Simplex 4010 Installation Reference Manual

Front Panel Installing, Operating, and Programming Instructions 574-052 Rev. F Technical Manuals Online! - http://www.tech-man.com

Printed in the United States of America. Information in this document is subject to change without notice. No part of this document may be reproduced or transmitted in any form or by any means, electronic or mechanical, for any purpose, without the express written consent of Simplex Time Recorder Company. Walk Test is protected by US Patent No. 4,725,818. MAPNET addressable communications is protected by US Patent No.4,796,025. IDNet is patent pending. TrueAlarm Analog Detection is protected by US Patent No. 5,155,468. TrueAlarm Detector Base is protected by US Patent No. 5,173, 683. SYSTEM REACCEPTANCE TEST AFTER SOFTWARE CHANGES - To ensure proper system operation, this product must be tested in accordance with NFPA72-1996, Chapter 7 after any programming operation or change in site- specific software. Reacceptance testing is required after any change, addition or deletion of system components, or after any modification, repair or adjustment to system hardware or wiring. All components, circuits, system operations, or software functions known to be affected by a change must be 100% tested. In addition, to ensure that other operations are not inadvertently affected, at least 10% of initiating devices that are not directly affected by the change, up to a maximum of 50 devices, must also be tested and proper system operation verified. READ AND SAVE THESE INSTRUCTIONS. Follow the instructions in the installation, operating and programming manuals. These instructions must be followed to avoid damage to the control panel and associated equipment. Fire Alarm Control Panel (FACP) operation and reliability depend upon proper installation. DO NOT INSTALL ANY SIMPLEX PRODUCT THAT APPEARS DAMAGED. Upon unpacking your Simplex product, inspect the contents of the carton for shipping damage. If damage is apparent, immediately file a claim with the carrier and notify Simplex. ELECTRICAL HAZARD - Disconnect electrical power when making any internal adjustments or repairs. Servicing should be performed by qualified Simplex Representatives. RADIO FREQUENCY ENERGY - This equipment generates, uses, and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual, may cause interference to radio communications. It has been tested and found to comply with the limits for a Class A computing device pursuant to Subpart J of Part 15 of FCC Rules, which are designed to provide reasonable protection against such interference when operated in a commercial environment. Operation of this equipment in a residential area may cause interference in which case the user at his own expense will be required to take whatever measures may be required to correct the interference. Copyright and Trademarks Cautions and Warnings Technical Manuals Online! - http://www.tech-man.com

UL 864 Listings for Type of System: • UL 864 Power-Limited Fire Alarm Control Unit • Local (formerly NFPA 72A) Requires the sounding of an alarm via listed notification appliance(s) • Auxiliary (formerly NFPA 72B) Requires 4010-9809 City Circuit Module • Remote Station - protected premise (formerly NFPA 72C) Requires 4010-9809 City Circuit Module or the 4010-9810 or -9816 DACT • Proprietary - protected premise (formerly NFPA 72D) Requires 4010-9817 (with 4010-9818 or 4010-9819) or 4010-9821 Network Interface Modules • Central Station - protected premise (formerly NFPA 71) Requires 4010-9810 or -9816 DACT • Suppression Releasing Service Requires 4010-9814 Suppression Kit UL 864 Listings for Type of Service: • Automatic, Manual, Waterflow, and Sprinkler Supervisory UL 864 Listings for Type of Signaling: • Coded, Non-Coded, March-Time and DACT Requires the 4010-9810 or -9816 DACT Factory Mutual Approved: • Same as UL above Local Approvals: • CSFM* • MEA • City of Chicago (pending) Codes and Standards *This product has been approved by the California State Fire Marshal (CSFM) pursuant to Section 13144.1 of the California Health and Safety Code. See CSFM Listing No. 7170-0026:226 for allowable values and/or conditions for use concerning material presented in this document. Technical Manuals Online! - http://www.tech-man.com

any other applicable local codes and standards, when installing a fire alarm system. • NFPA 72 National Fire Alarm Code • NFPA 11 Standard for Low-Expansion Foam and Combined Agent Systems • NFPA 11A Standard for Medium- and High-Expansion Foam Systems • NFPA 12 Standard on Carbon Dioxide Extinguishing Systems • NFPA 12A Standard on Halon 1301 Fire Extinguishing Systems • NFPA 13 Standard for the Installation of Sprinkler Systems • NFPA 14 Standard for the Installation of Standpipe and Hose Systems • NFPA 15 Standard for Water Spray Fixed Systems for Fire Protection • NFPA 16 Standard for the Installation of Deluge Foam-Water Sprinkler and Foam-Water Spray Systems • NFPA 16A Standard for the Installation of Closed-Head Foam-Water Sprinkler Systems • NFPA 17 Standard for Dry Chemical Extinguishing Systems • NFPA 17A Standard for Wet Chemical Extinguishing Systems • NFPA 25 Standard for Inspection, Testing, and Maintenance of Water-Based Fire Protection Systems • NFPA 70 National Electrical Code • NFPA 80 Standard for Fire Doors and Fire Windows • NFPA 90A Standard for the Installation of Air Conditioning and Ventilation Systems • NFPA 90B Standard for the Installation of Warm Air Heating and Air Conditioning Systems • NFPA 92A Recommended Practice for Smoke-Control Systems • NFPA 92B Guide for Smoke Management Systems in Malls, Atria, and Large Areas • NFPA 101 Life Safety Code • NFPA 170 Standard for Fire Safety Symbols • NFPA 231C Standard for Rack Storage of Materials • NFPA 1221 Standard on the Installation, Maintenance, and Use of Public Fire Service Communication Systems The following conventions are used in this publication to identify special names or text. • When a membrane panel key (located below the display) is referenced in this manual, it is normally shown between left and right arrows. Examples are and . • Text enclosed in quotation marks indicates the title of a chapter or section of the manual, such as "About this Manual." • Bulleted lists, such as this one, provide you with information. They are also used to indicate alternatives in numbered procedural steps. • Numbered lists indicate procedures with steps that you must carry out sequentially. Codes and Standards (continued) About this Manual Technical Manuals Online! - http://www.tech-man.com

Introduction............................................................................................... 1-1 In this Chapter........................................................................................... 1-1 Related Documentation................................................................................. 1-2 Base System Module..................................................................................... 1-3 Overview................................................................................................... 1-3 SFI/O......................................................................................................... 1-3 Power Supply – Base System.................................................................... 1-4 Default Settings......................................................................................... 1-4 Environmental Specifications ................................................................... 1-4 Optional System Modules............................................................................. 1-5 Overview................................................................................................... 1-5 Optional Modules with Dedicated Hardware Slots................................... 1-5 Optional Modules for Expansion Slots ..................................................... 1-6 Remote Optional Modules ........................................................................ 1-7 Other Compatible Equipment.................................................................... 1-8 User Interface................................................................................................ 1-9 Overview................................................................................................... 1-9 Operator Key Definitions.......................................................................... 1-9 Menu Navigation Key Definitions .......................................................... 1-10 Passcodes, Access Levels, and Logging In and Out.................................... 1-12 Overview................................................................................................. 1-12 Passcodes and Access Levels.................................................................. 1-12 Logging In and Out................................................................................. 1-13 Menu Structure............................................................................................ 1-14 Chapter 2. Back Box Installation Overview................................................................................................... 2-1 In this Chapter........................................................................................... 2-1 Before You Begin ......................................................................................... 2-2 Unpacking the System............................................................................... 2-2 Installation Guidelines .............................................................................. 2-2 Standards and Codes................................................................................. 2-2 Remove Chassis and Cut Conduit Openings................................................. 2-3 Overview................................................................................................... 2-3 Step 1. Remove the Chassis ..................................................................... 2-3 Step 2. Cut Conduit Entrances ................................................................. 2-3 Mount the Backbox....................................................................................... 2-4 Surface Mounting the Back Box............................................................... 2-4 Semi-Flush Mounting the Back Box......................................................... 2-4 Re-install the Chassis.................................................................................... 2-5 Procedure.................................................................................................. 2-5 Table of Contents Technical Manuals Online! - http://www.tech-man.com

Overview................................................................................................... 3-1 In this Chapter........................................................................................... 3-1 Overview....................................................................................................... 3-2 Power Limited Versus Non-Power Limited Systems ................................ 3-2 Locations of Terminal Connections .......................................................... 3-3 NAC Wiring.................................................................................................. 3-4 Overview................................................................................................... 3-4 Terminal Connections............................................................................... 3-4 IDNet Wiring................................................................................................ 3-5 Overview................................................................................................... 3-5 Terminal Connections............................................................................... 3-5 AC Power and Battery Wiring ...................................................................... 3-6 AC Power.................................................................................................. 3-6 Installing and Connecting Batteries .......................................................... 3-7 Auxiliary Relays............................................................................................ 3-9 Auxiliary Relays........................................................................................ 3-9 System Power-Up and Checkout................................................................. 3-10 Connect AC & Battery Power................................................................. 3-10 Power-Up and Checkout ......................................................................... 3-10 Acceptance Test...................................................................................... 3-12 Periodic Testing and Maintenance.............................................................. 3-13 Overview................................................................................................. 3-13 Battery Testing Information.................................................................... 3-13 Chapter 4. Quick CFIG Overview................................................................................................... 4-1 Cautions and Warnings ............................................................................. 4-1 In this Chapter........................................................................................... 4-1 Reconfigure ALL Hardware.......................................................................... 4-2 Overview................................................................................................... 4-2 Procedure.................................................................................................. 4-2 Auto Detect NEW Hardware ........................................................................ 4-3 Overview................................................................................................... 4-3 Procedure.................................................................................................. 4-3 Restore Factory CFIG................................................................................... 4-4 Overview................................................................................................... 4-4 Procedure.................................................................................................. 4-4 Accept Default Settings for System Options................................................. 4-5 Procedure.................................................................................................. 4-5 Edit Settings for System Options .................................................................. 4-6 Overview................................................................................................... 4-6 Procedure.................................................................................................. 4-6 Save CFIG Option......................................................................................... 4-8 Overview................................................................................................... 4-8 Technical Manuals Online! - http://www.tech-man.com

Overview................................................................................................... 5-1 In this Chapter........................................................................................... 5-1 Card Addresses ............................................................................................. 5-2 Card Addresses ......................................................................................... 5-2 Adding, Deleting, or Modifying 4010 Cards ................................................ 5-3 Overview................................................................................................... 5-3 Adding a Card........................................................................................... 5-3 Deleting a Card ......................................................................................... 5-4 Modifying a Card...................................................................................... 5-5 Chapter 6. Configuring Points Overview................................................................................................... 6-1 In this Chapter........................................................................................... 6-1 Configure Points Menu ................................................................................. 6-2 Configuring Points Menu.......................................................................... 6-2 Configuring TrueAlarm Points...................................................................... 6-3 Overview................................................................................................... 6-3 Add IDNet Point ....................................................................................... 6-3 Edit TrueAlarm Point................................................................................ 6-3 Delete TrueAlarm Point............................................................................ 6-4 Configuring ZAM/IAM/RIAM Points .......................................................... 6-6 Overview................................................................................................... 6-6 Adding ZAM/IAM/RIAM Point ............................................................... 6-6 Editing a ZAM/IAM/RIAM Point............................................................. 6-6 Deleting ZAM/IAM/RIAM IDNet Point................................................... 6-8 Configuring Relay and NAC Points.............................................................. 6-9 Overview................................................................................................... 6-9 Procedure.................................................................................................. 6-9 Configuring Digital and Analog Pseudo Points .......................................... 6-11 Overview................................................................................................. 6-11 Configuring Digital Pseudo Points.......................................................... 6-11 Configuring Analog Pseudo Points......................................................... 6-12 Configuring 24-Point I/O Points ................................................................. 6-14 Overview................................................................................................. 6-14 Configuring 24-Point Input Points .......................................................... 6-14 Configuring 24-Point Output Points........................................................ 6-16 Configuring List Points............................................................................... 6-18 Overview................................................................................................. 6-18 Configure a List ...................................................................................... 6-18 Add a Point to a List ............................................................................... 6-19 Delete a Point from a List ....................................................................... 6-19 Delete ALL Points from a List................................................................ 6-20 Configuring User-Defined SW/LED........................................................... 6-21 Overview................................................................................................. 6-21 Configure a User-Defined Switch or LED .............................................. 6-21 Edit a Mode of a User-Defined SW/LED ............................................... 6-22 Technical Manuals Online! - http://www.tech-man.com

Overview................................................................................................... 7-1 In this Chapter........................................................................................... 7-1 System Options Menu................................................................................... 7-2 Introduction............................................................................................... 7-2 Time/Date Format......................................................................................... 7-3 Overview................................................................................................... 7-3 Setting the Time Format............................................................................ 7-3 Active Status Reminder................................................................................. 7-4 Overview................................................................................................... 7-4 Setting the Active Status Reminder........................................................... 7-4 Silence/Reset Inhibit ..................................................................................... 7-5 Overview................................................................................................... 7-5 Setting the Silence/Reset Inhibit ............................................................... 7-5 Alarm Cut-Out Timer.................................................................................... 7-6 Overview................................................................................................... 7-6 Setting the Alarm Cut-Out Timer.............................................................. 7-6 Door Drop on Alarm..................................................................................... 7-7 Overview................................................................................................... 7-7 Setting the Door Drop on Alarm Timer .................................................... 7-7 Door Drop on AC Loss................................................................................. 7-8 Overview................................................................................................... 7-8 Setting the Door Drop on AC Loss Timer ................................................ 7-8 Audible and Visible NAC Operation ............................................................ 7-9 Overview................................................................................................... 7-9 Setting the Audible or Visual NAC Operation.......................................... 7-9 TrueAlert Non-Addressable Horn Operation.............................................. 7-10 Introduction............................................................................................. 7-10 Setting the TrueAlert Non-Addressable Horn Option............................. 7-10 Depleted Battery Cut-Out ........................................................................... 7-11 Overview................................................................................................. 7-11 Setting the Depleted Battery Cut-Out ..................................................... 7-11 Stagger Start AHUs..................................................................................... 7-12 Overview................................................................................................. 7-12 Setting the Stagger Start AHU Delay Timer ........................................... 7-12 Enable City Circuit...................................................................................... 7-13 Overview................................................................................................. 7-13 Setting the Enable City Circuit Option.................................................... 7-13 Expansion Power ........................................................................................ 7-14 Overview................................................................................................. 7-14 Setting the Expansion Power Option....................................................... 7-14 Single-Station.............................................................................................. 7-15 Overview................................................................................................. 7-15 Enabling Single-Station .......................................................................... 7-15 Technical Manuals Online! - http://www.tech-man.com

