Coleman Quickbed Instructions

Instructions WARNING: Read airbed instruction manual and follow all safety instructions to avoid serious injury or death. Not for use by children 3 and younger or people with limited mobility. They may suffocate in a face down position or become trapped and suffocate in the gap between the airbed and adjacent furniture or wall. If the airbed is under inflated or deflates during use, this risk of suffocation may increase. Do not let young children sleep on this airbed until they are mature enough to sleep in an adult bed. Young children can suffocate on adult beds (including airbeds), particularly when sleeping with another person. Ask your pediatrician for specific recommendations for your child. Adult supervision required for inflation and deflation. This airbed can melt or burn. Keep away from open flames, heaters, and other hot objects. Do not smoke on or near the airbed. This airbed is not for use in water. It is not a life saving device personal flotation device, or water toy. This airbed is not a toy. Do not stand, walk, jump or play on the airbed. This can result in serious injury or damage to the airbed. Inflation Instructions To Inflate using Coleman® QuickPumpTM Unit: • To begin inflation, open external cap and pull firmly on lanyard to extend out. This will open internal yellow seal. • Attach nozzle to inflation end of Pump. Insert nozzle and turn on. NEVER USE A HAIR DRYER TO INFLATE For video instructions go to www.coleman.com/inflate DO NOT OVER INFLATE • When fully inflated, seal valve by pushing in with pump nozzle. This will seal the inter- nal yellow stopper and keep air from escaping while closing cap. • Fully remove pump and close external stopper. Valve should appear depressed into itself. To Deflate without use of pump: Remove adapter nozzle from inflation end and attach to opposite deflation side of pump. Repeat same steps as inflation. This will draw the air out quickly. To deflate, open external stopper and pull to extend out allowing air to escape. When fully deflated close stopper. Important Information • Do not let inflatable products come in contact with sharp, pointed objects. • Fill with cold air only. Never use a hair dryer to inflate, this could cause melting. • Do Not Over Inflate. Bursting items can cause serious injury. Inflate the airbed until most of the wrinkles in the material are gone and the bed feels firm to the touch. Caution: Air temperature and weather do affect the air pressure in inflatable products. In cold weather your airbed will lose some pressure do to the fact that the air will contract. If this occurs, you may want to add a little air to improve your airbed’s performance. However, in hot weather, the air will expand. You must let some air out to prevent the airbed from failing due to overpressure. You should avoid exposing your airbed to extreme temperatures (hot or cold). To Close Valve Fully Opened Valve • Firmly pull cap to unseat valve from inner yellow post. Internal Yellow Post Pull to Open OPEN - STEP 2: Internal Seal Closed • Reverse Steps 1 & 2. Make sure valve seats on inner yellow post. Push to Close Fully Closed Valve • Close cap. To Open / Close Valve Internal Seal Closed • Pull open cap. OPEN - STEP 1: Deflation Instructions To Deflate using Coleman® QuickPumpTM Unit: 4010005306 (20090402)

Instructions (continued) Storage Steps 1. Deflate Airbed (Step 1) (Leaving the Double LockTM Valve open while rolling will help remove any remaining air for more compact storage.) 2. Fold bed as shown. (Step 2) 3. Roll up the Airbed toward the storage flap. (Step 3) 4. Wrap storage flap around rolled bed and tie ends to secure. (Step 4) Sheet Clip Instructions (applicable models only) 1. Lift up on tab to open clip and insert the edge of sheet. (Fig. 1) 2. Insert tab into slot and push down to close. (Fig. 2) Wrap ’N’ RollTM Storage System Sheet Fig. 2 Slot Sheet Fig. 1 Tab Please call or write us with any comments or questions. The Coleman Company, Inc. • 3600 N. Hydraulic • Wichita, KS 67219 U.S.A. 1-800-835-3278 • TDD: 1-316-832-8707 • www.coleman.com Sunbeam Corporation (Canada) Limited • DBA Jarden Consumer Solutions • 20B Hereford Street • Brampton, ON L6Y 0M1 1 800 387-6161 ©2009 The Coleman Company, Inc. All rights reserved. Made in China. The Coleman Company, Inc., a Jarden Corporation company (NYSE:JAH) Coleman®, QuickBed®, , and are registered trademarks and QuickPump™, Double Lock™, and Wrap ‘N’ Roll™ are trademarks of The Coleman Company, Inc.