Inova WallBed Assembly Manual

Email: [email protected] Phone: 866.528.2804 WallBed | ASSEMBLY MANUAL PLEASE NOTE: Your Bed may look different than what is shown in the pictures and videos throughout this manual QUICK START GUIDE HELPFUL INFORMATION • Prior to opening your shipment, check and confirm the room is completely ready to receive the furniture (see “Room Readiness Checklist” below). • Place the parts in the room according to the sequence of the assembly steps to avoid double handling • The Hardware Box is located on the pallet and labeled “Hardware” • Hardware is packed by STEP #, not PART # • A large, contractor’s garbage bag is included in the Hardware Box for trash removal • All parts are labeled for easy identification • Labels will not be seen once the Bed is completely assembled; the part label is a sticker and can be removed if desired. • Each page of the assembly includes a “QR Code”, which is linked to a video for each step. To view, download a compatible QR Code App to view videos or go directly to YouTube (include link).

Email: [email protected] Phone: 866.528.2804 WallBed | ASSEMBLY MANUAL PLEASE NOTE: Your Bed may look different than what is shown in the pictures and videos throughout this manual ROOM READINESS CHECKLIST • Check room to confirm the ceiling, floor, and walls in the room are finished and completed • Select the wall and location in which the Bed will be placed • Measure the length of the wall and height of ceiling to confirm the Bed will fit TIP: You may want to remove existing baseboard that is located on the wall where the Bed will be installed. By removing the baseboard, it will allow for a tighter fit against the wall (custom units may already have a notch for baseboard – see shop drawings, if applicable). • Locate any electrical outlets on the wall that may be covered up by the Bed • Clear out any items in the room so you have a clear path to the wall and an open area to assemble the Bed • If the flooring is hard, lay down some furniture blankets, sheets of cardboard, or other cushioning material to prevent parts from being scratched. • Locate the mattress that will be used with this Bed; the specific mattress is required for proper adjustment of the Bed and completion of the assembly QUICK START GUIDE (CONT.)

Email: [email protected] Phone: 866.528.2804 WallBed | ASSEMBLY MANUAL PLEASE NOTE: Your Bed may look different than what is shown in the pictures and videos throughout this manual QUICK START GUIDE (CONT.) TOOLS NEEDED: Electric Power Drill #2 Phillips Bit #3 Phillips Bit (provided) #2 Square Bit (provided) 4mm Allen Wrench (provided) 4mm Allen Bit (provided) 9/16” Wrench #2 Phillips Screwdriver Hammer Pliers Utility Knife Vise Grips Flashlight QR Code Scanner App (To view videos) HARDWARE LIST: Bolts: H-075 Flat Head Bolts, 5/16” x 1-1/2” H-738 Flange Bolts 5/16” x 1-1/2” Screws: H-014s Euro Screws, 30mm H-016 Course Thread Screws, 2-1/2” H-019 Machine Screws, 10-32 x 3/4” H-065 Panel Screws, 50mm H-076 Flat Head Screws, 3/4” H-087 Pan Head Screws, 5/8” H-088 Machine Screws, 1/4”-20 x 1/2” H-107s Euro Screws, 13mm H-184 Auger Screws, 1” H-358 Button Head Screws, 5/16” H-425 Machine Screws, 25mm H-739 Cap Screws, 5/16” X 1-1/4” Nuts: H-086 Flange Nuts, 5/16” H-308 Acorn Nut, 5/16” Other: H-003 Wood Dowels H-008 Leveler Feet H-011 Minifix Pins H-067 Washers, 3/4”OD x 5/16” ID H-073 Pozi Euro Screws, 14mm H-074 Angle Brackets, 50mm H-077 Wide Angle Brackets H-085 Mending Plates H-146 Angle Brackets, 45mm H-210 Angle Bracket, 1” H-364 Sleeve Bearings Headoard Guides

