Silca Delta 2000 FO Operating Manual

This manual has been drawn up by SILCA S.p.A. All rights reserved. No part of this publication may be reproduced or used in any form or by any means (photocopying, microfilm or other) without the written permission of SILCA S.p.A. Published in june 2002 Printed in Vittorio Veneto by SILCA S.p.A. via Podgora, 20 (Z.I.) 31029 VITTORIO VENETO (TV) - Italy

GENERAL INSTRUCTIONS ..................................................................................2 1 TRANSPORT ...................................................................................................3 1.1 Packing .................................................................................................3 1.2 Transport ..............................................................................................3 1.3 Unpacking .............................................................................................3 1.4 Machine handling ..................................................................................3 2 WORKING PARTS ..........................................................................................4 3 MACHINE DESCRIPTION ...............................................................................5 3.1 Technical data ......................................................................................6 3.2 Electrical circuit .....................................................................................7 4 ACCESSORIES PROVIDED ...........................................................................8 5 MACHINE INSTALLATION AND PREPARATION .........................................9 5.1 Checking for damage ............................................................................9 5.2 Environmental conditions ......................................................................9 5.3 Positioning ............................................................................................9 5.4 Description of work station ..................................................................10 5.5 Graphics .............................................................................................10 5.6 Separate parts ....................................................................................10 5.7 Connection to the mains .....................................................................10 6 REGULATION AND USE OF THE MACHINE ..............................................11 6.1 Checking and Setting ..........................................................................11 6.2 Axial gauging ......................................................................................11 6.3 Cutting operations ...............................................................................12 6.4 Key cutting ..........................................................................................12 6.5 Checking set codes (Ford - Jaguar) ...................................................13 6.6 Setting the coded device ....................................................................13 6.7 Coded key-cutting ...............................................................................13 7 MAINTENANCE .............................................................................................14 7.1 Cutting tool replacement .....................................................................14 7.2 Brush replacement ..............................................................................14 7.3 Tracer point replacement ....................................................................15 7.4 Replacing the fuses ............................................................................15 8 WASTE DISPOSAL .......................................................................................16 9 ASSISTANCE ................................................................................................17 9.1 How to request service .......................................................................17

DELTA 2000 FO Copyright Silca 1998 1 GUIDE TO THE MANUAL This manual has been produced to serve as a guide for users of the DELTA 2000 FO key-cutting machine. Read it carefully; it is essential if you wish to operate your machine safely and efficiently. CONSULTATION The contents of the manual are divided into sections relating to: - Transport and handling ......................................................................................... Ch. 1 - Description of machine and safety devices .......................................................... Ch. 2-3-4-5 - Proper use of the machine ................................................................................... Ch. 5-6 - Maintenance ......................................................................................................... Ch. 7 TECHNICAL TERMS Common technical terms are used in this manual. To assist those with little experience of key cutting, below is an illustration of the terms used for the different parts of keys. Fig. 1 1) Head 2) Stem 3) Tip 4) Cuts 2 1 3 4

Operating manual - English 2 Copyright Silca 1998 GENERAL INSTRUCTIONS The DELTA 2000 FO key-cutting machine has been designed according to the specifications of the Machine Directives. From the design stage risks for the operator have been eliminated in all areas: transport, regulation, cutting and maintenance. The use of protective goggles is compulsory during cutting operations, as indicated on the machine itself and in this manual. The material used in the manufacture of this machine and the components employed during use of the machine are not dangerous and their use complies with standards. USE The DELTA 2000 FO key-cutting machine must be installed and used in the way laid down by the manufacturer, as illustrated in this manual. If the machine is used differently or for purposes different from those described in this manual, the customer will forego any rights he may have over SILCA S.p.A. Furthermore, unforeseen danger to the operator or any third parties may arise from incorrect use of the machine. Negligence in the use of the machine or failure on the part of the operator to observe the instructions given in this manual are not covered by the guarantee and the manufacturer declines all responsibility in such cases. It is therefore indispensable to read the operating manual carefully in order to make the best use of the DELTA 2000 FO key-cutting machine and benefit from its potential. FURTHER RISKS There are no further risks arising from the use of the DELTA 2000 FO key-cutting machine. PROTECTION AND SAFETY PRECAUTIONS FOR THE OPERATOR The DELTA 2000 FO key-cutting machine is built entirely to standards. The operations for which it has been designed are easily carried out at no risk to the operator. The adoption of general safety precautions (use of protective goggles) and observation of the instructions provided by the manufacturer in this manual eliminate all human error, unless deliberate. The DELTA 2000 FO key-cutting machine is designed with features which make it completely safe in all its parts. • Power supply The key-cutting machine must be supplied with electricity by means of a safety device (supplied with the 230V machines; on request for other voltages). The plug must be earthed. • Start-up The machine is started up by means of: 1) the safety device switch (supplied with the 230V machines); 2) the ON switch, situated on the machine, which activates the machine motor. • Maintenance The operations to regulate, service, repair and clean the machine have been devised in the simplest and safest way possible. There is no danger of removable parts being replaced wrongly or unsafely. • Machine identification The DELTA 2000 FO is provided with an identification label which shows the serial number (fig.2). ATTENTION: should the machine be left on continuously for over 50 minutes, the cutting tool motor is protected against overheating and will automatically cut out. In such cases, proceed as follows: a) turn off the master switch (D) (fig.5, page 4); b) let the motor cool for at least 2 hours before using the machine again. Fig. 2 (*) seechap.8 WASTE DISPOSAL, page 16.

