Seiko 7d46A Technical Manual

Cal. 7D46A, 7D48A 【SPECIFICATIONS】 Item Cal. No. 7D46A, 7D48A Movement Movement size Outside diameter φ３２.０ mm Casing diameter φ３０．０ mm Height ６.１ mm 3 hands (Hour and minute hands: 5-second interval movement, Second hand: 1-second interval movement), 24-hour hand Time indication (Movement intervals) Calendar Year indication: Indication disk for year (7D48A), Year indication hand (7D46A) Month indication:：Month indicator Date indication: Big calendar Driving system Step motor: 2 pieces ・ Piezoelectric motor (for calendar) Additional mechanism ● Automatic generating system ● Energy depletion forewarning function ● Overcharge prevention function ● Electronic circuit reset switch ● Train wheel setting device ● Instant setting device for date calendar ● Automatic power save function ● Time relay function ● Perpetual calendar (Year • Month • Date) up to February 28, 2100 Loss/gain Monthly rate at normal temperature range: less than 15 seconds Regulation system Nil Measuring gate by quartz tester Use 10-second gate. Power generator Automatic generating system Power supply Electricity storage Unit (E.S. Unit) Titanium lithium ion rechargeable battery Operating voltage range 0.45 ｖ～2.5 ｖ Continuous operating time Operable time of time relay function: approximately 4 years if fully charged Jewels 16 jewels SEI KO WATCH CORPORATI ON SEI KO WATCH CORPORATI ON SEI KO WATCH CORPORATI ON SEI KO WATCH CORPORATI ON

Cal. 7D** is an Automatic Generating System analog quartz watch equipped with piezoelectric motor, featuring the perpetual calendar and automatic adjustment function. Although Cal.7D** features new functions, the experience of repairing the existing KINETIC series watches will be helpful. In repairing Cal. 7D**, you are requested to have the full knowledge of its functions and strictly observe the repairing and checking instructions provided in this guide so that the watch will be repaired correctly. FEATURES OF CAL. 7D46A, 7D48A Cal. 7D** features the power save function that automatically stops the hands from moving if the watch is left untouched for a certain period of time. Even if the watch is in this state, the perpetual calendar continues to count the date until the stored electrical energy is depleted. When you decide to use it again, swinging the watch several times will activate the time relay function, which starts the hands moving quickly to indicate the correct time and resume the normal operation. Cal. 7D** is an innovative KINETIC model; it conserves the stored electrical energy by stopping the hands while it is not in use, and, at the same time, it completely eliminates the cumbersome time setting procedure when it is used again. 1. POWER SAVE FUNCTION � While the watch is not in use, the hands stop automatically to minimize the electrical energy consumed. This is called “the power save function”. Though the hands stop, the built-in IC continues to compute the time, keeping the watch ready for the next use. If the watch is left untouched for approximately 24 hours, the power save function is automatically activated. 2. TIME RELAY FUNCTION � While the power saving function is working, the built-in IC continues to compute the time though the hands stop. As the watch detects a certain amount of electricity generated by swinging it, the hands are automatically adjusted to the time retained inside the watch, resuming the normal operation. This is called the “time relay function”. As it is activated, the hour and minute hands are adjusted first, then, followed by the second hand. � By only swinging the watch for 2 to 3 seconds, the time relay function will be activated. (Caution) � It may take approximately up to 64 seconds (32 seconds on average) to activate the time relay function. � The accuracy of the time computation by the built-in IC is equivalent to that of conventional quartz watches. Especially when the watch has been left untouched for a long time before the time relay function is activated, the time indicated by the hands may include a certain amount of time loss or gain within the range of the accuracy of the watch (± 15 seconds per month) that has accumulated during that time. 3. CONTINUOUS OPERATING TIME ● The continuous operating time varies depending on the stored electrical energy inside the watch. In the case that the fully charged watch enters the power save mode, 2