WallBed: Hardware Overview H-016 H-076 H-011 H-075 H-067 H-065 H-014s H-003 H-073 H-019 H-008 H-074

WallBed: Hardware Overview, cont. H-077 H-210 H-107s H-085 H-184 H-088 H-087 H-146 H-086

WallBed: Hardware Overview, cont. H-425 H-739 H-358 H-738 H-364 H-308 Headboard Guide

shown. B. Screw the H-011 Minifix Pins into the small holes. C. Tap the H-003 Wood Dowels into the larger holes. STEP 1 OPEN BACK: Prepare Right Cabinet Side H-008 H-003 H-011 Use this version of Step 1 if your WallBed is an Open Back Model

shown. B. Screw the H-011 Minifix Pins into the small holes. C. Tap the H-003 Wood Dowels into the larger holes. STEP 1 CLOSED BACK: Prepare Right Cabient Side Use this version of Step 1 if your Sofa-WallBed is a Closed Back Model H-008 H-003 H-011

the H-011 Minifix Pins into the small holes of the Cabinet Front. Tap the H-003 Wood Dowels into the larger holes of the Cabinet Front. B. Prepare to attach Cabinet Bottom to Cabinet Front. C. Make sure all the Minifix Cams in the Cabinet Bottom have their arrows pointing towards the outside edge of the panel to allow the pins to slide into the Cams, as shown. D. Slide the Cabinet Bottom onto the Minifix Pins and Wood Dowels in the Cabinet Front, then tighten the Minifix Cams in the Cabinet Bottom. STEP 2: Attach Cabinet Front to Cabinet Bottom D Cabinet Front C H-003 H-011 B A D C Cabinet Bottom Cabinet Front A B Cabinet Bottom D C Cabinet Front Minifix Cam Arrow A B Minifix Cam Arrow D C A B

Use this version of Step 3 if your WallBed is an Open Back Model D A B Valance Cabinet Top D C A B Cabinet Top H-065 Valance D C Shelf Cabinet Back A B D C B Cabinet Back A Shelf H-065 A. Hold the Valance next to the Cabinet Top B. Screw the Valance to the Cabinet top with H-065 Panel Screws using a 4mm Allen Wrench. C. Hold the Shelf next to the Cabinet Back. D. Screw the Shelf to the Cabinet Back with H-065 Panel Screws using a 4mm Allen Wrench.

Use this version of Step 3 if your WallBed is an Closed Back Model D C A B Valance Cabinet Top D C A B Cabinet Top H-065 Valance D C B Closed Back A Shelf D C Closed Back B A Shelf H-065 A. Hold the Valance next to the Cabinet Top B. Screw the Valance to the Cabinet top with H-065 Panel Screws using a 4mm Allen Wrench. C. Hold the Shelf next to the Closed Back. D. Screw the Shelf to the Closed Back with H-065 Panel Screws using a 4mm Allen Wrench.

Use this version of Step 4 if your WallBed is an Open Back Model Cabinet Bottom Cabinet Side, Right Cabinet Front Cabinet Back Cabinet Top A. Lay the Right Cabinet Side from Step 1 on the floor as shown, using padding to protect it from getting scratched. B. Slide the Cabinet Front/Bottom Assembly onto the fittings in the Right Cabinet Side and tighten the Minifix Cams. C. Slide the Cabinet Back/Shelf Assembly onto the fittings in the Right Cabinet Side and tighten the Minifix Cams. D. Slide the Cabinet Top Assembly onto the fittings in the Right Cabinet Side and tighten the Minifix Cams.

