Voyager DVR4100 Operation & User’s Manual

User Manual Thank you for purchasing our product. Please read instructions before operation. Change without Notice.

SPECIFICALLY DESIGNED FOR OUTDOOR USE TO RAIN OR MOISTURE. CAUTION : To reduce the risk of electric shock, do not expose this apparatus to rain or moisture. Only operate this apparatus from the type of power source indicated on the label. The company shall not be liable for any damages arising out of any improper use, Even if we have been advised of the possibility of such damages. Graphic Symbol Explanation The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user of the presence of insulated dangerous voltage within the product’s enclosure that may be sufficient magnitude to constitute risk of electrical shock to persons. This exclamation point within an equilateral triangle is intended to alert the user of the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. All lead-free products offered by the company comply with the requirements of the European law on the Restriction of Hazardous Substances (RoHS) directive, which means our manufacture processes and products are strictly “lead-free” and without the hazardous substances cited in the directive. The crossed-out wheeled bin mark symbolizes that within the European Union the product must be collected separately at the product end-of-life. This applies to your product and any peripherals marked with this symbol. Do not dispose of these products as unsorted municipal waste. Contact your local dealer for procedures for recycling this equipment. Attention: installation should be performed by qualified service personnel only in accordance with the National Electrical Code or applicable local codes. Safety Precautions CAUTION RISK OF ELECTRIC SHOCK

conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received including interference that may cause undesired operation." WARNING This Equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help.  You are cautioned that changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment.

1. Package contents ……………………….. 5 2. Product overview ……………………….. 7 3. Physical connection ……………………….. 10 4. Setup ……………………….. 16 5. DVR operation via video out ……………………….. 21 6. DVR operation via browser ……………………….. 35 7. Configuration ……………………….. 47 8. Register Server Installation instructions ……………………….. 52 9. Vehicle Management Software (VMS) ……………………….. 63

Description Picture Power cable (6 pin/6m) + 5A fuse X 2 I/O cable G-Mouse (Male/5m) Wifi antenna (Female) Remote Controller + battery Screw x 6 SSD rack locker key

pieces) External Indicator (optional) CD Contents Description Voyager Player Voyager VMS RegisterServer_Setup ServerDBInstall

Front Panel DVR4100 (※ Front panel USB port recommended only for USB storage, mouse recommended use the back Cable wire’s USB port ) ※ Notice : The warning sticks in front panel. The content is show as below: Back Panel DVR4100: with 3G (4G) / WIFI function

I/O cable pin definition Female connector Pin number Description 1 +12V 2 GND 3 Audio 4 Video ① ② ③ ④

Lock Lock the DVR system need a password to unlock it Panic Panic record button Menu Go to ‘MENU’ mode to setup the system Search Search recorded video Backup Backup the recorded data to other device Direction (▲,▼,◀,▶) Move the cursor ENTER Select sub item in system setup mode ESC Exit the dialog window

SSD installation ① Please insert the key in the front of the device and turn counterclockwise 90° to unlock. ② Loosen the two screws and take off the cover. ③ Pull the rack out to install SSD.

the four screws. ⑤ Set the SSD back to DVR. Please be sure you it is locked. After you installed the SSD, please put the rack back into the mobile DVR, tighten the two front screws and lock the rack. If the lock is not correctly done, the system won’t be started up and the power led will flash. ※When SSD is installed, the bottom screen will display an Icon as .

※When SD card is installed, the bottom screen will display an Icon as . Please refer to below photo. ※ DVR only supports SD card formatted by FAT32. If use other format to record files, read/write problems may happen. ※ If the SD card is damaged, DVR will not be able to perform normal functions as recording, playback and so on. For the time being, please use computer to format the SD card. If it is still a problem, please contact the manufacturer of SD card for overhauling or data rescuing. ※ Supports SD, SDHC. 1. Shut the power down 2. Loosen screws and open the cover 3. Insert SD card in the slot properly Icon and storage information will be shown here.

When you purchase your SIM card to your telecom provider, please make sure that it meets one of the following standards in order to work: GSM 850 900 1800 1900 WCDMA 850 1900 2100 ① Loosen 4 bolts of the top cover and open it. ② Pull the SIM card socket.

