Extech Instruments 401025 Operation & User’s Manual

care, will provide years of safe reliable service. Meter Description 1. LCD Display 2. Data Hold Switch 3. Power Off/Range Switch 4. Analog Output Terminal 5. Battery Compartment (rear) 6. LUX/Fc Switch & Response Switch 7. Light Sensor 8. Zero adjust Operation 1. Select Units (Lux or Ft-candle) and Response Time (Fast or Slow) on the slide switch. Typical selection is Slow and Fc using the gray lettering. 2. Select the maximum range on the "Range Switch" 3. Hold the "Light Sensor" so that the sensor faces the light source to be measured. 4. The Display will indicate measured values. Use a range display multiplier if on the Lux 20,000 and 50,000 ranges or on the Fc 5000 range. 5. To "hold" a measurement, slide the "Data Hold Switch" to the "hold" position. The reading will "freeze" in the display until the "Data Hold Switch" is released. Note 1: An Over Range indication is a display of "I ". If this occurs, switch to a higher range. Note 2: For measurements made on the Fc 5000 range, the displayed reading must be multiplied by 10. Note 3: For measurements made on the Lux 20000 or 50000 range, the displayed reading must be multiplied by 10 and 100 respectively. Note 4: The meter will indicate values above the maximum ranges. The accuracy of these measurements is unknown. Range Display Multipliers Range Units Multiplier 200 Fc Direct reading 2000 Fc & Lux Direct reading 5000 Fc Reading x10 20,000 Lux Reading x10 50,000 Lux Reading x100 Example: If a measurement on the 5000 Fc range displays 350, then the actual measured value is; 350 X 10 = 3500 Fc.

The meter has three measurement ranges (0-200, 0-2000, and 0-5000 Fc) and (0-2000, 0-20000, and 0-50000) Lux). The proper range selection will produce the most accurate reading. Always select the range that produces the maximum number of digits without exceeding the maximum count for that particular range. For example, a reading of 1456 Fc should be read on the 0 - 2000 range, not the 0- 5000 range. Zero procedure The meter zero (display with no light input) may change with time. Occasional checking and adjustment may be required. 1. Completely cover the sensor to block out any light. 2. Set the range switch to the lowest Lux or Fc range 3. Using a small screwdriver, adjust the “Zero” control for a zero display. The last digit may change slightly. This is normal and does not affect the accuracy of the meter. Analog Output The analog output jacks on the front panel produce a 0.1mV DC per digit signal that can be used for recording or datalogging purposes. Lighting Type Correction Factors The 401025 light meter is calibrated under a precise "Standard tungsten light source of 2856 OK". If the meter is to be used under a different type of light the correction factor of from the table below should be applied to the readings obtained. Mercury Lamp x1.14 Fluorescent Lamp X0.92 to 1.12 Daylight x1.00 Sodium x1.22 Metal Halide x1.00 Replacing the Battery When the left corner of the LCD display shows "LO BAT", it indicates the battery output is below the design limit and the battery needs to be replaced. However, reliable measurement can still be taken for another few hours before the tester becomes inaccurate. 1. Open the Battery Cover at the back of tester and remove the battery. 2. Replace with a 9V battery and install the cover. You, as the end user, are legally bound (EU Battery ordinance) to return all used batteries, disposal in the household garbage is prohibited! You can hand over your used batteries / accumulators at collection points in your community or wherever batteries / accumulators are sold! Disposal: Follow the valid legal stipulations in respect of the disposal of the device at the end of its lifecycle

Measurement Lux, Ft-candle (Fc). Ranges Lux: 0 to 50,000 Lux, 3 ranges. Foot-candle: 0-5,000 Fc, 3 ranges. Sensor Exclusive photo diode & color correction filter, spectrum designed to meet C. I. E. Zero Adj. Manual adjustment. Sampling Time Approx. 0.4 sec. Response Time Fast: 0.25s; Slow: 1s Over input indication Indication of "1 " Analog Output 0.1 mV/1 digit, max. output :200mV. Operating Temperature 0 OC to 50 OC (32 OF to 122 OF) Operating Humidity Less than 80% RH. Power Supply 006P DC 9V battery Power Current Approx. 2 mA DC Weight 220 g / 0.52 LB Dimension Main instrument: 163x70x30mm (6.4x2.8x1.2 inch). Sensor Probe: 85x55x12 mm (3.2x2.2x0.5 inch). Optional Accessories Vinyl pouch carrying case, 409996 Range Specifications Lux Range In-range Display Resolution Accuracy 2,000 Lux 0-1,999 Lux 1 Lux ± (5% + 2digits) 20,000 Lux 2,000-19,990 Lux 10 Lux ± (5 % + 2digits) 50,000 Lux 20,000-50,000 Lux 100 Lux ±- (5 % + 2digits) Foot-candle (Fc) Range In-range Display Resolution Accuracy 200 Fc 0-199.9 Fc 0.1 Fc ± (5% + 2digits) 2,000 Fc 200-1,999 Fc 1 Fc ± (5% + 2digits) 5,000 Fc 2,000-5,000 Fc 10 Fc ± (5% + 2digits) Frequency Spectrum 300 400 500 600 700 800 1 0.8 0.6 0.4 0.2 0 Wavelength (nm)

Lux Foot Candles Lux Foot Candles Factories Home 20-75 2-7 Emergency Stairs, Warehouse 100-150 10-15 Washing 75-150 7-15 Exit/Entrance Passages 150-200 15-20 Recreational Activities 150-300 15-30 Packing Work 200-300 20-30 Drawing Room, Table 300-750 30-75 Visual Work: Production Line 300-500 30-50 Makeup 750-1,500 75-150 Typesetting: Inspection Work 500-1,500 50-150 Reading, Study 1,500- 3,000 150-300 Electronic Assembly, Drafting 1,000- 2,000 100-200 Sewing Office Restaurant 75-100 7-10 Indoor Emergency Stairs 75-150 7-15 Corridor Stairs 100-200 10-20 Corridor Stairs 150-300 15-30 Entrance, Wash Room 200-750 20-75 Conference, Reception Room 300-750 30-75 Cooking/Dining Room 750-1,500 75-150 Clerical Work 750-1,500 75-150 Show Window 1,500- 2,000 150-2000 Typing, Drafting Store Hospital 75-150 7-15 Indoors 30-75 3-7 Emergency Stairs 150-200 15-20 Corridor/Stairs 75-100 7-10 Stairs 200-300 20-30 Reception 100-150 10-15 Sick Room, Warehouse 300-500 30-50 Display Stand 150-200 15-20 Waiting Room 500-750 50-75 Elevator 200-750 20-75 Medical Exam Room 750-1,500 75-150 Show Window, Packing Table 750-1,500 75-150 Operating Room 1,500- 3,000 150-300 Storefront, Show Window 5,000- 10,000 500-1000 Eye Inspection Appendix B - Common Terms and Conversion Factors 1 lux (lx) 10-4 lm/cm2 10-4 phot (ph) 9.290 x 10-2 lm/ft2 Illuminance (Visible Flux Density) 1 lm/m2 = 9.290 x 10-2 foot-candles Luminance (Visible Flux Density per Solid Angle) 1 lm/m2/sr = 1 candela/m2 Luminous Intensity (Visible Flux per Solid Angle) 1 lm/sr = 1 candella Luminous Flux ( Visible Flux) 1 lumen (lm) = 1.464 x 10-3 watts @ 555 nm Copyright © 2012 Extech Instruments Corporation (a FLIR company) All rights reserved including the right of reproduction in whole or in part in any form. www.extech.com