Photron HS-01 Hardware Manual

• Product specifications and manual contents can change without advanced notification. • This manual was created taking every possible measure to ensure the accuracy of its contents. However, if you find a section which is unclear, a mistake, or an omission, please contact PHOTRON LIMITED using the contact information provided at the end of the manual. • PHOTRON LIMITED bears no responsibility for the results of using the product or from following the instructions in this manual. WARNING This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the users will be required to correct the interference at their own expense. CAUTION: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

Head HS-01” (referred to below as the system). This manual contains the operating instructions and warnings necessary for using the system. Before using the system, please read the entire manual. If any part of this manual is unclear, contact Photron using the contact information printed at the back of the manual. After you finish reading the manual, store it in a safe place along with the warranty card and refer back to it when necessary. Manual Notation The following icons and symbols are used in the explanations in this manual. Icon/Symbol Description This symbol indicates content that should always be read. This symbol indicates instructions that should always be followed when using the software, or things to be careful of when using the software. This symbol indicates supplementary items to be aware of when using the system. This symbol indicates the location of a reference. This symbol indicates a space for you to make notes. “ “ This symbol is used to indicate the names of items on a screen, references, dialog names, and connectors. ［ ］ This symbol is used to indicate menu names, and sub-menu names.

This section explains the layout of the manual. For other options, please refer to each manual. Introduction The introduction explains the manual and safety precautions. Chapter 1. Overview This chapter gives an overview of the system and an explanation of its features. It also explains a list of items that should be checked before using the system, and the procedure for connecting each component of the system. Chapter 2. Function This chapter explains the system’s functions. Refer to the “Photron FASTCAM Viewer User’s Manual” for additional details on using a PC to control the system. Chapter 3. Specifications This chapter explains the system’s specifications. Chapter 4. Warranty This chapter explains about the warranty. Chapter 5. Contacting Photron This chapter lists the contact information to use when contacting Photron if the system malfunctions or if a portion of the manual is unclear.

In order to prevent injury to yourself and others, and to prevent damage to property, carefully observe the following safety precautions. Photron has given its full attention to the safety of this system. However, the extent of damage and injury potentially caused by ignoring the content of the safety precautions and using the system incorrectly is explained next. Please pay careful attention to the content of the safety precautions when using the system. This symbol indicates actions that carry the risk that a person could receive a serious injury. This symbol indicates actions that carry the risk that a person could receive a moderate injury, or that damage to physical property might occur. The safety precautions to be observed are explained with the following symbols. This symbol indicates actions that require caution. This symbol indicates actions that are prohibited and must be avoided. This symbol indicates actions that must always be performed. Caution Warning

(Do not damage the cable, modify it, use it near a heater, excessively bend, twist or pull on it, place heavy objects on it, or bundle it.） Using the cable when damaged can cause fire, electric shock, or a short circuit. ■ Do not use the system in a manner which will exceed the rating of the power outlet or wiring equipment used. Exceeding the power rating might cause a fire from excessive heat. ■ Do not insert metallic objects inside, or pour liquids such as water on, the system. Doing so can cause fire, electric shock, or malfunction from short circuit or heat. ■ Do not disassemble or modify the system. There are high voltages inside the system that can cause electric shock. ■ Do not plug in or unplug the power cord with wet hands. Doing so can cause electric shock. ■ This chapter lists the contact information to use when contacting Photron if the system malfunctions or if a portion of the manual is unclear. Not fully plugging in the power cable can cause fire from electric shock or heat. ■ When something is wrong with the system, unplug the power cable immediately. - When a foreign substance or liquid, such as metal or water, gets inside. - When the outer case is broken or damaged, such as from a fall. - When the system produces smoke, a strange smell, or strange sound. Using the system in these conditions might cause a fire or electric shock. ■ Do not use the accessories by the usage that a manufacturer does not specify. It may cause damage of protection. Warning

Leaving or storing the system connected to the power source might cause fire from insulation deterioration or electrical discharge. ■Please consult us in advance when you perform an event by which laser light or direct rays fall on the image sensor surface. ■ Do not set the system in a location where the temperature gets unusually hot. The trunk and inside of a car can get especially hot in summer. Doing so can cause the outer case and internal components to deteriorate or cause a fire. ■ Do not place the system in a location prone to oily smoke or steam, or in a location with a lot of humidity or dust. Oil, moisture, and dust conduct electricity, which can cause a fire or electric shock. ■ Do not obstruct the air intake and exhaust port, when the system is installed. ■ Ambient temperature 0-45° C, humidity 85% RH or lower, maximum altitude 2,000m or lower. In addition, if exceeding these limits, use in a condensation-free environment. Doing so can cause malfunction. ■ Do not store the equipment in a location where the temperature goes below -20°C or higher than 60°C. Also, prevent condensation from forming during shipment ■ When shipping, remove the connecting cable and use the original packaging or a dedicated carrying case. Do not ship the equipment in an environment where the temperature goes below -20°C or higher than 60°C. Also, prevent condensation from forming during shipment Caution

waste, according to the WEEE Directive (2012/19/EU), the Battery Directive (2013/56/EU) and/or your national laws implementing those Directives. This product should be handed over to a designated collection point, e.g., on an authorized one-for-one basis when you buy a new similar product or to an authorized collection site for recycling waste electrical and electronic equipment (EEE) and batteries and accumulators. Improper handling of this type of waste could have a possible impact on the environment and human health due to potentially hazardous substances that are generally associated with EEE. Your cooperation in the correct disposal of this product will contribute to the effective usage of natural resources. For more information about the recycling of this product, please contact your local city office, waste authority, approved scheme or your household waste disposal service or visit www.photron.com. (EEA: Norway, Iceland and Liechtenstein) European Union (and EEA) only