④ Put the lid back and push it to lock. Indicator light LED Color Description Always ON Always OFF Flashing Red Record recording (Normal/Event) No recording Warning: device can’t record、Vloss or SSD Initial fail Green Power System ready Power off System booting

For your information ground and power + cable are protected with a 5A fuse. Note that, do not pull the power connector when the DVR is recording to avoid the SSD be damaged. First unplug all cameras, wait that yellow led turn off then unplug the power. Event Box description + - CAR BATTERY DVR Connect to ACC of your car

cable Link the notebook to the DVR with the LAN cable Under windows 7 On the desktop bottom right, right click mouse on network icon then select open network and sharing center Then on the left select Change adapter settings Choose your lan wired connection then mouse right click and select properties Icon Description Color Always ON Always OFF Flashing Record Red recording (Normal/Event) No recording Warning: device can’t record、Vloss or SSD Initial fail Power Green System ready Power off System booting

Assign an IP address to your notebook as the DVR default IP is 192.168.1.99

Internet Explorer setting Our device supports Internet Explorer 7, 8, 9(32bits) and 10,11(32,64bits) The default IP address of the mobile DVR is 192.168.1.99 In order to install the active X you need to change your Internet Explorer settings Open Internet Explorer, Click the Tools button, and then click Internet Options. Click the Security tab, and then click a security zone Trusted sites. Click Sites.

the below option ‘require server verification’ is disabled Click Add and close. Then turn the Security level to Low and press apply Return to Internet Explorer main page Press Install The icon must be in blue color then please login in the DVR Default administrator username/password is “admin”/ “1111” Default guest username/password is “guest”/ “1111” If you don’t operate the vehicle dvr after a period of time (30 minutes) you will be automatically logged out, then you need to login again with your account and password You will have a pop up message

 Channel: 4 channels total. From 1~4.  Start Record: “ON”, “OFF”  Frame Rate: 1fps~30 fps (NTSC)/ 1fps~25 fps (PAL)  Quality: 5 options can be selected; “highest”, “high”, “normal”, “low”, “lowest”.  Resolution: “320X240”, “720X240”, “720X480”. (NTSC) “320X288”, “720X288”, “720X576”. (PAL)  Audio: “ON”, “OFF”  Post Record: can be setup from “OFF”, “30 sec”, “1 min”, “2 min”, “5 min”, “15 min”, "30 min”, “1 Hour”. Finally, “Apply ALL”, “Save”, & “Exit”.  Ignition Off: postpone time can be set from ”30 sec”, “5 min”, “10 min”, “15 min”, “20 min”, “25 min”, “30 min”, “35 min”, “40 min”, “45 min”, “50 min”, “55 min”, “60 min”. After setup this section, click “Save” and this page will be automatically exited.  Streaming:  Frame Rate: From 1~15.  Quality:”Highest”, “High”, “Normal”, “Low”, “Lowest”. Device:  Camera Setup  Camera: 1 ~ 4  Camera Title: edit the camera name.  Color Setup Brightness: 0~10 Contrast: 0~10 Saturation: 0~10 Hue: 0~10 Mirror: "ON","OFF" Flip: "ON","OFF" “Click “ X “, return to Device page..  Storage: Installed SSD & SD information will be located and listed here. Including SSD’s “Name”(The name of SSD will be Main storage), “Size”, “Format”. After click “Format” pop-out message would ask & make sure user want to do the “Format” action. Check “Yes” or ”No” button for your choice. Meanwhile, the SSD overwirte action can be set when SSD was fully used for the record file. Please note that if you insert a SSD that has been used prior, the SSD will be formatted. ※ SSD as main storage device for continuos recording data & SD as event data storage device  Battery detector:  Enable: “ON”, “OFF”