Overview................................................................................................. 7-16 Example .................................................................................................. 7-16 Step 1. Turn ON Suppression Release ................................................... 7-17 Step 2. Assign Suppression Monitor Point Types to Suppression Release Monitor Points.............................................................. 7-17 Step 3. Create Suppression Release Monitor Lists................................. 7-17 Step 4. Assign Point Types to Suppression Outputs .............................. 7-18 Step 5. Create Suppression Release Output Lists................................... 7-18 Chapter 8. Custom Control Introduction............................................................................................... 8-1 In this Chapter........................................................................................... 8-1 Overview....................................................................................................... 8-2 Introduction............................................................................................... 8-2 SMPL Opcodes and Operators...................................................................... 8-3 Input Opcodes........................................................................................... 8-3 Input and Relational Operators ................................................................. 8-4 Output Opcodes ........................................................................................ 8-5 Custom Control Equation.............................................................................. 8-6 Custom Control Example.......................................................................... 8-6 Custom Control Programming ...................................................................... 8-7 To Start Custom Control Programming .................................................... 8-7 Custom Control Menu Navigation ............................................................ 8-8 Equation Level.......................................................................................... 8-9 Custom Control Level............................................................................... 8-9 Equations ................................................................................................ 8-10 Input Side (IF)......................................................................................... 8-10 Field 1 ..................................................................................................... 8-10 Field 2 ..................................................................................................... 8-15 Fields 3 & 4............................................................................................. 8-16 Output Side (THEN)............................................................................... 8-24 Application-Specific Examples................................................................... 8-26 Introduction............................................................................................. 8-26 Day Night Programming Example .......................................................... 8-26 TrueAlarm Heat Utility Monitoring Example......................................... 8-26 City Circuit Alarm-Output Programming Example................................. 8-26 AHJ City Circuit Reset Operation Example............................................ 8-27 Chapter 9. Saving a CFIG Introduction............................................................................................... 9-1 In this Chapter........................................................................................... 9-1 Viewing CFIG Properties.............................................................................. 9-2 Introduction............................................................................................... 9-2 Procedure.................................................................................................. 9-2 Continue, Restore CFIG, and Save CFIG ..................................................... 9-3 Continue.................................................................................................... 9-3 Restore CFIG ............................................................................................ 9-3 Save CFIG................................................................................................. 9-3 Technical Manuals Online! - http://www.tech-man.com

Overview................................................................................................. 10-1 Before Calling Tech Support .................................................................. 10-1 Diagnostics.................................................................................................. 10-2 Overview................................................................................................. 10-2 Running Diagnostics ............................................................................... 10-2 Diagnostic Options.................................................................................. 10-3 N2 Comm Diagnostics ............................................................................ 10-3 IDNet Diagnostics................................................................................... 10-3 IDNet Earth Fault Search Diagnostics .................................................... 10-4 Network Diagnostics............................................................................... 10-4 Walk Test.................................................................................................... 10-6 Overview................................................................................................. 10-6 Using Walk Test ..................................................................................... 10-6 TrueTest...................................................................................................... 10-8 Overview................................................................................................. 10-8 Using TrueTest ....................................................................................... 10-9 Crash Codes.............................................................................................. 10-10 Chapter 11. Operation Overview................................................................................................. 11-1 In this Chapter......................................................................................... 11-1 Handling Abnormal Conditions .................................................................. 11-2 Normal Operation ................................................................................... 11-2 Abnormal Conditions.............................................................................. 11-2 Acknowledging an Alarm, Trouble, or Supervisory Condition............... 11-3 Silencing Alarms..................................................................................... 11-3 Resetting the System............................................................................... 11-4 Viewing and Clearing Historical Logs........................................................ 11-5 Overview................................................................................................. 11-5 Using the Historical Logs........................................................................ 11-6 Viewing and Controlling Points.................................................................. 11-7 Overview................................................................................................. 11-7 Controlling/Viewing Points..................................................................... 11-7 How to Disable/Enable Points ................................................................ 11-9 How to Disable Points in Alarm ............................................................. 11-9 Editing Custom Labels.............................................................................. 11-10 How to Edit a Custom Label................................................................. 11-10 User Control Functions............................................................................. 11-12 Overview............................................................................................... 11-12 Using the Function Options................................................................... 11-12 Setting the Time and Date......................................................................... 11-14 Technical Manuals Online! - http://www.tech-man.com

Overview.................................................................................................. A-1 In this Chapter.......................................................................................... A-1 Hardware Device Types............................................................................... A-2 Overview.................................................................................................. A-2 TrueAlarm Hardware Device Types ........................................................ A-2 TrueAlarm Levels and Sensitivities ......................................................... A-3 Monitor Hardware Device Types............................................................. A-3 4009A Hardware Device Types............................................................... A-4 Software Point Types................................................................................... A-5 Monitor Point Types ................................................................................ A-5 Signal Point Types ................................................................................... A-6 Relay Point Types.................................................................................... A-7 TrueAlert Point Types.............................................................................. A-8 Appendix B. Hardware and Pseudo Points Overview.................................................................................................. B-1 In this Chapter.......................................................................................... B-1 Hardware Points........................................................................................... B-2 Introduction.............................................................................................. B-2 General Card Status Point Information .................................................... B-2 Master Controller Card ............................................................................ B-2 Master Controller Card Status Points....................................................... B-2 Master Controller Points.......................................................................... B-2 NAC Card ................................................................................................ B-3 NAC Card Status Points........................................................................... B-3 NAC Card Points ..................................................................................... B-4 Power Supply Card .................................................................................. B-5 Power Supply Card Status Points............................................................. B-5 Power Supply Points................................................................................ B-5 IDNet Card............................................................................................... B-6 IDNet Card Status Points......................................................................... B-6 IDNet Points ............................................................................................ B-7 RS232/Modem Card ................................................................................ B-8 RS232/Modem Card Status Points........................................................... B-8 RS232/Modem Points .............................................................................. B-8 DACT Card.............................................................................................. B-9 DACT Card Status Points ........................................................................ B-9 SDACT Points ......................................................................................... B-9 Network Card......................................................................................... B-10 Network Card Status Points ................................................................... B-10 Network Points....................................................................................... B-10 24I/O Card ............................................................................................. B-11 24I/O Card Status Points........................................................................ B-11 24I/O Points........................................................................................... B-12 LCD Card............................................................................................... B-12 LCD Card Status Points ......................................................................... B-12 LCD Points ............................................................................................ B-13 Pseudo Points............................................................................................. B-14 Introduction............................................................................................ B-14 Digital Pseudo Points............................................................................. B-14 4010 System Digital Pseudos................................................................. B-15 Technical Manuals Online! - http://www.tech-man.com

Analog Pseudo Points ............................................................................ B-18 4010 System Analog Pseudos ................................................................ B-18 4010 User Analog Pseudos .................................................................... B-18 List Pseudo Points.................................................................................. B-19 4010 System Lists .................................................................................. B-19 4010 User Lists ...................................................................................... B-20 Appendix C. Glossary of Terms Overview...................................................................................................C-1 Glossary ....................................................................................................C-1 Index ............................................................................... IN-1 Technical Manuals Online! - http://www.tech-man.com

(FACP) that monitors and controls up to 250 IDNet addressable devices. The Standard Function Input/Output (SFI/O) card, power supply, and cabinet provide a complete fire alarm control panel for most applications. Optional modules mount to the chassis to provide additional inputs and outputs, network communication, and additional power. Additionally, the 4010 can automatically control supplementary equipment such as fire doors and fans during an alarm condition using its auxiliary relay outputs. The 4010 provides audible and visible indications during trouble, supervisory, or alarm (fire) conditions. Should any of these conditions occur, the system activates the applicable notification appliance(s), LEDs, and the panel tone-alert. The indications continue until someone appropriately acknowledges the condition. This publication describes how to install, configure, operate, program, and test the Simplex 4010 Fire Alarm Control Panel (FACP). This chapter discusses the following topics: Topic See Page # Related Documentation 1-2 Base System Module 1-3 Optional System Modules 1-5 User Interface 1-9 Passcodes, Access Levels, and Logging In and Out 1-12 Menu Structure 1-14 Chapter 1 4010 FACP Overview Introduction In this Chapter Overview Technical Manuals Online! - http://www.tech-man.com

concerning field wiring, replacement parts, optional modules, and application information. Publication Title Part Number 4010-9806 Class A Module - Installation Instructions 574-055 4010-9809 City Circuit Card - Installation Instructions 574-056 4010 Fire Alarm Expansion Power Supplies Installation Instructions 574-057 4010 Fire Alarm RS232 Interface and Service Modem Cards Installation Instructions 574-058 4010-9820 Battery Meter Module - Installation Instructions 574-165 4010-9814 Suppression Kit - Installation Instructions 574-166 4010 Fire Alarm DACT Modules - Installation Instructions 574-167 4010 Fire Alarm 4120 Network Interface Cards Installation Instructions 574-168 4010 Fire Alarm - Parts List 574-424 4098 Detectors, Sensors, and Bases - Application Manual 574-709 4010 Fire Alarm - Field Wiring Diagrams 842-058 Related Documentation Technical Manuals Online! - http://www.tech-man.com

The SFI/O contains all connections for optional modules as well as N2 annunciator communication, IDNet, NAC, Auxiliary Power, Auxiliary Relay, PC Programmer (service port), and expansion power connections. The User Interface provides a 2x40 LCD screen, LEDs, operational and programming keys, all of which are visible with the cabinet door closed. See “User Interface,” later in this chapter for additional information about the user interface. TB6 TB7 TB1 TB3 TB4 P13 TB2 P14 TB8 TB5 Figure 1-1. 4010 SFI/O with User Interface Continued on next page Base System Module Overview SFI/O Overview Technical Manuals Online! - http://www.tech-man.com

• 24VDC (unregulated) 4A alarm power • 24VDC, 1/2 Amp auxiliary power • Battery Charger for 25Ah Batteries, 24-hour recharge at 120VAC (for larger battery capacity, use the 4081-9301, -9302, -9303, or -9304 External Battery Cabinet w/Charger) Note: The 4010 back box can accommodate up to 25Ah batteries. All switches and potentiometers are set at the factory before shipping. Although the settings should be accurate, you can change the settings on the following components as indicated. • LCD Adjustment (R143) – If necessary, use a small flat head screwdriver, turn the R143 Potentiometer located below TB1 to adjust the contrast on the LCD for the 4010. • Baud Rate Setting (SW2) - Baud rate settings for the 4010 communications are shown in Table 1-1 below. If you receive a communications trouble at the panel, verify that SW2 is set correctly. Table 1-1. SW2 Switch Settings Baud Rate SW2-1 SW2-2 OFF LINE ON ON 9,600 OFF ON 19,200 ON OFF 19,200 OFF OFF Important: You must set all cards to the same baud rate in order for the 4010 to operate properly. If you have a 4010 with a Network or DACT card, you must set the SW2 dip switch to the 9600 baud rate. It is recommended that you use the 19,200 option when uploading/downloading information to a PC. Temperature: The 4010 operates normally with ambient temperatures from 32° F to 120° F (0°C to 49°C), inclusive. Humidity: The 4010 operates normally under non-condensing humidity conditions up to 85% relative humidity @ 86° F (30°C). Base System Module, Continued Power Supply – Base System Default Settings Environmental Specifications Technical Manuals Online! - http://www.tech-man.com

instructions that accompany each module for more information. Those instructions and their part numbers are listed in the “Related Documentation” section of this chapter. Refer to the label inside the door of the 4010 for the placement of optional modules. Note: Certain modules are mutually exclusive. For example: • One DACT or One City Circuit Card is allowed. • One 4120 Network Card or One DACT is allowed. • One Dual RS232 Card or One RS232/Modem is allowed. • One Battery Meter Module or One 24VDC Extender Terminal Block. The 4010 has five dedicated mounting locations to support the following modules. 4010-9806 Class A Adapter Card for NACs The four NACs found on the SFI/O board are Class B (Style Y). To support Class A (Style Z) you must install an adapter card that mounts to the SFI/O board. Each adapter card supports two NACs. 4010-9809 City Circuit Card The city circuit card connects to the SFI/O with a ribbon harness to provide UL- listed connections to either Remote Station (reverse polarity) or Public Service Fire Communications Center (local energy) receiving units (selectable). The card has two circuits -- Circuit 1 reports only alarm events and Circuit 2 can be configured to report Trouble events or Trouble and Supervisory events. In the event of a CPU failure, a city card configured for a Trouble Output sends a trouble to the city circuit. The card is mounted to the right of the SFI/O at the top of the chassis. Newer versions of the 4010 FACP (Version 2.01 or later) provide the ability to reset the City Circuit in the following situation. • If the device(s) in alarm is physically removed. • No other devices are in an alarm state. • System Reset is performed. Enabling City Circuit reset is done via Custom Control. Refer to “Application- Specific Examples” at the end of Chapter 8 for specific information. Be sure to consult the AHJ before enabling the City Circuit Reset option. Continued on next page Optional System Modules Overview Optional Modules with Dedicated Hardware Slots Overview Technical Manuals Online! - http://www.tech-man.com