DELTA 2000 FO Copyright Silca 1998 3 1 TRANSPORT The DELTA 2000 FO key-cutting machine is easily transported and is not dangerous to handle. The packed machine can be carried by one person. 1.1 Packing The DELTA 2000 FO key-cutting machine comes in a strong cardboard box, the dimensions of which are shown in fig.5, designed to protect the machine and all its parts even when it is stored for long periods. Fig. 3 1.2 Transport It is advisable to use the packing every time the machine is transported, as this will avoid knocks which could cause damage to the machine, persons or things. 1.3 Unpacking To remove the machine from the packing box, carefully follow the illustrated instructions below: Fig. 4 Check the contents of the box, which should comprise: 1 DELTA 2000 FO key-cutting machine; 1set of documents including: operating manual, spare parts list and guarantee; 1chippings tray; 1 power cable; 1 power supply safety device (supplied with the 230V machines); 1 set of accessories. 1.4 Machine handling When the DELTA 2000 FO key-cutting machine has been unpacked, place it directly on its workbench. This operation can be carried out by one person, firmly holding the base, and no other part, to lift and carry the machine. A B C D

Operating manual - English 4 Copyright Silca 1998 2 WORKING PARTS Fig. 5 A - rotating centring clamp A1 - key-locking grub screw A2 - tip stop groove A3 - Ford/Jaguar selection cylinder A4 - coded angle device drum A5 - angle code viewing window B - carriage B1 - carriage lever handle C - chippings tray D - motor/brush start button E - axis regulation grub screw E1 - axis regulation locking screw E2 - coded spacing device knob F - tracer point F1 - tracer point locking screw F2 - adjusting nut F3 - tracer point’s group locking screw G - cutting tool H - carter I - motor J - brush K - supply socket L - fuses X - safety device (supplied with the 230V machines; on request for other voltages) X1 - safety device main switch X2 - warning light A1 H I D F L K J B1 C F2 F1 F3 G A A2 A4 A5 E2 E1 E CODED SPACING DEVICE CODED ANGLE DEVICE B A3 X X1 X2

DELTA 2000 FO Copyright Silca 1998 5 3 MACHINE DESCRIPTION DELTA 2000 FO is a professional key-cutting machine for FORD® and JAGUAR® car keys. The machine comprises the following main parts: SAFETY DEVICE The device is connected to a power plug with a differential switch. power the key-cutting machine by pressing the switch (X1) (fig. 6). The warning light (X2) illuminates to indicate voltage in the plug (X3). WARNING: Switch (X1) is electromagnetic, in the event of a power failure it goes out automatically. When electricity is restored it must be reset manually to power the machine again by means of the plug (X3). Fig. 6 MASTER SWITCH (D) The motor and brush starting button (D) is placed on the left side of the DELTA 2000 FO key-cutting machine. ATTENTION: the switch is constantly illuminated to indicate that the machine is live. MOTOR The DELTA 2000 FO has a direct drive motor. The transmission unit comprises the motor, cutter and brush and is protected by a single cover (H). MOBILE UNIT The mobile unit comprises a carriage (B) to which is fitted the coded spacing device and a key-locking clamp with a coded angle device. The carriage is fitted to the translation shaft and is moved manually by the operator. It has been designed to avoid the accumulation of cutting dust or chippings. The key-cutting machine has an inclined table which allows the chippings to collect in the special tray (C) placed under the carriage and easily removable for thorough cleaning. • Brush (J) The brush is used to eliminate burrs caused by the cutting process and is made of safe materials. • Cutting tool (G) The cutting tool is the part of the DELTA 2000 FO machine which cuts the key blank. The tool is in HSS super rapid steel and is protected by a special cover (H) to ensure safe operation. • Tracer point (F) The tracer point is housed on the left-hand side of the machine base. Its depth settings are easily regulated with the ring nut (F2). • Coded angle device The device comprises: - tip stop (A2) connected directly to the angle setting device; - idle bush (A) for centring and locking the key. • Key-locking grub screw (A1) The key is secured by means of a grub screw which ensures perfect grip on the key. • Coded spacing device The code device comprises a knob (E2) to activate a graduated slide which determines the position of the various cuts. X X1 X2 X3

