Yale Keyfree Connected Smart Lock Installation Manual

Please read the instructions before fitting and using the Keyfree Connected lock. Due to a continuous programme of development the company reserves the right to make alterations without notice. Version No. 1A

2. Multipoint Locking Compatibility 3. Fixing the Cylinder 4. Fitting The Spindle 5. Fitting The Handing Screw 6. Installation 7. Check Points after Installation 8. Electronically Handing the Lock 9. Troubleshooting 10. Quick Reference 1 2 3 5 6 1 1. Inside the Box Fit the Yale Keyfree Connected Smart Lock using a cross head screw driver to avoid cross threading the fixing screws. If using a cordless screwdriver, please ensure it is set to low speed & torque. M6: Thick & Short Screw×2 M4: Small Screw M4: Smallest Screw M6: Thick & Medium Screw×1 M5: Thin & Longest Screw×2 May be pre-assembled on main unit. 1 View Installation Video on YouTube

Fitting the Handing Screw Left Handed Door Right Handed Door Before fitting Keyfree Connected, the handing screw must be fitted. Failure to so will allow the outside lever to rotate 360º. Only use the handing screw provided which is attached to the underside of the outside lever in a bag with a yellow warning label. Lightly tighten the cylinder fixing screw. Cylinder fixing screw Fitting the Spindle 2 Insert the spindle into the main unit. After fully inserting the spindle, push the snap fit washer down until ‘click’ sound is heard. Check that the spindle freely rotates. If the main unit includes the spindle already, please skip this step. The keyfree handle set is only compatible with the following multipoint locks: • Yale YS170 Range • Yale Lockmaster Range • Yale DoormasterTM Range If you do not have any of the above multipoint locks the Yale Doormaster TM Range is designed to replace most PVCu door locks. For more information please go to www.yale.co.uk Multipoint Locking Compatibility 2 2. 3. 4. 5.

the door until a PIN code or a fob has been successfully registered and tested to be working. 3 3 6.

on the side. M6: Thick & Short Screw M6: Thick & Short Screw M4: Small Screw M6: Thick & Medium Screw M5: Thin & Longest Screw M5: Thin & Longest Screw Rubber Cap *IMPORTANT* 4 Take care not to damage spring when fitting inside handle 4

• Insert Remote Module (Optional) • Insert Batteries Take care inserting the Remote module (optional). The pins can easily bend and may not be replaced under warranty Electronically Handing the Lock • Check The Mechanical Back Up Key Works Properly - Turn key 90 degrees. - Press outside lever down & open door. - Remove key - Check the operation of the inside safety / security button handle. The inside lever must not move unless the button is depressed. When the inside lever returns to horizontal, the button must re-engage to prevent use. • Check the free movement of both inside & outside levers If the button does not re-engage, please slightly lift up the inside lever to re-engage. 5 8. Please follow the procedure below to set the handing of the lock. Failure to do this can leave the lock reporting it is locked when it is open and that it is unlocked when it is locked. Step Icon Expected Feedback Description Press any button Press any button on keypad to begin Enter master code followed by # key 2 tone beep If the master code has not been setup the default PIN is 123456 Open the internal cover and press the [P] button The [P] button is above the batteries on the back body On the front body keypad press the [#] key This will put the lock into handing mode Push the internal handle down Lift the internal handle up Press the [I] button, then replace the internal cover This will complete the lock handing. - If you have experienced any problems while installing the Yale Keyfree Connected Smart Lock, or it is not behaving as expected, please go to the following address on the Yale website or call the Keyfree helpline: - www.yale.co.uk/smart-living Tel: 01902 364606 Monday - Friday 8.30am - 5.30pm Email: [email protected] 9. Troubleshooting 7 5 7. 8. 9.

6 Change Your Master Code Connecting to a Home Automation System Please see page 8 in the user manual. Registering Your Remote Fobs (Optional) Opening and Locking Your Door Please see page 14 in the user manual. Please see page 19 in the user manual. Please see page 11 in the user manual. - - - - 6