※ Battery voltage detection function: when the voltage is too low, will alert user.  Buzzer:  Sensor: “OFF(No suggest)”, “Critical”, “Warning”. Default is OFF  Video Loss: “OFF(No suggest)”, “Critical”, “Warning”. Default is Critical  SSD: “OFF(No suggest)”, “Critical”, “Warning”. Default is Critical  G- Sensor : “OFF(No suggest)”, “Critical”, “Warning”. Default is Critical.  Event Setup: Including the “Video Loss”, “Motion”, “Sensor”, “Speed Event”, “G-Sensor”.  Video Loss:  Camera: 1~4  Enable: “ON”, “OFF” . If the status is “ON”, below 3 items can be setup at the same time.  Delay Time: OFF, “1 sec”, “2 sec”, “3 sec”, “4 sec”, “5 sec”, “6 sec”, “7 sec”, ”8 sec”, “9 sec”, “10 sec”.  E-mail: setup the receiver’s E-mail.  Alarm out: Click the icon if need.  Motion:  Camera: specific 1~4 camera can be set.  Enable: “ON”, “OFF”.  Delay Time: “OFF”, “1 sec”, “2 sec”, “3 sec”, “4 sec”, “5 sec”, “6 sec”, “7 sec”, “8 sec”, “9 sec”.  E-mail: “ON”, “OFF”  Alarm Out: click the box if need.  Event Record: ”ON”, “OFF”  Event Popup: “ON”, “OFF”  Sensitivity: 1~5  Area Setup: setup the area we want to monitor. In green color area, “motion function is turned on,  Sensor:  Sensor:1 ~ 8  Enable: ON/OFF  Delay Time: 0 ~ 9 seconds  Priority: 1 ~ 8  Email: ON~ OFF  Alarm out: click the box if need  Event record: 1 ~ 4

Speed Event Enable: ON/OFF Unit: you can choose between Km/h or MPH Type: High speed / Low speed Enable: ON/OFF Threshold: 1 ~ 300 Delay Time: define the length of the buzzer after each motion detection OFF ~ 9 seconds Email: can send an email to predefined address in case of the event Alarm out: in case of detection, DVR will send a signal via alarm out like a buzzer Event Record: 1 ~ 4. G Sensor Enable: ON/OFF Threshold : OFF ~ 5g Vibration Boot : ON / OFF Delay Time: define the length of the buzzer after each motion detection OFF ~ 9 seconds Email: can send an email to predefined address in case of the event Alarm out: in case of detection, DVR will send a signal via alarm out like a buzzer Event Record: 1~4 ※ If GPS mouse has already connect to the device, the bottom screen will display this ICON

For static IP you need to key manually the IP, GATEWAY and NETMASK. For DHCP, the DVR will retrieve the information from the network Net Service Center IP: VMS server IP address. Center Port: default is 8788 but can be changed according to customer need Register timing: “OFF”, “10 sec”, “30 sec”, “60 sec”. Http Port: default is 80 but can be changed according to customer need Streaming Port: default is 554 but can be changed according to customer need Messenger Port: default is 1999 but can be changed according to customer need DNS: if the user specifies a DNS, it will help the CMS to find the ip of the DVR more faster via using 3G connection Stream: Telnet: “ON”, “OFF”. ※ Warning: make sure that these port are open in your router if you use a LAN network ※ If use LAN connect network, the bottom screen will display this ICON

Port: E-mail service port. SSL: ON/OFF Sender: sender mail Recipient: recipient mail Enable SMTP Auth: ON/OFF (some mail server need user authentication.) Account: mail service account. Password: mail service password. E-mail test: Due to the authorization problem, some mail server will not work properly. Please click the “E-mail test " button to test your mail server. If you don't receive the email, please contact with your MIS department or change another mail server and try again.

Enable: ON/OFF Access Point Name (APN): default is Internet. Access Number: default is *99# Username Password ※ If use 3G (or 4G) to connect network, the bottom screen will display this ICON WIFI Enable: ON/OFF SSID: input your WIFI AP name. Authentication: input your WIFI AP connect key. ※ If use WIFI to connect network, the bottom screen will display this ICON Remote connection supports up 2 people log in Example: x1：Represent there 1 person is using LAN connection now. x1：Represent there 1 person is using 3G(or 4G) connection now. x1：Represent there 1 person is using WIFI connection now.

account Group: Administrator/Guest Password User can setup administrator and guest password System tools Time Setup Date: Year- Month-Day Time: Hour-Minute-Second Display format available: MM/DD/YYYY, DD/MM/YYYY, YYYY/MM/DD Time format: 12 hour or 24 hour Daylight Saving: ON or OFF, after user selects the time zone, if daylight saving is enable, the DVR will automatically adjust the time GPS Time Calibration : Time Zone:

CVBS Y Adj: 0~9 CVBS Height adjustment: 0 ~ 9 CVBS Width adjustment: 0 ~ 9 Video format: PAL ~ NTSC You can enable or disable the following function by click or unclick them  System time  Channel title  Record Icon  Motion Icon  Alarm Icon  Save split mode

formatted in FAT32, insert in the USB port and click upgrade, you will notice following message Message Description waiting Starts the upgrade process Are you sure to upgrade? The USB key is being initialized, the yes/no will appear after few second search file If press yes it will look for the file in the USB key upgrade system please wait 1/4 (3/3) Upgrade complete. the system will reboot Press ok to reboot the device ※Notice: After the new firmware update, we recommend user to reset the DVR to factory default. Truck Info Setup User can add vehicle info such as: device number, company name, driver name, vehicle number Import User can import or restore setting Message Description waiting Starts the process Are you sure to import config The USB key is being initialized, the yes/ no will appear after few second Import complete! The system will reboot Press ok to reboot the device

Message Description waiting Starts the process Are you sure to export config ? The USB key is being initialized, the yes/ no will appear after few second Export finish! Press ok to leave the export mode Notice: The export file name is Config, you can rename it for archive purpose but you must rename it as Config if you want to use it to restore setting in your combo DVR Default This enables user to reset setting to default. Message Description waiting Starts the process Are you sure to reset default? Yes to validate, No to cancel Reset Default Finish! Press ok to reboot the system

Network Info: DVR’s IP address, MAC address, netmask, gateway Storage info: Status mention if the SSD is correctly working, its model name and storage utilization GPS info: Time, Longitude, Latitude, Speed, Height, Direction, Viewable, In use, Fixed status. ※ The GPS function is only for satellite positioning. 3G info/4G info: Enable, Signal, IP address, Net Mask, Gateway Wifi info: Enable, SSID, IP address, Netmask, MAC address, Gateway, Signal

Search Backup User can make a backup of specific period on any USB device such USB key, external USB SSD Time Search Key in specific time to playback the data, select the camera and click go search ※ When you use the calendar to select a date, blue typeface indicates that there is recorded video for that day. Event List User can select the channel, define start and end time, and click the search Icon. Log List Select the channel Define start and end time. DVR4100 available: system, motion, sensor, video loss, network remote access And click on Search it will display the results, and then select the event to play it back Backup Mouse right click  Backup Insert your USB solid disk and Select the channel you want to backup, define the time period and after the OSD display your USB key free space memory, press GO BACKUP !

or from 1 to 15 Select the channel you want to listen by selecting the channel or press mute to disable sound Split screen User can choose 1、2、3 or 4ch to display Playback Mouse right click  Playback User can playback last recorded file Fast Rewind Pause Play Fast Forward Slow forward: it will forward frame by frame Stop and return to main display Split screen Volume adjustment

Live preview After you log in, you will access to live picture , there are 5 areas: 1 is all the function of the DVR function are same as main video out 2 is the main display of the camera, to see a camera in full screen, just double click on it. To return to quad mode, please go to VIDEO/LIVE 3 is the log out function and language setting, you can choose English, Chinese, Francais and Portugal. 4 is the information regarding the system (firmware, plugin) and regarding the vehicle (serial number, company, driver name, licence plate number). 5 is audio on/off

Playback After you make sure that you have enabled video recording, you can playback a video. Select the date on the calendar Then select the time you want to watch Check on below line if it is the period you need If data are available a will appear, then press PLAYBACK, If you press BACKUP then you have the specify the period then press START BACKUP you will have to specify the folder destination

When backup is finished, a confirmation message will display. Then press Live display to return to normal operation Record User can choose to record one specific channel or all channel. User can enable or disable record. Quality level: you can select between low, normal and high quality Enable or disable audio recording on all channel When SSD storage is damage or record fail, data will automatically be recorded on SD vehicled. (※ SD VEHICLED can support up to 32GB and need to format FAT32 before using.) (※ Does not support hot-swappable SD vehicled, do not remove the SD vehicled while in

Enable or disable overwriting on SSD Ignition off: After you switch off the power, the user can setup ignition off time Streaming setup

User can adjust camera brightness, contrast, saturation and Hue. Press apply to validate your choice

Dwell time: 0 to 9 seconds Email: disable or enable Alarm out: if user wants send alarm out when video loss, click on the 1 so it has a click Motion detection

