replacement Tools required: • Small flat screwdriver • Needle nose pliers Procedure: 1. Apply the brakes. 2. Raise the product to the highest height position. 3. Power down the bed and unplug the power cord from the wall outlet. 4. Using the CPR release, lower the Fowler (backrest) to a flat (0 degrees) position. 5. Using a small flat screwdriver, push in both locking tabs to remove the cable retainer on the Fowler (backrest) actuator electrical quick connector. 6. Unplug the connector. 7. Using one hand to support the Fowler (backrest) actuator and a small flat screwdriver, open the CPR cable cover on the Fowler (backrest) actuator. 8. Pulling back on the CPR cables, remove the CPR cable mechanism from the Fowler (backrest) actuator. 9. Using needle nose pliers, remove and discard the rue ring cotter pins (A) (Figure 2 on page 57) from each clevis pin. Figure 2: Fowler (backrest) actuator 10. Using one hand, support the Fowler (backrest) actuator and remove and save the head end clevis pin (B) (Figure 2 on page 57) then allow the Fowler (backrest) actuator to pivot down. 11. Using one hand, support the Fowler (backrest) actuator and remove and save the foot end clevis pin (C) (Figure 2 on page 57) and spacer. 12. Remove and discard the Fowler (backrest) actuator. 13. Reverse steps to reinstall. Note: Make sure that the cable ties stay in the same position during reinstallation. 14. Verify proper operation of the product before returning it to service. Gatch (legrest) actuator replacement Tools required: • Small flat screwdriver

www.stryker.com Service Gatch (legrest) actuator replacement (Continued) • Needle nose pliers Procedure: 1. Apply the brakes. 2. Raise the product to the highest height position. 3. Power down the bed and unplug the power cord from the wall outlet. 4. Using a small flat screwdriver, push in both locking tabs to remove the cable retainer on the gatch (legrest) actuator electrical quick connector. 5. Unplug the gatch (legrest) actuator cable to allow the removal of the gatch (legrest) actuator. 6. Using needle nose pliers, remove and discard the rue ring cotter pins (A) (Figure 3 on page 58) from each clevis pin. Figure 3: Gatch (legrest) actuator 7. Using one hand, support the gatch (legrest) actuator and remove the foot end clevis pin (C) (Figure 3 on page 58) and spacers then allow the gatch (legrest) actuator to pivot down. 8. Using one hand, support the gatch (legrest) actuator and remove the head end clevis pin (D) (Figure 3 on page 58) and spacer. 9. Remove and discard the gatch (legrest) actuator. 10. Reverse steps to reinstall. 11. Verify proper operation of the product before returning it to service. Head end lift actuator replacement Tools required: • Small flat screwdriver • Needle nose pliers Procedure: 1. Apply the brakes. 2. Support the head end litter cross brace (A) to support the head end litter (Figure 4 on page 59).

59 Service Head end lift actuator replacement (Continued) 3. Power down the bed and unplug the power cord from the wall outlet. 4. Using a small flat screwdriver, gently push in both locking tabs to remove the cable retainer on the head end lift actuator electrical connector. 5. Unplug the connector. 6. Using needle nose pliers, remove and discard the rue ring cotter pins (B) from each clevis pin (Figure 4 on page 59). 7. Using one hand, support the head end lift actuator and remove and discard the head end clevis pin (C) then allow the head end lift actuator to pivot down (Figure 4 on page 59). 8. Using one hand, support the head end lift actuator and remove and discard the foot end clevis pin (D) and spacer (Figure 4 on page 59). 9. Remove and discard the head end lift actuator. 10. Reverse steps to reinstall. 11. Verify proper operation of the product before returning it to service. Figure 4: Head end lift actuator Foot end lift actuator replacement Tools required: • Small flat screwdriver • Needle nose pliers

www.stryker.com Service Foot end lift actuator replacement (Continued) Procedure: 1. Apply the brakes. 2. Support the foot end litter cross brace (A) to support the foot end litter (Figure 5 on page 60). 3. Power down the bed and unplug the power cord from the wall outlet. 4. Using a small flat screwdriver, gently push in both locking tabs to remove the cable retainer on the foot end lift actuator electrical connector. 5. Unplug the connector. 6. Using needle nose pliers, remove and discard the rue ring cotter pins (B) from each clevis pin (Figure 5 on page 60). 7. Using one hand, support the foot end lift actuator and remove and discard the foot end clevis pin (C) then allow the foot end lift actuator to pivot down (Figure 5 on page 60). 8. Using one hand, support the foot end lift actuator and remove and discard the head end clevis pin (D) and spacer (Figure 5 on page 60). 9. Remove and discard the foot end lift actuator. 10. Reverse steps to reinstall. 11. Verify proper operation of the product before returning it to service. Figure 5: Foot end lift actuator