Use this version of Step 4 if your WallBed is an Closed Back Model Cabinet Bottom Cabinet Side, Right Cabinet Front Cabinet Back H-065 Cabinet Top A. Lay the Right Cabinet Side from Step 1 on the floor as shown, using padding to protect it from getting scratched. B. Slide the Cabinet Front/Bottom Assembly onto the fittings in the Right Cabinet Side and tighten the Minifix Cams. C. Slide the Closed Back/Shelf Assembly onto the fittings in the Right Cabinet Side and tighten the Minifix Cams. D. Slide the Cabinet Top Assembly onto the fittings in the Right Cabinet Side and tighten the Minifix Cams. E. Screw the Cabinet Top to the Closed Back using H-065 Panel Screws using a 4mm Allen Wrench.

shown. B. Screw the H-011 Minifix Pins into the small holes. C. Tap the H-003 Wood Dowels into the larger holes. STEP 5 OPEN BACK: Prepare Left Cabinet Side H-008 H-011 H-003 Use this version of Step 5 if your WallBed is an Open Back Model

shown. B. Screw the H-011 Minifix Pins into the small holes. C. Tap the H-003 Wood Dowels into the larger holes. STEP 5 CLOSED BACK: Prepare Left Cabinet Side Use this version of Step 5 if your Sofa-WallBed is a Closed Back Model H-008 H-003 H-011

arrows pointing to the nearest edge of the panels. B. Lift the Left Cabinet Side, flip it over, and place it on the partly assembled cabinet as shown. You may need to shift the parts slightly to get the dowels and pins to line up with the holes. C. Tighten all the Minifix Cams as in Step 4. D. The Bed Cabinet is now complete and ready to stand up. STEP 6 OPEN BACK: Attach Left Cabinet Side to the Cabinet Assembly Cabinet Bottom Cabinet Front Cabinet Back Cabinet Side, Left Cabinet Top Use this version of Step 6 if your WallBed is an Open Back Model

arrows pointing to the nearest edge of the panels. B. Lift the Left Cabinet Side, flip it over, and place it on the partly assembled cabinet as shown. You may need to shift the parts slightly to get the dowels and pins to line up with the holes. C. Tighten all the Minifix Cams as in Step 4. D. The Bed Cabinet is now complete and ready to stand up. STEP 6 CLOSED BACK: Attach Left Cabinet Side to the Cabinet Assembly Use this version of Step 6 if your Sofa-WallBed is a Closed Back Model Cabinet Bottom Cabinet Front Closed Back Cabinet Side, Left Cabinet Top

people for safety. Carefully lay the Cabinet over as shown, using padding on the floor to protect the cabinet from being scratched. B. Raise the Cabinet as shown. C. Carefully “walk” the standing Cabinet so that it is about two feet from the wall where it will be placed when it is finished. STEP 7 OPEN BACK: Lay the Cabinet Over on its Back and then Stand it Up C A D B A B C D A C B D

the front holes are exposed. From the outside face of the Left Cabinet Side insert a H-075 Bolt through one of the front holes and align the bolt with the mating hole in the Left Mechanism. Hand turn a H-086 Nut on the bolt until it begins to thread, but do not tighten it completely. Insert another H-075 Bolt through one of the two rear holes. Align and hand turn another H-086 Nut on the bolt until it begins to thread, but do not tighten it completely. After all five H-075 Bolts are inserted through the outside face of the Left Cabinet Side, and all five H-086 Nuts are hand threaded on the bolts, proceed to tighten all the H-086 Nuts tightly with a crescent wrench, 1/2” box wrench, or 1/2” socket. B. Repeat “A” for the Right Spring Mechanism. STEP 8: Attach the Lift Mechanisms to the Bed Cabinet H-075 H-086 Mechanism Arm A Cabinet Side, Left Mechansim, Left B A H-075 B H-086 Cabinet Side, Right Mechanism Arm Mechanism, Right

against the wall where it will be installed. Do a preliminary check for squareness by measuring diagonally from corner to corner across the face of the cabinet. Use a step ladder to access the wall above the Cabinet Top and locate studs or other solid structural members to which you can fasten the H-074 Angle Brackets. TWIN SIZE requires two H-074 Angle Brackets. One should be located on each side of the centerline. FULL & QUEEN SIZES require three H-074 Angle Brackets. One should be located near the center and the other two should be located near the sides of the Cabinet Top as shown. KING SIZES requires four H-074 Angle Brackets. Two should be located on each side of the centerline. B. Drive two H-016 Flathead Screws through each Angle Bracket and into each solid framing member in the wall. Drive two H-076 Flathead Screws through the angle brackets and into the Cabinet Top. CAUTION! WallBeds must be securely attached to wall structure before proceeding, to ensure safe and smooth operation! STEP 9: Attach the Cabinet to the Wall A Wall studs H-074 B A H-074 H-076 Wall studs H-016 B