image sensor. Please read the following instructions and take EXTREME CARE when cleaning the image sensor surface. ■ ALWAYS take appropriate anti-static precautions when cleaning or working near the Image sensor. ■ DO NOT use any form of cleaning equipment using electrostatic or ‘charged fiber’ technology. ■ Please discharge any electrostatic build up in your body by touching a grounded metallic Surface before working near the camera sensor. ■ Very gently, use only clean and dry air to remove dust from surface of the image sensor. ■ To remove stubborn contamination use the highest grade (e.g. VLSI grade) pure Isopropyl alcohol (IPA) with optical wipes of ‘clean room’ grade. ■ Extreme care must be taken! Gently wipe across the sensor in a single action. (DO NOT rub to avoid abrasive damage to delicate optical coatings on the glass surface.) Cleaning of the Image Sensor Surface

camera cable to give an ample space for the curvature. ■ Do not give an excessive impact or load to camera cables to avoid damage. ■ Whenever the cables are out of use, place the attached connector caps for protection of the connectors. ■In operation, connect the main unit’s connector cap and the camera cable’s connector cap each other to avoid dirt and pollution and to keep clean inside. The camera cable includes optics fibers. If dust or dirt is in inside of a connector, it may cause a communication error. Keep clean the inside of connectors. If a connector is polluted, clean the fiber edges by following instruction or using the bundled cleaning kit. ■ DO NOT use hard and/or sharp materials for cleaning. ■ Very gently, use only clean and dry air to remove dust from surface of the image sensor. ■ To remove stubborn contamination use the highest grade (e.g. VLSI grade) pure Isopropyl alcohol (IPA) with optical wipes of ‘clean room’ grade. Camera Cable

Chapter 1. Overview 1 1.1. Product Overview and Features .............................................................................. 2 1.2. System’s Components and Accessories .................................................................. 3 1.2.1. Components ................................................................................................ 3 1.2.2. Accessories/Options ................................................................................... 3 1.2.3. Type ............................................................................................................ 4 1.3. Part Names .............................................................................................................. 5 1.3.1. Camera Head .............................................................................................. 5 1.3.2. Camera Head Part Names .......................................................................... 6 1.3.3. Interchangeable Lens Mounts..................................................................... 7 1.4. Connection ............................................................................................................... 8 Chapter 2. Functions 11 2.1. Selecting Frame Rate ............................................................................................ 12 2.2. Selecting Resolution .............................................................................................. 12 2.3. Selecting Shutter Speed ........................................................................................ 13 2.4. Selecting Trigger Mode .......................................................................................... 14 2.4.1. START Mode ............................................................................................. 14 2.4.2. CENTER Mode ......................................................................................... 14 2.4.3. END Mode................................................................................................. 15 2.4.4. MANUAL Mode ......................................................................................... 15 2.4.5. RANDOM Mode ........................................................................................ 15 2.4.6. RANDOM RESET Mode ........................................................................... 16 2.4.7. RANDOM CENTER Mode ........................................................................ 17 2.4.8. RANDOM MANUAL Mode ........................................................................ 18 2.5. LOW LIGHT Mode ................................................................................................. 19 2.6. VARIABLE Setting ................................................................................................. 19 2.7. White Balance Adjustment (Color Model Only) ..................................................... 20 2.7.1. Using Preset White Balance (Color Model Only) ...................................... 20 2.7.2. Using User White Balance (Color Model Only) ......................................... 20 2.8. Color Enhancement Function (Color Model Only) ................................................. 21 2.9. Look-Up Table (LUT) Operations ........................................................................... 21 2.9.1. Using a Custom LUT ................................................................................. 24 2.10. Edge Enhancement Function ................................................................................ 24 2.11. Partition Memory & Record .................................................................................... 24 2.12. Event Marker Function ........................................................................................... 25 2.13. Direct Trigger / Direct Start Mode .......................................................................... 25 2.14. Fan Control ............................................................................................................ 26 Chapter 3. Specifications 27

3.1.1. Product Specifications .............................................................................. 28 3.1.2. General Specifications .............................................................................. 29 3.1.3. Frame Rate and Resolution ...................................................................... 30 3.1.4. Shutter Speed List .................................................................................... 33 3.1.5. Recordable Image Count/Resolution ........................................................ 34 3.1.6. Recordable Time/Resolution ..................................................................... 35 3.2. Dimensions ............................................................................................................ 36 3.2.1. Camera Body ............................................................................................ 36 3.2.2. Clearance for Camera Cable Connection ................................................. 39 Chapter 4. Warranty 41 4.1. About the Warranty ................................................................................................ 42 Chapter 5. Contacting Photron 43 5.1. Contact Information................................................................................................ 44

1.1. Product Overview and Features 1.2. System’s Components and Accessories 1.3. Part Names 1.4. Connection 1 FASTCAM Multi Camera Head HS-01

1.1. Product Overview and Features The Multi camera head HS-01 is a compact and lightweight camera head specifically designed for the FASTCAM Multi. It only weighs 0.98 Kg and supports 1,280 x 1,024 pixel resolution at 4,800 frames per second. The Multi camera head HS-01 can be utilized in a variety of applications including industrial R&D (design, quality control, and component technology development), science, medical, and aerospace. The Multi camera head HS-01 has adopted a robust design where circuit boards are completely sealed from the outside and a FAN OFF function is a standard feature for image measuring purposes. It also offers a wide range of optional parts such as Micro Four-Thirds (MFT) lens control and built-in LED lights. Use the Multi camera head HS-01 in a variety of applications with its multi-function, high-performance, robust, and expandable specifications to take full advantage of it. FASTCAM Multi Camera Head 2