To select a cell: Mouse Left Click, / To deselect a cell: Mouse Right Click, To select or deselect a block: Press Ctrl + Mouse Click Blue area means selected /No color area means not selected User can setup which camera to record in case of motion detection Dwell time: 0 to 9 seconds Email: disable or enable Alarm out: if user wants send alarm out when motion detection, click on the 1 so it has a click Popup: displays a selected camera when motion detection occurs Sensitivity: 1 to 5 Press apply to validate your choice Sensor Sensor: 1 to 8 Enable: setup the status of the sensor OFF / HIGH Record CH: select which camera to record in case of sensor trigger Dwell time: define the length of the buzzer after each sensor trigger 0 ~ 9 seconds Pop up priority Email: disable or enable Alarm out: in case of sensor trigger, DVR will send a signal via alarm out like a buzzer or flashing red light Popup: 1 ~ 4

Dwell time: define the length of the buzzer after each motion detection 0 ~ 9 seconds Email: can send an email to predefined address in case of the event Alarm out: in case of G-Sensor detects a variation, DVR will send a signal via alarm out like a buzzer or flashing red light Speed event This page let user to enable or disable the speed event detection Unit can be kilometer per hour KPH or mile per hour mph User can enable or disable high speed detection, specify the highest speed threshold, its dwell time from 0 to 9 seconds, whether to send an email or not and whether to enable alarm out.

Network This side enables user to setup network in order to remotely connect to it for example with a notebook for maintenance. If the network has a DHCP server, you can enable this function. Please make sure that gateway and subnet mask are the same on both side.

access to the DVR via browser or VMS software. All these port can be customized according to your needs Server software installation Server main purpose is to receive data from each mobile DVR, so user needs to tell to DVR the server IP, open internet explorer and key in the DVR IP, then go to Network then Port

Port: check with port your SMTP server is using SSL: enable or disable according to your SMTP server Sender: key in the email of the sender Recipient: key in the email of the person who will receive notification in case of event. SMTP authentication: enable or disable according to your smtp server if it’s enable user need to provide the mail account and password

Here you can enable or disable 3G. Provide information of how to connect to the 3G network (please check your operator for dial up procedure) WIFI setting Here you can enable or disable the wifi

- Network such IP, http port, streaming port, MAC address and gateway - Wireless network such as connection type, IP and gateway - SSD such brand size and occupation ration System Network: displays current network setting and Mac address SSD: displays SSD brand, model number, size and occupation percentage Display User can select which items to display

Guest can only see live picture Administrator as full authority on the device Cell phone and Email are just for reference and optional Date and time Select your prefered date format and hour format here Enable or disable daylight saving, according to the time zone, it will automatically turns it on and off at the right time Here you can manually setup your device time or synchronize with your computer time Vehicle information

Format User must format the SSD before start recording Factory reset Once press this option a warning message will appear asking you if you want to reset, press YES to apply Press ok

Select the starting and ending time, the channel concerned and use our 4 filters to reduce the number of event then press SEARCH. If you don’t select channel, it will display system event. If you want to backup the log, press BACKUP,

it will export all the events in one csv file Choose Save Then open the file with Microsoft Excel or any program supporting csv file

This guide is aim to install database and server application for mobile DVR。 Achitecture mobile dvr server and system architecture is based on three server Register Server, Log Server and Database server System architecture (F) Register Server (E) Device (A) VMS Private Network (B) DB Server (G) Log Server (D) 3G ISP Or Private Network

Although the server can be built on the same computer, to have the best performance, we recommend that each individual can have a separate server software hardware environment. Database server and application server farm proposal meet the following basic requirements to achieve the best performance. System hardware basic requirements Item Minimum requirements notice CPU 32/64bit，above four core， each one at least 1.5GHz Memory Above 4GB SSD storage At least 500GB Network Ethernet 100/1000M Need static IP from telecom provider or setup in the firewall Port Forwarding Minimum requirements of the software 8.2 Database Server setting (notice：if MS SQLServer is already installed please bypass this step 8.3 Before install SQL Server 2008 Express please make sure you installed below software Step 1：download and install Microsoft .Net Framework 3.5 SP1 Step 2：download and install Windows Installer 4.5 Step 3：download and install Windows PowerShell 1.0 Server type item Minimum requirements Database Server Operating System Windows XP above 32/64 bits .Net Framework 2.0 and above Database system SQL Server 2008 Express R2 or above Register Server Operating System Windows XP above 32/64 bits .Net Framework 2.0 and above Log Server Operating System Windows XP above 32/64 bits .Net Framework 2.0 and above

following link http://www.microsoft.com/en-us/download/details.aspx?id=30438 Click on download and select the file SQLEXPRWT_x86_ENU.exe then click on NEXT