Rail using H-073 Euro Screws, as shown. B. Attach the M-222 Side Angle to the Left Side Rail using H-073 Euro Screws, as shown. STEP 10: Prepare Left and Right Side Rails H-073 M-222 A Side Rail, Left B H-073 M-222 Side Rail, Right A B

on the carpet or other padded surface. Make sure the area is clear of any hardware or debris that can cause damage. Align the holes of the Left Side Rail Angle with the holes of the Left Bed Panel and attach them by screwing the H-088 Bolts through the Side Angle and into the Bed Panel. Take care to ensure that the parts are oriented so that the Threaded Inserts the Side Rail are near the notched end of the Bed Panel. Proceed with the same process for the Right Side Rail. STEP 11 PLAIN BED PANEL: Side Rails to Bed Panels Notched End Threaded Inserts Side Rail, Left Threaded Inserts H-088 Bed Panel, Left H-088 Side Rail, Left Bed Panel, Right Use this version of Step 11 if your Sofa-WallBed has a Plain Bed Panel

on the carpet or other padded surface. Make sure the area is clear of any hardware or debris that can cause damage. Align the holes of the Left Side Rail Angle with the holes of the Left Bed Panel and attach them by screwing the H-088 Bolts through the Side Angle and into the Bed Panel. Take care to ensure that the parts are oriented so that the Threaded Inserts the Side Rail are near the notched end of the Bed Panel. Proceed with the same process for the Right Side Rail. STEP 11 RECESSED BED PANEL: Side Rails to Bed Panels Use this version of Step 11 if your Sofa-WallBed has a Recessed Bed Panel Notched End Threaded Inserts Lower Bed Panel Side Rail, Left Bed Panel, Left Bed Panel, Right Threaded Inserts H-088 H-088 Upper Bed Panel Side Rail, Left

Rail using H-073 Euro Screws, as shown. STEP 12: Prepare Foot Rail A M-19 Foot Rail H-073

the holes of the Bed Panels and attach them by screwing the H-088 Bolts through the Foot Rail Angle and into the Bed Panels. Take care to ensure that the parts are oriented so that the Foot Rail is at the opposite side of the Bed Panel notched ends. STEP 13 PLAIN BED PANEL: Attach Foot Rail to Bed Panels Foot Rail Side Rail, Left Bed Panel, Left H-088 Bed Panel, Right Side Rail, Right Notched End Use this version of Step 13 if your Sofa-WallBed has a Plain Bed Panel

Use this version of Step 13 if your Sofa-WallBed has a Recessed Bed Panel Foot Rail Side Rail, Left Upper Bed Panel H-088 Bed Panel, Left Bed Panel, Right Side Rail, Right Notched End A. Align the holes of the Foot Rail Angle with the holes of the Right, Upper, and Left Bed Panels and attach them by screwing the H-088 Bolts through the Foot Rail Angle and into the Bed Panels. Take care to ensure that the parts are oriented so that the Foot Rail is at the opposite side of the Bed Panel notched ends.

connecting the H-077 Wide Angle Brackets to each corner with H-107s Flat Head Euro Screws, as shown. STEP 14: Attach Foot Rail to Bed Panels H-077 H-107s H-107s Side Rail Foot Rail

other using the H-085 Mending Plates and H-087 Pan Head Screws, making sure that the top edge of the panels are well aligned when installing the H-085 Mending Plates. STEP 15 PLAIN BED PANEL: Attach Right and Left Bed Panels Bed Panel, Left Bed Panel, Right H-087 H-085 Use this version of Step 15 if your Sofa-WallBed has a Plain Bed Panel