Operating manual - English 6 Copyright Silca 1998 3.1 Technical data ELECTRICAL PROPERTIES: 230V - 50Hz 190W 1,5A 110V - 60Hz 250W 3,5A CUTTING TOOL: Super Rapid Steel (HSS) MOTOR: One speed single phase 230V-50Hz 1350 rpm 0,145 Kw 110V - 60Hz 1700 rpm 0,180 Kw SAFETY DEVICE: supplied with 230V key-cutting machines CLAMP: rocker CARRIAGE MOVEMENT: manual CARRIAGE RUN (maximum length of cuts): 23 mm DIMENSIONS: width: 210 mm depth: 370 mm height: 250 mm CUTTING NOISE: Lp (A)= 92,2 dB (A) NOISE POTENTIAL: Lw (A)= 104,9 dB (A) WEIGHT: Kg. 14

DELTA 2000 FO Copyright Silca 1998 7 3.2 Electrical circuit The DELTA 2000 FO key-cutting machine is provided with a motor which performs: - 1350 rpm with consumption of approx. 0,19 kw and absorption of 1,5A on 230V version; - 1700 rpm with consumption of approx 0,25Kw and absorption of 3,5A on 110V version. The main parts of the electrical circuit are listed below: 1) Safety device inlet 2) Safety main switch 3) Warning light 4) Wiring clip 5) Machine inlet 6) Rapid 3,15A fuses (230V); 6,3A (110V) 7) Switch with lamp 8) Motor: 230V a.c. 50Hz 9) 6,3 F condenser on 230V version; 20 F on 110V version 5 6 6 7 8 9 110V 230V machine inlet motor 3 brown light blue yellow-green brown light blue OUT IN 4 1 2 Safety device

Operating manual - English 8 Copyright Silca 1998 4 ACCESSORIES PROVIDED To ensure trouble-free working with the DELTA 2000 FO, it is advisable to always have certain spare parts on hand. It is advisable to always have a tool box containing: tools, cutting tools, brushes and small replacement parts. DELTA 2000 FO is supplied with a full range of accessories. The accessories provided by Silca are all that is necessary to carry out the operations for which the machine is designed. code D309226ZZ Fuses 5X20 3,15A rapid (230V) code D306748ZZ Fuses 5X20 6,3A rapid (110V) 1 2 3 4 5 6 8 9 code D300222ZZ 2,5 mm Allen key code D300223ZZ 3 mm Allen key code D300308ZZ 10 mm Spanner code D312327ZZ 15 mm Spanner code D300224ZZ 4 mm Allen key code D302883ZZ 8 mm Spanner 7 code D301760ZZ 17 mm Spanner code D413665LA gauging calliper

DELTA 2000 FO Copyright Silca 1998 9 5 MACHINE INSTALLATION AND PREPARATION The DELTA 2000 FO key-cutting machine can be installed by the purchaser and does not require any special skills. However, some checks and preparation for use need to be carried out by the operator. 5.1 Checking for damage The DELTA 2000 FO is solid and compact and will not normally damage if transport, unpacking and installation have all been carried out according to the instructions on the packing box. However, it is always advisable to check that the machine has not suffered any damage. 5.2 Environmental conditions To ensure that the best use is made of the key-cutting machine, certain parameters must be borne in mind: - damp, badly ventilated sites should be avoided. - the conditions for the machine are: temperature:between 0 and 40°C relative humidity:approx. 60% 5.3 Positioning Place the machine on a horizontal surface, solid enough to take the weight (14 Kg). To facilitate operation and maintenance, install the machine with a clearance of at least 200 mm on all sides (fig.7). Check that the weight of the machine is evenly distributed over the four feet; horizontal positioning prevents vibrations during operation. ATTENTION: ensure that the machine voltage is the same as that of the mains, which must be properly earthed and provided with a differential switch. Fig. 7 200 mm

Operating manual - English 10 Copyright Silca 1998 5.4 Description of work station The machine needs only one operator, who has the following controls at his/her disposal (fig.8): - safety device (X). - master switch (D), placed on the left-hand side of the machine; provided with a warning light indicating that the machine is live. - carriage lever handle (B1). Fig. 8 5.5 Graphics 5.6 Separate parts The detachable parts of the machine are packed separately and must be fitted to the DELTA 2000 FO by the operator, as follows: POWER CABLE 230V version: first connect the safety device (X) to the key-cutting machine and the power cable then connect the free end of the power cable to the power mains (fig.9). 110V version: connect the key-cutting machine and the power cable then connect the free end of the power cable to the power mains (fig.9). Fig. 9 5.7 Connection to the mains It is extremely important for the operator’s safety to ensure that the key-cutting machine is connected to the power mains with the right voltage and by means of a properly earthed differential switch. D B1 X THE USE OF PROTECTIVE GOGGLES IS COMPULSORY power cable power mains power cable power mains X

