Ferroli ZU0800009 Installation & User's Instructions

Part number: ZU0800009 Radio Thermostat Clock 80.10.1375.7_feeling_ks_fer_en.indd 1 18.04.2013 11:25:42

Safety instructions................................ 3 Product details...................................... 4 Installation and assembly...................... 7 Operating and adjustment................... 15 Configuration...................................... 18 Initial start-up..................................... 19 Settings.............................................. 25 Operating modes................................ 29 Operating status................................. 36 User menu/Configuration.................... 39 Installation menu................................ 40 80.10.1375.7_feeling_ks_fer_en.indd 2 18.04.2013 11:25:42

 The connection and installation of electrical devices may only be carried out by a qualified electrician. DANGER • It is imperative to observe the generally applicable safety measures, e.g. before starting any work on the appliance, switch off power supply and secure against switching on. • Interventions in and changes to the device result in the voiding of the warranty claim. • Observe your national regulations and the respective safety provisions. 80.10.1375.7_feeling_ks_fer_en.indd 3 18.04.2013 11:25:42

(RF) wireless thermostat/ timer which communicates with a special receiver designed to fit in the clock aperture of the boiler casing. The radio thermostat clock is battery powered and can be sited wherever conventional room thermostats would normally be sited. See installation locations information on page 7. The radio thermostat clock is a room thermostat and clock of highly advanced technology. The device is wireless and controls the heating via radio, providing both time control and comfortable room temperatures. Assembly description A Moveable sliding cover B Keys for manual override function C Window D Keyboard E Battery compartment F Display 80.10.1375.7_feeling_ks_fer_en.indd 4 18.04.2013 11:25:43

Power supply: 2 x 1.5 V AA LR6 alkaline batteries Battery service life: 2 years (depending on switching frequency) Room temperature display resolution: 0.1ºC Temperature setting display: Program: +5ºC…+32ºC (0.5ºC steps) Frost protection: 5ºC (adjustable 3ºC…7ºC) Time setting resolution: Time of day: 1 minute Program: 30 minutes Programming: weekly program with up to 48 time and temperature programs changes Pre-programmed programs: 4 + 1 user-defined RF signal: 868.3 MHz RF signal range: Indoor 30 m (2 walls + 1 ceiling) Protection class / type: II / IP40 Operating temperature range: Max. 45ºC Operating humidity range: 10% to 90% RH non-condensing Dimensions H x W x D (mm): 87 x 154 x 27 80.10.1375.7_feeling_ks_fer_en.indd 5 18.04.2013 11:25:43

Power supply: 230 V +/-10% 50-60 Hz Switching output: SPDT (potential-free) Switching capacity: 5 (1) A 250 V AC RF signal: 868.3 MHz RF signal range: Indoor 30 m (2 walls + 1 ceiling) Protection class / type: II / IP20 Operating temperature range: Max. 45ºC Operating humidity range: 10% to 90% RH non-condensing Dimensions H x W x D (mm): 60 x 60 x 32 80.10.1375.7_feeling_ks_fer_en.indd 6 18.04.2013 11:25:43

General information 80.10.1375.7_feeling_ks_fer_en.indd 7 18.04.2013 11:25:43

the clock Remove Link and connect leads to terminals 3 & 4 at the receiver White L White N Radio Thermostat Clock Receiver 80.10.1375.7_feeling_ks_fer_en.indd 9 18.04.2013 11:25:44

2 - Neutral (Blue) 3 - Switched circuit (White #1) 4 - Switched circuit (White #2) 5 - No connection required Commissioning, please turn to page 11. Receiver Button LED Installation of the receiver M~ 1 2 3 4 5 80.10.1375.7_feeling_ks_fer_en.indd 10 18.04.2013 11:25:44

The transmitter and receiver are pre-commissioned. If the radio link doesn‘t work correct, follow the sequence of commissioning. Press and hold the black button of the receiver until the LED light has flashed twice. Release the button and the LED light will remain illuminated. Press and hold MODE-button and SET-button of the transmitter at the same time for more than 3 seconds to enter into the User menu. Then press the ok-button until RF Comm is displayed. 80.10.1375.7_feeling_ks_fer_en.indd 11 18.04.2013 11:25:44

LED will go out as soon as a signal from the transmitter is received. Then press the ok-button, the radio link between transmitter and receiver is now established. Press the Esc-button to return to Auto mode. Receiver: When operating in heating mode and an ON signal is received, the LED illuminates continously. When an OFF signal is received, the LED is off (and flashes periodically at longer intervals). Is no valid radio signal received from the transmitter for more than one hour (e.g. low battery) the emergency operating mode will be activated. The LED flashes every 0,5 seconds. 80.10.1375.7_feeling_ks_fer_en.indd 12 18.04.2013 11:25:45

click! click! Close housing Insert batteries 80.10.1375.7_feeling_ks_fer_en.indd 14 18.04.2013 11:25:46