Use this version of Step 15 if your Sofa-WallBed has a Recessed Bed Panel Lower Bed Panel Bed Panel, Left H-085 H-087 Mirror Panel Bed Panel, Right Upper Bed Panel H-184 Foot Rail A. Lay the mirror Panel face down on the rectangular opening in between the Bed Panels, and line up the holes of the Mirror Panel with holes in the Bed Panels. Make sure that the ends of the Bed Panels are well aligned. Attach the Right, Lower, and Left Bed Panels to each other using the H-085 Mending Plates and H-087 Pan Head Screws.

Rail using H-019 Screws, as shown. B. Align the holes of the Head Rail Angle with the holes of the Bed Panels and attach them by screwing the H-088 Bolts through the Head Rail Angle and into the Bed Panels, as shown. C. Attach the Head Rail to each Side Rail by connecting the H-077 Wide Angle Brackets to each corner with H-107s Flat Head Euro Screws, as shown. STEP 16 PLAIN BED PANEL: Prepare and Attach Head Rail to Bed Panels Use this version of Step 16 if your Sofa-WallBed has a Plain Bed Panel Head Rail M-19d H-019 A C D B Side Rail, Left H-088 Head Rail Side Rail, Right D A C B H-077 D Head Rail Side Rail, Right C A B

Use this version of Step 16 if your Sofa-WallBed has a Recessed Bed Panel Head Rail M-19 H-019 A C D B Side Rail, Left H-088 Head Rail Side Rail, Right D A C B H-077 D Head Rail Side Rail, Right C A B A. Attach the M-19 Short bed Angle to the Head Rail using H-019 Screws, as shown. B. Align the holes of the Head Rail Angle with the holes of the Bed Panels and attach them by screwing the H-088 Bolts through the Head Rail Angle and into the Bed Panels, as shown. C. Attach the Head Rail to each Side Rail by connecting the H-077 Wide Angle Brackets to each corner with H-107s Flat Head Euro Screws, as shown.

outside of the Side Rail. Thread a H-086 5/16” nut on the end of the bolt just enough so that the end of the bolt protrudes from the nut. There should be about 1/4” of bolt threads visible between the underside of the head of the Bolt and the outside face of the Side Rail. In the #3 hole, insert a H-739 Cap Screw from the outside face of the Side Rail and thread on a H-086 5/16” Nut from the other side. This nut should be tightened by hand so that the head of the Cap Screw is snug against the outside face of the Side Rail. STEP 17: Attach Mounting Hardware to the Side Rails Head Rail H-086 Hole #3 H-086 Hole #2 Side Rail H-739 Hole #1 H-738

over on its side, as shown. B. Carefully support the Bed Platform on its side. Attach the handles on each side of the Bed Panels using the H-425 Machine Screws. STEP 18: Attach the Handles to Bed Platform B A Handle H-425 A B

tension arm and use it bring the arms outward against the initial tension of the springs. When they are pulled near the angle shown, swivel the Arm Locks over to brace against Hex Bolt ‘A’. There will be a lot of tension on the Tension Arm. CAUTION! There will be a lot of tension on the Tension Arms. We recommend that two people handle this procedure: one pulling and holding the tension arm with both hands, while the other sets the arm lock. When setting the arm lock, avoid reaching behind the tension arm and be very careful to avoid getting pinched. STEP 19: Pull down the Mechanism Arm Hex Bolt 'A' Tension Arm Arm Lock PVC Pipe

and between the Sofa Arms as shown. STEP 20: Walk the Bed Platform towards the Bed Cabinet Cabinet Side Bed Platform Head Rail