61 Service Non-steer caster replacement Tools required: • Large flat screwdriver • Floor jack (small) • Torque wrench with 5 mm hex bit (9.5 Nm) • 5 mm hex wrench • Needle nose pliers • Hammer Procedure: 1. Put the brake in the neutral position. CAUTION With the brake in the neutral position, the product could move. 2. Raise the product to the highest height position. 3. Unplug the power cord from the wall outlet. 4. Using needle nose pliers, remove and discard the rue ring cotter pin (G) from the hex shaft (Figure 6 on page 62). 5. Pull the brake pedal off the hex shaft and set aside (Figure 6 on page 62). 6. Remove and save the plastic washer (H) that is on the hex shaft (Figure 6 on page 62). 7. Using a hammer and a large screw driver, remove and discard the starlock retainer (K) that is on the hex shaft (Figure 6 on page 62). 8. Using a 5 mm hex wrench, remove and discard the two screws (I) and washers (J) that secure the non-steer caster to the base frame (Figure 6 on page 62). 9. Use a small floor jack to lift the base frame cross tube to loosen the non-steer caster. 10. Grasp the opposite brake/steer pedal and pull outward about four inches (100 mm) to remove and discard the non- steer caster. Note: Note the position of the label on the mounting shaft of the old caster for reinstallation of the replacement caster. 11. Reverse steps to reinstall. WARNING Always make sure to line the hex shaft with the hex in the caster. Test the caster to identify the direction of the brake. Damage may occur if you install the caster incorrectly. Note: Torque the caster mounting screws (I) to 9.5 Nm +/- 1.5 Nm. 12. Verify proper operation of the product before returning it to service.

www.stryker.com Service Non-steer caster replacement (Continued) Figure 6: Non-steer caster Steer (head left) caster replacement Tools required: • Large flat screwdriver • Floor jack (small) • Torque wrench with 5 mm hex bit (9.5 Nm) • 5 mm hex wrench • Needle nose pliers • Hammer Procedure: 1. Put the brake in the neutral position. CAUTION With the brake in the neutral position, the product could move. 2. Raise the product to the highest height position. 3. Unplug the power cord from the wall outlet. 4. Using needle nose pliers, remove and discard the rue ring cotter pin (G) from the hex shaft (Figure 7 on page 63).

63 Service Steer (head left) caster replacement (Continued) 5. Pull the brake pedal off the hex shaft and set aside. 6. Remove and save the plastic washer (H) that is on the hex shaft (Figure 7 on page 63). 7. Using a hammer and a large screw driver, remove and discard the starlock retainer (K) that is on the hex shaft (Figure 7 on page 63). 8. Using a 5 mm hex wrench, remove and discard the two screws (I) and washers (J) that secure the non-steer caster to the base frame (Figure 7 on page 63). 9. Use a small floor jack to lift the base frame cross tube to loosen the non-steer caster. 10. Grasp the opposite brake/steer pedal and pull outward about four inches (100 mm) to remove and discard the non- steer caster. Note: Note the position of the label on the mounting shaft of the old caster for reinstallation of the replacement caster. 11. Reverse steps to reinstall. WARNING Always make sure to line the hex shaft with the hex in the caster. Test the caster to identify the direction of the brake. Damage may occur if you install the caster incorrectly. Note: Torque the caster mounting screws (I) to 9.5 Nm +/- 1.5 Nm. 12. Verify proper operation of the product before returning it to service. Figure 7: Steer caster