When more than 4A of Notification or AUX power is required, an expansion power supply may be added. The expansion power supply provides filtered 24VDC, 4A power for Notification and Auxiliary use. The expansion power supply is mounted to the right of the SFI/O at the bottom of the chassis. 4010-9814 Suppression Kit The 4010-9814 suppression kit consists of an expansion power supply designed to provide regulated 24VDC power for suppression circuits and a suppression system appliqué that is applied to the outside of the FACP. The suppression kit mounts in the same hardware slot as the expansion power supply. 4010-9820 Battery Meter Module The 4010-9820 Battery Meter Module provides an indication of the charge/discharge state of the FACP’s batteries (internal or external). The module also provides a constant reading of the current and voltage of the monitored batteries. This module mounts to the right of the city module. The 4010 has a maximum of two expansion slots available to support the following cards. 4010-9810 and -9816 DACT Cards. Two versions of the DACT are offered: 4010-9810  Event Reporting DACT - Five categories of status changes are supported with this card. The Central Station is notified of Alarm, Trouble, Supervisory or Waterflow status changes. AC Fail trouble is delayed for 6 to 12 hours before reporting to the Central Station. In the event of a CPU failure, the card sends a “CPU Trouble” message to the Central Station. 4010-9816  Per Point Reporting DACT - Specific information is available about which point in the system experiences a status change. The report sent to the Central Station includes the specific point address along with the point status. The DACT supervises the system CPU via N2 communication. In the event of a CPU failure, the DACT sends a “CPU Trouble” message to the Central Station. Continued on next page Optional System Modules, Continued Optional Modules with Dedicated Hardware Slots (continued) Optional Modules for Expansion Slots Technical Manuals Online! - http://www.tech-man.com

The Dual RS232 Card is connected to the N2 communication lines. The 4010 can vector messages to RS232 ports by category. The RS232 ports may be configured as follows: • Two serial printers (80 or 40 column). • One serial printer and one CRT/Keyboard (command line interface). The RS232 ports on the option card are electrically isolated from earth, allowing connection of an AC powered printer or CRT/keyboard. Note: Only the 80-column printer can be used to print 4010 system reports. 4010-9812 RS232/Service Modem Card This card is similar to the above dual RS232 card except that one port is a dedicated Service Modem port (command line interface). The second port may be programmed for use with a serial printer or left unused. Event vectoring by category is supported on the modem and RS232 ports. 4010-9817, -9818, -9819, and -9821 4120 Network Cards A 4120 Network card can be added to the 4010. This card communicates with the system CPU via N2 communication. The 4010 system can be a node on a 4120 Network, however it has limited functionality. Points on the 4010 may be declared as Public. No points on other nodes may be declared as External to the 4010. Set Host and Remote Download functions are fully supported. The following optional modules mount remotely from the 4010 FACP. 4606-9101 LCD Remote Annunciator The 4606 LCD annunciator for the 4010 provides remote area annunciation of the 4010 panel’s status. Pass-key protected, the user interface provides a 2x40 LCD screen, indicating LEDs, and operator membrane keys. 4605-8401 24-Point I/O The 24-Point I/O Card for the 4010 is capable of using any combination of 24 inputs or outputs to control LEDs, lamps, and relays, and to monitor contact closure inputs. The outputs can be ON continuous or flashed, at a slow or fast rate. Inputs may be unsupervised, supervised for opens, supervised for open and shorts, depending upon how the switch is wired externally. Continued on next page Optional System Modules, Continued Optional Modules for Expansion Slots (continued) Remote Optional Modules Overview Technical Manuals Online! - http://www.tech-man.com

meets the applicable agency listings for the intended use. • 4003 Voice Control Panel (VCP). Since the 4010 does not contain hardwired monitor points, the alarm/trouble output from the 4003 is connected to a Zone Adapter Module (ZAM). One of the NACs on the 4010 can be used to activate the 4003. • 4009A and 4009R IDNet NAC Extender. • The 4010 is compatible with the following 4098 smoke/heat sensors and bases: PID Description 4098-9710 Quickconnect, TrueAlarm, Photo Smoke Sensor 4098-9713 Quickconnect, TrueAlarm, Photo Smoke Sensor with sounder. 4098-9714 TrueAlarm, Photo Smoke Sensor (requires separate base) 4098-9717 TrueAlarm, Ion Smoke Sensor (requires separate base) 4098-9733 TrueAlarm Heat Sensor (requires separate base) 4098-9789, -9791 thru -9793 Sensor Bases • Power supplies that are power-limited and listed for fire-protective signaling use can be used with the 4010 when wired according to power-limited guidelines. • The 4010 is compatible with the 4120 network. In order to use the 4010 as a node on the network, you must have - 4100 master software must be Rev. 8.01 or higher and GCC/NPU must be Rev. 2.03 or higher. - 4120 network firmware must be Rev. 3.01 or greater. (Rev. 3.02.99 or later is recommended.) - 4010 network firmware must be Rev. 3.03.99 or later. Optional System Modules, Continued Other Compatible Equipment Technical Manuals Online! - http://www.tech-man.com

40-character backlit LCD, and a tone-alert mounted in the control panel. The purposes of the Operator and Menu keys are listed below. **SYSTEM IS NORMAL** 12:02:15pm Thur 04-Jul-96 Menu Function Disable Enable Exit Clear Enter Previous Next ALARM ACK FIRE ALARM SUPV ACK SYSTEM SUPERVISORY TROUBLE ACK SYSTEM TROUBLE ALARM SILENCE ALARM SILENCED SYSTEM RESET AC POWER User Programmed User Programmed User Programmed Figure 1-2. 4010 Operator Interface, Showing High-Level Status Screen The following information defines the operator (rectangular) keys on the 4010 panel. Alarm Acknowledge The key is used to acknowledge any unacknowledged fire alarms in the system and to scroll through the alarms in the active Alarm List. Supervisory Acknowledge The key is used to acknowledge any unacknowledged supervisories in the system and to scroll through the supervisory conditions in the active Supervisory List. Trouble Acknowledge The key is used to acknowledge any unacknowledged troubles in the system and to scroll through the troubles in the active Trouble List. Continued on next page User Interface Overview Operator Key Definitions TROUBLE ACK SUPV ACK ALARM ACK Operator Keys LEDs Menu Navigation Keys LCD SYSTEM IS NORMAL 10:09:33am Wed 27-Aug-97 Overview Technical Manuals Online! - http://www.tech-man.com

The key is used to silence any silenceable output types (generally all non-visible notification appliances). System Reset The key allows you to reset all alarm notification appliances and controls, remove alarms from the Alarm List, silence all silenceable outputs, reset detectors, and return the system to a normal state (provided that no alarms are present). The display will indicate that a reset is in progress and whether or not a reset completes successfully. The following information defines the menu navigation (round) keys on the 4010 panel. These keys perform access level dependent functions defined in the “Passcodes, Access Levels, and Logging In and Out” section of this chapter. Menu The key always brings you to the top of the main menu structure unless you are in Programming or Quick-CFIG menus (see the Menu Structure at the back of this chapter). Function The Function Menu is displayed when the key is pressed at the High-Level Status screen. Use the <� Previous> and <� Next> keys to scroll through the functions list. The function key provides access to commonly used control and display “functions,” and is also used for list editing. Disable/Enable The key allows the operator to quickly disable or enable any point that is currently displayed (passcode protected). A confirmation screen is displayed requesting be pressed before performing the actual enable or disable. Exit/Clear The key is used to back out of menus or displays to get to the top- level menu structure (refer to the “Menu Structure” at the end of this chapter). Where possible, the key will back out one level at a time. There are cases, however, that the key will return the operator directly to the top level. Continued on next page User Interface, Continued Operator Key Definitions (continued) Menu Navigation Key Definitions ALARM SILENCE SYSTEM RESET Menu Function Disable Enable Exit Clear Technical Manuals Online! - http://www.tech-man.com

additional information about the point shown on the display. In a programming screen, pressing indicates that the information on the display is correct and can be entered. The key is used in various other places within the menu structure, always for this same type of operation. Right <�> and Left Arrow <�> The <�> and <�> arrows are used in screens with multiple choices. The keys advance the focus (square brackets [ ] ) from field-to-field. Previous <� Previous> and Next <� Next> The <� Previous> and <� Next> keys allow you to move from screen-to- screen within any displayable object having multiple screens. This would include scrolling through an historical log, the point database, a list of points, or other similar activities. The <� Next> key selects the next display screen in sequence, and the <� Previous> key selects the previous screen. These keys are also used to view additional information about abnormal points or in viewing Historical Logs. User Interface, Continued Menu Navigation Key Definitions (continued) � Previous � Next � � Enter Overview Technical Manuals Online! - http://www.tech-man.com

This section describes logging in and out at specific access levels. All operations in the 4010 are protected at a preset level with designated passcodes to access these operations. The table below shows the basic operations and menu choices for specific access levels. The default passcodes are listed for Levels 2 through 4. Refer to the Menu Structure later in this chapter for a complete quick-reference of the main 4010 FACP menus. Table 1-2. Access Levels and Operations ACCESS LEVEL OPERATIONS 1 Ack Silence System Reset 2 Passcode = 2000 All Level 1 Operations, plus: Set Time/Date Point Control Enable/Disable Points 3 Passcode = 3000 All Level 1 & 2 Operations, plus: Clear Logs Clear Verification Tallies Programming - Edit/Clear Point Label - Restore/Save CFIG TrueTest Walk Test Reports 4 Passcode = 4000 All Level 1,2, & 3 Operations, plus: Quick CFIG Run Diagnostics Upload/Download Programming • Edit Cards • Edit SMPL Program • System Options Restart Panel • Warm Start • Cold Start Continued on next page Passcodes, Access Levels, and Logging In and Out Overview Passcodes and Access Levels Technical Manuals Online! - http://www.tech-man.com

the 4010 FACP using a passcode. After completing a task at a certain access level you should then Logout to return the access level to Level 1. When logged in at Level 2 or above and you do not press any front panel keys for more than ten minutes, the 4010 defaults to access level 1. All passcodes consist of a four-digit number. Logging in at a Level 4 causes a Service Mode trouble. Note that this trouble can only be cleared by restarting the panel. To Login, perform Steps 1 through 7 on a 4010 that is at the High-Level Status screen (refer to Figure 1-2 for an example of this screen). When moving from one digit to the next, an asterisk (∗) appears in the place of an entered number for security purposes. See Table 1-2 in the previous section for the default passcodes. 1. Obtain the appropriate passcode information for the appropriate level. 2. Press . 3. Press and hold <�NEXT> until [Login/Logout] is displayed, and then press . 4. Press and hold <�NEXT> until [Login] is displayed, and then press . 5. Press <�NEXT> to scroll through the numbers on the display until the appropriate number is displayed. 6. Press the right arrow <�> to move the focus brackets [ ] to the next digit in the passcode. Repeat Steps 5 & 6 until all numbers are entered. 7. When the passcode is correct, press to Login. A **Login Accepted** screen indicating your current access level is displayed briefly upon a successful Login attempt. If you did not enter the appropriate Login passcode, a **Login is Invalid** screen appears. To Logout, perform Steps 1 through 4 above except for Step 4 where you need to wait until [Logout] is displayed. Passcodes, Access Levels, and Logging In and Out, Continued Logging In and Out Overview Technical Manuals Online! - http://www.tech-man.com

backbox. This chapter discusses the following topics: Topic See Page # Before You Begin 2-2 Remove Chassis and Cut Conduit Openings 2-3 Mount the Backbox 2-4 Re-install the Chassis 2-5 Chapter 2 Back Box Installation Overview In this Chapter Back Box Installation Technical Manuals Online! - http://www.tech-man.com

