SIP T126 Instructions Manual

2 4 3 6 1 7 5 8 Ref. No. Description Sip Part No. Ref. No. Description Sip Part No. 1. Cylindrical Shroud 02684 5. Shroud Spring 09084 2. Conical Shroud 09086 6. Insulator WE02-00061 3. Tip 0.6mm 09070 7. Swan Neck 02712 3. Tip 0.8mm 09080 8. Handle set WE02-00063 3. Tip 0.9mm 09074 N/A Gas valve WE02-00062 4. Gas diffuser WE02-00060 3 CONTENTS Page No. Description 4. Safety Symbols Used Throughout This Manual 4. Safety Instructions 11. Electrical Connection 12. Guarantee 13. Technical Specification 14. Contents and Accessories 15. Getting to Know Your MIG ...

gas cylinders all use the same regulator. Refillable gas bottles Argon, Argon CO2 and Argon O2 use the same regulator with a male thread , CO2 uses a different regulator . GAS SELECTION (T136 & T166) The Weldmate T126 has 2 power settings (see left diagram). Low High POWER SETTINGS The polarity of the welding torch and earth return lead is based on the wire type to be used, see table below. SETTING THE POLARITY (T136 & T166) Metal Type Wire Type Link Lead Earth Lead ...

11 ELECTRICAL CONNECTION WARNING! It is the responsibility of the owner and the operator to read, understand and comply with the following: You must check all electrical products, before use, to ensure that they are safe. You must inspect power cables, plugs, sockets and any other connectors for wear or damage. You must ensure that the risk of electric shock is minimised by the installation of appro- priate safety devices; A residual current circuit Breaker (RCCB) should be incorporated in the main distribution board. We also recommend that a residual cu ...

toxic; always wear a face mask . When using the mig welder always ensure the operator as well as those in the area use a welding mask with the correct shade filter lens. CAUTION: The warnings and cautions mentioned in this user manual can not cover all possible conditions and situations that may occur. It must be under- stood by the operator that common sense and caution are factors which can- not be built into this product, but must be applied. 27 WIRING DIAGRAM WELDMATE T166 MIG ...

Ref. No. Description 1. Torch Handle 2. Swan Neck 3. Shroud Spring 4. Gas Diffuser 5. Mig Tip 6. Conical Shroud 7. Cylindrical Shroud 8. Trigger Switch 2 4 3 6 1 7 5 8 A B C D E F G H I J K Ref. No. Description Ref. No. Description A. Gas Hose Fitting G. Pressure Roller B. Spool Holder H. Liner C. Overload I. Wire Feed Roller D. Fuse Holder J. Pressure Adjust Knob E. Red Positive Terminal K. Inlet Guide F. Black Negative Terminal L. Tension Arm L 19 ASSEMBLY INSTRUCTIONS WELDING MASK ASSEMBLY Locate the welding mask, handle and filter lens (above, ...

for repair, or contact SIP technical for more advise. 13 TECHNICAL SPECIFICATION Note: Only the Weldmate T126 & T136 can be operated from a 13A sup- ply, using the Weldmate T166 from a 13A supply will invalidate the warran- ty. Model Weldmate T126 (Gasless) Weldmate T136 (Gas / Gasless) Weldmate T166 (Gas / Gasless) Input Voltage 230v ~ 50Hz 230v ~ 50Hz 230v ~ 50Hz Input Current 13 amps 13 amps 16 amps Maximum OCV 31V (AC) 30V (DC) 32V (DC) Output Current (Amps) 60 - 125 (Peak) 30 - 135 (Peak) ...