DELTA 2000 FO Copyright Silca 1998 11 6 REGULATION AND USE OF THE MACHINE 6.1 Checking and Setting The cutting tool on the DELTA 2000 FO is used to cut the key blanks and must be periodically checked and replaced. Periodically, and whenever the cutting tool is replaced, check the key-cutting machine settings, to ensure perfect machine efficiency. 6.2 Axial gauging Axial gauging is regulation of the position of the cutting spaces (fig.10). Fig. 10 Fig. 11 AXIAL GAUGING REGULATION To regulate the axial gauging, proceed as follows: ATTENTION: disconnect the machine from the mains. 1) set up the coded spacing device by means of the knob (E2) so that the indicator "F" is aligned with position "d" (fig.12). 2) insert the tip of the gauging calliper (provided) into the rotating clamp (A), push up against the tip stop (A2) and lock in the calliper by tightening the grub screw (A1) (fig.13). The calliper must be positioned horizontally as shown in the illustration; if adjustment is necessary use the hex wrench provided to turn the screw (P) (fig.17, page 13) so that the drum (A4) turns clockwise. 3) take the carriage towards the cutting tool and place the tracer point (F) all the way into the locating groove (E3) (fig.12). 4) check that the cutting tool enters clearly into the groove (A3) in the gauging calliper. If adjustment is necessary, loosen screw (E1) and adjust axial gauging by means of the grub screw (E). 5) when gauging is complete, tighten the screw (E1) well. DEPTH SETTING Depth setting is regulation of the cutting depth (fig.11). Usually depth setting is not necessary during normal use of the machine. However, if the tracer point is replaced or an optional carriage is used it is advisable to check the depth settings. Fig. 12 Fig. 13 E N O E1 E3 E2 d F A A2 gauging calliper A1 A3 A4

Operating manual - English 12 Copyright Silca 1998 REGULATING DEPTH SETTING To regulate the depth settings, proceed as follows: ATTENTION: disconnect the machine from the mains. 1) set up the coded spacing device by means of the knob (E2) so that the indicator "F" is aligned with position "d" (fig.12). 2) insert the tip of the gauging calliper (provided) into the rotating clamp (A), push up against the tip stop (A2) and lock in the calliper by tightening the grub screw (A1) (fig.13). The calliper must be positioned horizontally as shown in the illustration; if adjustment is necessary use the hex wrench provided to turn the screw (P) (fig.17, page 13) so that the drum (A4) turns clockwise. 3) take the carriage towards the cutting tool and place the tracer point (F) all the way into the locating groove (E3) (fig.12, page 11). 4) check that the cutting tool enters clearly into the groove (A3) in the gauging calliper. If adjustment is necessary, adjust axial gauging in the way described above ("Axial gauging regulation"). 5) loosen the screw (F3) locking the tracer point unit (fig.5, page 4). 6) use the lateral brush (J) to turn the cutting tool shaft in the opposite direction to cutting. The cutting tool should skim the bottom of the groove (A3) on the gauging calliper. If not, turn the ring nut (F2) (fig.5, page 4) clockwise to move the cutting tool unit forward, or in the opposite direction to move it back. 7) when the ideal regulation has been reached, tighten the tracer point locking screw (F3) (fig.5, page 4). If an optional carriage is used, check that the tracer point enters freely into the locating groove (E3) (fig.12, page 11) and that there is not excessive play on it. If necessary, adjust play between the locating groove and tracer point by loosening the nut (O) and turning the grub screw (N). When adjustment is complete, tighten the nut (O). 6.3 Cutting operations ATTENTION: to work in complete safety, pay special attention to the following recommendations: • Always work with dry hands. • Check that the machine is properly earthed. • Use the protective goggles, even if the cutting tool is fitted with a protective shield. • Start the motor only when all the operations with the carriage have been carried out (securing keys, etc.). • Keep hands away from the cutting tool when in motion. 6.4 Key cutting PLACING KEYS INTO CLAMP 1) place the key blank into the rotating centering clamp (A) (fig.14). 2) push the key tip up against the tip stop groove (A2). Hold down the key and lock into the rotating clamp with the grub screw (A1). ATTENTION: when cutting original FORD keys with lights, before locking into the clamp detach the part containing the electrical devices, otherwise the head is too big (fig.15). Fig. 14 Fig. 15 A A2 blank-key A1 A1 A4 blank-key F A5