1.2.1. Components The system’s standard components are listed below. Remove the components from the package and check them. 1. Camera Head (with G type F mount and lens cap) One 2. C mount adapter (with lens cap) One 3. FASTCAM Multi Camera Head HS-01 Hardware Manual (This Manual) One • Lens is not included in the product package. 1.2.2. Accessories/Options Connect this camera to the FASTCAM Multi Main Unit for operation. The following optional items are available to choose from (as of March 2015). 1. FASTCAM Multi Camera Cable 5m (102481) 2. FASTCAM Multi Camera Cable 10m (102482) 3. FASTCAM Multi LED Light Option (102483) 4. Micro Four Thirds Lens Option For FASTCAM Multi (102484) • In addition to the above, optional accessories such as lenses and lighting equipment are available. For details, ask your local sales representative, or see the contact information in Chapter 5.1. 3 FASTCAM Multi Camera Head HS-01

1.2.3. Type Four different types are available to choose from the below table. Max Frame Rate Sensor Type 750,000fps Monochrome FASTCAM Multi Camera Head HS-01 type 750K - M Color FASTCAM Multi Camera Head HS-01 type 750K - C 200,000fps Monochrome FASTCAM Multi Camera Head HS-01 type 200K - M Color FASTCAM Multi Camera Head HS-01 type 200K - C • Export-controlled model type 200K is subject to restriction on the frame rate and shutter speed. • Subject to restrictions under Export Trade Control Order, your camera may NOT be used depending on the country where you intend to use. If you are considering using your camera outside Japan, check with Photron first. Contact information is given in 5.1. Contact Information. 4

For each of the system components. - Do not expose to shock. - Do not use in an area where flammable gas or dust is present. - Do not place in an unstable location such as on an unstable platform or an incline. - Do not disassemble or modify. - Do not expose to liquids such as water. - Do not subject to excessive force. 1.3.1. Camera Head This is a camera head specifically designed to shoot a fast-moving object. It has imaging function only and the image data is transferred via the camera cable to the memory built in the main unit. On the rear panel of the camera, there are a connector for the camera cable to be used for communication between the camera and the main unit, and a power connector to feed power to the LED light option. Front Rear FASTCAM Multi Camera Head HS-01 5 FASTCAM Multi Camera Head HS-01

1.3.2. Camera Head Part Names Camera Cable Connector Power Connector For LED Light Laser Pointer Switch Front Back FASTCAM Multi Camera Head HS-01 G type F mount LED Light Switch Power Connector for LED Light, LED Light Switch and Laser Pointer Switch are used with FASTCAM Multi LED Light Option. 6

The lens mount on the system can be changed according to the recording purpose. There are 2 types of interchangeable lens mounts: “G type F-mount” and “C-mount”. In addition, it is possible to change over to the Micro Four Thirds lens mount by acquiring a “Micro Four-Thirds Lens Option for FASTCAM Mult”. How to change the lens mount (G type F-mount → C-mount) 1. Remove the four M3 Hex Socket Cap screws using the hexagonal wrench. 2. Remove the G type F-mount portion as a unit. 3. Install the C-mount unit using the Hex Socket Cap screws in the 90° diagonal holes. 4. After installation, always verify that the unit is not loose and does not rattle. G type F mount (Standard) C mount 7 FASTCAM Multi Camera Head HS-01

1.4. Connection Following the below steps, connect between Main Unit and a camera head using the dedicated cables. 1. Make sure the power to the Main Unit is off. 2. Grasp and slide the grip of the connector, and then remove the cap from the camera cable. Connect the caps each other to avoid dirt and pollution and to keep clean inside. 3. Connect the camera cable. Make sure of the connector on the camera head and Main Unit. See the position of the red mark on the cable-mount connector and the box-mount connector to be connected. Main Unit Camera Head Camera Cable Connector Main Unit Connector Main Unit/Camera Head Connector Cap Camera Cable Connector Cap 8

Grasp and slide the grip of the connector, and then disconnect the camera cable. • The camera cable has no dedicated orientation: the connector on either end can be connected to either the processor or the camera head. Be sure to verify if the camera cable has been correctly and firmly inserted. If the camera cable is disconnected for any reason while the camera is active, an error will result. Be sure to shut down the Main Unit before connecting or disconnecting the camera head. If the camera head is connected or disconnected while the system is powered, an error will result. Camera Cable Connector 9 FASTCAM Multi Camera Head HS-01

2.1. Selecting Frame Rate 2.2. Selecting Resolution 2.3. Selecting Shutter Speed 2.4. Selecting Trigger Mode 2.5. LOW LIGHT Mode 2.6. VARIABLE Setting 2.7. White Balance Adjustment (Color Model Only) 2.8. Color Enhancement Function (Color Model Only) 2.9. Look-Up Table (LUT) Operations 2.10. Edge Enhancement Function 2.11. Partition Memory & Record 2.12. Event Marker Function 2.13. Direct Trigger / Direct Start Mode 2.14. Fan Control 11 FASTCAM Multi Camera Head HS-01

2.1. Selecting Frame Rate Images can be recorded with the system from 50 fps to 4,800 fps using the full 1,280x1,024 pixel resolution of the image sensor. For frame rates higher than 4,800 fps, high-speed recording is achieved by limiting the read area of the image sensor. • Please refer to “3.3 Setting and Registering the Frame Rate/Resolution” of “Photron FASTCAM Viewer User’s Manual” for the details of the setup. • Even if a limited horizontal resolution is applied, Frame Rate cannot be increased. This specification is different from other systems. Please refer to “3.1.3. Frame Rate and Resolution” page 30 for available frame rate. • Export-controlled model type 200K is subject to certain restriction on the frame rate. 2.2. Selecting Resolution The maximum resolution of the image sensor is 1,280 x 1,024: total 1,310,720 pixels. By reducing the resolution, images can be taken with even faster frame rates, or the recording duration can be extended accordingly. • Please refer to “3.3 Setting and Registering the Frame Rate/Resolution” of “Photron FASTCAM Viewer User’s Manual” for the details of the setup. 12

