Phonic STUDIO WIZARD Operation & User’s Manual

apparatus. 2. Keep these instructions for future reference. 3. Heed all warnings to ensure safe operation. 4. Follow all instructions provided in this document. 5. Do not use this apparatus near water or in locations where condensation may occur. 6. Clean only with dry cloth. Do not use aerosol or liquid cleaners. Unplug this apparatus before cleaning. 7. Do not block any of the ventilation openings. Install in accordance with the manufacturer’s instructions. 8. Do not install near any heat sources such as radiators, heat registers, stoves, or ...

34. Mini Button Press this button to send the selected inputs to the mini speaker output on the main unit. 35. Main Button Press this button to send the selected inputs to the main speaker output on the main unit. 36. Alternative Button Press this button to send the selected inputs to the alternative speaker output on the main unit. Fader 37. Fade In Time Control Adjust this knob to set the fade in time. 38. Fade Out Time Control Adjust this knob to set the fade out time. 39. Master Button When the Master key is activated, the auto fader only applies to ...

This is a standard IEC power cable receptacle. Plug the power cable in here and connect the other end of the cable to an appropriate AC pow- er supply. 13. “To Remote" Connector This RJ-45 jack allows users to connect the main unit of the Studio Wizard to the remote desk-top controller. 14. Digital Inputs (S/PDIF and AES) These RCA and XLR inputs accept signals in S/ PDIF (RCA) or AES/EBU (XLR) format. Trans- fer rates are 24-bit, with sampling rates up to 192kHz (Mono). 15. Speaker Outputs These three stereo 1/4" TRS outputs provide balanced ...

fully ensure this, disconnect the AC cable. 2. Connect the Studio Wizard remote unit to the main unit using the supplied RJ-45 cable. 3. Connect your desired inputs to the Analog Inputs on the rear of the main unit. 4. If you have any products with S/PDIF or AES/EBU capabilities, you can connect the product’s S/PDIF output to the Studio Wiz- ard’s S/PDIF or AES inputs. 5. Depending on your requirements, you may wish to connect monitors to each of the Stu- dio Wizard’s outputs, or you may wish to conn ...

in a typical audio rack with the rest of your gear (amplifiers, equalizers, etc). On this unit you will find all of the Studio Wizards inputs and outputs, as well as trim controls ensuring that audio lev- els of the different inputs (and outputs) are not excessive. In any permanent set up, you may be able to plug your inputs and outputs into the Studio Wizard’s main unit and leave it alone from then on – all control over your audio can be achieved through the remote unit. FRONT PANEL 1. Talkback Select Switch This t ...

Type 1/4" TRS Balanced & RCA-unbalanced Input Impedance 2K Ω Balanced , 20K Ω unbalanced Nominal Line level setting +4dBu(center detented) Input level maximum +4 to +18dB unbalanced & Balanced Trim Range -∞to +18dB variable THD+N Less than .0005% (1KHz @ 0dBu) Frequency Response 10Hz-50KHz, +/-0.5dB S/PDIF Sample Rates Auto detect 24 bit, 44.1K, 48K, 96K, 192K(Mono) Types RCA 75Ω AES/EBU Sample Rates Auto detect 24 bit, 44.1K, 48K, 96K, 192K(Mono) Types XLR transformer balanced Audio Outputs Monitor out Type 1/4" TRS Balanced Nominal Li ...

apparatus. 2. Keep these instructions for future reference. 3. Heed all warnings to ensure safe operation. 4. Follow all instructions provided in this document. 5. Do not use this apparatus near water or in locations where condensation may occur. 6. Clean only with dry cloth. Do not use aerosol or liquid cleaners. Unplug this apparatus before cleaning. 7. Do not block any of the ventilation openings. Install in accordance with the manufacturer’s instructions. 8. Do not install near any heat sources such as radiators, heat registers, stoves, or ...