Scosche MA1532B Installation Manual

2006-UP MAZDA MIATA / MX5 VEHICLES LIABILITY DISCLAIMER This instruction booklet is based on carefully documented data and research of automobile dash disassembly, wire harness/ codes and information pertaining to installation of this kit (MA1532B) in 2006-Up Mazda Miata / MX5 GM Vehicles. Scosche Industries, Inc. can not be held responsible for discrepancies/inconsistencies that may occur due to the automobile manufacturing changes or options, or damage that may occur in the automobile during the installation of components while using this booklet. INTRODUCTION / PRELIMINARY CAR STEREO CONNECTORS PROVIDE EASY CONNECTION OF YOUR CAR STEREO TO FACTORY WIRING HARNESS. This premium installation kit is for MA1532B 2006-Up Mazda Miata / MX5 vehicles. Included are all the parts you need to mount your car stereo/cassette or CD player into your vehicle's dash. Refer to the individual instruction in this manual to remove your vehicle's factory radio and assemble the kit. CAUTION: DISCONNECT YOUR VEHICLE'S NEGATIVE BATTERY TERMINAL BEFORE THE INSTALLATION TO HELP PREVENT ELECTRICAL DAMAGE. WE RECOMMEND THE USE OF A VOLT/OHM METER OVER A TEST LIGHT TO CHECK WIRING. A TEST LIGHT OR GROUNDED WIRE PROBE CAN CAUSE DAMAGE TO THE VEHICLE'S COMPUTER AND/OR DIAGNOSTIC SYSTEMS. AVOID ALL FACTORY AIRBAG WIRING - AIRBAGS CAN ACCIDENTALLY DEPLOY CAUSING SERIOUS INJURY OR DEATH. NOTES: • See your vehicle's instructions for any special tools your installation might require. • Read all instructions accompanying your car stereo/cassette player for proper wiring and mounting instructions. MA03B 2000-Up Select Mazda MA03B 5742R BRACKET 5742L BRACKET 6248 POCKET 6228 KIT PANEL 6247 DIN TRIM RING 5908 DOUBLE DIN ISO BRACKET 6246 DOUBLE DIN TRIM RING 5908 DOUBLE DIN ISO BRACKET 4

RADIO REMOVAL: 1. Remove plastic knee guard panel. 2. Extract bolts securing knee guard panel. 3. Extract 1 hidden Phillips Head Screw securing side of radio. 4. Unsnap lower side trim panel on each side of the radio by pulling back on them and unsnap them. 5. Extract 1 Phillips Head Screw securing factory radio on each side. 6. Using a Panel Removal Tool, unsnap the parameter of the radio. Lift away disconnect and remove. MOUNTING THE RADIO DIN MOUNT 1. Slide pocket into kit panel from front until it snaps into place. 2. Next, slide DIN sleeve into kit panel from front and bend tabs to hold into place. 3. Insert radio into sleeve until it snaps into place. DIN RADIO DIN MOUNT REAR SUPPORT STRAPS 6228 KIT PANEL 6248 POCKET RADIO MOUNTING SLEEVE 6247 DIN TRIM RING BEND TABS OUTWARD NOTE: REAR SUPPORT AVAILABLE SEPARATELY. REAR SUPPORTING THE RADIO ADDS TO THE INSTALLATION’S STRUCTURAL INTEGRITY. ISO MOUNT 1. Slide pocket into kit panel from front until it snaps into place. 2. Slide left and right brackets into their corresponding slots in kit panel. 3. Mount radio to brackets with radio supplied screws. 4. Snap trim ring into place. DOUBLE DIN MOUNT 1. Slide left and right double DIN brackets into their corresponding slots in kit panel. 2. Mount radio to brackets with radio supplied screws. 3. Snap trim ring into place. DOUBLE DIN ISO MOUNT ISO MOUNT 6247 DIN TRIM RING 6248 POCKET 6228 KIT PANEL 5742R BRACKET 5742L BRACKET DIN RADIO 6246 DOUBLE DIN TRIM RING 5908 DOUBLE DIN ISO BRACKET 5908 DOUBLE DIN ISO BRACKET 6288 KIT PANEL REAR SUPPORT STRAPS DOUBLE DIN RADIO 3 MOUNTING A/C CONTROLS 1. Retain factory A/C controls and factory screws to be mounted onto panel. 2. Align A/C control unit and insert into panel. (Use factory screws) 3. Using factory screws, attach A/C unit to panel. A/C CONTROL UNIT 6288 KIT PANEL FACTORY A/C CONTROL UNIT * * * * USE FACTORY SCREWS * Choose Scosche products if you’re looking for a quality sound.