www.stryker.com Service Fifth wheel replacement Tools required: • 3/8 in. drive ratchet • 13 mm socket Procedure: 1. Put the brake in the neutral position. CAUTION With the brake in the neutral position, the product could move. 2. Raise the product to the highest height position. 3. Unplug the power cord from the wall outlet. 4. Using a 3/8 in. drive ratchet and 13 mm socket, remove and save the nut and washers from the top of the fifth wheel assembly. 5. Remove and discard the fifth wheel assembly. 6. Reverse steps to reinstall. Note: You may have to compress the fifth wheel assembly slightly to reinstall. 7. Verify proper operation of the product before returning it to service. Head end siderail gas cylinder replacement Tools required: • Large flat screwdriver • Hammer • 3/8 in. drive ratchet • 13 mm socket • 13 mm combination wrench Procedure: 1. Apply the brakes. 2. Raise the product to the highest height position. 3. Power down the bed and unplug the power cord from the wall outlet. 4. Raise the siderail to the full upright and latched position. 5. Using a 3/8 in. drive ratchet and 13 mm socket with a 13 mm combination wrench, remove and discard the bolt, spacers, and nut that secures the head end siderail gas cylinder to the fowler (backrest) frame. 6. Using a large flat screwdriver and a hammer, remove one of the push nuts (A) that secures the bottom of the head end siderail gas cylinder (C) to the siderail mechanism (Figure 8 on page 65). 7. Remove the pivot pin (B) (Figure 8 on page 65). 8. Remove and discard the head end siderail gas cylinder (C). 9. Reverse steps to reinstall. 10. Verify proper operation of the product before returning it to service.

65 Service Head end siderail gas cylinder replacement (Continued) Figure 8: Head end siderail gas cylinder Foot end siderail gas cylinder replacement Tools required: • Large flat screwdriver • Small flat screwdriver • Hammer Procedure: 1. Apply the brakes. 2. Raise the product to the highest height position. 3. Power down the bed and unplug the power cord from the wall outlet. 4. Raise the siderail to the full upright and latched position. 5. Using a small screwdriver, remove and discard the e-clip that secures the foot end siderail gas cylinder to the foot section frame. 6. Remove and save the pin that secures the foot end siderail gas cylinder to the foot section frame. 7. Using a large flat screwdriver and a hammer, remove one of the push nuts (A) that secures the bottom of the foot end siderail gas cylinder to the siderail mechanism (Figure 9 on page 66). 8. Remove and discard the pivot pin (B) and foot end siderail gas cylinder (C) (Figure 9 on page 66). 9. Reverse steps to reinstall. 10. Verify proper operation of the product before returning it to service.

www.stryker.com Service Foot end siderail gas cylinder replacement (Continued) Figure 9: Foot end siderail gas cylinder Lower leg section locking mechanism replacement Tools required: • 3/8 in. drive ratchet • 13 mm socket • 13 mm combination wrench Procedure: 1. Apply the brakes. 2. Raise the product to the highest height position. 3. Power down the bed and unplug the power cord from the wall outlet. 4. Raise the lower leg section (A) (Figure 10 on page 67). 5. Lock the lower leg section. Note: If you cannot lock the lower leg section, find another way to support the lower leg section. 6. Using a 13 mm combination wrench and a 13 mm socket, remove and save the upper bolt and nut that secure the lower leg section locking mechanism (B) to the foot section weldment (Figure 10 on page 67). 7. Using a 13 mm socket, remove and save the bolt (C), washers (D, E), and nut (F) that secures the bottom of the lower leg section locking mechanism to the litter frame (Figure 10 on page 67). 8. Remove and discard the lower leg section locking mechanism (B) (Figure 10 on page 67). 9. Reverse steps to reinstall. 10. Verify proper operation of the product before returning it to service.

67 Service Lower leg section locking mechanism replacement (Continued) Figure 10: Lower leg section locking mechanism Patient control pendant replacement Tools required: • Diagonal pliers Procedure: 1. Apply the brakes. 2. Raise the product to the highest height position. 3. Power down the bed and unplug the power cord from the wall outlet. 4. Remove the three cable routing covers that secure the gatch (legrest) actuator cable to the litter frame. 5. Cut the cable tie that secures the pendant to the bottom of the litter frame. 6. Unplug the patient control pendant cable from the junction box. 7. Dispose of the patient control pendant. 8. Reverse steps to reinstall. 9. Verify proper operation of the product before returning it to service. Nurse control pendant replacement Tools required: • Diagonal pliers