• Carefully unpack the system and inspect for shipping damage. • Select a location for the control panel in a clean, dry, vibration-free area with moderate temperature (see the “Environmental Specifications” section in Chapter 1). Before installing the 4010, read the following guidelines: • Install the FACP in a readily accessible area with sufficient room to easily install and maintain the control panel. • Locate the top of the cabinet approximately five feet above the floor with the door hinge on the left-hand side. • Count the number of conductors needed for all devices and cut the appropriate knockouts. Pay careful attention to the routing for Power- Limited and Non-Power Limited wiring. You must maintain a 1/4-inch separation between these two types of wiring. All terminal connections are Power-Limited except those to the AC power, Battery, and City Circuit, and contacts when switching Non-Power Limited sources. • Review the precautions and warnings at the front of this publication. • All wiring must comply with the National and/or Local codes for fire alarm systems. All wiring must test free of grounds. • Leave sufficient room for batteries in the bottom of the back box (see the label inside the 4010 back box for more information). • Enclosure must be level and plumb when installed. When installing the 4010, you should be familiar with the following standards: • NEC Article 300 Wiring Methods • NEC Article 760 Fire Protective Signaling Systems • Applicable Local and State Building Codes • Requirements of the Local Authority Having Jurisdiction (AHJ) Before You Begin Unpacking the System Installation Guidelines Standards and Codes Technical Manuals Online! - http://www.tech-man.com

single piece electronics assembly that is shipped separately from the back box, retainer, and door. The system electronics (SFI/O and power supply) are mounted to a steel chassis. Refer to the 526-407 label inside the back box for additional information. Prior to installation you must remove the chassis containing the 4010 SFI/O and power supply from the back box. Use the following steps to remove the chassis. 1. Remove the door grounding wire from the back box. Remove the door from the hinges and set it aside. 2. Remove the metal retainer by gently lifting and pulling the bottom of the retainer out from the back box. Then, being careful not to drop the retainer, slide the top of the retainer out from under the lip of the top of the back box. 3. Remove the AC wiring Quick-Disconnect connector from the chassis by firmly squeezing the release tabs and pulling it free. The Quick-Disconnect connector is located directly below the chassis. Dress the wires so that they do not interfere with back box installation. 4. Loosen or remove the four mounting screws holding the chassis to the back box. 5. Lift the chassis out of the back box and store in a clean, dry, safe area for re- installation later. Determine the amount and proper location of conduit/service entrances. Make all appropriate entrances into back box (see Figure 2-1). Caution: Power-Limited and Non-Power-Limited wiring must enter through separate conduit/service entrances. AC power entrance into back box is recommended at the bottom right side of the back box. If a Bus Bar is required to terminate wire shields, see Figure 2-1 for proper mounting location. Entrances for shielded wire must be located within two inches of the bus bar. Maximum intrusion into box for conduit is 1/2-inch. Figure 2-1. Conduit and Bus Bar Mounting Locations. Remove Chassis and Cut Conduit Openings Overview Step 1. Remove the Chassis Step 2. Cut Conduit Entrances Back Box Installation TOP VIEW TYPICAL CONDUIT LOCATION 2" MAX IF USING BUS BAR BUS BAR MOUNTING STUDS Technical Manuals Online! - http://www.tech-man.com

you want to mount the back box (see the “Before You Begin” section of this chapter). 2. Using mounting hardware capable of supporting a fully loaded 4010 (approximately 50 lbs.), screw two screws into the wall where the top two teardrop holes of the back box are to be located. Tighten the screws leaving about a 1/8-inch gap from the seated position. 3. Carefully lift the back box and place the two teardrop holes over the mounting screws. 4. Screw two mounting screws into the two bottom back box holes and tighten all screws. 1. Remove the mounting knockouts from both sides of the back box. See Figure 2-2 for their location. 2. Make the appropriate opening in the wall or wall board to accommodate the back box. Dimensions of the backbox are 22” (55.8 cm) W x 18 (45.7 cm) H x 6 ¼ (15.8 cm) D. 3. Frame the opening to accommodate the back box. Fit the back box into the opening. Use wall stud guides to ensure free movement of the door. 4. Using mounting hardware capable of supporting a fully loaded 4010, screw or nail back box to the studs. Figure 2-2. Wall Stud Guides Continued on next page Mount the Backbox Surface Mounting the Back Box Semi-Flush Mounting the Back Box SIDE VIEW 5 3/8" 6 1/4" KNOCKOUT SCREW/NAIL HOLES (FOR SEMI FLUSH MOUNT.) WALL STUD GUIDES (1/2" WALL BD) WALL STUD GUIDES (5/8" WALL BD) DOOR FRONT OF STUD FOR 5/8" WALLBOARD FRONT OF STUD FOR 1/2" WALLBOARD Technical Manuals Online! - http://www.tech-man.com

power supply into the back box. 1. Insert two mounting screws into the top two mounting holes for the chassis. Tighten the screws leaving a 1/8-inch gap from the seated position. Caution: When mounting the chassis, pay careful attention to any wiring inside the back box. Do not crimp any wiring behind the chassis when mounting. 2. Carefully hang the chassis on the two top mounting screws using the top teardrop holes on the chassis. 3. Insert two mounting screws into the bottom two teardrop chassis mounting holes and tighten all screws. 4. Re-hang the door on the back box hinges and re-attach the door grounding wire to the back box. 5. You can re-install the retainer now before wiring or later after wiring is complete. Re-install the retainer by guiding the top lip of the retainer under the top lip of the back box and carefully sliding the bottom of the retainer into place. WARNING: DO NOT APPLY POWER TO THE 4010 AT THIS TIME! DO NOT connect the quick-disconnect AC connector to the chassis. Refer to the “Power-Up and Checkout” section of this publication for more information. Re-install the Chassis Procedure Back Box Installation Technical Manuals Online! - http://www.tech-man.com

This chapter describes how to wire the base 4010 FACP. Use the information in this chapter, the 526-407 and 526-408 labels located on the inside door of the FACP, and the 842-058 Field Wiring Diagram to wire the base panel. Refer to the publications listed in Chapter 1 to wire all optional modules. This chapter discusses the following topics: Topic See Page # Overview 3-2 NAC Wiring 3-4 IDNet Wiring 3-5 AC Power and Battery Wiring 3-6 Auxiliary Relays 3-9 System Power Up and Checkout 3-10 Periodic Testing and Maintenance 3-13 Chapter 3 Wiring Overview In this Chapter Wiring Technical Manuals Online! - http://www.tech-man.com

system. Adhere to the following guidelines and consult the NEC for specifics. • When installing the 4010 as a Power Limited system, you must observe the following guidelines: - Maintain ¼ inch of space between Power Limited wiring and AC Power or Battery wiring. - Run AC Power wiring in a separate conduit that enters the back box in the upper or lower right corner. - Route AC Power, battery wiring, city circuit connections, and non- Power Limited Relay wiring only through the shaded areas shown in Figure 3-1. Do not route Power Limited wiring through the shaded areas shown in the figure. • The 4010 FACP can be reclassified as a non-Power Limited system when installed in accordance with the latest version of NEC 760. In this case, all references to Power Limited must be removed from the panel’s labels. Figure 3-1. Location of Non-Power Limited Wiring Area Overview Power Limited Versus Non- Power Limited Systems FRONT VIEW 18" 22" BATTERY AREA NO CONDUIT ENTRY OR WIRING IN THIS AREA SHADED AREA IS FOR NON-POWER LIMITED WIRING ONLY AC TERMINAL BLOCK AC POWER HARNESS 8 1/2" DISCARD AFTER SHIPPING 14.5" Technical Manuals Online! - http://www.tech-man.com

components. Refer to the appropriate section later in this chapter for specific information on wiring a component. 4010-9813 Expansion Power Supply (565-792) or 4010-9814 Supression Power Supply (565-793) 4010-9809 City Module 4010-9820 Battery Meter Module 4010-9806 Class A Module (565-789) Pot for LCD Adjustment 4010-9806 Class A Module (565-789) WARNING: PTCs MUST NOT TOUCH EACH OTHER OR ANY OTHER METAL SURFACE! Figure 3-2. Base Panel Wiring Overview, Continued Locations of Terminal Connections Wiring Technical Manuals Online! - http://www.tech-man.com

strobes. These NACs are standard Class B (Style Y). Optional Class A (Style Z) operation can be achieved using an adapter. Refer to the 4010-9806 Class A Module - Installation Instructions, Part No. 574-055 for information on the Class A NAC adapter. The NACs supervise for short or open circuit troubles. In the event of a short, the NAC does not energize. Each NAC is rated at 2A. Up to 4A of NAC power is available from the base unit. If more power is needed, NAC 3 and NAC 4 can be connected to an expansion power supply. An auxiliary (AUX) power connection (rated at 1/2A, 24VDC) is provided at TB5 located to the left of the auxiliary (AUX) relay terminal blocks at the bottom center of the SFI/O. Current drawn from TB5 must be deducted from the 4A total NAC power. Each NAC can be configured as “On until Silence” or “On until Reset” and can be coded or non-coded (refer to “Chapter 6 - Configuring Points” for more information). The 4010 can disconnect each NAC individually to aid in locating earth faults. The NAC’s wiring connects to TB1 and TB2 as shown in Figure 3-3. These terminal blocks are barrier strip type that can accommodate 12-18 AWG wires. TB1 and TB2 are located in the upper left corner of the SFI/O. Refer to the 842- 058 wiring diagram for Alarm Current, Wiring Distance, and Line Resistance values. TB1-1: NAC 1 + Alarm TB1-2: NAC 1 - Alarm TB1-3: NAC 2 + Alarm TB1-4: NAC 2 - Alarm TB2-1: NAC 3 + Alarm TB2-2: NAC 3 - Alarm TB2-3: NAC 4 + Alarm TB2-4: NAC 4 - Alarm Figure 3-3. NAC Wiring NAC Wiring Overview Terminal Connections NAC 1 NAC 2 NAC 3 NAC 4 TB1 TB2 1 2 3 4 Alm+ Alm- Alm+ Alm- 1 2 3 4 Alm+ Alm- Alm+ Alm- Technical Manuals Online! - http://www.tech-man.com

pull stations, 4009 IDNet NAC Extender, etc.). The 4010 supports 250 devices on a single pair of wires on a single channel. The IDNet channel supports Style 4 and 6 as part of the base system. Refer to the 4010 Field Wiring Diagram (842-058) for all wiring information. IDNet communication also supports the detection of duplicate devices. IDNet detects if two devices are set to the same address. This function is activated from the front panel (see IDNet Diagnostics in the Diagnostic/Troubleshooting section of this publication). Use the information below to wire the IDNet communication lines (14-18 AWG) to TB4 located in the upper right corner of the SFI/O. • To connect Class A wiring, wire the “B” terminals (TB4-1 and -2) to each device in succession without T-taps (observe polarity). At the last device in the loop, return the B+ wire to the A+ terminal (TB4-4) and the B- wire to the A- terminal (TB4-5). • To connect Class B wiring, jumper B+ to A+ and B- to A- using 14-18 AWG insulated wire (T-taps are allowed). Connect B+ to all devices (positive connection) and connect B- to all devices (negative connection). Figure 3-4. IDNet Connections IDNet Wiring Overview Terminal Connections TB4 6 5 4 3 2 1 IDNet Comms A- A+ SHLD B- B+ Wiring Technical Manuals Online! - http://www.tech-man.com

must be run in a separate conduit, and should enter the back box in the lower right corner. Use the shaded area of Figure 3-5 only for routing of AC power wiring. All wiring must be neatly dressed within the back box. Use the wiring guides inside the back box when possible. • The FACP requires connection to a separate dedicated AC fire alarm circuit, which must be labeled “Fire Alarm.” • The AC power circuit must connect to the line side of the main power feed of the protected premises. • No other equipment can be powered from the fire alarm circuit. • The AC power circuit wiring must run continuously, without any disconnect devices, from the power source to the FACP. • Over-current protection for this circuit must comply with Article 760 of the National Electric Code as well as local codes. • Use 12AWG wire with 600-volt insulation for this circuit. 14.5" BATTERY AREA NO CONDUIT ENTRY OR WIRING IN THIS AREA WIRE GUIDES SHADED AREA IS FOR NON-POWER LIMITED WIRING ONLY AC TERMINAL BLOCK AC POWER HARNESS Figure 3-5. AC Power Wiring Continued on next page AC Power and Battery Wiring AC Power 1. Match incoming Neutral and Hot wires to their corresponding wires leading from the terminal block located in the lower right corner of the back box to the Quick-Disconnect harness and screw into place. 2. The safety ground wire from the AC source must be connected to the ground stud located below the terminal block. Do the following to connect the ground wire to the stud: a) Run the ground wire to the stud and cut it, leaving a little slack for adjustment. b) Crimp a spade terminal (Part No. 474-144 or -015) onto the ground wire. c) Place a lock washer on the stud, followed by the terminal and then another lock washer. d) Securely fashion a nut (Part No. 322-128) onto the stud. Technical Manuals Online! - http://www.tech-man.com

batteries. The following is a list of compatible batteries. • 2081-9272, 6.2 Ah • 2081-9274, 10 Ah • 2081-9275, 18 Ah • 2081-9288, 12.7 Ah • 2081-9287, 25 Ah Install the batteries in the area shown on the label located in the bottom of the back box. Use the following steps, Part No. 733-945 battery harness (733-903 for Canadian systems), and Figure 3-6 to connect the batteries to TB8 located in the lower left corner of the SFI/O. Domestic systems should use the following procedure. 1. Using the short white wire crimped at both ends, jumper one positive (+) terminal of one battery to the negative (-) terminal of the other battery. 2. Take the non-crimped end of the red wire from the harness and connect this to the + side of TB8. Connect the Fast-on connector on the other end of the Red wire to the Positive terminal of one of the batteries. 3. Take the non-crimped end of the black wire from the harness and connect this to the - side of TB8. Connect the Fast-on connector on the other end of the Black wire to the Negative terminal of one of the batteries. Figure 3-6. Battery Connections – Domestic System Canadian systems should use Figure 3-7 as an installation guide. WARNING: DO NOT APPLY BATTERY POWER TO THE 4010 AT THIS TIME! DO NOT connect crimped ends of the red and black wires to the battery. Refer to the “Power-Up and Checkout” section of this publication for more information. Continued on next page AC Power and Battery Wiring, Continued Installing and Connecting Batteries − BATTERY + TB8 Wiring Technical Manuals Online! - http://www.tech-man.com