The shutter speed (Exposure time) is independent of the frame rate, and it is possible to control the exposure time in the frame using the electric shutter. By making an exposure that is of a shorter period than the frame rate, high-speed objects can be photographed blur-free. The shortest setting value of shutter speed is 1/949,668 sec (1.053 usec). • Please refer to “3.4 Setting the Shutter Speed” of “Photron FASTCAM Viewer User’s Manual” for the details of the setup. • A minimum exposure time depends on a set up frame rate. • Export-controlled model type 200K is subject to certain restriction on the shutter speed. Frame Rate Limitation 50fps 1/60 ~ 1/312,500 sec (3.20 usec) are selectable 60fps ~ 200,000fps 1/frame ~ 1/312,500 sec (3.20 usec) are selectable 240,000fps 1/frame sec (4.17usec) is only available 250,000fps 1/frame sec (4.00 usec) is only available 300,000fps ~ 600,000fps 1/frame ~ 1/750,000 sec (1.33 usec) are selectable 625,000fps 1/frame sec (1.60 usec) is only available 750,000fps 1/frame sec (1.33 usec) is only available 13 FASTCAM Multi Camera Head HS-01

2.4. Selecting Trigger Mode In order to reliably capture high-speed phenomena, many kinds of trigger modes have been made available. These trigger modes are explained next. There are eight types of trigger modes which are listed below. START CENTER END MANUAL RANDOM RANDOM RESET RANDOM CENTER RANDOM MANUAL • Please refer to “3.5 Setting the Trigger Mode” of “Photron FASTCAM Viewer User’s Manual” for the details of the setup. 2.4.1. START Mode START mode is a trigger mode where recording starts the instant the trigger is input, the scene is recorded until the memory is full, and then recording ends. This mode is suitable for taking images of high-speed phenomena when what will happen, and when it happens, is known in advance. For example, in a situation with a maximum useable memory of two seconds of recording, two seconds of high-speed video is saved immediately after the trigger is input. 2.4.2. CENTER Mode CENTER mode is a trigger mode where an equal amount of content recorded before and after the trigger is input is saved to memory. This mode is suitable for viewing before and after an important instant. For example, in a situation with a maximum useable memory for two seconds of recording, one second before and one second after the trigger was input is recorded for a total of two seconds of high-speed video. 14

END mode is a trigger mode where the content recorded immediately before the trigger is input is saved to memory. This mode is suitable for recording a high-speed phenomenon where it is hard to predict when the important action will start and stop. For example, in a situation with a maximum useable memory for two seconds of recording, the two seconds of high-speed video immediately before when the trigger was input are saved. 2.4.4. MANUAL Mode MANUAL mode is a trigger mode, similar to CENTER mode, where the content recorded before and after the trigger is input is saved to memory, but the proportion of time before and after the trigger can be set as required. For example, in a situation with a maximum record time of two seconds, 0.5 seconds before and 1.5 seconds after the trigger is input are recorded and saved, a total of two seconds of high-speed video. 2.4.5. RANDOM Mode RANDOM mode is a trigger mode where each time a trigger is input only a predetermined number of frames are saved to memory. For example, this function is convenient for a subject which is an irregular and repeated phenomenon which can have a trigger output produced for each cycle or occurrence. The number of frames recorded each time the trigger is input can be set as desired, in one frame increments, from one frame to the maximum of all the recordable frames available. 15 FASTCAM Multi Camera Head HS-01

2.4.6. RANDOM RESET Mode RANDOM RESET mode is explained here by comparing its operation with the normal mode. RANDOM RESET mode is a mode to improve the temporal accuracy of the record start timing and the timing of the trigger input, where, to put it simply, with the input of the trigger signal, at the timing that it is input, the camera’s record timing is reset. When the camera is set to the normal RANDOM mode (the same as START mode) and RANDOM RESET mode, the difference in the recording operation for the trigger input is shown graphically. In the normal RANDOM mode and START mode, the camera starts recording when the trigger is input, but the internal record timing signal is independent and it operates regardless of when the trigger is input. For this reason, there may be situations where the start time of the first frame when the trigger is input is advanced almost a full frame. The range of this overlap also cannot be known. On the other hand, in RANDOM RESET mode, the camera’s internal record timing signal is reset by the trigger input and operates anew. For this reason, the trigger input time and the timing of the start of the first frame are the same. The interval from when the trigger is input until the exposure begins is approximately 1.75usec at slower than 256,000fps, 0.74usec at faster than 256,001fps. • When continuously shooting in Random Reset mode, DO NOT use an interval longer than 1-frame length (ex. 1/1000 sec interval in 1000 fps operation). 16

RANDOM CENTER mode is a trigger mode, similar to RANDOM mode, where each time a trigger is input only a predetermined number of frames are saved to memory. The difference between this mode and RANDOM mode is that in RANDOM mode the number of specified frames are recorded directly after the trigger signal, whereas in RANDOM CENTER mode, at the timing of the trigger signal, the frames before and after the trigger remain in the recording memory. For example, this function is convenient for a subject which is an irregular and repeated phenomenon which can have a trigger output produced for each cycle or occurrence, and you want to check the action before and after the trigger timing. The number of frames recorded each time the trigger is input can be set as desired, in one frame increments, from one frame to the maximum of all the recordable frames available. Setting the RANDOM CENTER mode frame count Setting the frame count in RANDOM CENTER mode is the same as setting the frame count for RANDOM mode. Setting the RANDOM CENTER mode record count The number of trigger inputs that can be accepted in RANDOM CENTER mode is a maximum of 10. Set the number of trigger inputs in advance, and the recording operation can be ended when that amount of trigger inputs is finished. • For how to setup of RANDOM Mode, refer to “2.4.5.RANDOM Mode” page 15. 17 FASTCAM Multi Camera Head HS-01