8.5.1.1 Launch the application called SQLEXPRWT_x86_ENU 8.5.1.2 Accept the licence term and click on next

8.5.1.7 Click on next the installation is finished

In windows bar, click on start all program Microsoft SQL Server 2008 R2 Configuration tools  SQL Server configuration manager in TCP/IP option，mouse right click TCP/IP choose Enable Then right-click on "Properties" to enter the "TCP / IP Properties" settings, switch to the "IP Addresses" tab in the Properties list, go to the last one "TCP port" setting is 1433. Then restart the SQL Server, click the "SQL Server Services" and then select "SQL Server" to restart its services to ensure the changes take effect

This software is located on the software cd folder called Environment Launch ServerDBInstall.exe, this installer must enter Database administrator (sa) password and automatically creates the necessary databases and tables, and generate the database dedicated management accounts ddadmin, the default password is 1111, for the first time after installation, please Be sure to modify the password. The installer only for database installation, delete function does not provide a database, the database administrator shall be manually deleted, if the repeated execution of the program, the original database data will be cleared, please exercise caution. Launch Server database installation program Enter the required information If the system is not installed MS SQL Server can not continue with the installation, they already exist, the database server can be used, it is in the "SQL Server Instance" field appears optional server name. Please enter a database and the highest privilege management account and password. If you need to change the actual data storage paths can modify "Database File Path" held only recommended default options.

Our VMS is composed : A client called Voyager VMS A pc viewer called Voyager PLAYER, A server software please follow below instructions Install Register server software located in the cd Setup folder on the server pc and follow instructions Then install the Voyager VMS software on the client pc and follow instructions

Default account and password are admin / 1111 Then you will access to a page showing device connection status At this page you can see each device registered ID(RID),Vehicle ID, Version of the firmware, Update time, network information and Status Clear button enables clear the current list, the server will then updates automatically the mobile DVR that can be linked

Click on the third tab will let you access to the account management

the right side. This concerns login from cms client, Click on the fourth tab will let you access to the server setting Server setting: default port is 8788 , you need to double check on the mobile dvr that the port is the same otherwise the server wont be able to see the device Start / Stop the service: the default setting is set on enabled but you can manually stop the server

Fill in Login ID and password Specify the server IP, Specify the server streaming port

Full Screen Displays the video in full screen on your monitor, to return to normal mode press ESC button on your keyboard Video download Manager Download recorded data from the dvr remotely, you can choose the vehicle ID, the channel , the date and time and the backup length and do multiple backup We recommend to be in LAN or WIFI environment to download the data and avoid be in 3G mode to download as the risk of failure is very high

all the functions are the same of the mobile dvr itself , to be able to access to the setting, the dvr must be connected. VMS option Lets you setup the snapshot path folder, live record path folder, event log number, GPS displayed unit, and used map

4 type of display are available select the one according to your preference Vehicle list: the program will show connected device with additional information, you can create or delete group for better management and pull one device to a group

, a vehicle icon will appear, right click on the mouse to display the functions Add vehicle: choose the vehicle you want to add by selecting them Then confirm by pressing OK

※ The GPS function is only for satellite positioning. This figure shows G-Sensor information This section shows real time information such as event, vloss, relay out or motion detection

② G-Sensor information and current speed ③ Display video by date ④ Playback bar ⑤ Video display mode ⑥ Display video by date ⑦ Sensor trigger status There are two ways to open the files: Open AVI To open a file press the first icon and find the folder you store the avi file You will be able see the recorded files displayed by date To play a file just double click on the date then a specific time

You can export the video into avi file by pressing the third icon

Icon Description Open SSD containing the video Open a avi file in a folder Open SD card containing the video Convert a period from the SSD into AVI format Stop the playback Playback Pause Fast Rewind Fast Forward Step Backward Step Forward Playback previous file Playback next file Take snapshot of current video System setting

, a window will pop out You can save manually or auto save the picture You can adjust print setting by pressing SETUP button, another window will come out You can add in your picture print license number, plate number, date and time, and also description (by adding text) If you press PRINT button, the computer will send the picture to your connected printer.

If you select “disable load map failed message, Voyager player do not show this warning. In this section, you can manage your different account, by changing administrator password or add new account. You can also delete user.