565-738 P4 RED RELAY 5 3 1 6 4 2 BLK RED RED CANADIAN LOW BATTERY MODULE TB8 BATTERY HARNESS 733-903 BATTERY BATTERY Figure 3-7. Canadian Battery Wiring WARNING: DO NOT APPLY BATTERY POWER TO THE 4010 AT THIS TIME! DO NOT connect crimped ends of the red and black wires to the battery. Refer to the “Power-Up and Checkout” section of this publication for more information. AC Power and Battery Wiring, Continued Installing and Connecting Batteries (continued) Technical Manuals Online! - http://www.tech-man.com

and the other at TB7. Each circuit provides one form “C” contact (normally open or normally closed) rated at 2A (24VDC), or 0.5A (120 VAC) with optional 120 Volt auxiliary relay kit. The default operation for AUX1 is an Alarm Relay and AUX2 is a Trouble Relay. The AUX relay circuits can also be programmed for other desired operations using the front panel (see “Chapter 6 - Configuring Points”). Use Figure 3-8 to wire the AUX relay circuits. TB6 and TB7 are located at the bottom of the SFI/O near the center. When power for the AUX relay contacts is from TB5 (AUX Power), 4010-9813, or 4010-9814 expansion power supplies, the circuit is power-limited. When power for the AUX relay contacts IS NOT from the sources listed above, use an in-line fuse (Part No. 208-165). If power source is non-power-limited, wiring must be routed through the non-power-limited spaces shown in Figure 3-1 and “power-limited” markings must be obliterated. Figure 3-8. AUX Relay Connections Auxiliary Relays Auxiliary Relays Bottom of the SFI/O TB6 TB7 NO C NC AUX1 AUX2 NC C NO Wiring Technical Manuals Online! - http://www.tech-man.com

1. Re-connect the AC power harness removed in previous steps 2. Connect the crimped ends of the 733-945 battery harness (733-903 for Canadian systems) to the batteries. Observe polarity (red to +, black to -) when connecting batteries. WARNING: Battery contains sulfuric acid which can cause severe burns to the skin and eyes, and can destroy fabrics. Replace any leaking or damaged battery. If contact is made with sulfuric acid, immediately flush skin or eyes with water for 15 minutes and seek immediate medical attention. Caution: Notify fire, central station, and/or building personnel before testing the system. Power-Up After applying power to the system, use the following list to check the 4010 for proper operation. • Check that the green AC Power LED is ON. • Check that all yellow and red LEDs are OFF. • Use the Lamp Test procedure in “Chapter 11 - Operation” of this publication to verify that all 4010 LEDs and LCD segments work properly. On power-up, the 4010 performs the following: • Displays revision of boot-loader software • Self Test - CPU Hardware Checkout • Linkscan - Checking for a Programmer Unit Connection • Memory Scan - Checking for Incorrect Application • Start up - 4010 FACP Startup Figure 3-9. 4010 Start Up Screen Continued on next page System Power-Up and Checkout Connect AC & Battery Power Power-Up and Checkout Start up Technical Manuals Online! - http://www.tech-man.com

the High-Level Status screen shown in Figure 3-10 displays. If troubles exist in the system, Figure 3-11 displays after pressing . Note: The High-Level Status screen is the first screen shown on a 4010 whether in a normal or a trouble/supervisory/fire alarm state before any keys are pressed. Figure 3-10. System Normal (High Level Status) Screen Figure 3-11. System Trouble Screen Note: If the self-test fails, the 4010 displays the error code and waits 45 seconds before attempting a restart. Refer to Chapter 10 for a list of error codes. Checkout Caution: Before proceeding with the acceptance test procedures, do the following: • Notify the fire department and the central alarm receiving station if transmitting alarm conditions. • Notify building personnel of the test so that alarm sounding devices are disregarded during the test session. • When necessary, disable activation of alarm notification appliances and speakers to prevent their sounding. Continued on next page System Power-Up and Checkout, Continued Power-Up and Checkout (continued) SYSTEM IS NORMAL 10:09:33am Wed 27-Aug-97 FIRE=0 SUPERVISORY=0 TROUBLE=3 [TrueAlarm] Add 1/130 FIRST FLOOR EAST WING ROOM 12 Smoke Detector Trouble 1/3 Custom Label Point Type First of Three Troubles Device Condition Wiring Technical Manuals Online! - http://www.tech-man.com

complete operational test on the entire installation to verify compliance with applicable NFPA standards. Testing should be conducted by a Simplex-trained technical representative in the presence of a representative of the Authority Having Jurisdiction, and the customer’s representative. Follow the procedures outlined in Chapter 7 “Inspection, Testing, and Maintenance” of NFPA Standard 72-1996 and the following steps. 1. Activate an initiating device (smoke, pull, etc.) and check that all active notification appliances (strobes, horns, etc.) function. Reset the alarm initiating device, the FACP, and any other associated equipment. Repeat this step for each initiating device. 2. Remove AC power, activate an initiating device, and check that active notification appliances sound, and alarm indicators illuminate. Measure the battery voltage with notification appliances active. Replace any battery with a voltage of less than 24VDC and reapply AC power. Note: Step 2 requires fully charged batteries. If batteries are new or discharged due to a recent power outage, allow the batteries to charge for 48 hours before testing. Refer to “Periodic Testing and Maintenance” section for more information on testing batteries. 3. Reapply AC power and check that all yellow and red LEDs are OFF and the green AC Power LED is ON. Caution: Notify fire, central station, and/or building personnel when you finish testing the system. System Power-Up and Checkout, Continued Acceptance Test Technical Manuals Online! - http://www.tech-man.com

devices, and any other associated equipment is essential to ensure proper and reliable operation. Test and maintain the FACP according to the schedules and procedures outlined in the following publications: • NFPA Standard 72-1996, Chapter 7, “Inspection, Testing, and Maintenance.” • Installation Instructions for the peripheral devices installed in your system. Correct any trouble condition or malfunction immediately. Periodic testing and maintenance of the system batteries must be done to ensure proper and reliable back-up operation. Test and maintain the system batteries using the following information. All sealed lead-acid batteries in fire alarm service should be tested annually. Replace all sealed lead-acid batteries that have been in service for four or more years. It is recommended that a battery tester made specifically for checking sealed lead-acid batteries be used. Such a tester is available under Service Part No. 553-602. If a battery tester is unavailable, the “voltage response test” described in the following information can be used to detect batteries with very low capacity or shorted cells. Caution: A defective battery charger circuit can cause battery failure. Check the condition of the battery charger when either a battery tester or a voltage response test reveals weakened batteries. Voltage Response Test 1. Disconnect battery from system. 2. Connect a digital voltmeter across the battery. 3. Connect the appropriate sized resistor(s) (see Table 3-1) across the battery’s terminals for the listed test time. Caution: Resistors will get hot during test! Use 12AWG wire for battery-to-resistor hookup. 4. Record the end voltage reading. 5. Treat the battery as described in Table 3-2. Continued on next page Periodic Testing and Maintenance Overview Battery Testing Information Wiring Technical Manuals Online! - http://www.tech-man.com

Voltage Amp Hr Resistor (Ohms) Watts Part No. and Description Test Time 12 6.2 6.0 50 380-031 2 Seconds 12 8 4.5 50 380-031 (adj to 4.5 Ohm) 2 Seconds 12 10 4.0 50 380-031 (adj to 4 Ohm) 2 Seconds 12 18 2.0 100 380-031 (3 in parallel) 2 Seconds 12 25 1.5 100 382-090 (2 in parallel) 2 Seconds 12 33 1.0 150 382-090 (3 in parallel) 2 Seconds 6* 50 1.0 150 382-090 (3 in parallel) 4 Seconds 12 110 1.0 150 382-090 (3 in parallel) 4 Seconds *Test 2 batteries in series for 12V Table 3-2. Battery Readings and Instructions If end voltage reading of battery is: Instructions 11.8V or more Put in Service 11.7V to 11.0V Charge Battery* 10.9V or less Discard Battery *Retest battery after charging Discard battery after four or more years of service. Dispose of according to manufacturer’s guidelines. Periodic Testing and Maintenance, Continued Battery Testing Information (continued) Technical Manuals Online! - http://www.tech-man.com

automatically program the components and features of the 4010. Quick CFIG is especially useful for programming basic system components following a new installation, and for adding components to an existing installation. Quick CFIG functions include the following: • Reconfigure All Hardware • Autodetect all new hardware added since CFIG was last saved • Restore the Factory CFIG • Accept default settings for system options • Edit settings of system options Be alert to the following when using Quick CFIG: • WARNING: The 4010 System will NOT continue to operate as a Fire Alarm System during the programming of Quick CFIG operations. • Quick CFIG performs an IDNet duplicate address search, and terminates if duplicate addresses are found. • Using the Quick CFIG options changes the 4010 configuration. When changing the configuration, information could be lost. • Quick CFIG is not allowed if a DACT or Network card is installed. Use Quick CFIG first, and then program the DACT or network card. • Class A Adapters are not automatically detected by Quick CFIG. Refer to Chapter 6 for information on programming a Class A NAC. • TrueAlert Non-Addressable functions are not accessible through Quick CFIG. You must manually program the appropriate NACs with the TrueAlert point type to enable TrueAlert operation. Refer to Chapter 6 for information on manually programming a NAC’s point type. • Quick CFIG automatically configures the hardware device type for a 4009 (4009A, R4009A, 4009A8, R4009A8). All 4009 NACs are set for Class B operation and assigned a point type of SSIGNAL. This chapter discusses the following topics: Topic See Page # Reconfigure All Hardware 4-2 Auto Detect New Hardware 4-3 Restore Factory CFIG 4-4 Accept Default Settings for System Options 4-5 Edit Settings for System Options 4-6 Chapter 4 Quick CFIG Overview Cautions and Warnings In this Chapter Programming Technical Manuals Online! - http://www.tech-man.com

exists and this option is selected, it clears the current configuration and adds all currently connected devices to the CFIG. 1. Press . 2. Press or until [Quick CFIG] is displayed and then press . A warning appears, indicating that the 4010 is no longer in the Fire Alarm Operation mode. 3. Press to continue with the Quick-CFIG option. 4. Press or until is displayed and then press . A warning appears, indicating that this will delete the current configuration. 5. Press to continue. Another warning appears, indicating that you need to press to confirm the deletion. A message appears indicating that Quick CFIG is reconfiguring the hardware. This message is followed by another, which indicates that Quick CFIG is scanning for IDNET devices. The Reconfigure ALL Hardware function is complete when a message similar to the following appears. Refer to “Save CFIG Option” at the end of this chapter for information on saving the CFIG once you have reconfigured the hardware. Reconfigure ALL Hardware Overview Procedure Please Wait . . . Fire Alarm Operation Suspended WARNING to Continue WARNING This will DELETE current configuration WARNING to Continue WARNING Press to confirm deletion ** Automatic Hardware Detection Completed ** Total IDNet Devices Added: 128 Technical Manuals Online! - http://www.tech-man.com

hardware and programming remains the same. 1. Press . 2. Press or until [Quick CFIG] is displayed and then press . A warning appears, indicating that the 4010 is no longer in the Fire Alarm Operation mode. 3. Press to continue with the Quick-CFIG option. 4. Press or until is displayed and then press . A warning appears, indicating that this will change the current configuration. 5. Press to continue. Another warning appears, indicating that you need to press to confirm the hardware detection operation. A message appears indicating that Quick CFIG is reconfiguring the hardware. This message is followed by another, which indicates that Quick CFIG is scanning for IDNET devices. The Auto Detect NEW Hardware function is complete when a message similar to the following appears. Refer to “Save CFIG Option” at the end of this chapter for information on saving the CFIG once you have reconfigured the hardware. Auto Detect NEW Hardware Overview Procedure Please Wait . . . Fire Alarm Operation Suspended WARNING to Continue WARNING This will CHANGE current configuration WARNING to Continue WARNING Press to confirm Detect NEW ** Automatic Hardware Detection Completed ** Total IDNet Devices Added: 128 Programming Technical Manuals Online! - http://www.tech-man.com

points (Analog and Digital) are cleared, Custom Control is erased, etc. 1. Press . 2. Press or until [Quick CFIG] is displayed and then press . A warning appears, indicating that the 4010 is no longer in the Fire Alarm Operation mode. 3. Press to continue with the Quick-CFIG option. 4. Press or until is displayed and then press . A warning appears, indicating that this will delete the current configuration. 5. Press to continue. The following message appears, indicating that the system is restoring the factory default configuration. This message is followed by a series of internal test messages. The High-Level Status screen appears when the operation is complete. Restore Factory CFIG Overview Procedure Please Wait . . . Fire Alarm Operation Suspended WARNING to Continue WARNING This will DELETE current configuration ** Restoring Factory Default Panel ** Technical Manuals Online! - http://www.tech-man.com

2. Press or until [Quick CFIG] is displayed and then press . A warning appears, indicating that the that the 4010 is no longer in the Fire Alarm Operation mode. 3. Press to continue with the Quick-CFIG option. 4. Press or until is displayed and then press . A warning appears, indicating that this operation may change current settings. 5. Press to continue. The following message appears, indicating that the system is restoring the default settings for system options. Accept Default Settings for System Options Procedure Please Wait . . . Fire Alarm Operation Suspended WARNING to Continue WARNING This may CHANGE current setting ** Default Settings Restored ** Programming Technical Manuals Online! - http://www.tech-man.com

options by scrolling through the choices shown in Table 4-1 and selecting the appropriate settings for each. For timer options, selecting “0”initiates the action immediately. 1. Press . 2. Press or until [Quick CFIG] is displayed and then press . A warning appears, indicating that the 4010 is no longer in the Fire Alarm Operation mode. 3. Press to continue with the Quick-CFIG option. 4. Press or until is displayed and then press . 5. Use the and keys to scroll through the system options. Edit each of the system options as necessary, using the information in Table 4-1. Refer to Chapter 7 for specific information on system options. Table 4-1. System Options and Available Settings System Option Settings Time/Date Format Choose 12 or 24-Hour Format Active Status Reminder Choose: • On/Off; default Off • Set Reminder Interval (1-12 Hours); default = 8 • Signal Duration (0-60 Secs.) 0=ON til clear default = 5 Alarm Silence/Reset Inhibit Choose a timer range from 0 - 60 Mins; default = 0 Alarm Cut-out Timer Choose a timer range from 0 - 60 Mins; default = 0 Door Drop on Alarm Choose a timer range from 0 - 60 Secs; default = 0 Door Drop on AC Power Loss Choose a timer range from 0 - 60 Mins; default = 0 Audible NAC Operation Choose: • Audible NACs: Steady • Audible NACs: Slow March • Audible NACs: Fast March • Audible NACs: Temporal (default) Continued on next page Edit Settings for System Options Overview Procedure Please Wait . . . Fire Alarm Operation Suspended Technical Manuals Online! - http://www.tech-man.com