Hex Bolts in Hole #1 are a few inches above the Tension Arm Slots. Carefully fit the bed platform between the two Tension Arms so that the Hex Bolts in Hole #1 slide into the Tension Arm Slots. Slowly tilt the Bed Platform back to allow the Cap Screws in Hole #3 to be seated against the notches at the bottom of each Tension Arm. Please note that this image is made transparent to show the Mechanism Arm components. STEP 21: Locate the Bed Platform in Bed Cabinet Hole #2 Cap Screw, Hole #3 Notch Tension Arm Slot Bolt, Hole #1 Side Rail

the inside face of both Side Rails and into the Tension Arms. It may help to have a helper hold the bed in the position near 45° to allow for more access. Tighten the H-086 Flange Nuts onto the H-738 Hex Bolts at Hole #2. Tighten the Hex Bolts and Flange Nuts at Hole #1. Tilt the Bed platform down until it is horizontal. You will hear a click as the Arm Locks disengage. Holding the upper edge of the Bed Platform, gently let the Bed close. Please note that this image is made transparent to show the Mechanism Arm components. CAUTION! For the rest of the assembly, the bed will be under spring tension as you raise and lower it. While you are working on it have someone hold it down for you so it doesn’t rise suddenly. Before continuing, be sure that the bolts in Holes #1 and 2 are tightened completely. STEP 22: Mount Bed Platform in Bed Cabinet H-738 Cap Screw, Hole #3 Hole #2 Bolt, Hole #1 H-086 Side Rail

square welded nuts on the Leg Components to the Crossbar, then securing them together together with H-358 Button Head Bolts. Ensure the Leg Components are aligned with the bent tabs pointing towards each other. B. Align the Flipover Leg to the Bed Platform, as shown. Use H-358 Button Head Bolts (through the H-364 Sleeve Bearings) to attach the Flipover Leg to the Side Rails with H-067 Washers for spacing. as shown. Tighten the Bolts into the T-Nut. C. At the inside face of each Side Rail, position a H-067 Washer over the end of the Button Head Bolt, and then tighten a H-308 Acorn Nut to the end of the Button Head Bolt. STEP 23: Assemble Flipover Leg Crossbar Bent Tab H-358 Leg Component Side Rail H-308 H-067 T-Nut H-067 Foot Rail H-364 H-358

Platform so that the edge with the loop pull is in the center of the Bed Platform and the opposite edge is against the Headrail. Lay down the second Box Spring Panel into the Bed Platform so that the edge with the loop pull is in the center of the Bed Platform and the opposite edge is against the Footrail. Firmly press the Box Spring Panel edges down and visually inspect the Box Springs to ensure all edges of the Box Spring Panels are parallel to and supported by the Bed Platform assembly. B. Locate an Angle Bracket at the middle of each Box Spring Panel edge that abuts a Side Rail. Once located, fasten the H-146 Angle Brackets to the Side Rails with H-087 Screws, as shown. STEP 24: Install Box Springs into Bed Platform B Box Spring A Box Spring H-146 H-087 B Box Spring A

the Bed Platform. B. Locate the Headboard so that the hinge holes align with the holes of the Head Rail. It is best to start a H-014s Euro Screw at each end of the hinge. Once the hinge is aligned this way, you can finish inserting all of the Euro Screws and tightening them. C. Locate the Headboard Guide Assembly on the back of the Headboard. Align the 4 holes of each Headboard Guide with the 4 holes on each end of the Headboard. Attach the Headboard Guide to the Headboard with H-087 Pan Head Screws, as shown. D. Pull the Guide Cable away from the Headboard so that Guide Pins are positioned in towards the center of the Bed, then pivot the Headboard toward the back of the Bed Cabinet. Once the Guide Pins are aligned with the Guide Tracks, release the Cable so that the Pins are positioned out into the Tracks. STEP 25: Put the Mattress in place & Attach the Headboard to the Head Rail A C B Mattress D H-014s A Headboard C B D Headboard Guide Headboard A C D B A C B D