DELTA 2000 FO Copyright Silca 1998 13 6.5 Checking set codes (Ford - Jaguar) The machine can cut both Ford and Jaguar keys following a simple operation to carry out on the coded angle device. To check the current setting, proceed as follows: 1) place the key blank tip into the rotating clamp (A) and push up against the tip stop groove (A2). 2) continue to push, and check that the key is in the vertical position (fig.15) and the number "1" is visible in the window. If necessary, turn the key until it is properly positioned. 3) check the reading on the drum (A4). If the letter "F" is visible the device is set for cutting Ford keys, if the letter "J" is visible the device is set for cutting Jaguar keys.The machine leaves our workshops set for cutting Ford keys. 6.6 Setting the coded device The change the coded device setting from FORD to JAGUAR and vice versa, proceed as follows: 1) place the key blank tip into the rotating clamp (A) and push up against the tip stop groove (A2) (fig.14, page 12). 2) hold the key head firmly and use the left hand to loosen the screw (P) (fig.17) with the wrench provided. 3) exert slight pressure in the direction of the arrow (fig.17) and unscrew the screw (P) slowly so that the cylinder (A3) protrudes a few millimetres (fig.16). 4) use the key head to turn the cylinder 90° in the direction of the arrow. 5) let the cylinder (A3) withdraw and press on the key head to tighten screw (P). The cylinder must return freely into its seat. If necessary, seek its proper position by turning the key slightly in the two directions. 6) turn the key 90° to pull the coded angle device. The letter visible on the drum (A4) will now be different, as will the colour of the numbers in the window (A5). 6.7 Coded key-cutting To cut a key blank by code, see the instructions below: 1) check that the coded device has been properly set for the type of key to be cut (see points 6.5 and 6.6). 2) place the key blank into the rotating clamp (A) and push against the tip stop groove (A2) (fig.14, page 12). Hold the key down in the rotating clamp (A) and tighten the grub screw (A1) with the wrench provided. 3) set the cutting position on the coded spacing device by means of knob (E2) (fig.16). Exert pressure on the head to turn the key and turn the angle counter (Q) (fig.17) until the required code is visible in the window (A5). 4) start the machine with the motor/brush start switch (D). 5) take the carriage towards the cutting tool, ensuring that the tracer point enters the locating groove all the way (fig.16). When the cut has been made, move the carriage back and turn the key until the same code appears in the window (A5), after the number "1" has appeared. Repeat the cutting operation. 6) when the cut has been made, move the carriage back and give the key a half turn until the same code appears in the window (A5). Repeat the operation described in point 5. 7) the key has now been cut on both sides for the first cutting position. Go on to the following position and repeat the cutting operations with the relevant code, and so on until all the cuts have been made. 8) pull back the carriage, turn off the machine, loosen the grub screw (A1) and remove the key. Fig. 16 Fig. 17 A4 A5 A1 E2 Q locating groove A3 P A5 Q

Operating manual - English 14 Copyright Silca 1998 7 MAINTENANCE ATTENTION: for repairs or replacement of parts for maintenance, the ‘CE’ mark is guaranteed only if original spare parts provided by the manufacturer are used. Although the DELTA 2000 FO key-cutting machine does not require special maintenance, it is advisable to check and, if necessary, replace the parts subject to wear (cutting tool, brush, tracer point). Replacement is simple and can be carried out by the operator. CLEANING: it is advisable to use a soft brush to keep the carriage and clamps free of chippings from cutting operations. ATTENTION: DO NOT USE COMPRESSED AIR! ATTENTION: to keep the machine well maintained we recommend using protective oil, e.g. WD40 or similar, applied to the burnished mechanical parts. This prevents oxidation of the parts in question (clamps, guides, carriages, etc.). Before starting any type of maintenance (checks or replacements), read the instructions below: • never carry out maintenance or servicing with the machine switched on. • always remove the mains plug. • follow all the instructions in the manual to the letter. • use original spare parts. • always check that any screws or nuts removed when replacing a piece are properly tightened. 7.1 Cutting tool replacement It is not necessary to remove the protective shield in order to replace the cutting tool (G). ATTENTION: unplug the machine from the mains. 1) place the spanner provided in position on the motor shaft (fig.18); 2) use a suitable spanner to loosen the new cutting tool locking nut. ATTENTION: the thread is left-handed. 3) replace the cutting tool after cleaning its seat; 4) install the new cutting tool and tighten the nut. ATTENTION: the tool rotates clockwise. Fig. 18 7.2 Brush replacement When the brush (J) is no longer effective it must be replaced, as follows: ATTENTION: unplug the machine from the mains. 1) place the spanner provided in position on the motor shaft (fig.18); 2) use the wrench provided to loosen the brush locking screw (X) (fig.19); 3) replace the brush and secure with the screw; 4) remove the spanner from the motor shaft. Fig. 19 G X

DELTA 2000 FO Copyright Silca 1998 15 7.3 Tracer point replacement To replace the tracer point (F), proceed as follows (fig.20): ATTENTION: unplug the machine from the mains. 1) loosen and remove the tracer point locking screw (F1). 2) remove the tracer point. 3) fit the new tracer point. 4) re-gauge the machine as described in chapter 6 on page 11. Fig. 20 7.4 Replacing the fuses ATTENTION: unplug the machine from the mains. 1) detach the wiring from the machine plug; 2) turn the key-cutting machine so that the fuse box is easily reached; 3) remove the fuse box placed below the power inlet (K) (fig.21); 4) replace the fuses (L); 5) close the fuse box and connect the power cable. ATTENTION: the fuses must both be of the same type (rapid) and with the same amps (3,15 Ampere on 230V, 6,3 Ampere on 110V). Fig. 21 F F1 L K