2.4.8. RANDOM MANUAL Mode RANDOM MANUAL mode is a trigger mode, similar to RANDOM mode, where each time a trigger is input only a predetermined number of frames are saved to memory. The difference between this mode and RANDOM mode is that in RANDOM mode the number of specified frames are recorded directly after the trigger input, whereas in RANDOM MANUAL mode, at the timing of the trigger input, the frames before and after the trigger, each specified as desired, remain in the recording memory. For example, this function is convenient for a subject which is an irregular and repeated phenomenon which can have a trigger output produced for each cycle or occurrence, and you want to check the action before and after the trigger timing. The number of frames recorded each time the trigger is input can be set as desired, in one frame increments, from one frame to the maximum of all the recordable frames available. Setting the RANDOM MANUAL mode record count Setting the record count in RANDOM MANUAL mode is the same as setting the record count for RANDOM CENTER mode. Setting the RANDOM MANUAL mode frame count To use RANDOM MANUAL mode, the proportion of frames to record before and after the trigger must be set in advance before recording. • For how to setup of RANDOM Mode, refer to “2.4.5.RANDOM Mode” page 15. 18

The more you increase the frame rate or shutter speed of the camera, the more the amount of light entering the camera decreases, making the displayed image darker. Low light mode is a function that temporarily increases the exposure time, making the displayed image easier to see to enable you to focus and setup the camera. The default shutter speed of this product is 1/50 second. • Please refer to “3.6 Using Low Light Mode” of “Photron FASTCAM Viewer User’s Manual” for the details of the setup. 2.6. VARIABLE Setting In the recording conditions settings, the frame rate and resolution can be set to the desired value following the conditions listed below.  FRAMERATE can be set from 54 frame rates between 50 fps and 750,000 fps.  The size and horizontal position of the resolution can be set in 128 (horizontal) and 8(vertical) increments.  The minimum resolution is 640 (horizontal) x 8(vertical)  The resolution is limited as of 128 (horizontal) and 8(vertical) at 300,000fps or above. • Please refer to “3.3 Setting and Registering the Frame Rate/Resolution” of “Photron FASTCAM Viewer User’s Manual” for the details of the setup. • The area cannot be moved to the vertical direction at the variable setting of the system. • Export-controlled model type 200K is subject to certain restriction on the frame rate and the shutter speed. 19 FASTCAM Multi Camera Head HS-01

2.7. White Balance Adjustment (Color Model Only) On digital video cameras, photographing white as pure white is described as "having the appropriate white balance." On the system's color models as well, in order to take images with the correct color representation, the white balance must be adjusted for the color temperature of the light source used. The intensity of each color, R, G, and B, can be adjusted on this system. By adjusting the balance of those three colors to match the light source used, the appropriate white balance can be achieved. Two methods are available for adjusting the white balance, preset and user-editable white balance. These methods are explained in this section. 2.7.1. Using Preset White Balance (Color Model Only) With the system, there are two types of white balance presets (5100K, 3100K) for use with common light sources. The suggested color temperature for these presets is listed below.  5100K (Daylight, Outdoors)  3100K (Halogen Light Source) 2.7.2. Using User White Balance (Color Model Only) User white balance can be set in order to achieve the most appropriate white balance for the light source used with the system and the conditions during recording. The values set here are stored in the Main Unit's internal memory as the user preset, and they can be loaded by selecting USER. There are also two methods for setting user white balance, AUTO USER and EDIT USER. • Please refer to “3.8 Other Settings” of “Photron FASTCAM Viewer User’s Manual” for the details of the setup. 20

Color models feature an image color enhancement setting. The image color enhancement level can be adjusted in five steps, including the OFF setting. Menu Display Contents OFF Turns the color enhancement mode off x0.5 (LEVEL1) Sets x0.5 color enhancement x1 (LEVEL2) Sets x1 (default) color enhancement x1.5 (LEVEL3) Sets x1.5 color enhancement x2 (LEVEL4) Sets x2 color enhancement • Please refer to “3.8 Other Settings” of “Photron FASTCAM Viewer User’s Manual” for the details of the setup. 2.9. Look-Up Table (LUT) Operations The LUT (Look-Up Table) refers to a reference table that defines the relationship between the pixel brightness gradation of the original image data taken and the brightness gradation displayed on a computer screen or video monitor. The system contains a hardware LUT function, and you can display the image data taken with improved contrast (light and dark sharpness) or make an object in the image stand out by emphasizing a specified gray level range. The LUT in the system and the relationship between it and video output and the PC software is explained below. • When an image is saved with its brightness converted with the LUT, the image saved is the image that has had its brightness converted. 21 FASTCAM Multi Camera Head HS-01

D1: Gain 1x The input is always linear output. This LUT is used for normal conditions. D2: Gamma 0.6 This LUT is 0.6.gamma correction D3: Gamma 0.45 This LUT is 0.45 gamma correction. 22

The gain is doubled and you can display the dark areas of the image emphasized. D5: Gain 4x The gain is doubled and you can display the dark areas of the image emphasized. This LUT emphasizes the dark portions even more than D4. D6: Reverse Gradation The input gradation is reversed and then displayed. 23 FASTCAM Multi Camera Head HS-01

2.9.1. Using a Custom LUT Creating a LUT pattern is done with PFV. • For the creation method of a LUT pattern, refer to “Photron FASTCAM Viewer User's Manual”. 2.10. Edge Enhancement Function With the system's edge enhancement setting, you can enhance the edges in the recorded image in four steps, including the OFF setting. Menu Display Contents OFF Edge enhancement off. LEVEL1 Edge enhancement set to weak. LEVEL2 Edge enhancement set to medium. LEVEL3 Edge enhancement set to strong. • Please refer to “3.8 Other Settings” of “Photron FASTCAM Viewer User’s Manual” for the details of the setup. 2.11. Partition Memory & Record The system contains internally 8 GB standard, or a maximum of 32 GB, of high-capacity memory for recording use. This recording memory can be partitioned and assigned to each recording. Memory is partitioned into equal sizes and a maximum of 64 partitions can be set. The partitioned sections are managed by ID numbers. Each section can be set with completely independent recording conditions, so this feature is convenient when taking consecutive recordings with changed conditions. • Please refer to “3.8 Other Settings” of “Photron FASTCAM Viewer User’s Manual” for the details of the setup. 24