www.stryker.com Service Nurse control pendant replacement (Continued) Procedure: 1. Apply the brakes. 2. Raise the product to the highest height position. 3. Power down the bed and unplug the power cord from the wall outlet. 4. Using diagonal pliers, cut and discard the cable tie that secures the fowler (backrest) actuator cable to the wire routing channel. 5. Remove the three cable routing covers that secure the gatch (legrest) actuator cable to the litter frame. 6. Unplug the nurse control pendant cable from the junction box. 7. Dispose of the nurse control pendant. 8. Reverse steps to reinstall. 9. Verify proper operation of the product before returning it to service. Siderail control panel (inside and outside siderail) replacement Tools required: • Flat screwdriver Procedure: 1. Apply the brakes. 2. Raise the product to the highest height position. 3. Unplug the power cord from the wall outlet. 4. Using a flat screwdriver, carefully push in and up in the slotted access hole to remove the control panel from the siderail hoop. 5. Unplug the cable connecting the siderail control panel to the junction box. 6. Remove and discard the siderail control panel. 7. Reverse steps to reinstall. 8. Verify proper operation of the product before returning it to service. Control box replacement Tools required: • Diagonal pliers • Small flat screwdriver • 3/8 in. drive ratchet • 10 mm socket • 10 mm combination wrench Procedure: 1. Apply the brakes. 2. Raise the product to the highest height position. 3. Power down the bed and unplug the power cord from the wall outlet. 4. Turn the battery off using the nurse control. 5. Raise and lock the lower leg section in the highest position. 6. Using a small flat screwdriver, un-clip the actuator cable retainer (A) from the control box (Figure 11 on page 69). 7. Remove and save the actuator cable retainer. 8. Using a small flat screwdriver, push in on the power cord lock and gently pull outward on the power cord.

69 Service Control box replacement (Continued) 9. Remove the power cord from the control box. 10. Unplug the control cables and the battery cable from the control box. Note: Pay attention to the control cable connection locations for reinstallation. 11. Using a 10 mm combination wrench and a 10 mm socket, remove the bolt (B) that secures the control box to the litter frame (Figure 11 on page 69). 12. Remove and discard the control box. 13. Reverse steps to reinstall. 14. Verify proper operation of the product before returning it to service. Figure 11: Control box Battery replacement Tools required: • Diagonal pliers • #2 Phillips screwdriver Procedure: 1. Apply the brakes. 2. Raise the product to the highest height position. 3. Power down the bed and unplug the power cord from the wall outlet. 4. Remove the cable routing cover that secures the gatch (legrest) actuator cable to the litter frame. 5. Using diagonal pliers, cut and discard the cable tie that secures the battery cable to all of the actuator cables. 6. Using a #2 Phillips screwdriver, unscrew the four screws (A) that secure the battery to the litter frame (Figure 12 on page 70). Note: Support the battery while removing the screws so the battery does not fall. 7. Remove the battery.

www.stryker.com Service Battery replacement (Continued) 8. Dispose of the battery according to local laws and procedures. 9. Reverse steps to reinstall. 10. Verify proper operation of the product before returning it to service. Figure 12: Battery Power cord replacement Tools required: • #2 Phillips screwdriver Procedure: 1. Apply the brakes. 2. Raise the product to the highest height position. 3. Power down the bed and unplug the power cord from the wall outlet. 4. Remove the two screws (A) that secure the power cord connection cover (B) to the litter frame (Figure 13 on page 71). 5. Remove and discard the external power cord (C) from the internal power cord (Figure 13 on page 71). 6. Reverse steps to reinstall. 7. Verify proper operation of the product before returning it to service.

71 Service Power cord replacement (Continued) Figure 13: Power cord Head end siderail hoop replacement Tools required: • #2 Phillips screwdriver • Flat screwdriver Procedure: 1. Apply the brakes. 2. Raise the product to the highest height position. 3. Power down the bed and unplug the power cord from the wall outlet. 4. Raise the siderail to the full upright and latched position. 5. Remove the mattress. 6. Remove the part number label from the head side of the control box assembly. 7. Using a flat screwdriver, carefully pry the outer panel away from the siderail hoop until the hoop fully unsnaps from the inner panel. 8. Unplug the cable connecting the siderail control panel to the control box. 9. Remove the siderail control panel. 10. Using a #2 Phillips screwdriver, remove and save the cover screw on the bottom of the siderail hoop on either side of the siderail pivot. 11. Using a flat screwdriver, carefully pry outward on the siderail pivot cover. 12. Using a #2 Phillips screwdriver, remove and discard the six screws (A) that secure the siderail hoop (B) to the siderail mechanism (Figure 14 on page 72). Note: Support the siderail hoop while removing the screws so the siderail hoop does not fall. 13. Remove and discard the siderail hoop. 14. Reverse steps to reinstall. 15. Verify proper operation of the product before returning it to service.