Operating information • Flashing texts signal the need for an entry. If no button is pressed for 2 minutes, the device reverts to the Automatic mode. • All settings need to be confirmed with OK. • All settings saved will remain in the memory. • The histogram shows the programmed temperature profile 7 – 14°C = displayed as one segment 15 – 24°C = one segment displays 1°C over 24°C = one segment displays 2°C 80.10.1375.7_feeling_ks_fer_en.indd 15 18.04.2013 11:25:46

B Battery C RF signal D Current time E Set temperature F Off mode G Histogram over 24 hours H Current temperature I Operating mode J Status indication K Current date Display A C D E F G H I J K B 80.10.1375.7_feeling_ks_fer_en.indd 16 18.04.2013 11:25:47

temperatures. B OK-button to confirm settings and go to the next step. C Mode-button to select from the available operating modes. D Esc-button used for ON/OFF, go one step back in menu or return to main menu by pressing the button more than 3 seconds. E Set-button for settings following commissioning. F +/– buttons used to increase/decrease hours, days and events. G Reset-button to return to factory settings. The programs are retained in the case of a reset. The date and time must be set again. Press reset button with a blunt object (pen). A C E B F G D 80.10.1375.7_feeling_ks_fer_en.indd 17 18.04.2013 11:25:47

following informations: D A B C A Sequence of operation B Pressed buttons are shown in black. C Flashing elements are shown in black D Fixed elements are shown in grey • Buttons which can be pressed during an action are shown in black. The related display is also shown in black. • Follow exactly the numbers of the sequence of operation. • The configuration of the device is described based on configuration. • After starting the device for the first time, follow the menu for a correct configuration of the device. • Following commissioning, you can also change the configuration by pressing the set-button. 80.10.1375.7_feeling_ks_fer_en.indd 18 18.04.2013 11:25:47

Sequence for setting the date and time during initial start-up. 15/6/2008 appears as factory default. To set the date and time after initial start-up press the SET-button, then choose Date or Time Menu with the upper +/– buttons and confirm with OK. 80.10.1375.7_feeling_ks_fer_en.indd 19 18.04.2013 11:25:48

80.10.1375.7_feeling_ks_fer_en.indd 20 18.04.2013 11:25:49

To specify programs after initial start-up press the SET-button, then choose the Prog menu with the upper +/– buttons and confirm with OK. 80.10.1375.7_feeling_ks_fer_en.indd 21 18.04.2013 11:25:49

5-2 days – one program per day block 1-7 days – each day an individual program free block formation – one program per day block 80.10.1375.7_feeling_ks_fer_en.indd 22 18.04.2013 11:25:51

defined). Pd User-defined program. During initial start-up, program will be shown with 15ºC from 00:00 to 23:59 PM. P1 15°C 20°C 17°C 21°C 15°C P3 15°C 20°C 17°C 21°C 15°C 20°C 18°C P2 15°C 20°C 17°C 21°C 15°C P4 15°C 20°C 17°C 21°C 15°C 80.10.1375.7_feeling_ks_fer_en.indd 23 18.04.2013 11:25:51

the temperature of each segment by 0.5°C. Use the lower +/– buttons to go forward/backward 30 minutes each time and copy the selected temperature value. 80.10.1375.7_feeling_ks_fer_en.indd 24 18.04.2013 11:25:52

the upper +/– buttons you jump to the different menus. 1-3 = adjustment of date 2-3 = adjustment of time 3-3 = adjustment of time and temperature programming 80.10.1375.7_feeling_ks_fer_en.indd 25 18.04.2013 11:25:52

in the initial start-up. The sequence of setting the time is similar to the method for settingthe date. With the lower +/– buttons you can choose days or day blocks for programming and confirm with OK. Go to operation number . By pressing the ok-button you can choose between the pre-defined programs P1 – P4 or the user-defined program Pd. Go to operation number . 80.10.1375.7_feeling_ks_fer_en.indd 26 18.04.2013 11:25:53

through the program to check it. For editing the program, use the upper +/– buttons to increase/decrease temperature in each segment by 0.5°C. Use the lower +/– buttons to go forward/backward and copy the selected temperature value. 80.10.1375.7_feeling_ks_fer_en.indd 28 18.04.2013 11:25:55