With the system, it is possible to input an external signal during recording, at the instant the frame number is stored, and during playback you can immediately access, or jump to, the stored frame numbers (event markers). This a separate feature from the trigger point, by marking interesting points during recording, these points can be easily called up for review during playback. The event marker can store ten positions within a sequence. The frame number recording occurs on the pulse's edge, and the next frame after the pulse's edge is input is stored as the event marker. Event marker settings can be made with the "Remote controller (optional)" or PFV. 2.13. Direct Trigger / Direct Start Mode The system recording operation responding to an input trigger signal can be configured according to varies of customer’s needs. DIRECT TRIGGER Mode (This mode is NOT supported on PFV software trigger) START TRIGGER Mode Recording starts immediately upon the second trigger input. CENTER, END, MANUAL TRIGGER Mode Once the trigger signal is input, the camera will be shifted to endless recording state. DIRECT START Mode START TRIGGER Mode The same operation as when the direct trigger mode is off. CENTER, END, and MANUAL TRIGGER Modes Once the trigger signal is input, the camera is shifted to endless recording state. In this circumstance, either the “RECORD” button of PFV software or the GENERAL IN Connector under ReadyPos state, furthermore the “RECORD” button of LCD Remote Controller can trigger a record signal to the camera. • For details of how to set the camera to DIRECT START Mode, refer to “Remote Controller User’s Manual” or “Photron FASTCAM Viewer User’s Manual”. • For details of GENERL IN signal settings, refer to “4.4.1. GENERAL IN Signal Setting” of “FASTCAM Multi Hardware Manual”. 25 FASTCAM Multi Camera Head HS-01

2.14. Fan Control This camera head has a cooling fan inside. The fan can be stopped. And the functional condition is limited as within a safe temperature. The fan is operated forcibly when a camera is heated up. And this function is disabled until the internal camera head temperature falls down to under a threshold. • Please refer to “3.8 Other Settings” of “Photron FASTCAM Viewer User’s Manual” for the details of the setup. 26

3.1. Specifications 3.1.1. Product Specifications Image Sensor CMOS image sensor Sensor Resolution 1,280 x 1,024 pixels Frame Rate When full frame: 4,800fps max. When a frame segment: 750,000fps max. Lens Mount G type F mount, C mount, Micro Four Thirds mount (Option) Recording Bit Depth Monochrome 12bit Color RGB, each 12bit (Bayer color filter method) Shutter Method Electronic shutter Recording Method IC memory Trigger Mode START, CENTER, END, MANUAL, RANDOM RANDOM RESET, RANDOM CENTER, RANDOM MANUAL Gain Control Hardware LUT on camera Controllable via software Digital Interface Exclusive multi optical interface 28

Environment Conditions Storage Temperature -20°C ~ 60°C (No Condensation) -4ºF ~ 140ºF (No Condensation) Storage Humidity 85% or less (No Condensation) Operating Temperature 0 ~ 45°C (No Condensation) 32ºF ~ 113ºF (No Condensation) Operating Humidity 85% or less (No Condensation) Pollution degree Degree 2 according to IEC60664-1 Overvoltage category Category II according to IEC60664-1 Maximum use altitude 2,000m or lower External Dimensions Camera Body 70(H) x 69 (W) x 151.4 (D) mm, excluding protrusion 2.8”(H) x 2.7”(W) x6.0”(D) DC Power Supply Power Voltage 28V Power Consumption 25VA Power Consumption (with LED Light Option) 37VA Weight Camera Body 0.98kg, 2,16lb Photron has verified two types of AC cables, type A (standard for Japan, USA, Canada, etc.) and type SE (standard for Germany, France, etc.). However, when those cables cannot properly receive power when plugged in, use the proper AC cable for the region's standards and verify that AC cable works properly. For inquires regarding the recommended AC cable for each region, contact that region's Photron branch office or the distributor. 29 FASTCAM Multi Camera Head HS-01

3.1.3. Frame Rate and Resolution 1,280ｘ1,024 ~ 1,280ｘ144 Resolution Frame Rate (fps) 1,280 × 1,024 1,280 × 1,000 1,280 × 960 1,280 × 824 1,280 × 720 1,280 × 656 1,280 × 616 1,280 × 488 1,280 × 384 1,280 × 296 1,280 × 232 1,280 × 176 1,280 × 144 50 ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ 60 ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ 125 ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ 250 ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ 500 ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ 1,000 ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ 2,000 ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ 3,000 ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ 4,000 ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ 4,800 ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ 5,000 ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ 6,000 ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ 7,500 ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ 8,000 ✓ ✓ ✓ ✓ ✓ ✓ ✓ 10,000 ✓ ✓ ✓ ✓ ✓ ✓ 12,500 ✓ ✓ ✓ ✓ ✓ 16,000 ✓ ✓ ✓ ✓ 20,000 ✓ ✓ ✓ 25,000 ✓ ✓ 30,000 ✓ 40,000 50,000 60,000 75,000 80,000 100,000 125,000 200,000 300,000 400,000 500,000 600,000 750,000 The ✓ mark indicates a possible setting. The green items are the maximum resolution setting at that frame rate. This table is the list of default settings. Even finer settings are possible with the variable setting. 30