Operating manual - English 16 Copyright Silca 1998 8 WASTE DISPOSAL EU regulations establish special arrangements for the disposal of waste (**). • Waste deriving from cutting operations Although residue coming from the key-cutting operations is classified as special waste, it is included in solid urban waste (SUW) as metal wool. Such waste is sorted according to its classification under current Italian and EU law and consigned to the proper disposal units. Cases where waste can be considered contaminated or containing toxic/harmful substance sufficient to transform it from SUW to toxic/harmful waste, are listed in the enclosures to current Italian and EU waste disposal regulations. Re-cycling is a recommended ecological practice. • Packing The DELTA 2000 FO is consigned in a cardboard packing box which can be re-used if undamaged. When it is to be thrown away it is classified as solid urban waste and should be placed in the special paper collecting bins. INFORMATION FOR USERS as per art. 10 of Directive 2002/96/CE of 27/01/2003 regarding waste from electric and electronic appliances (RAEE), • The symbol illustrated above, also found on the machine, indicates that it has been placed on the market and must be included in separate rubbish collection when the user wishes to dispose of it (including all components, sub-assemblies and consumables that are integrated in the product). • For information about the collection system for such appliances please contact SILCA S.p.A. or another subject registered in the various National Rolls for other countries in the European Union. Household waste (or of similar origin) can be included in the separate collection system for urban waste. • On purchasing a new appliance of equivalent type, the old one can be consigned to the dealer. The dealer will then contact whoever is responsible for collecting the appliance. • Suitable separate collection of the unused appliance and its dispatch for treatment, recovery and environmentally compatible disposal, makes it possible to avoid potential negative effects on the environment and human health, and aids recycling and the recovery of the materials used. • Unauthorised disposal of the product by users involves the application of the sanctions provided for in received Directives 91/156/CE and 91/689/CE. (**) "Waste" is any substance or object deriving from human activity or natural cycles, thrown away or to be thrown away.

DELTA 2000 FO Copyright Silca 1998 17 9 ASSISTANCE Silca provides full assistance to purchasers of the DELTA 2000 FO key-cutting machine. To ensure complete safety for the operator, any job not specified in this manual should be carried out by the manufacturer or in the special Service Centres recommended by Silca. On the back cover of this manual is a list of the manufacturer’s addresses; listed below are the addresses of specialised Service Centres. 9.1 How to request service The guarantee attached to DELTA 2000 FO key-cutting machine ensures free repairs or replacements of faulty parts within 12 months of purchase. All other service calls must be arranged by the customer with Silca or with a Silca Service Centre.

CE DECLARATION OF MACHINE COMPLIANCE SILCA S.p.A. - VIA PODGORA 20 ( Z.I.) 31029 VITTORIO VENETO (TV) - (ITALY) TEL. 0438 9136 - FAX. 0438 913800 Declares under its own responsibility that the Key-cutting machine model DELTA FO complies with the requirements of the following European Directives: European Union DIRECTIVE 2006/42/CE (Machines) and with the EN 292/1 – EN 292/2 Standards European Union DIRECTIVE 2004/108/CE (Electromagnetic Compatibility) and with the EN 55022 - IEC 801-2 - IEC 801-4 Standards European Union DIRECTIVE 2006/95/CE (Low Voltage) | 97 | and with the EN 60204-1 - EN 60950 Standards Claudio Tomasella of the Silca S.p.A. Research & Development Division is authorized to create a Technical File. General Manager Basic Production Center