System Option Settings Visual NAC Operation Choose: • Visual NACs: Steady • Visual NACs: Slow March • Visual NACs: Fast March • Visual NACs: Temporal • Visual NACs: Synchronous (default) TrueAlert Non-Addressable NAC Horn Operation Choose: • Temporal (default) • Steady • Slow March Depleted Battery Cutout Choose ON or OFF; default = OFF. Note: Set Depleted Battery Cutout to ON for suppression release systems. Stagger Start AHU Choose a timer range from 0 - 60 Secs; default = 30 Enable City Circuit Choose ON or OFF; default = OFF Expansion Power Choose ON or OFF; default = OFF Suppression Release (refer to “Chapter 7 - System Options” for more information) Choose: • ON or OFF (default = OFF) • Dual Detector (default = OFF) • Detector Delay (default = 60) • Manual Delay (default = 30) Edit Passcodes* Change Passcode Designations Logical Zone Labels* Apply Zone Labels *Available under Quick-CFIG System Options Menu Only. Edit Settings for System Options, Continued Procedure (continued) Programming Technical Manuals Online! - http://www.tech-man.com

changing hardware and point types, etc.), you may want to save the CFIG following the Quick CFIG operation. The Save CFIG option saves all information to the 4010 configuration after or during programming. Choose this option if you wish to save all of your edits and modifications you made during your programming session to the 4010 configuration. You can Save CFIG by choosing the menu option or pressing Exit/Clear to back out of Programming mode and then choosing the Save CFIG option from the 4010 prompts. When exiting the programming mode, your 4010 re-boots and becomes operational as a fire alarm system. Save CFIG Option Overview Technical Manuals Online! - http://www.tech-man.com

chapter describes how to add, delete, or modify optional cards in the 4010 FACP. Note: The system must be powered down before cards are added to the system. This chapter discusses the following topics: Topic See Page # Card Addresses 5-2 Adding, Deleting, or Modifying 4010 Cards 5-3 Chapter 5 Configuring Cards Overview In this Chapter Programming Technical Manuals Online! - http://www.tech-man.com

Table 5-1. 4010 Card Addresses Card Address Reserved Cards 0 CPU Board 1 NAC/Relay circuits 2 Power Supply 3 IDNet Channel 4 Dual RS232 or Service Modem 5 - 7 Unused 8 4120 Network or DACT cards 9 - 14 N2 Slaves (24-Point I/O or LCD Annunciator) 15 - 16 Unused 17 4009 IDNet NAC Extender 18 System Digital Pseudo Points 19 User Digital Pseudo Points 20 System Analog Pseudo Points 21 User Analog Pseudo Points 22 System List Pseudo Points 23 User List Pseudo Points Card Addresses Card Addresses Technical Manuals Online! - http://www.tech-man.com

aware of the following configuration rules when adding, deleting, or modifying cards. • Cards 1 through 3 and 17 through 23 cannot be deleted. • Certain cards are mutually exclusive. For example: - One 4120 Network Card or One DACT is allowed. - One Dual RS232 Card or One RS232/Modem is allowed. • The City Circuit card and Expansion Power Supply are enabled via the System Options menu. Refer to Chapter 7 for information on doing this. • The DACT and Network cards are programmed and added to the 4010 FACP via the 4010 PC Programming tool. Use the following steps to add a card to the 4010 FACP. 1. Press . 2. Press or until [PROGRAMMING] is displayed and then press . A warning appears, indicating that the 4010 is no longer in the Fire Alarm Operation mode. 3. Press to continue. 4. Press or until is displayed and then press . 5. Press or until is displayed. 6. Press or to scroll through the choices listed below. • RS232 Card (Card Address 4) • Modem Card (Card Address 4) • 24IO Card (Card Address 9 through 14) • LCD (Card Address 9 through 14) 7. Once the desired card is displayed, press Enter. The RS232 and Modem cards are automatically set to card address 4. Follow the prompts to confirm this action. Continued on next page Adding, Deleting, or Modifying 4010 Cards Overview Adding a Card Please Wait . . . Fire Alarm Operation Suspended Programming Technical Manuals Online! - http://www.tech-man.com

must choose an available address of 9 through 14. (The system automatically picks the next available address.) When selecting 24IO or LCD and then pressing Enter, the following figure appears. 9. Press or to scroll through the available addresses, select the appropriate address for your card, and then press Enter. Follow the prompts to confirm this action. Use the following steps to delete a card from the 4010 FACP. 1. Press . 2. Press or until [PROGRAMMING] is displayed and then press . A warning appears, indicating that the 4010 is no longer in the Fire Alarm Operation mode. 3. Press to continue. 4. Press or until is displayed and then press . Caution: Deleting 4010 Cards also deletes any modes and SMPL (Custom Control) programming associated with that card. 5. After selecting Delete a 4010 Card as your option under the Configure Cards menu, press or to scroll through the cards configured in the 4010 FACP. 6. When the card you wish to delete is displayed, press Enter. 7. Follow the prompts to confirm this action. Continued on next page Adding, Deleting, or Modifying 4010 Cards, Continued Adding a Card (continued) Deleting a Card Card=[09] Card Type=LCD Card Please Wait . . . Fire Alarm Operation Suspended Technical Manuals Online! - http://www.tech-man.com

can modify from this menu are the Dual RS232, Modem/RS232, and LCD Annunciator cards. 1. Press . 2. Press or until [PROGRAMMING] is displayed and then press . A warning appears, indicating that the 4010 is no longer in the Fire Alarm Operation mode. 3. Press to continue. 4. Press or until is displayed and then press . 5. Press or until is displayed. 6. Press or to scroll through the cards configured in the 4010 FACP. 7. When the card you wish to modify is displayed, press Enter. The available modifications you can make per card are shown in Table 5-2. The 4010 prompts you on which keys to press to execute different options. Continued on next page Adding, Deleting, or Modifying 4010 Cards, Continued Modifying a Card Programming Please Wait . . . Fire Alarm Operation Suspended Technical Manuals Online! - http://www.tech-man.com

4010 Card Modifications RS232 Card Port A and Port B Device: PRT40U (unsupervised 40-Column printer) PRT40S (supervised 40-Column printer PRT80U (unsupervised 80-Column printer) PRT80S (supervised 80-Column printer) UNUSED COMMAND (For use with a CRT on Port B Only) Baud Rates: 1200, 2400, 4800, 9600, 19200, 38400 Parity: NONE, EVEN, ODD Note: To print 4010 reports, you must have an 80-column printer. Modem Card Port A and Port B Device: PRT40U (unsupervised 40-Column printer) PRT40S (supervised 40-Column printer PRT80U (unsupervised 80-Column printer) PRT80S (supervised 80-Column printer) UNUSED COMMAND (For use with a CRT on Port B Only) Baud Rates: 1200, 2400, 4800, 9600, 19200, 38400 Parity: NONE, EVEN, ODD LCD Card Enter selects ALL events to report to the LCD, Default Key Operation, and Default Overrides. Pressing Next allows you to choose Yes or No for the following: EVENTS: Fire, Supervisory, Trouble, Reset/Silence, Test, CCE Print Events KEY OPERATION: Fire Ack, Supv Ack, Trouble Ack, System Reset, Alarm Silence OVERRIDE ON ALARM: Fire Ack, Supv Ack, Trouble Ack, System Reset, Alarm Silence Adding, Deleting, or Modifying 4010 Cards, Continued Modifying a Card (continued) Technical Manuals Online! - http://www.tech-man.com

chapter describes how to add, delete, edit, etc., points in the 4010 FACP. The following information assumes you have all cards properly installed. If your cards are not installed properly or need modification, refer to “Chapter 5 - Configuring Cards.” This chapter discusses the following topics: Topic See Page # Overview 6-1 Configure Points Menu 6-2 Configuring TrueAlarm Points 6-3 Configuring ZAM/IAM/RIAM Points 6-6 Configuring Relay and NAC Points 6-9 Configuring Digital and Analog Pseudo Points 6-11 Configuring 24-Point I/O Points 6-14 Configuring List Points 6-18 Configuring User-Defined SW/LED Points 6-21 Chapter 6 Configuring Points Overview In this Chapter Programming Technical Manuals Online! - http://www.tech-man.com

menu. Figure 6-1 shows the structure of this menu. Figure 6-1. Configure Points Menu Configure Points Menu Configuring Points Menu Save CFIG • TrueAlarm • ZAMs/IAMs/RIAMs • Relay • NACs • Digital Pseudos • Analog Pseudos • 24-I/O Outputs • 24-I/O Inputs • Lists • User Defined SW/LED Programming Menus Configure Points Configure Cards Technical Manuals Online! - http://www.tech-man.com

Delete a TrueAlarm Point. Use the following steps to Add an IDNet point to the 4010 FACP. 1. Press . 2. Press or until [PROGRAMMING] is displayed and then press . A warning appears, indicating that the 4010 is no longer in the Fire Alarm Operation mode. 3. Press to continue. 4. Press or until is displayed and then press . 5. Press or to scroll through your choices until is displayed and then press . 6. Use or to scroll through your choices until is displayed and then press Enter. 7. The first unused point in the system (for example, M1-1) is displayed. Press or to scroll through your list of unused points until the desired point is displayed and then press Enter. 8. Follow the prompts to confirm this action. Note: If there are 250 devices present in the 4010 (maximum allowed), the system informs you that the IDNet channel is full and does not allow you to add any more points. Use the following steps to Edit a TrueAlarm point in the 4010 FACP. 1. Press . 2. Press or until [PROGRAMMING] is displayed and then press . A warning appears, indicating that the 4010 is no longer in the Fire Alarm Operation mode. 3. Press to continue. 4. Press or until is displayed and then press . 5. Press or to scroll through your choices until is displayed and then press . Continued on next page Configuring TrueAlarm Points Overview Add IDNet Point Edit TrueAlarm Point Programming Please Wait . . . Fire Alarm Operation Suspended Please Wait . . . Fire Alarm Operation Suspended Technical Manuals Online! - http://www.tech-man.com

displayed and then press . 5. Press or to scroll through your choices until is displayed and then press . 6. Use or to scroll through your choices until is displayed and then press Enter. 7. Press or to scroll through your list of IDNet points until the desired point is displayed and then press Enter. 8. Follow the prompts to confirm this action. Caution: Any Custom Control equations and LED/Switch Modes referencing the deleted point are also deleted. Configuring TrueAlarm Points, Continued Delete TrueAlarm Point (continued) Programming Technical Manuals Online! - http://www.tech-man.com

Use the following steps to add a ZAM/IAM/RIAM point to the 4010 FACP. 1. Press . 2. Press or until [PROGRAMMING] is displayed and then press . A warning appears, indicating that the 4010 is no longer in the Fire Alarm Operation mode. 3. Press to continue. 4. Press or until is displayed and then press . 5. Press or to scroll through your choices until is displayed and then press . 6. Use or to scroll through your choices until is displayed and then press Enter. 7. The first unused point in the system (for example, M1-1) is displayed. Press or to scroll through your list of unused points until the desired point is displayed and then press Enter. 8. Follow the prompts to confirm this action. Note: If there are 250 devices present in the 4010 (maximum allowed), the system informs you that the IDNet channel is full and does not allow you to add any more points. Use the following steps to edit a ZAM/IAM/RIAM point in the 4010 FACP. 1. Press . 2. Press or until [PROGRAMMING] is displayed and then press . A warning appears, indicating that the 4010 is no longer in the Fire Alarm Operation mode. 3. Press to continue. 4. Press or until is displayed and then press . 5. Press or to scroll through your choices until is displayed and then press . Continued on next page Configuring ZAM/IAM/RIAM Points Overview Adding ZAM/IAM/RIAM Point Editing a ZAM/IAM/RIAM Point Please Wait . . . Fire Alarm Operation Suspended Please Wait . . . Fire Alarm Operation Suspended Technical Manuals Online! - http://www.tech-man.com

FACP. 1. Press . 2. Press or until [PROGRAMMING] is displayed and then press . A warning appears, indicating that the 4010 is no longer in the Fire Alarm Operation mode. 3. Press to continue. 4. Press or until is displayed and then press . 5. Press or to scroll through your choices until is displayed and then press . 6. Use or to scroll through your choices until is displayed and then press Enter. 7. Press or to scroll through your list of IDNet points until the desired point is displayed and then press Enter. 8. Follow the prompts to confirm this action. Caution: Any Custom Control equations and LED/Switch Modes referencing the deleted point are also deleted. Configuring ZAM/IAM/RIAM Points, Continued Deleting ZAM/IAM/RIAM IDNet Point Please Wait . . . Fire Alarm Operation Suspended Technical Manuals Online! - http://www.tech-man.com