Resolution Frame Rate (fps) 1,280 × 104 1,280 × 72 1,280 × 56 1,280 × 48 1,280 × 40 1,280 × 32 1,280 × 16 50 ✓ ✓ ✓ ✓ ✓ ✓ ✓ 60 ✓ ✓ ✓ ✓ ✓ ✓ ✓ 125 ✓ ✓ ✓ ✓ ✓ ✓ ✓ 250 ✓ ✓ ✓ ✓ ✓ ✓ ✓ 500 ✓ ✓ ✓ ✓ ✓ ✓ ✓ 1,000 ✓ ✓ ✓ ✓ ✓ ✓ ✓ 2,000 ✓ ✓ ✓ ✓ ✓ ✓ ✓ 3,000 ✓ ✓ ✓ ✓ ✓ ✓ ✓ 4,000 ✓ ✓ ✓ ✓ ✓ ✓ ✓ 4,800 ✓ ✓ ✓ ✓ ✓ ✓ ✓ 5,000 ✓ ✓ ✓ ✓ ✓ ✓ ✓ 6,000 ✓ ✓ ✓ ✓ ✓ ✓ ✓ 7,500 ✓ ✓ ✓ ✓ ✓ ✓ ✓ 8,000 ✓ ✓ ✓ ✓ ✓ ✓ ✓ 10,000 ✓ ✓ ✓ ✓ ✓ ✓ ✓ 12,500 ✓ ✓ ✓ ✓ ✓ ✓ ✓ 16,000 ✓ ✓ ✓ ✓ ✓ ✓ ✓ 20,000 ✓ ✓ ✓ ✓ ✓ ✓ ✓ 25,000 ✓ ✓ ✓ ✓ ✓ ✓ ✓ 30,000 ✓ ✓ ✓ ✓ ✓ ✓ ✓ 40,000 ✓ ✓ ✓ ✓ ✓ ✓ ✓ 50,000 ✓ ✓ ✓ ✓ ✓ ✓ 60,000 ✓ ✓ ✓ ✓ ✓ 75,000 ✓ ✓ ✓ ✓ 80,000 ✓ ✓ ✓ ✓ 100,000 ✓ ✓ ✓ 125,000 ✓ ✓ 200,000 ✓ 300,000 400,000 500,000 600,000 750,000 The ✓ mark indicates a possible setting. The green items are the maximum resolution setting at that frame rate. This table is the list of default settings. Even finer settings are possible with the variable setting. 31 FASTCAM Multi Camera Head HS-01

1,024 x 768 ~ 640 x 8 Resolution Frame Rate (fps) 1,024 × 768 1,024 × 576 896 × 672 896 × 504 768 × 576 768 × 432 640 × 480 640 × 360 640 × 8 50 ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ 60 ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ 125 ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ 250 ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ 500 ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ 1,000 ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ 2,000 ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ 3,000 ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ 4,000 ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ 4,800 ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ 5,000 ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ 6,000 ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ 7,500 ✓ ✓ ✓ ✓ ✓ ✓ ✓ 8,000 ✓ ✓ ✓ ✓ ✓ 10,000 ✓ ✓ ✓ ✓ 12,500 ✓ ✓ 16,000 ✓ 20,000 ✓ 25,000 ✓ 30,000 ✓ 40,000 ✓ 50,000 ✓ 60,000 ✓ 75,000 ✓ 80,000 ✓ 100,000 ✓ 125,000 ✓ 200,000 ✓ 300,000 ✓ 400,000 ✓ 500,000 ✓ 600,000 ✓ 750,000 ✓ The circle indicates a possible setting. The green items are the maximum resolution setting at that frame rate. This table is the list of default settings. Even finer settings are possible with the variable setting. Type 200K model cannot be set 300,000fps and faster frame rate. 32

Shutter Speed 50 6,000 80,000 60 7,500 100,000 125 8,000 120,000 250 9,600 125,000 500 10,000 150,000 750 12,000 187,500 1,000 12,500 200,000 1,500 16,000 240,000 1,600 20,000 250,000 2,000 25,000 300,000 2,000 30,000 312,500 2,400 37,500 375,000 2,500 40,000 400,000 3,000 48,000 500,000 3,200 50,000 600,000 4,000 60,000 625,000 4,800 62,500 750,000 5,000 75,000 The unit in the chart is 1/x sec, • At a frame rate 50 ~ 200,000fps, a shutter speed of 1/frame sec or lower in the green area in the above table can be selected. • At a frame rate 240,000fps, 250,000fps, 625,000fps and 750,000fps, a shutter speed of 1/frame sec is only available. • At a frame rate 300,000 ~ 600,000fps, every 1/frame sec or lower shutter speed can be selected. • For the type 200K, a shutter speed 1/375,000 sec or lower cannot be selected. 33 FASTCAM Multi Camera Head HS-01

3.1.5. Recordable Image Count/Resolution Resolution 8G Type Rec. Frames 16G Type Rec. Frames 32G Type Rec. Frames 1,280x1,024 4,363 8,733 17,471 1,280x1,000 4,467 8,942 17,890 1,280x960 4,654 9,315 18,636 1,280x824 5,422 10,853 21,712 1,280x720 6,206 12,420 24,848 1,280x656 6,811 13,632 27,272 1,280x616 7,254 14,518 29,043 1,280x488 9,157 18,326 36,662 1,280x384 11,683 23,290 46,591 1,280x296 15,098 30,214 60,443 1,280x232 19,264 38,549 77,117 1,280x176 25,394 50,815 101,655 1,280x144 31,038 62,108 124,246 1,280x104 42,977 85,996 172,033 1,280x72 62,078 124,217 248,493 1,280x56 79,816 159,708 319,491 1,280x48 93,119 186,327 372,740 1,280x40 111,743 223,592 447,289 1,280x32 139,680 279,491 559,111 1,280x16 279,362 558,983 1,118,224 1,024x768 7,273 14,555 29,119 1,024x576 9,698 19,408 38,826 896x672 9,500 19,012 38,033 896x504 12,667 25,349 50,712 768x576 12,931 25,877 51,768 768x432 17,242 34,504 69,025 640x480 18,622 37,264 74,547 640x360 24,830 49,686 99,396 640x8 1,117,455 2,235,937 4,472,899 * Recordable Time = Recordable Frames x 1/frame rate (fps) 34