www.stryker.com Service Head end siderail hoop replacement (Continued) Figure 14: Head end siderail hoop Foot end siderail hoop replacement Tools required: • #2 Phillips screwdriver • Flat screwdriver Procedure: 1. Apply the brakes. 2. Raise the product to the highest height position. 3. Power down the bed and unplug the power cord from the wall outlet. 4. Raise the siderail to the full upright and latched position. 5. Remove the mattress. 6. Using a #2 Phillips screwdriver, remove and save the cover screw on the bottom of the siderail hoop on either side of the siderail pivot. 7. Using a flat screwdriver, carefully pry outward on the siderail pivot cover. 8. Using a #2 Phillips screwdriver, remove and discard the six screws (A) that secure the siderail hoop (B) to the siderail mechanism (Figure 14 on page 72). Note: Support the siderail hoop while removing the screws so the siderail hoop does not fall. 9. Remove and discard the siderail hoop. 10. Reverse steps to reinstall. 11. Verify proper operation of the product before returning it to service.

73 Brake system Item Number Name Quantity A YM-FUTUREBALT-003-BY 5. wheel compatible lower chassis white 3 B YM-03-04-10-0760-HZR- GL Ø11 hexagon rod 760 mm with hole 2 C YM-FUTUREBAKT-003-BY Future LB 5. wheel compatible transfer white 2 D HM-01-83 150 mm no steer lock antistatic single integral wheel 1

www.stryker.com Brake system Item Number Name Quantity E HM-01-54 2046UAP150R36-32S30 150 mm no steer lock not antistatic single caster 3 F HM-09-04 DIN 6798 A/J - M6 serrated lock washer 1 G HM-05-106 M6*16 imbus bolt 8 H YM-HM-02-299 Hexagonal shaft bearing part 4 I YM-HM-02-71 12 thick PLS washer DMR071 4 J HM-09-18 Ø10 rivet nut 2 K HM-16-113 260 mm grounding cable 1 L HM-06-02 3,9 x 13 cross recessed pan head tapping screw 1 M HM-09-23 M6 rivet nut 4 N YM-5TKR-001 5.wheel assembly group 1 O HM-05-041 M6*30 hexagon socket button head screw 4 P HM-07-22 M6 iron washer (small) 8 Q HM-11-34 Ø13 rue segman 4 R HM-20-424 Pedal label - left 2 S HM-20-423 Pedal label - right 2 T HM-12-004 Ø8 perforated pin 1 U YM-HM-02-026 8,5 x 16 x 2,2 mm plastic washer 2 V HM-11-35 Ø8 rue clip 1 W YM-HM-02-023 Pedal plastic body 4 X YM-SV2PDL-001-BY Pedal sheet weld assembly 4 Y HM-07-09 Special pedal washer 8 Z HM-06-86 Ø6 x 16 cross recessed raised cheese head screws 8 AA HM-06-001 M6 x 25 mushroom head square neck bolt 4 AB HM-12-905 Transfer laser bush (bronze) 4 AC HM-08-05 M6 fibered nut 4 AD YM-04-142-BY 5. wheel - base frame connection sheet 2 AE YM-HM-02-025 Transfer bar Ø8 plastic hole cap 1

75 Brake system Item Number Name Quantity AF HM-09-30 M6 toothed washer (DIN 6797 A) 8 AG HM-11-10 11 mm Snap ring (lipper) KMS starlock push on BV/6706 fastener 4

www.stryker.com Base and leg assembly Item Number Name Quantity A HM-12-FTR011 Ø14xØ10x41 mm pin 2 B HM-11-31 Ø10 rue clip 2 C YM-HM-02-402 Ø34 pipe bush main mechanism 2 D YM-FUTURELBANA-004- MN Main mechanism without hole 1 E HM-12-FTR007 Ø14 bush main mechanism 4 F HM-05-153 M10x35 mm socket button head screw 4 G YM-HM-02-398 Ø18 bush main mechanism 4 H HM-09-18 Ø10 rivet nut 4 I YM-HM-02-396 Main mechanism sled delrin 4 J HM-05-54 M10x16 hex socket head cap screw 4

