FingerTec TA500 Installation Manual

TA500 1 2ABC 3DEF ESC 7PQRS 5JKL 4GHI 8TUV 9WXYZ 6MNO 0 / M/OK ........ s u p p o r t @ f i n g e r t e c . c o m TA500 1 2ABC 3DEF ESC 7PQRS 5JKL 4GHI 8TUV 9WXYZ 6MNO 0 / M/OK Installation Guide TA500 Biometrics Time Attendance System Step 1 Determine the Location and Position of the Installation • Avoid installing the terminals in locations that have contact with a strong light source (e.g direct sunlight, spotlight, fluorescent light, etc) • Avoid installing the terminals in locations prone to high moisture or condensation levels in the air • The recommended installation height of the terminals from the ground is 1.2 meter. Step 2 Mounting Terminals It is recommended that the terminals be mounted to a wall in to ease the process of enrolment and verification. In a situation whereby mounting the terminals on a wall is not an option, you can choose to use flexi kit to convert the terminals to desktop units. However, there are limited options for the flexi kit and some termi- nals might not be suitable to be placed on flexi kits. A. MOUNT ON WALL • After measuring the height accordingly and make rel- evant marking on the wall, drill the screws into the wall to secure the back plate. • Attach the terminal to the back plate and tighten the screws. Refer to Appendix I for dimensions and meas- urements of installation. B. FLEXI-KIT FingerTec offers flexi-kit for all its time attendance models. Attach the terminal on the flexi-kit for convenience. Step 3 Wiring for Power Supply Please use the power adaptor provided in the package or alterna- tively you can opt for a linear power supply with specifications of 5VDC 2A. Plug one point of the power adapter to the terminal and the other end to the power outlet. Don’t exceed the recom-mended voltage or current to avoid damaging the terminal. Step 4 Setting Up Data Communication (Skip this step if you are using USB flash disk to transfer data) TCP/IP – LAN Connection For TCP/IP connection, plug the special RJ45 jack into the TCP/IP (LAN) Port of the terminal. Connect the other end (normal RJ45 jack) to the local area network hub or a PC. Configure the device ID, IP ad- dress, subnet mask and Gateway in the terminal (refer to the hard- ware user manual for details). © 2014 Timetec Computing Sdn Bhd. All rights reserved.• 112014 4 feet / 1.2 meter (recommended) POWER PORT TCP/IP PORT

1. Check that all cable connections are done correctly. 2. Attach the terminal to the corresponding back plates and tighten the screws to secure the terminal on the wall. 3. Switch on the power to the terminal. 4. Start using the terminal. Other Accessories FingerTec offers complementing accessories which can be used with your terminals. These optional accessories are available at http://accessory.fingertec.com AdapTec Plus The AdapTec Plus is a 12VDC power supply inclusive of a 110~240VAC switching linear power. The AdapTec supplies 12VDC power to the FingerTec terminal and door lock system as well as charges a 12VDC 7.0Ah backup battery simultaneously. During an event of a power failure, the back up battery automatically provides power to the terminal and maintains the door lock system.The AdapTec Plus also prevents a secured door from being opened if it has been tampered with. Mini UPS Mini UPS 12VDC is a mini portable backup pow- er supply with 12VDC output, supplying 12VDC power for FingerTec Time Attendance terminals. meddled with by unauthorized persons. Flexi Kit A simple stand which can be used to support your terminal. You can use Flexi-Kit and convert your terminal into a desktop unit. By install- ing the terminals onto a Flexi-Kit, you do not need to go through the process of mounting your terminals on a wall. The simplicity of the Flexi-Kit’s design ensures that it is portable and easy to set up, mak- ing it ideal as a demonstration prop too. Appendix I Terminal Dimensions and Measurements Front View of Back Plate