covers down over the spring mechanisms lining up the tabs in the covers with the spaces in the mechanisms. B. Secure the mechanism covers in place with an H-210 Angle Bracket and H-087 Screw. The bracket should be placed on top of the mechanism cover and the screw should be used to attach the angle bracket to the Cabinet Side. C. It is important that pillows are not stored in the bed when closed. We leave it to your discretion whether or not to place the warning sticker on the Shelf. STEP 24: Install Box Springs into Bed Platform Mechanism Mechanism Cover A C B D H-210 Mechanism Cover H-087 A C B D "No Pillows" Sticker Shelf A C B D

support position to its stored position when the bed is not in use. As the bed platform is raised, a housekeeper or guest can grab the square crossbar of the frame and simply lift it up and over into position. STEP 25: Raise the Bed Platform and Pivot the Flipover Leg Flipover Leg Bed Platform

Email: [email protected] Phone: 866.528.2804 WallBed | ASSEMBLY MANUAL PLEASE NOTE: Your Bed may look different than what is shown in the pictures and videos throughout this manual HOW IT WORKS HOW IT MOVES UP AND DOWN: The mechanisms that allow the WallBed to move up and down are spring-loaded and located inside face of each pier. As the WallBed is lowered down, gravity is naturally starting to pull it down. The springs “kick in” and provide enough resistance to avoid it from coming down too quickly. As the WallBed is raised upward, gravity is resisting, To make it easier to lift, the springs releases tension, assisting the bed as it is raised. TO LOWER THE WALLBED: Handles are located on the outside of the Bed Cabinet (on the Bed Panels) for use to lower the Bed. TO RAISE THE WALLBED: At the corner of the bed platform, place hands underneath and lift. Start walking toward the bed cabinet to close. Once at half-way, grab a handle and guide into the cabinet.

Email: [email protected] Phone: 866.528.2804 WallBed | ASSEMBLY MANUAL PLEASE NOTE: Your Bed may look different than what is shown in the pictures and videos throughout this manual HOW IT WORKS (CONT.) 1. To adjust the number of springs, you will need to temporarily detach the Bed Cabinet from the wall. Use a step ladder to access the top of the Cabinet, and temporarily remove the H-o76 Flat Head Screws that attach the Angle Brackets to the Cabinet Top (Refer to Step 9). 2. While the Angle Brakets remain attached to the wall, “walk” the Cabinet forward until it is around two feet from the wall. 3. Working behind the Cabinet, add or remove springs from the spring mechanisms as needed. The top and bottom springs are installed with the hooks facing inward so they are a little easier to remove. The final arrangement of springs should be symmetrical above and below the center of the mechanism. for example, if you start with (8) springs, the center space will be empty. If you remove a spring, you should take it off the top, but you should also move the bottom spring to the center space. Ideally the left and right spring mechanism should have the same number of springs. HOW TO ADJUST TENSION: STEPS FOR ADJUSTMENT: To adjust the tension of the Sofa-WallBed: The factory has installed the proper number of springs based on our estimates of the weight of typi- cal mattresses. Your mattress weight may vary from these estimates. With the springs provided, the bed platform should be very easy to raise and lower. If it is too light, it will float up a little instead of stay- ing down in the bed position. In this case you will need to remove one of the springs. If it is too heavy, it will be too difficult to lift and you will need to add a spring.

Email: [email protected] Phone: 866.528.2804 WallBed | ASSEMBLY MANUAL PLEASE NOTE: Your Bed may look different than what is shown in the pictures and videos throughout this manual STEPS FOR ADJUSTMENT (CONT.): HOW IT WORKS (CONT.) 4. Push the Cabinet in place against the wall and reattach the H-076 Flathead Screws through the Angle Brackets and into the Cabinet Top. The Bed Cabinet must be secured to the wall structure, as in Step 9! Test the raising and lowering of the bed.