Resolution MAX Frame Rate 8G Type Rec. Time 16G Type Rec. Time 32G Type Rec. Time 1,280x1,024 4,800 0.91 2.18 4.37 1,280x1,000 5,000 0.89 1.79 3.58 1,280x960 5,000 0.93 1.86 3.73 1,280x824 6,000 0.90 1.81 3.62 1,280x720 6,000 1.03 2.07 4.14 1,280x656 7,500 0.91 1.82 3.64 1,280x616 8,000 0.91 1.81 3.63 1,280x488 10,000 0.92 1.83 3.67 1,280x384 12,500 0.93 1.86 3.73 1,280x296 16,000 0.94 1.89 3.78 1,280x232 20,000 0.96 1.93 3.86 1,280x176 25,000 1.02 2.03 4.07 1,280x144 30,000 1.03 2.07 4.14 1,280x104 40,000 1.07 2.15 4.30 1,280x72 50,000 1.24 2.48 4.97 1,280x56 60,000 1.33 2.66 5.32 1,280x48 80,000 1.16 2.33 4.66 1,280x40 100,000 1.12 2.24 4.47 1,280x32 125,000 1.12 2.24 4.47 1,280x16 200,000 1.40 2.79 5.59 1,024x768 6,000 1.21 2.43 4.85 1,024x576 7,500 1.29 2.59 5.18 896x672 6,000 1.58 3.17 6.34 896x504 8,000 1.58 3.17 6.34 768x576 7,500 1.72 3.45 6.90 768x432 10,000 1.72 3.45 6.90 640x480 10,000 1.86 3.73 7.45 640x360 12,500 1.99 3.97 7.95 640x8 750,000 1.49 2.98 5.96 The unit in the chart is sec 35 FASTCAM Multi Camera Head HS-01

FASTCAM Multi Camera Head HS-01 (G type F mount) 3.2. Dimensions 3.2.1. Camera Body (mm) 17.8 190.4 150.8 9.1 69 38.8 35.9 35.5 45 39 0.5 39.3 69.9 (0.5) 77.80 47.80 28 6-M3 DEPTH4 ※Caution If installing a longer screw than the specified depth (in mm), its screw hole or the camera may be damaged. 36

(mm) 92.8 69.9 0.5 12 39 39.3 74.8 59.8 45.8 38.8 48 86.8 (0.5) 9.1 69 32.8 17.8 28 60 35.5 45 35.9 38.8 190.4 150.9 4-M4 DEPTH6 φ4.5 DEPTH5.5 6-M3 DEPTH4 1/4-20UNC DEPTH6 3/8-16UNC DEPTH6 ※Caution If installing a longer screw than the specified depth (in mm), its screw hole or the camera may be damaged. 37 FASTCAM Multi Camera Head HS-01

FASTCAM Multi Camera Head HS-01 (C mount) (mm) 161.3 150.8 9.1 69 10 0.5 69.9 39.3 (0.5) 77.80 47.80 17.8 28 6-M3 DEPTH4 ※Caution If installing a longer screw than the specified depth (in mm), its screw hole or the camera may be damaged. 38

4.1. About the Warranty This system has been shipped having undergone rigorous testing. However, in the unlikely event that it malfunctions due to a manufacturing defect, it will be repaired, at no charge, within the warranty period. Warranty Exceptions The following exceptions will result in fee-based repair, even within the warranty period. 1. Damage or malfunction as a result of fire, earthquake, water damage, lightning, other natural disasters, pollution, or the effects of abnormal voltage. 2. Damage or malfunction as a result of dropping or mishandling during shipment or when moving after purchase or misuse. 3. Consumable goods (cables) 4. When repair, adjustment, or alternation done by an entity other than Photron service has been performed on the system, or damage or malfunction that is determined to be attributed to a fault in the use the product. For inquires related to malfunction, contact the dealer where the product was purchased, or the nearest Photron office. • For inquires related to our product, refer to “5.1. Contact Information” page 44. Reference 42

5.1. Contact Information For inquires related to FASTCAM Multi Camera Head HS-01, contact Photron at the contact information listed below. Additionally, the following items will be verified when inquiring, so please prepare them in advance. Items Verified Concrete Example Contact Information Company, school or organization name, Customer contact name, Contact phone number, Contact e-mail address. Product Name FASTCAM Multi Camera Head HS-01 Serial Number Check on the nameplate seal. Condition of the system and what is known about it. Contact Information In Americas and Antipodes PHOTRON USA, INC. 9520 Padgett Street, Suite 110, San Diego, CA 92126-4426, USA Phone : 800-585-2129 or 858-684-3555 Fax : 858-684-3558 E-mail : [email protected] / www.photron.com In Europe, Africa and India PHOTRON EUROPE LIMITED The Barn, Bottom Road, West Wycombe, Buckinghamshire, HP14 4BS, U.K. Phone : +44(0) 1494 48 1011 Fax : +44(0) 1494 48 7011 E-mail : [email protected] / www.photron.com In China PHOTRON (SHANGHAI) LIMITED. Room 20C Zhao-Feng World Trade Building, No. 369 Jiangsu Road, ChangNing District, Shanghai 200050 China Phone : 021-5268-3700 Fax : 021-5268-3702 E-mail : [email protected] / www.photron.cn.com In other areas PHOTRON LIMITED 21F, Jimbocho Mitsui Bldg., 1-105 Kanda Jimbocho, Chiyoda-Ku, Tokyo 101-0051 Phone : +81 3 3518 6271 Fax : +81 3 3518 6279 E-mail : [email protected] www.photron.co.jp 44

Control No. E150609U-2 FFA ASSTTC CA AM M M Muullttii C Caam meerraa H Heeaadd H HSS--0011 Hardware Manual Revision 1.01E Publication Date June, 2015 Publisher PHOTRON LIMITED 21F, Jimbocho Mitsui Bldg., 1-105 Kanda Jimbocho, Chiyoda-Ku, Tokyo 101-0051