CENTROS DE ASISTENCIA - CENTROS DE ASSISTÊNCIA - BIJSTANDSCENTRA COUNTRY COMPANY ADDRESS CITY AREA CODE PHONE FAX e-mail Algeria Sarl Maghreb Clés Coopérative Ettadhamoune Local 21/A Badjarah / Alger 16209 +213-21-264934 +213-21-264888 [email protected] Argentina Distribuidora Frappampino S.r.l. La Rioja, 483 Cordoba 5000 +54-351-4216368 +54-351-4229003 [email protected] Australia Locksmiths' Supply Co. Pty Ltd. 140/158 Dryburgh St. North Melbourne VIC 3051 +61-39-3297222 +61-39-3281731 [email protected] Austria Erwe Gmbh Feldgasse, 16 Feldkirchen A-9560 +43-42762816 +43-42765054 [email protected] Belgium Duitman Bvba Zinkstraat 13 Halle 1500 +32-2-3831620 +32-2-3831622 [email protected] Brazil Kaba Do Brasil Ltda. Rua Guilherme Asbahr Neto 510 São Paulo 04646- 001 +55-11-5545-4510 +55-11-5545-4515 [email protected] Bulgaria Intesa S.r.l. 1, Kukush Sofia 01309 +359-2-8211425 +359-2-8211347 [email protected] Burkina Faso Diallo Mamoudou Av.Houari Boumedienne Porte N. 1651 01BP / 2957 Ouagadougou 01 +226-710448 +226-710002 [email protected] China Silca China Xinhua Industrial Zone Guanghai County, Taishan, Canton +86-750-5325698 +86-750-5315655 [email protected] Colombia Flexon Llaves S.A. Av.Carrera 70 No.99 - 55 Entrada 1 Bogotà +571-2538300 +571-5331842 Croatia Ferrotechna d.o.o. Japodska, 66c Pula 52100 +385-52-503-529 +385-52-502-609 +385-52-503-529 [email protected] Cyprus G.H. Yacoubian Ltd. 74/B, Regaena Street Nicosia +357-22-663525 +357-22-669009 [email protected] Czech Republic H&B Plus. s.r.o. Zatecká, 8 Plzen 30148 +420-377-225903 +420-377-225904 [email protected] Denmark Agenturcentret A.S Brydehusvej 20 Ballerup 2750 +45-70111211 +45-70111221 [email protected] Egypt Gam Transworld 23 Omer Ibn El-Khatar Street Heliopolis El Cairo +20-2-22404705 +20-2-26441401 +20-2-22404705 [email protected] Finland Hardware Group Finland Oy. (Hgf Ltd) Luostarinportti 5 Kirkkonummi 02400 +358-9-2219490 +358-9-2962186 [email protected] France SILCA S.A.S. 12, Rue de Rouen B.P.37 Z.I. Limay Porcheville 78440 +33-1-30983500 +33-1-30983501 [email protected] Germany SILCA GmbH Siemensstrasse, 33 Velbert 42551 +49-2051-2710 +49-2051-271172 [email protected] Greece Chrisikos K. Ioannhs 7 Pipsou St. Thessalonik TK 54627 +30-2310-510336 +30-2310-521651 [email protected] Greece F. Sotiropoulos & Son O.E. Patission Str., 110 Athens 11257 +30-210-8234009 +30-210-8238480 [email protected] Greece GEMKA-Karidis G. & Sons OE Lykoyrgoy St. 14-16 Athens 10552 +30-210-3243000 +30-210-3249571 [email protected] Greece Fr.lli Raptakis Pili Iisou 10 Iraklion - Crete +30-2810-285000 +30-2810-280165 [email protected] Guinea Soguintec S.A. Calle Abilio Baloboa Malabo - Provincia del Bioko Norte +240-556618 Holland Duitman B.V. Aquamarijnstraat 5 7554 NM - Hengelo +31-74-2452520 +31-74-2452522 [email protected] Holland H. Cillekens & Zn. B.V. Metaalweg, 4 JB Roermond 6045 +31-475-325147 +31-475-325148 [email protected] Holland Steenhauer B.V. Oude Raadhuisstraat 1 Ap Leidschendam 2266 +31-70-3177262 +31-70-3177333 [email protected] Hong Kong Professional Lock Centre Co. Ltd. Unit A-D, 9/F. Gemstar Tower, 23 Man Lock Street Hunghom, Kowloon, Hong Kong +852-23302268 +852-23302082 [email protected] Hungary Kaba Elzett Megyeri út 51 Budapest 1044 +36-1-3501011 +36-1-3290692 [email protected] India Minda Silca Engineering Ltd. Plot No. 37, Toy City Greater Noida 201308 +91-987-397630 +91-987-397631 +91-120-2351301 [email protected] Iran Klidavarshayan Co. No.73 Stakhr. St - Emam Khomaini Ave. Tehran +98-216-6702757 +98-216-735649 [email protected] Israel A.M.C.I. Locksmith Supply Ltd. 22 Efal Street Kiryat Aryeh P.O.Box 3667 Petah Tikva 49130 +972-3-9230331 +972-3-9230332 [email protected] Italy SILCA S.p.A. Via Podgora, 20 (Z.I.) Vittorio Veneto - TV 31029 +39-0438-9136 +39-0438-913800 [email protected] Japan Clover Co. Ltd 1-2-40 Haradanaka, Toyonaka-shi Osaka 561- 0807 +81-6-6844-2111 +81-6-6844-1147 [email protected]