77 Base and leg assembly Item Number Name Quantity K HM-08-07 M10 prevailing torque type hexagon nut 4 L YM-FUTURELBANA-002- MN Main mechanism with hole 1 M YM-HM-02-399 Ø14 plastic washer 4 N YM-04-FTR011-HZR-BY Main mechanism Z laser cut sheet 2

www.stryker.com Base and leg assembly with 5th wheel (option) Item Number Name Quantity A YM-5TKR-001 Fifth wheel assembly group 1 B HM-09-23 M6 rivet nut 4 C HM-05-041 M6*30 hexagon socket button head screw 4 D YM-04-142-BY Fifth wheel-base frame connection sheet 2 E HM-11-35 Ø8 rue clip 1 F HM-12-004 Ø8 perforated pin 1 G YM-HM-02-026 8,5 x 16 x 2,2 mm plastic washer 2 H HM-07-22 M6 steel washer (small) 4

79 Litter / frame assembly Item Number Name Quantity A YM-026-010-MN Demounted headboard assembly 1 B HM-05-006 M10x70 hexagon head bolt 4 C HM-07-04 M10 steel washer 8 D HM-08-07 M10 prevailing torque type hexagon nut 4 E HM-06-09 3,9x25 mm cross recessed countersunk head tapping screw 2 F YM-HM-02-408 Backrest support plastic 2 G YM-FUTURELBUST-002- 00-BY SV2 prolonged top chassis white 1 H YM-HM-02-34 30x50x2 mm profile spile 4 I HM-20-840 Extension lock 2 J YM-16-49-03 25x25x360 mm cable holder 1 K HM-12-FTR011 Ø14xØ10x41 mm pin 2 L HM-11-31 Ø10 rue clip 2 M YM-16-49-04 25x25x200 mm cable holder 1 N YM-HM-02-401 Main mechanism plastic half bush 2

www.stryker.com Litter / frame assembly Item Number Name Quantity O YM-16-49-06 25x25x100 mm cable holder 1 P YM-16-49-04 25x25x200 mm cable holder 1 Q YM-16-49-01 25x25x550 mm cable holder 1 R YM-16-49-02 25x25x730 mm cable holder 1 S YM-HM-02-56 Buffer 2 T HM-06-49 Cross recessed countersunk head tapping screw 2 U YM-039-004-00-MN Bed extension assembly 2

81 Bumper roller assembly Item Number Name Quantity A YM-HM-02-413 Accessory socket sleeve 2 B HM-12-128 Grounding chrome 1 C HM-09-04 6 mm serrated washer (ring) DIN 6798 1 D YM-04-100-HZR3 Cable stow 20b-3 1 E HM-06-02 Star drive round head bolt (3.9 x 13 mm) 2 F HM-02-354 Future bumper 2 G HM-12-FTR001 12-FT001 future bumper pin 2 H HM-02-391 5 mm C shaped snap ring DIN 6799 2 I HM-02-55 Head board lock pin plastic encasing 2 J YM-04-322-HZR-1 Detachable bumper to chassis connection arm (right side) 1 K YM-04-322-HZR Detachable bumper chassis to main chassis connection arm (left side) 1 L YM-03-01-01-01250-HZR 45 x 2 x 150 mm bumper chassis side tubes 2 M YM-03-02-41-877-HZR1 Main bumper profile 40 x 60 x 877 mm 1

www.stryker.com Bed extender assembly Item Number Name Quantity A YM-27-01-106 HPL footrest extension 1 B YM-039-004-00-BY Bed extender weldment 1 C YM-20-011 Plastic linen tray 1 D YM-UZTMSLTTC-001 Bolster mattress retainers 2 E HM-06-82 M14 x 12 mm Phillips screw 6 F YM-UZTMCIRT-MN Bolster mattress Velcro® 1 G HM-06-63 M14 x 16 mm Phillips screw 6 H YM-HM-02-413 Accessory socket sleeve 2 I HM-02-354 Future bumper 2 J HM-12-FTR001 12-FT001 future bumper pin 2