(Caution) ◆ If the stored electrical energy is completely depleted while the watch is in the power save mode, swinging the watch may not activate the time relay function. Instead, the second hand starts moving at two-second intervals. 4. PERPETUAL CALENDAR ● The perpetual calendar automatically adjusts the date up to February 28, 2100. Even if the watch is in the power save mode, the calendar continues to function as normal. (Caution) � The date changes between 23:30 and 0:30. � Normally it takes approximately 2 seconds for the watch to change the date. However it may take up to 2 minutes especially during the wintertime or when the stored electrical energy is being depleted. � Even though the watch is reactivated after the stored electrical energy has become extremely low, the calendar can be easily adjusted manually. � When the watch is in power save mode, and the date does not change correctly (or shows the wrong date), the electrical power stored in the rechargeable battery is being depleted. Before starting to wear the watch, recharge the watch until the second hand no longer moves at two-second intervals and then reset the time and calendar. 5. TIME AND CALENDAR SETTING ● It is recommended that you adjust the time and/or calendar during the time between 1:00 and 23:00. ● If you adjust the time and/or calendar around 0:00, the date may become incorrect, but this is not a malfunction. ● When the watch moves at two-second intervals, the date stops changing. ● When the watch no longer moves at two-second intervals after it is recharged, reset the calendar. ● When the date is set to a non-existing date, such as February 30, the calendar automatically correct the date. (When the date is set to February 30, the calendar automatically shows March 1). ● When the stored electrical energy is completely depleted, and the watch is stopped, recharge the watch until it no longer moves at 2-second intervals and reset the time and calendar.

� 0500 531 � Oscillating weight wheel � 1002 504 � Rechargeable battery � clamp screw � 0012 354 � Rechargeable � battery clamp � 4225 542 � Rechargeable � battery unit (MT920) � 3023 24X � Insulator for � rechargeable battery � 4216 541 Case back 1 2 3 4 5 6 7 Remarks on removing the winding stem To remove the winding stem when taking out the movement from the case or while disassembling the parts during repair work, be sure to pull out the crown to the first click, and then, remove the winding stem while pushing the setting lever. - 4 -

※ Year i ndi cat or hand f or cal . 7D46A

for intermediate wheel for month indicator � Train wheel bridge � for calendar screw � 0012 354 � Date dial � for units digit� (0878 A85) � Date dial � for ten's digit � (0878 A84) � Date dial holder � for trans wheel � for units digit � 0839 506 � Train wheel bridge � for calendar � 0125 508 � Jumper for year � 1024 503 � Jumper � for units digit � 1024 500 13 To be removed while assembling To be removed while assembling 1.Supporting pin for alignment 8 10 9 11 12 14 15 � Indication disk � for year � 1023 560 - 6 - ※ 2.This is the repairing tool. (7D48A-JP) Please look at the Watch Catalogue. ※ 2.This is the repairing tool. (7D48A-JP) Please look at the Watch Repairing Tool Catalogue. Repairing Tool (for Cal.7D48A)

1021 503 Detection on wheel for month 1002 510 Intermediate wheel for year indicator 0817 516 Detection on wheel for year 1002 511 Indicator on wheel for year 1021 504 (for cal.7D48A) Driving on wheel for year 0802 507 22 Indicator on wheel for 24h 1021 502 Intermediate wheel for month indicator 0817 515 23 Detection on wheel for 24h 1002 509 24 25 2nd intermediate wheel for calendar 0817 513 26 Control wheel 1002 507 27 Screw for piezoelectric motor cover 0022 230 28 Piezoelectric motor cover 0839 505 16 17 18 19 20 21 Supporting pin for alignment To be set for assembling - 7 - 1021 505 (for cal.7D46A) 7D46 7D48

� connecting spring � 1018 500 30� 1st intermediate wheel � for calendar � 0817 512 31� Piezoelectric rotor block � 4146 514 32� Insulator for � piezoelectric motor � 4216 540 33� Piezoelectric motor lead plate � 0105 502 � 34� Piezoelectric stator block � 4583 500 35� Jumper for month � 1024 504 36� Spring for intermediate � wheel for month indicator � 1024 503 37� Jumper for ten's digits � 1024 501 Positioning pin for spring for intermediate wheel for month indicator To be set for assembling - 8 -