Nairobi +254-20-6532913 +254-20-6533370 +254-20-6533369 [email protected] Kuwait Hasawi & Sabano Co. For Gen.Trad. P.O. Box 42105 Kuwait City 70652 +965-24832505 +965-2622778 [email protected] Latvia Solo F Ltd. Salaspils 12 Riga 1057 +371-7278359 +371-7876901 [email protected] Lebanon Mouawad Books & Stationary Sarl. Mouawad Str. Mouawad Center, 60094 Jal el Dib Beyrouth +961-4-711202 +961-4-11206 [email protected] Macedonia Panevski & Sinovi Llidenska , 11 Kumanovo 1300 +389-31-411545 +389-31-412411 [email protected] Malta Unimark Ltd. 32, Zerafa Str. Hmr 03 Marsa +356-21-231540 +356-241319 [email protected] Mexico Corporacion Cerrajera Alba Sa De Cv Circuito Gustavo BAZ, 16 Atizapan de Zaragoza Messico D.F. 52966 +52-55-53667200 +52-55-53667291 [email protected] Mozambique Davel Importacao Comercio e Servicos Rua Do Carmo NR.54 - 3° Solat Coimbra 3000 +351 239833858 +351 914506747 New Zealand Baber LSC Limited Unit 5, 6 Argus Place Auckland Glenfield 1310 +649-444-5117 +649-444-5119 [email protected] Nigeria Chilex Security Products Ltd. 12, Olowu Street P.O. Box 5153 Ikeja - Lagos +234-1-4965005 +234-1-4965005 [email protected] Norway Prodib Ab Montorgat 16 Eskilstuna 632 29 +46-16-168000 +46-16-145590 [email protected] Poland Dar-Mar ul. Napoleona, 17 Kobylka 05-230 +48-22-7710118 +48-22-7710118 [email protected] Poland Z.P.U.H. Expres Wojcieck Kowalczyk 32-447 Siepraw 795 Siepraw +48-1227-46365 +48-1227-46365 [email protected] Portugal Casa Das Chaves Da Falagueira Ltda Estrada Da Falagueira 5B Amadora 2701 +351-214936430 +351-214912403 [email protected] Portugal Luso Chav' Av. Rodrigues de Freitas, 199-A Porto 4000- 303 +351-22-5104702 +351-22-5361248 [email protected] Romania M&C Business S.r.l. 36, Badea Cartan Street 2nd District Bucharest 20064 +40-213118602 +40-212120155 [email protected] Russia Strazh 16/2, pt. Komsomolskiy Moscow 119021 +7 495 7083440 +7-495-7083292 Russia O.O.O. Peter Key Mihaylovsky Pereulok, 7b Saint Petersburg 198095 +7-812-2520241 +7-812-2523885 [email protected] Saudi Arabia Fahd Omar Bamashmous Est. P.O. Box 20919 Jeddah 21465 +966-2-6422588 +966-2-6447238 [email protected] Serbia Silkon D.O.O. 29, Novembra 70 Belgrade 11000 +381-11-2080200 +381-11-3290017 [email protected] Singapore Silca Soxxi Pte. Ltd. 21 Toh Guan Rd. East #01-12 Toh Guan Centre Singapore 608609 +65-6316-8100 +65-6316-4470 [email protected] Slovakia H&B Slovakia s.r.o. Ovsistske Nam. 1 Bratislava 85104 +421-2-6252-0032 +421-2-6252-0033 +421-2-6252-0034 [email protected] South Africa Sanlic International (Pty) Ltd. 46, Hulbert Street New Centre Johannesburg +27-11-4939717 +27-11-6831312 [email protected] Spain Silca Key Systems S.A. C/Santander 73/A Barcelona 08020 +34-93-4981400 +34-93-2788004 [email protected] Sweden Prodib Ab Montorgat 16 Eskilstuna 632 29 +46-16-168000 +46-16-145590 [email protected] Switzerland Robert Rieffel Ag Widenholzstrasse 8 Wallisellen 8304 +41-44-8773333 +41-44-8773322 [email protected] Syria Muheiddin Arabi Katbi P.O. Box 1322 Damascus +963-11-2212407 +963-11-2224588 +963-11-2224588 +963-11-3737001 Taiwan Global Tecspro Ltd. 11F-2 N.42-2 Lian Sheng St. Jhongho City Taipei +886-2-22494028 +886-2-22425735 [email protected] Turkey Kadiköy Anahtar San.Ve.Tic.Ltd.Sti. Osmanaja Mah.Nüzhet Efendi Sk.No.56 Kadiköy - Istanbul +90-216-4145254 +90-216-3475488 [email protected] U.A.E. Sabano Trading Co.Llc P.O. Box 32075 Dubai +971-4-2682400 +971-4-2622778 [email protected] Ukraine Service-Centre Kopir Segedskaya 12 Odessa 65009 +38-487-433196 +38-487-190777 [email protected] United Kingdom SILCA Ltd. 6 Lloyds Court Manor Royal Crawley RH10 9QU +44-1293-531134 +44-1293-531108 [email protected] U.S.A. Kaba Ilco Corp. 400 Jeffreys Road, P.O. Box 2627 Rocky Mount NC 27804 +1-252-446-3321 +1-252-446-4702 [email protected] Venezuela La Casa del Cerrajero C.A. Av. Principal de Maripérez Caracas +58-212-793-0083 +58-212-781-8692 [email protected] Yemen Sabano Trading Co.Llc P.O. Box 32075 Dubai U.A.E. +971-4-2682400 +971-4-2622778 [email protected]

31029 VITTORIO VENETO (TV) Tel. 0438 9136 Fax 0438 913800 E-mail: [email protected] www.silca.biz Members of the Kaba Group