83 Bed extender assembly Item Number Name Quantity K HM-11-05 6 mm C shape snap ring DIN 6799 2 L YM-02-55 Footboard pin socket 2 M HM-08-38 M4 hex nut 2 N YM-HM-02-416 Litter frame plastic end caps 2 O YM-HM-02-415 Bed extender block stops 2 P YM-04-FTR023-HZR-BY HPL extension mounting bracket 2 Q YM-04-FTR022-HZR-BY HPL extension mounting bracket 1 R HM-06-02 Ø3.9 x 13 mm Phillips screw 6 S HM-08-19 M4 x .7 nylock nut 4 T HM-03-04-03-0650-HZR- BY Ø8 mm linen tray bar 1

www.stryker.com Hi-Lo actuators Item Number Name Quantity A HM-12-FTR011 Ø14xØ10x41 mm pin 2 B HM-17-304 8000 N LA40 150 mm stroke actuator 2 C HM-11-31 Ø10 rue clip 4 D HM-12-FTR010 Ø14xØ10x65 mm actuator connection pin 2 E YM-HM-02-027 Actuator pin fixing bush 2

85 Control box and battery Item Number Name Quantity A HM-17-16 BA1812-1300-000 Linak CB6 battery 1 B HM-05-043 M5*20 imbus bolt 4 C HM-07-22 M6 iron washer (small) 6 D HM-08-04 M5 fibered nut 4 E YM-03-03-01-0425-HZR 5 x 20 mm battery mounting bracket 2 F HM-06-049 3.9 x 16 mm pan head self drilling screw 4 G HM-17-314 Control box 1 H HM-05-010 M6*50 steel bolt 1 I HM-08-05 M6 fibered nut 1 J HM-17-174 Control box mounting bracket 1 K HM-06-02 3.9 x 13 mm pan head self drilling screw 2 L HM-07-01 M6 metal standard washer (large) 1/4 washer 2

www.stryker.com Litter fowler (backrest) assembly Item Number Name Quantity A YM-27-01-005 Plastic backrest cover 1 B YM-008-013-00-BY Backrest weldment 1 C YM-FUTURESRT-001-BY Siderail mounting bracket 2 D YM-04-102-BY 102-6 laser cut link 2 E YM-04-103-BY 103-6 laser cut link 2 F HM-02-13 Red plastic CPR release handle 2 G HM-05-032 M8 x 20 mm countersunk bolt 6 H HM-06-30 M5 x 15 mm self drilling star bolt 4 I YM-15-05-0450-HZR1 X-Ray cassette track 2 J HM-08-06 M8 fibered nut 2 K HM-07-03 M8 iron washer 4 L HM-05-018 M8*90 half thread steel bolt 2

87 Litter fowler (backrest) assembly Item Number Name Quantity M HM-08-35 M8 rivet nut 6 N HM-11-03 10 mm snap ring DIN 471 2 O HM-02-283 2 mm plastic washer (10 mm plastic washer) mould NO 34 14 P HM-12-103 Ø10 x 44.5 mm pin 2 Q HM-06-72 Ø5.5 x 19mm torque screw 6 R HM-05-005 Ø10 x 35 mm hex head bolt 4 S YM-HM-02-88 Ø10 mm plastic bushing 8 T HM-07-04 M10 iron washer 8 U HM-08-07 M10 fiber hex nut 8 V HM-06-89 M10 x 55 mm carriage bolt 4 W YM-FUTURELBUST-001- BY Litter frame weldment 1

www.stryker.com Litter seat assembly Item Number Name Quantity A HM-02-120 Plastic seat cover 1 B YM-FUTURELBUST-001- BY Litter frame weldment 1

89 Litter gatch (legrest) assembly Item Number Name Quantity A HM-02-121 Plastic calf rest cover 1 B HM-02-119 Plastic thigh rest cover 1 C YM-007-006-BY Calf rest weldment 1 D YM-006-003-BY Thigh rest weldment 1 E HM-20-517 Foot prop assembly 2 F YM-04-102-BY 102-6 laser cut link 2 G YM-04-103-BY 103-6 laser cut link 2 H YM-HM-02-179 Bolt cap 4 I HM-08-07 M10 fiber hex nut 10 J HM-07-04 M10 iron washer 12 K HM-02-283 2 mm plastic washer (10 mm plastic washer) mould NO 34 12 L HM-06-89 M10 x 55 mm carriage bolt 4 M YM-HM-02-88 Ø10 mm plastic bushing 8 N HM-05-005 M10 x 35 mm hex head bolt 4

www.stryker.com Litter gatch (legrest) assembly Item Number Name Quantity O HM-06-88 M8 x 47 mm carriage bolt 2 P HM-07-03 M8 iron washer 2 Q HM-08-06 M8 fibered nut 2 R HM-06-66 M6 x 15 mm button head screw 1 S YM-HM-02-55 Ø9 x 12.4 mm plastic screw 2 T YM-FUTURELBUST-001- BY Litter frame weldment 1

