Plantronics Voyager Focus UC Quick Start Manual

• Automatically manage your PC multimedia so you never miss a call • Quickly access links to product support and software/firmware upgrade information Registering Your Product and Plantronics Software Visit plantronics.com/productregistration to register your product online so we can provide you with the best service and technical support. We also recommend that you install the Plantronics software located at plantronics.com/ software. With it installed you can: Voyager Focus UC Quick Start Guide ANC ������� Charge stand USB Bluetooth adapter Volume up/down Track backward* Play/pause music* Track forward* Active noise cancelling Charge port Active call = mute/unmute Idle = OpenMic (hear your surroundings) Headset LEDs for pairing, battery status, online indicator Call button ([ ]) Power button Bluetooth pair button

side, rotate the microphone boom up and over. Adjust the boom so it points to the corner of your mouth. TIP Your headset senses when you change the microphone boom from one side to the other and syncs the audio and controls specific to each side. Charging your headset IMPORTANT Before using, charge the headset fully to reset the accuracy of the talk time prompts. Charge your headset with the charge stand or the micro USB cable. The headset LEDs flash when charging. It takes up to 2 hours to fully charge your headset. The LEDs turn off once charging is complete. NOTE Both the charge stand and micro USB cable can be plugged into either a computer or wall charger. It is only necessary to plug into a computer to update firmware. Charge stand Micro USB cable Headset LEDs Battery status 4–5 blue blinks Battery high 2–3 blue blinks Battery medium 1 red blink Battery low flashing red Battery critical; Recharge headset Your Bluetooth USB adapter comes pre-paired to your headset. 1 Insert the Bluetooth USB adapter into your laptop or PC. 2 Pairing is successful when you hear “pairing successful” and the USB adapter LED is solid blue. 3 OPTIONAL: Headset call control Some softphones require the installation of Plantronics Hub for Windows and Mac (plantronics.com/software) to enable headset control (answer/end and mute) functionality. NOTE Plantronics Hub software also allows you to customize your headset's behavior through advanced settings and options. Your high-fidelity Bluetooth USB adapter comes ready to take calls. If you want to listen to music, you will need to configure your Bluetooth USB adapter. Windows 1 To configure your Bluetooth USB adapter to play music, go to Start menu > Control Panel > Sound > Playback tab. Select Plantronics BT600, set it as the Default Device and click OK. 2 To pause music when you place or receive calls, go to Start menu > Control Panel > Sound > Communications tab and select the desired parameter. Mac 3 To configure the Bluetooth USB adapter, go to Apple menu > System Preferences > Sound. On both the Input and Output tabs, select Plantronics BT600. Connect to PC Configure USB adapter

To put your headset in pair mode, press and hold the power button towards the Bluetooth icon until you hear "pairing" and the headset LEDs flash red and blue. 2 Activate Bluetooth on your phone and set it to search for new devices. • iPhone Settings > Bluetooth > On* • Android Settings > Bluetooth: On > Scan for devices* NOTE *Menus may vary by device. 3 Select “PLT_Focus.” If necessary, enter four zeros (0000) for the passcode or accept the connection. Once successfully paired, you hear “pairing successful” and the headset LEDs stop flashing. NOTE Your headset can pair with up to 8 devices but only maintain 2 connections simultaneously; this includes the Bluetooth USB adapter. Some softphones require the installation of Plantronics Hub for Windows and Mac to enable headset control (answer/end and mute) functionality. 1 Install Plantronics Hub for Windows and Mac onto your computer by visiting plantronics.com/ software. 2 Manage your headset settings with your computer or mobile device with Plantronics Hub for Windows and Mac or Plantronics Hub for iOS and Android, respectively (plantronics.com/ software). Plantronics Hub iOS and Android Windows and Mac Call control for softphones X Change headset language X Update firmware X Turn features on/off X X View user guide X Battery meter X X Load Software

If your smartphone has a voice-enabled assistant, press and hold the Call button for 2 seconds and wait for the phone prompt and then tell the phone to dial the number of a stored contact. While on an active call, choose: • Tap the red Mute button • Take off/put on your headset while on an active call (requires active smart sensors) * Plantronics Hub for Windows and Mac required (plantronics.com/software) If you have muted an active call and you start to speak, then a desktop notification reminds you that you are on mute. You can add a voice prompt notification by managing your mute features with Plantronics Hub for Windows and Mac. While not on a call, tap the red Mute button to activate OpenMic and hear your surroundings. Control the level of ambient noise you hear by adjusting the volume wheel. Rotate the volume wheel forward (+) or backward (–) to control the volume. Choose: • Put on/take off the headset (requires active smart sensors) • Tap the Play/pause button NOTE Functionality varies by application. Does not function with web-based apps. Tap the Forward button or Back button to control the track selection. NOTE Functionality varies by application. Does not function with web-based apps. Mute/unmute Mute on reminder* OpenMic Volume Play or pause music Track selection NOTE *Functionality varies by application. Does not function with web-based apps. Answer or end a call: Tap the Call button. Make/Take/End Calls Call back last call (smartphone): To dial your last number you dialed, double-tap the Call button.

putting on the headset will: taking off the headset will: Call answer the call mute the headset Music/media resume music/media (if playing previous to taking off)* pause music/media (if playing)* Mute unmute if on an active call mute if on an active call NOTE *Functionality varies by application. Does not function with web-based apps. Reset sensors You may need to reset the sensors if they are not working as expected. There are two ways to reset the headset sensors. Choose: • • With your headset powered on, charge your headset on the charge stand for 10 seconds Press and hold both the Mute and Play/pause buttons for more than 4 seconds until the LEDs flash purple twice, being careful to not touch the earcup padding or allow it to come in contact with surfaces Disable sensors You can disable your headset smart sensors several ways: Use sensors • Manage sensors through Plantronics Hub software • Hold both the Mute and Call buttons for more than 4 seconds until the LED flashes purple then red. Repeat to reactivate; the LED flashes purple then blue. NOTE Sensors cannot be disabled while streaming audio. Active Noise Cancelling (ANC) reduces unwanted noise. Your headset ships with ANC on. To turn ANC off, slide the stitch away from "ANC." ANC