Follow the sequence for selecting the desired operating mode. The operating modes in the device appear in the same order as described here. Press and hold the ESC-button for 3 seconds to return to Auto mode. Example: 80.10.1375.7_feeling_ks_fer_en.indd 29 18.04.2013 11:25:55

user-defined program run here. 80.10.1375.7_feeling_ks_fer_en.indd 30 18.04.2013 11:25:55

is kept for the whole day until any user‘s intervention is made. To return to Auto mode, press OK. The average temperature is the starting point for increasing or decreasing the desired temperature, pressing upper +/– buttons. The new temperature set value is then, after 3 sec., set for all day long. Example: 4 different temperatures in the actual program (e.g. 17°C, 19°C, 20°C and 22°C). Average temperature is then 19,5°C. 80.10.1375.7_feeling_ks_fer_en.indd 31 18.04.2013 11:25:56

remaining time is shown until running mode elapsed. After the Cleaning mode is elapsed, the device returns into Auto mode. To end Cleaning mode early, press Esc-button for more than 3 seconds. The anti-freeze protection is granted. 80.10.1375.7_feeling_ks_fer_en.indd 32 18.04.2013 11:25:56

of time is 1 – 23 hours. After the time is elapsed, the device returns into OFF mode (Anti-freeze temperature is kept). During the Countdown mode, remaining countdown time is indicated. Example: The device shall be run into OFF mode after 4 hours. To end Countdown mode early, press Esc-button for more than 3 seconds. 80.10.1375.7_feeling_ks_fer_en.indd 33 18.04.2013 11:25:56

period of time is 1 – 23 hours. After the time is elapsed, the device returns into the mode before the Party mode was activated. During the Party mode, the rest of the time is indicated. Example: The temperature shall be set for 6 hours on 24°C. To end Party mode early, press Esc-button for more than 3 seconds. 80.10.1375.7_feeling_ks_fer_en.indd 34 18.04.2013 11:25:57

of time is 1 – 90 days. After the time is elapsed, the device returns into the mode before the Holiday mode was activated. During the Holiday mode, the rest of the days is indicated. Example: The temperature shall be set for 16 days on 13°C. To end Holiday mode early, press Esc-button for more than 3 seconds. 80.10.1375.7_feeling_ks_fer_en.indd 35 18.04.2013 11:25:57

with the upper +/– buttons. It is not necessary to confirm the setting with OK. The setting will remain as temperature set value until the next programmed change (time and temperature) appears. To return into Auto mode, press and hold upper +/– buttons for 3 seconds, or open the sliding cover and press OK-button. 80.10.1375.7_feeling_ks_fer_en.indd 36 18.04.2013 11:25:58

for more than 5 seconds. To leave this mode press and hold the On/Off/Esc-button again for more than 5 seconds. The anti-freeze protection is granted. >5 sec 80.10.1375.7_feeling_ks_fer_en.indd 37 18.04.2013 11:25:58

batteries are not placed or are installed in the wrong polarity, text will appears on display until they are placed or installed in the right polarity. If the battery goes completely empty, the programming is protected. 80.10.1375.7_feeling_ks_fer_en.indd 38 18.04.2013 11:25:58

To go to previous menu press Esc-button. It is possible to adjust: • RF commissioning (RFC): Enable/disable continuous radio signal • Offset (OFS): Possibility to adjust/modify the measured temperature (-5°C...+5°C) • Summer/Winter time (SWT): enable/disable automatic summer/winter time change • Time Format (TMF): possibility to change time format into 24 hours or 12 hours (default: 24 hours) • Restore Default (DFL): Restore values to factory default status. Use lower +/– buttons to navigate through menus. Use upper +/– buttons to change values and OK to confirm. 80.10.1375.7_feeling_ks_fer_en.indd 39 18.04.2013 11:25:58

time until Installer menu is shown in the display. Press ESC-button to go to previous Menu. The adjustments in this menu are only for experts. All possibilities for adjustment are shown with a self-explaining, floating real text in the display. Use lower +/– buttons to navigate through menus. Use upper +/– buttons to change values and OK to confirm. 80.10.1375.7_feeling_ks_fer_en.indd 40 18.04.2013 11:25:59

High Temp (HIT): set maximum temperature value for programming from low temperature value up to +32°C (default: +32°C) Low Temp (LOT): set minimum temperature value for programming from +7°C up to high temperature value (default: +7°C) Frost protection (FRT): set anti freeze minimum temperature value from +3°C to +7°C (default: 5°C) Regulation (REG): possibility to select between PID or 2 points regulation (default: 2 points) Differential (DIF): possibility to modify differential value from 0,1 K to 0,9 K (default: 0,2 K) Keypad Lock (LOK): enable keypad to protect against non authorized interventions To enable/disable the keypad lock press and hold Mode- and ESC-button for more than 3 seconds. Operating hours (OPT): this feature shows total operating running time (max. 99.999 hours) Battery Level (BAT): battery charge level is shown on display 80.10.1375.7_feeling_ks_fer_en.indd 41 18.04.2013 11:25:59

Staffordhshire, DE14 3HD Service/Technical Tel: 0843 479 0 479 Because of our constant endeavour for improvement details may vary from those quoted in these instructions Should you require any assistance during the installation call our Technical Service Helpline on 0843 479 0 479 80.10.1375.7_feeling_ks_fer_en.indd 44 18.04.2013 11:25:59