SW/LED point. The following assumes that you have chosen Relay, NAC, or User-Defined SW/LED as your option after entering the Configure Points menu. Use the following steps to configure a Relay or NAC point in the 4010 FACP. 1. Press . 2. Press or until [PROGRAMMING] is displayed and then press . A warning appears, indicating that the 4010 is no longer in the Fire Alarm Operation mode. 3. Press to continue. 4. Press or until is displayed and then press . 5. Press or to scroll through your choices until or is displayed and then press . 6. Use or to scroll through your NAC or RELAY points until the desired point is displayed and then press Enter. 7. Press or to scroll through your list of choices until the desired option is displayed and then press Enter. Your choices are shown in Table 6-3. Continued on next page Configuring Relay and NAC Points Overview Procedure Please Wait . . . Fire Alarm Operation Suspended Programming Technical Manuals Online! - http://www.tech-man.com

Function Description Edit Device Type (See Note 2) Changes the Hardware Device Type of the Point Edit Point Type (See Notes 2 and 3) Changes the Software Point Type of the Point Edit Point Label (See Note 3) Changes the 40-Character Label of the Point Clear Point Label (See Note 3) Blanks the 40-Character Label of the Point Edit Mode (See Notes 1 and 2) Changes the Mode of Operation for the Point Notes: 1. This function not allowed for NAC and Relay points. 2. For a complete list of your choices for these edit functions, refer to “Appendix A. Device and Point Types.” 3. To complete these functions, refer to their appropriate section in this publication. Configuring Relay and NAC Points, Continued Procedure (continued) Technical Manuals Online! - http://www.tech-man.com

This section describes how to configure digital pseudo points P76 through P150. P1 through P75 are system points and cannot be edited. Use the following information to configure digital pseudo points in a 4010 FACP. 1. Press . 2. Press or until [PROGRAMMING] is displayed and then press . A warning appears, indicating that the 4010 is no longer in the Fire Alarm Operation mode. 3. Press to continue. 4. Press or until is displayed and then press . 5. Press or to scroll through your choices until is displayed and then press . 6. Use or to scroll through your points until the desired point (P76 through P150) is displayed and then press Enter. 7. Press or to scroll through your list of choices until the desired option is displayed and then press Enter. Your choices are shown in Table 6-4. Continued on next page Configuring Digital and Analog Pseudo Points Overview Configuring Digital Pseudo Points Please Wait . . . Fire Alarm Operation Suspended Programming Technical Manuals Online! - http://www.tech-man.com

Function Description Edit Device Type (See Note 1) Changes the Hardware Device Type of the Point Edit Point Type (See Notes 2) Changes the Software Point Type of the Point. Your choices are: • Utility Point • Fire Point • Trouble Point • Supervisory Edit Point Label (See Note 2) Changes the 40-Character Label of the Point Clear Point Label (See Note 2) Blanks the 40-Character Label of the Point Edit Mode (See Note 1) Changes the Mode of Operation for the Point Notes: 1. This function not allowed for Digital Pseudo points. 2. To complete these functions, refer to their appropriate section in this publication. This section describes how to configure analog pseudo points A27 through A50. A1 through A26 are system points and cannot be edited. Use the following information to configure analog pseudo points in a 4010 FACP. 1. Press . 2. Press or until [PROGRAMMING] is displayed and then press . A warning appears, indicating that the 4010 is no longer in the Fire Alarm Operation mode. 3. Press to continue. Continued on next page Configuring Digital and Analog Pseudo Points, Continued Configuring Digital Pseudo Points (continued) Configuring Analog Pseudo Points Please Wait . . . Fire Alarm Operation Suspended Technical Manuals Online! - http://www.tech-man.com

displayed and then press . 5. Press or to scroll through your choices until is displayed and then press . 6. Use or to scroll through your points until the desired point (A27 through A50) is displayed and then press Enter. 7. Press or to scroll through your list of choices until the desired option is displayed and then press Enter. Your choices are shown in Table 6-5. Table 6-5. Analog Pseudo Point Configuration Choices Function Description Edit Device Type (See Note 1) Changes the Hardware Device Type of the Point Edit Point Type (See Notes 2 and 3) Changes the Software Point Type of the Point. Your choices are: • Analog • Timer • Counter Edit Point Label (See Note 3) Changes the 40-Character Label of the Point Clear Point Label (See Note 3) Blanks the 40-Character Label of the Point Edit Mode (See Note 1) Changes the Mode of Operation for the Point Notes: 1. This function not allowed for Analog Pseudo points. 2. For a complete list of your choices for these edit functions, refer to “Appendix B. Hardware and Pseudo Points.” 3. To complete these functions, refer to their appropriate section in this publication. Configuring Digital and Analog Pseudo Points, Continued Configuring Analog Pseudo Points (continued) Programming Technical Manuals Online! - http://www.tech-man.com

(switches) and control output points (Lamps, Tone-alerts, and Relays). Use the following steps to configure input points on the 24-Point I/O card. 1. Press . 2. Press or until [PROGRAMMING] is displayed and then press . A warning appears, indicating that the 4010 is no longer in the Fire Alarm Operation mode. 3. Press to continue. 4. Press or until is displayed and then press . 5. Press or to scroll through your choices until <24 IO INPUTS> is displayed and then press . 6. Use or to scroll through your points until the desired point is displayed and then press Enter. 7. Press or to scroll through your list of choices until the desired option is displayed and then press Enter. Your options are shown in Table 6-6. Configuring 24-Point I/O Points Overview Configuring 24-Point Input Points Please Wait . . . Fire Alarm Operation Suspended Technical Manuals Online! - http://www.tech-man.com

Function Description Edit Device Type Changes the Hardware Device Type of the Point. Choose Input or Output Edit Point Type Changes the Software Point Type of the Point. Your choices for Input points are: • USWITCH (2-position unsupervised switch) • OSWITCH (2-position Open supervised switch) • SSWITCH (2-position Open/Short supervised Switch) • TSWITCH (3-position supervised switch) Edit Point Label* Changes the 40-Character Label of the Point Clear Point Label* Blanks the 40-Character Label of the Point Edit Mode Changes the Mode of Operation for the Point. Your choices for modes are: • SMPL (SMPL controlled) • Ack (Acknowledge) • Fire Ack (Fire alarm acknowledge) • Supv. Ack (Supervisory alarm acknowledge) • Trouble Ack (Trouble acknowledge) • Reset (System reset) • LTEST (Lamp test) • ONOFF (On/Off switch) • TOF (Toggle On Off switch) • PBT (Push button track) • PBH (Push button hold) • DE (Disable/enable) • TDE (Toggle disable/enable) *This function not allowed for 24-Point Input points. Continued on next page Configuring 24-Point I/O Points, Continued Configuring 24-Point Input Points (continued) Programming Technical Manuals Online! - http://www.tech-man.com

1. Press . 2. Press or until [PROGRAMMING] is displayed and then press . A warning appears, indicating that the 4010 is no longer in the Fire Alarm Operation mode. 3. Press to continue. 4. Press or until is displayed and then press . 5. Press or to scroll through your choices until <24 IO OUTPUTS> is displayed and then press . 6. Use or to scroll through your points until the desired point is displayed and then press Enter. 7. Press or to scroll through your list of choices until the desired option is displayed and then press Enter. Your options are shown in Table 6-7. Continued on next page Configuring 24-Point I/O Points, Continued Configuring 24-Point Output Points Please Wait . . . Fire Alarm Operation Suspended Technical Manuals Online! - http://www.tech-man.com

Function Description Edit Device Type Changes the Hardware Device Type of the Point. Choose Input or Output Edit Point Type Changes the Software Point Type of the Point. Your choices for Output points are: • LAMP (Lamp or LED output) • PIEZO (Piezo output) • RELAY (Generic relay) • RRELAY (Relay on ‘til reset) Edit Point Label* Changes the 40-Character Label of the Point Clear Point Label* Blanks the 40-Character Label of the Point Edit Mode Changes the Mode of Operation for the Point. Your choices for modes are: • SMPL (SMPL controlled) • Fire (Fire alarm LED) • Supervisory (Supervisory LED) • Trouble (Trouble LED) • Disable (Disable LED) • On (ON LED) • Off (OFF LED) • LF (Local fire acknowledge) • LS (Local supervisory acknowledge) • LT (Local trouble acknowledge) *This function not allowed for 24-Point Output points. Configuring 24-Point I/O Points, Continued Configuring 24-Point Output Points (continued) Programming Technical Manuals Online! - http://www.tech-man.com

Use the following steps to configure a List in the 4010 FACP. 1. Press . 2. Press or until [PROGRAMMING] is displayed and then press . A warning appears, indicating that the 4010 is no longer in the Fire Alarm Operation mode. 3. Press to continue. 4. Press or until is displayed and then press . 5. Press or to scroll through your choices until is displayed and then press . 6. Use or to scroll through your lists until the desired list is displayed and then press Enter. 7. Press or to scroll through your list of choices until the desired option is displayed and then press Enter. Your choices are shown in Table 6-8. Table 6-8. List Configuration Choices Function Description Add Point (See Note 2) Allows you to add specific point(s) to a List Delete Point Allows you to delete specific point(s) from a List Delete ALL Points Allows you to delete all points from a List Edit Point Label (See Notes 1 and 3) Allows you to change the 40-Character label of the List Clear Point Label (See Notes 1 and 3) Blanks the 40-Character Label of the List Edit Point Type (See Notes 1, 2, and 3) Changes the Point Type for the List Notes: 1. This function not allowed for all Lists. 2. For a complete list of your choices for these edit functions, refer to “Appendix B. Hardware and Pseudo Points.” 3. To complete these functions, refer to their appropriate section in this publication. Continued on next page Configuring List Points Overview Configure a List Please Wait . . . Fire Alarm Operation Suspended Technical Manuals Online! - http://www.tech-man.com

TrueAlarm point is used as an example in the following steps. 1. After selecting Lists as your option under the Configure Points menu, use or to scroll through your lists until the desired list is displayed and then press . 2. Press or until Add Point is displayed and then press Enter (Figure 6-2 is displayed). Figure 6-2. Add a Point to a List Screen 3. Press or to scroll through the device types shown in the focus brackets ([ ]) until the desired device type is displayed (in this example, TrueAlarm). 4. Press the Right Arrow to move the focus brackets ([ ]) to the Add option. 5. Press or to scroll through the points you wish to add to the list. 6. Once the correct point is displayed, press Enter to add that point to the list. Repeat Steps 5 and 6 to Add all desired points to your chosen List. Use the following steps to Delete a point from a List on the 4010 FACP. A TrueAlarm point is used as an example in the following steps. 1. After selecting Lists as your option under the Configure Points menu, use or to scroll through your lists until the desired list is displayed and then press Enter. 2. Press or until the point you wish to delete is displayed and then press Enter. 3. Press or until Delete Point is displayed and then press Enter. 4. Follow the prompts to confirm this action. Continued on next page Configuring List Points, Continued Add a Point to a List Delete a Point from a List IDNet Device: 3-1 [TrueAlarm] Add 1/130 Device Type Programming Technical Manuals Online! - http://www.tech-man.com

1. After selecting Lists as your option under the Configure Points menu, use or to scroll through your lists until the desired list is displayed and then press . 2. Press or until Delete ALL Points is displayed and then press Enter. 3. Follow the prompts to confirm this action. Configuring List Points, Continued Delete ALL Points from a List Technical Manuals Online! - http://www.tech-man.com

The following assumes that you have chosen User Defined SW/LED as your option after entering the Configure Points menu. Use the following steps to configure a User-Defined Switch or LED in the 4010 FACP. 1. Press . 2. Press or until [PROGRAMMING] is displayed and then press . A warning appears, indicating that the 4010 is no longer in the Fire Alarm Operation mode. 3. Press to continue. 4. Press or until is displayed and then press . 5. Press or to scroll through your choices until is displayed and then press . 6. Press or to scroll through the choices listed below. Once your choice is displayed, press Enter. - User LED 1 - User LED 2 - User LED 3 - User Defined Key 1 - User Defined Key 2 7. Press or to scroll through your list of choices until the desired option is displayed and then press Enter. Your choices are shown in Table 6-9. Continued on next page Configuring User-Defined SW/LED Overview Configure a User-Defined Switch or LED Please Wait . . . Fire Alarm Operation Suspended Programming Technical Manuals Online! - http://www.tech-man.com

Function Description Edit Device Type (See Notes 1 and 2) Changes the Hardware Device Type of the Point Edit Point Type (See Note 2) Changes the Software Point Type of the Point Edit Point Label (See Note 1) Changes the 40-Character Label of the Point Clear Point Label (See Note 1) Blanks the 40-Character Label of the Point Edit Mode Changes the Mode of Operation for the Point Notes: 1. This function not allowed for User-Defined SW/LED. 2. Your Point Type choices for LEDs are Yellow LED or NON- Yellow LED. The switches default to USWITCH point type and is not editable. This section describes how to edit the mode of a User-Defined SW/LED. Use the following steps to edit the mode of a User-Defined Switch or LED in the 4010 FACP. 1. After selecting User Defined SW/LED as your option under the Configure Points menu, press or to scroll through the choices listed below. Once your choice is displayed, press Enter. • User LED 1 • User LED 2 • User LED 3 • User Defined Key 1 • User Defined Key 2 2. Press or to scroll through your list of choices until Edit Mode is displayed and then press Enter. Your modes for Switches and LEDs are shown in Table 6-10. Continued on next page Configuring User-Defined SW/LED, Continued Configure a User-Defined Switch or LED (continued) Edit a Mode of a User-Defined SW/LED Technical Manuals Online! - http://www.tech-man.com