Email: [email protected] Phone: 866.528.2804 WallBed | ASSEMBLY MANUAL PLEASE NOTE: Your Bed may look different than what is shown in the pictures and videos throughout this manual TROUBLESHOOTING HOW CAN I ACCESS BEHIND THE WALLBED? If you need to access to the area behind the bed, you most likey do not have to remove it from the wall. The Headboard does release, allowing access behind the Bed. TO LOWER THE HEADBOARD: Have someone lower the bed about halfway and hold it there. On the back of the Headboard there are guide pins located on the left and right, with a cable stretched between them. These pins extend into the track located on each side of the cabinet, guiding the Headboard movement as the bed is raised and lowered. Reach behind the Headboard and locate the cable. Pull the cable upward to release the pins on both side and pivot the Headboard forward to the mattress. Make sure you keep holding tension on the cable as you pivot the Headboard to prevent the pins from scratching the inner faces of the Cabinet Sides. At this point, the Bed can be lowered down completely. To re-engage the pins, pull upward on the tension cable and raise Headboard, until the pins are aligned with the track. Release the cable. The pins should snap out into position, resetting the headboard for use. REMOVING BED FROM WALL: With another person, “walk” each side of the Cabinet away from wall. TIP: You may want to place moving pads underneath cabinet (with another person, tip cabinet slightly to place pad). MY WALLBED IS MAKING A CREAKING NOISE If any of the hinges or other parts of the mechanism on the WallBed creak, spray

Email: [email protected] Phone: 866.528.2804 WallBed | ASSEMBLY MANUAL PLEASE NOTE: Your Bed may look different than what is shown in the pictures and videos throughout this manual TROUBLESHOOTING (CONT.) them with a dry silicone-type lubricant, available at most hardware stores. Although this type of lubricant should not damage the wood panels, be careful not get any on the bed covers or mattress. I CAN’T RAISE OR LOWER THE BED PLATFORM If there is any binding or difficulty raising or lowering the bed, it is possible that a foreign object has become lodged in the spring mechanism. If there is no obvious culprit, call Inova customer service for assistance in troubleshooting the issue. THE BED PLATFORM WON’T CLOSE COMPLETELY If the Bed Platform is pivoted up and won’t completely close to its “Up Position”, it is possible there is an object lodged between the back of the Cabinet Front and front of the Bed Platform. If there is no obvious obstruction, call Inova customer service for assistance in troubleshooting the issue. CARE & MAINTENANCE INFORMATION Please refer to your Welcome Booklet for detailed information on Care & Maintenance NEED TO DISASSEMBLE AND MOVE THE WALLBED Reverse assembly steps from manual TIP: Bag and label hardware per Step. This will be very helpful when reassembling the WallBed.

Email: [email protected] Phone: 866.528.2804 WallBed | ASSEMBLY MANUAL PLEASE NOTE: Your Bed may look different than what is shown in the pictures and videos throughout this manual I HAVE A BROKEN PART THAT NEEDS TO BE REPLACED Locate your order # (label located inside Bed Platform) Take photos of broken part and Bed overall Upload and Email Us with description of issue, photos, and include your order # for easy identification. TROUBLESHOOTING (CONT.)

Email: [email protected] Phone: 866.528.2804 WallBed | ASSEMBLY MANUAL PLEASE NOTE: Your Bed may look different than what is shown in the pictures and videos throughout this manual FEEDBACK WELCOME FEEDBACK WELCOME: This assembly manual was created with you in mind. Over the years, we have been asked common questions and received important feedback on our products and services. With great care, and through continuous improvement and learning, we have incorporated the answers and feedback within these manuals. We hope you find them useful and easy to use! With this said, if there is any outstanding question that you have, please do not hesitate to contact us. We also welcome any and all feedback about our product and your experience with it. Email us at [email protected] or call us at 866.528.2804. We hope you enjoy your Inova WalBed for many years to come! THANK YOU.