D-Link DWL-P200 Quick Installation Manual

Adapters 48V DC Power Adapter ©2004 D-Link Systems, Inc. All rights reserved. Trademarks or registered trademarks are the property of their respective holders. Software and specifications subject to change without notice. About Power Over Ethernet. Check Your Package Contents DWL-P200 Base Unit and Terminal Unit Female-to-Female Power Connector Ethernet (CAT5 UTP/Straight Through) Cable Using a power supply with a different voltage rating will damage and void the warranty of this product. If any of the above items are missing, please contact your reseller. The DWL-P200 Power Over Ethernet (POE) Adapters are designed to supply operational power to a Network Device. These adapters eliminate the need to use an additional AC/DC power supply at the Network Device giving you the ability to mount an Network Device virtually anywhere in a building where power outlets are not available, ( for example in, ceilings, attics). D-Link’s DWL-P200 Adapters take advantage of the unused cable pairs within Ethernet Cat 5 cabling. The Base Unit inserts DC voltage into the unused wires therefore allowing the single Category 5 cable to carry both Ethernet data and DC power to an Network Device. The POE Terminal Unit splits the data and DC power apart, which is then supplied to the Network Device. Warning: Please follow the instructions in this guide carefully. Connecting these adapters incorrectly may result in damage to you network devices.

Base Unit Terminal Unit P+DATA OUT: provides the data and power to the terminal unit. Connect this port to the P+DATA IN on the Terminal unit. LAN IN: connect an RJ-45 straight-through cable to your computer or switch. Power In: using the supplied 48V power supply, connect to a wall power outlet. P+DATA IN: connect a CAT 5 RJ-45 straight-through cable from the P + Data Out port on the Base Unit. LAN OUT: connect a CAT 5 RJ-45 straight- through cable to an Ethernet enabled device. Voltage Selector: used to select DC 5V/ 2.5A or 12V/1A DC Out: supplies 5V 2.5 or 12V 1 amps of power. Using the included power cable, connect to your Ethernet enabled device’s power.

Insert one end of a Cat 5 Ethernet RJ-45 cable into the “LAN IN” port of the Base Unit. Connect the other end of the cable to your network switch or PC. DO NOT use two Base units together, or two Terminal units together. In configuring your network, pair one Base unit with one Terminal unit. Plug one end of the Power Adapter into the “DC 48V IN” Base Unit and the other end into your electrical outlet. The green “PWR” LED on the Base Unit should light up. Do Not mistake the “LAN IN” port with the “P + DATA OUT” port. Incorrectly plugging the wrong Ethernet cable into the wrong Ethernet port may cause serious damage to your network devices. D-Link will not replace or repair products or reimburse customers for devices that become damaged due to incorrect installation, nor is liable for any loss of business resulting in the incorrect installation of this product.

OUT” to the “P+DATA IN” of the Terminal Unit. Connecting The DWL-P200 Insert one end of the DC Power Cable that is provided into the Terminal Unit, and the other end into the DC of the Network Device. The Power LED of the Terminal Unit should light up. Only use a CAT 5 Ethernet straight-through cable. Use Voltage Selector to set DC output to 5V/2.5A or 12V/1A for the Network Device.

At this point, your Network Device should have power and data, and function normally. Connect the provided Cat 5 Ethernet cable from the Terminal Unit “LAN OUT” to the RJ-45 LAN port of the Network Device.

. Data: 1, 2, 3, 6 . Power: 4, 5, 7, 8 Voltage . Input: 48VDC, 400mA . Output: 5VDC, 2.5A or 12VDC, 1A Ethernet . Connector: RJ-45 . Data Rate: 10/100Mbps . Cable: TIA/EIA - 568, Category 5 Dimensions . Base Unit: 8.09 x 5.2 x 2.8cm . Terminal Unit: 8.09 x 5.2 x 2.8cm Weight . Base + Terminal Unit: 4.1oz Temperature . Operating: 0°C to 40°C (32°F to 104°F) . Storage: -40°C to 70°C (-40°F to 158°F) Operating Humidity . 10% to 80% Warranty . 1 Year Specifications Features . Provides DC power over existing CAT 5 cabling to Access Points. . Transforms incoming AC power into low-voltage DC power. . Base and Terminal Power Over Ethernet modules powers any Network Device requiring 5V or 12V DC input. . Protects Access Points from possible damages due to power-surges. . Output: 5VDC, 2.5A or 12VDC, 1A LAN Computer D-Link Wireless Access Point DWL-P200 Power Over Ethernet (Base Unit) DWL-P200 Power Over Ethernet (Terminal Unit) Ethernet Cable DC Power Cable AC/DC Power Adapter Ethernet Cable

D-Link provides free technical support for customers within the United States and within Canada for the duration of the warranty period on this product. U.S. and Canadian customers can contact D-Link technical support through our website, or by phone. Tech Support for customers within the United States: D-Link Technical Support over the Telephone: (877) 453-5465 24 hours a day, seven days a week. D-Link Technical Support over the Internet: http://support.dlink.com email:[email protected] Tech Support for customers within Canada: D-Link Technical Support over the Telephone: (800) 361-5265 Monday to Friday 8:30am to 9:00pm EST D-Link Technical Support over the Internet: http://support.dlink.ca email:[email protected] Tech Support for customers within the Europe: D-Link Europe (United Kingdom) Ltd: 4th Floor, Merit House, Edgware Road, Colindale, London NW9 5AB United Kingdom TEL: 44-020-8731-5555 SALES: 44-020-8731-5550 FAX: 44-020-8731-5511 SALES: 44-020-8731-5551 BBS: 44 (0) 181-235-5511 D-Link Technical Support over the Internet: http://support.dlink.co.uk Email:[email protected]