User-Defined SW/LED Modes Switch Modes • SMPL • Ack • Fire Ack • Supv. Ack • Trouble Ack • Reset • Silence • LTEST • ON-OFF • TOF • PBT • PBH • DE • TDE LED Modes • SMPL • Fire • Supervisory • Trouble • Disable • On • Off • LF • LS • LT 3. Select the appropriate mode and then press Enter. 4. Follow the prompts to confirm this action. Configuring User-Defined SW/LED, Continued Edit a Mode of a User-Defined SW/LED (continued) Programming Technical Manuals Online! - http://www.tech-man.com

Active Status Reminder, etc. These options are custom functions for the 4010. The System Options (shown in Figure 7-1) can also be set from the Quick-CFIG menus. This chapter discusses the following topics: Topic See Page # System Options Menu 7-2 Time/Date Format 7-3 Active Status Reminder 7-4 Silence/Reset Inhibit 7-5 Alarm Cut-Out Timer 7-6 Door Drop on Alarm 7-7 Door Drop on AC Loss 7-8 Audible and Visual NAC Operation 7-9 TrueAlert Non-Addressable Horn Operation 7-10 Depleted Battery Cut-Out 7-11 Stagger Start AHUs 7-12 Enable City Circuit 7-13 Expansion Power 7-14 Single Station 7-15 Suppression Release 7-16 Chapter 7 System Options Overview In this Chapter Programming Technical Manuals Online! - http://www.tech-man.com

which is located in the Programming menu tree. Figure 7-1 shows the structure of the System Options menu. Figure 7-1. System Options Menu System Options Menu Introduction Configure Cards • Time/Date Format • Active Status Reminder • Silent/Reset Inhibit • Alarm Cut-Out Timer • Door Drop on Alarm • Door Drop on AC Loss • Audible NAC Operation • Visual NAC Operation • Depleted Batt. Cutout • Stagger Start AHUs • Enable City Circuit • Expansion Power • Single Station • Suppression Release • TrueAlert Horn Operation Programming Menus System Options Custom Control Technical Manuals Online! - http://www.tech-man.com

or 24-hour format. That is, the time is displayed in 12-hour format with the AM (morning) or PM (afternoon) indications or in 24-hour (military style) format. The date is always displayed in the following format and cannot be changed: Wed 27-Aug-97 Day of week, date, month, year The Time format directly affects how time is displayed on the 4010 not only at the high-level status screen but in the Historical Logs. Use the following steps to set the Time format on the 4010 FACP. 1. Press . 2. Press or until [PROGRAMMING] is displayed and then press . A warning appears, indicating that the 4010 is no longer in the Fire Alarm Operation mode. 3. Press to continue. 4. Press or until is displayed and then press . 5. Press or to scroll through your choices until is displayed and then press . 6. Press or to scroll through the options until 12 Hour or 24 Hour is displayed and then press Enter. 7. Follow the prompts to confirm this action. Time/Date Format Overview Setting the Time Format Programming Programming Technical Manuals Online! - http://www.tech-man.com

which the 4010 reminds operators of the FACP that a FIRE, SUPV, or TBL condition still exists in the panel. Your choices are as follows: • ON/OFF Status (turn the option ON or OFF). A setting of ON activates the option with a default Reminder Interval of 8 hours with a 5-second Acknowledge Option signal duration. • Reminder Interval (set a reminder interval from 1-12 hours). • Acknowledge Option (set a signal duration of 1-60 seconds). A setting of 0 seconds has the following effect: - For a Trouble condition, the signal sounds until the condition is acknowledged at the front panel. - For an Alarm (FIRE) condition, the signal sounds until the alarm condition is cleared. Use the following steps to set the Active Status Reminder on the 4010 FACP. 1. Press . 2. Press or until [PROGRAMMING] is displayed and then press . A warning appears, indicating that the 4010 is no longer in the Fire Alarm Operation mode. 3. Press to continue. 4. Press or until is displayed and then press . 5. Press or to scroll through your choices until is displayed and then press . 6. Press or to scroll through the options until On/Off Status is displayed and then press Enter. 7. Press or to select ON or OFF and then press Enter. Follow the prompts to confirm this action. 8. Press or to scroll through the options until Reminder Interval is displayed and then press Enter. 9. Press or to select an interval from 1-12 hours and then press Enter. Follow the prompts to confirm this action. 10. Press or to scroll through the options until Acknowledge Option is displayed and then press Enter. 11. Press or to select an signal duration from 0-60 seconds and then press Enter. Follow the prompts to confirm this action. Active Status Reminder Overview Setting the Active Status Reminder Technical Manuals Online! - http://www.tech-man.com

duration. The range for the Silence/Reset Inhibit timer is 0-60 minutes with zero (No Inhibit) being the default setting. Use the following steps to set the Silence/Reset Inhibit timer on the 4010 FACP. 1. Press . 2. Press or until [PROGRAMMING] is displayed and then press . A warning appears, indicating that the 4010 is no longer in the Fire Alarm Operation mode. 3. Press to continue. 4. Press or until is displayed and then press . 5. Press or to scroll through your choices until is displayed and then press . 6. Press or to set the timer from 0-60 minutes and then press Enter. 7. Follow the prompts to confirm this action. Silence/Reset Inhibit Overview Setting the Silence/Reset Inhibit Programming Technical Manuals Online! - http://www.tech-man.com

signals sound after an alarm. In other words, when an alarm condition exists, the signals sound until silenced. With this option set at two minutes, building signals sound on alarm for two minutes and then automatically stop sounding. However, the alarm condition does remain active in the panel. The default setting for this option is No Cutout (meaning a manual Alarm Silence is required to shut off signals). Use the following steps to set the Alarm Signal Cut-Out timer on the 4010 FACP. 1. Press . 2. Press or until [PROGRAMMING] is displayed and then press . A warning appears, indicating that the 4010 is no longer in the Fire Alarm Operation mode. 3. Press to continue. 4. Press or until is displayed and then press . 5. Press or to scroll through your choices until is displayed and then press . 6. Press or to set the timer from 0-60 minutes and then press Enter. 7. Follow the prompts to confirm this action. Alarm Cut-Out Timer Overview Setting the Alarm Cut-Out Timer Technical Manuals Online! - http://www.tech-man.com

for a set duration during an alarm condition. After that duration has expired, the 4010 shuts off the door holder relays and the doors close. The range for the timer is 0-60 seconds with a default setting of zero seconds. To have door holders drop the doors immediately, leave the timer set to zero seconds. Use the following steps to set the Door Holder Alarm Door Drop timer on the 4010 FACP. 1. Press . 2. Press or until [PROGRAMMING] is displayed and then press . A warning appears, indicating that the 4010 is no longer in the Fire Alarm Operation mode. 3. Press to continue. 4. Press or until is displayed and then press . 5. Press or to scroll through your choices until is displayed and then press . 6. Press or to set the timer from 0-60 seconds and then press Enter. 7. Follow the prompts to confirm this action. Door Drop on Alarm Overview Setting the Door Drop on Alarm Timer Programming Technical Manuals Online! - http://www.tech-man.com

open for a set duration during an AC power loss condition. After that duration has expired, the 4010 shuts off the door holder devices and the doors close. The range for the timer is 0-60 minutes, with a default setting of 5 minutes. To have door holders drop the doors immediately upon AC power loss, set the timer to zero minutes. Use the following steps to set the Door Holder AC Fail Door Drop timer on the 4010 FACP. 1. Press . 2. Press or until [PROGRAMMING] is displayed and then press . A warning appears, indicating that the 4010 is no longer in the Fire Alarm Operation mode. 3. Press to continue. 4. Press or until is displayed and then press . 5. Press or to scroll through your choices until is displayed and then press . 6. Press or to set the timer from 0-60 minutes and then press Enter. 7. Follow the prompts to confirm this action. Door Drop on AC Loss Overview Setting the Door Drop on AC Loss Timer Technical Manuals Online! - http://www.tech-man.com

can be set to the choices shown in Table 7-1. The default setting for the Audible NACs is Temporal coding and the default setting for the Visible NACs is Steady. Refer to “Appendix C - Glossary of Terms” for more information on the types of coding. Use the following steps to set the Audible and/or Visual NAC operation on the 4010 FACP. 1. Press . 2. Press or until [PROGRAMMING] is displayed and then press . A warning appears, indicating that the 4010 is no longer in the Fire Alarm Operation mode. 3. Press to continue. 4. Press or until is displayed and then press . 5. Press or to scroll through your choices until or is displayed and then press . 6. Press or to choose the settings shown in Table 7-1. Table 7-1. Audible and Visual NAC Operation Settings System Option Choices Audible NAC Operation Choose: • Audible NACs: Temporal* • Audible NACs: Steady • Audible NACs: Slow March • Audible NACs: Fast March Visual NAC Operation Choose: • Visual NACs: Steady* • Visual NACs: Slow March • Visual NACs: Fast March • Visual NACs: Temporal • Visual NACs: Synchronous * Default Settings Follow the prompts to confirm this action. Audible and Visible NAC Operation Overview Setting the Audible or Visual NAC Operation Programming Technical Manuals Online! - http://www.tech-man.com

TrueAlert Horns function when activated. The default function is Temporal. Use the following steps to set the TrueAlert Non-Addressable Horn system option. 1. Press . 2. Press or until [PROGRAMMING] is displayed and then press . A warning appears, indicating that the 4010 is no longer in the Fire Alarm Operation mode. 3. Press to continue. 4. Press or until is displayed and then press . 5. Press or to scroll through your choices until is displayed and then press . 6. Press or to choose the settings shown in Table 7-2. Table 7-2. Audible and Visual NAC Operation Settings System Option Choices TrueAlert Non-Addressable Horn Operation Choose: • Temporal* • Steady • Slow March * Default Settings Follow the prompts to confirm this action. TrueAlert Non-Addressable Horn Operation Introduction Setting the TrueAlert Non- Addressable Horn Option Technical Manuals Online! - http://www.tech-man.com

during an AC power loss while a Depleted Battery trouble exists. The specific operation of this option differs slightly, depending on whether you have a domestic or Canadian system. Domestic Operation. The default setting for the option is OFF and the threshold voltage is 19.4 VDC ± 5%. Operation of this option for a domestic system is as follows: • If the system is in alarm and a depleted battery condition occurs, any NACs that are active remain active. • If the system in not in alarm and a depleted battery condition occurs, the NACs are prevented from activating. Canadian Operation. The default setting for the option is OFF and the threshold voltage is 19.4 VDC ± 5%. Operation of this option for a Canadian system is as follows: • When a depleted battery condition occurs, power is turned off to the 4010. AC power must be restored to re-activate the 4010. Use the following steps to set the Depleted Battery Cut-Out on the 4010 FACP. 1. Press . 2. Press or until [PROGRAMMING] is displayed and then press . A warning appears, indicating that the 4010 is no longer in the Fire Alarm Operation mode. 3. Press to continue. 4. Press or until is displayed and then press . 5. Press or to scroll through your choices until is displayed and then press . 6. Press or to set the option to ON or OFF and then press Enter. 7. Follow the prompts to confirm this action. Depleted Battery Cut-Out Overview Setting the Depleted Battery Cut-Out Programming Technical Manuals Online! - http://www.tech-man.com

(AHUs) control points (point types AHUR, AHUO, and AHUF) in the 4010 FACP . This option protects against power spikes that may cause the circuit breakers to trip when AHUs start simultaneously. The range for stagger starting the AHUs is 0-60 seconds. The default setting for this option is 30 seconds. A setting of zero allows the AHUs to start immediately. The 4010 displays an AHU Stagger Start message when the sequence starts and an AHU Stagger Start Complete message when the sequence ends. Use the following steps to set the Stagger Start AHUs timer on the 4010 FACP. 1. Press . 2. Press or until [PROGRAMMING] is displayed and then press . A warning appears, indicating that the 4010 is no longer in the Fire Alarm Operation mode. 3. Press to continue. 4. Press or until is displayed and then press . 5. Press or to scroll through your choices until is displayed and then press . 6. Press or to set the timer from 0-60 seconds and then press Enter. 7. Follow the prompts to confirm this action. Stagger Start AHUs Overview Setting the Stagger Start AHU Delay Timer Technical Manuals Online! - http://www.tech-man.com

installing the city circuit card. The default setting for the city circuit is OFF. Use the following steps to set the Enable City Circuit option on the 4010 FACP. 1. Press . 2. Press or until [PROGRAMMING] is displayed and then press . A warning appears, indicating that the 4010 is no longer in the Fire Alarm Operation mode. 3. Press to continue. 4. Press or until is displayed and then press . 5. Press or to scroll through your choices until is displayed and then press . 6. Press or to set the option to ON or OFF and then press Enter. 7. Follow the prompts to confirm this action. Enable City Circuit Overview Setting the Enable City Circuit Option Programming Technical Manuals Online! - http://www.tech-man.com

menu when installing the expansion power supply. The default setting for the expansion power supply is OFF. Use the following steps to set the Expansion Power Supply option on the 4010 FACP. 1. Press . 2. Press or until [PROGRAMMING] is displayed and then press . A warning appears, indicating that the 4010 is no longer in the Fire Alarm Operation mode. 3. Press to continue. 4. Press or until is displayed and then press . 5. Press or to scroll through your choices until is displayed and then press . 6. Press or to set the option to ON or OFF and then press Enter. 7. Follow the prompts to confirm this action. Expansion Power Overview Setting the Expansion Power Option Technical Manuals Online! - http://www.tech-man.com