91 Fowler (backrest) actuator Item Number Name Quantity A HM-11-31 Ø10 rue clip 2 B HM-12-FTR010 Ø14xØ10x65 mm actuator connection pin 2 C HM-17-303 4000 N LA40 QR 215 mm actuator 1 D YM-HM-02-027 Actuator pin fixing bush 1

www.stryker.com Gatch (legrest) actuator Item Number Name Quantity A HM-11-31 Ø10 rue clip 2 B YM-HM-02-287 Ø10.6xØ18x14.1 mm plastic bush 2 C YM-HM-02-70 Ø10.6xØ18x5 mm plastic washer 2 D HM-12-FTR009 Actuator calf pin 10x96.5 mm 2 E HM-17-305 6000 N LA40 100 mm stroke actuator 1 F HM-12-FTR010 Ø14xØ10x65 mm actuator connection pin 1 G YM-HM-02-027 Actuator pin fixing bush 1

93 Siderail head end assembly Item Number Name Quantity A YM-02-144-MN1 SV2 right foot siderail assembly 1 B HM-12-145 Ø10x305 mm siderail pin 1 C HM-02-283 Ø10x2 mm plastic washer 6 D HM-11-19 Ø10 hook ring 2 E HM-12-005 10x123.5 mm siderail pin 1 F YM-HM-02-028 Side board lock plastic- long 2 G YM-HM-02-029 Side board lock plastic- short 1 H HM-11-31 Ø10 rue clip 2 Siderail laminate Number (left) Number (right) Dark blue HM-20-853 HM-20-852 Dark wood HM-20-760 HM-20-759 Light wood HM-20-750 HM-20-749 Wood HM-20-755 HM-20-754

www.stryker.com Siderail foot end assembly Item Number Name Quantity A YM-02-142-MN1 SV2 left siderail for foot 1 B HM-11-19 Ø10 hook ring 2 C HM-02-283 Ø10x2 mm plastic washer 6 D YM-HM-02-029 Side board lock plastic- short 1 E HM-12-005 10x123,5 mm siderail pin 1 F YM-HM-02-028 Side board lock plastic- long 2 G HM-12-145 Ø10x305 mm siderail pin 1 H HM-11-31 Ø10 rue clip 2 Siderail laminate Number (left) Number (right) Dark blue HM-20-855 HM-20-854 Dark wood HM-20-762 HM-20-761 Light wood HM-20-752 HM-20-751 Wood HM-20-757 HM-20-756

95 Siderail assembly Item Number Name Quantity A YM-20-007 Head end right siderail 1 B HM-04-FTR005 Siderail assembly base metal 1 C YM-FUTUREALMKL-001- BY Aluminum siderail arm (white) 2 D HM-06-23 M6 x 10 mm countersunk bolt 6 E YM-HM-02-394 Siderail mechanism cover 1 left -mould 81 1 F YM-HM-02-363 Siderail mechanism cover 2 right - mould 81 1 G YM-HM-02-362 Siderail mechanism cover 3 center - mould 67 1 H HM-12-145 12-145 10 x 305 mm siderail pin 1 I HM-12-144 12-144 10 x 128 mm siderail pin 1 J HM-11-04 8 mm snap ring 2 K HM-18-27 Future side rail shock absorber 640015004 1 L HM-12-146 12-146 8 x 31 mm side rail pin 1 M HM-11-18 Q8 capped snap ring (DT/6671/43A) 2 N YM-HM-02-369 Siderail plastic main mechanism housing 1

www.stryker.com Siderail release latch assembly Item Number Name Quantity A HM-11-05 6 mm C shape snap ring DIN 6799 2 B HM-12-200 Ø8 x 98 mm siderail pin with snap ring slides 1 C HM-11-06 Size 4 snap ring 2 D HM-12–147 Ø5 x 98 mm siderail pin with snap ring slides 1 E HM-06–14 Ø3.5 x 13 mm Star screw 2 F HM-16–51 Hammer spring 1 G HM-02-370 Siderail mechanism plastic cover 1 H HM-02-374 Siderail release handle 1 I HM04-FTR007 Siderail release hammer 1 J HM-02-369 Siderail mechanism plastic shell 1