Digital Watchdog MEGApix DWC-MPTZ20XFM Operation & User’s Manual

I n i t i a l l y , t h e f a c t o r y d e f a u l t s e t t i n g s w i l l a p p e a r ; h o w e v e r , y o u m a y c u s t o m i z e t h e C o l o r S e t t i n g s f o r y o u r M E G A P I X c a m e r a . Extra Settings: control the camera’s Day & Night Mode, Focus, WDR, Flip, Digital Zoom, Aperture Level, and Noise Reduction. 4. Flip- Select On or Off to flip the image upside down. 5. Digital Zoom- enable or disable the camera's 32x Digital Zoom option. This is different from the camera’s Web Viewer zoom and enables the came ...

b a c k u p . W h e n s e t u p p r o p e r l y , t h e c a m e r a w i l l r e c o r d t o t h e l o c a l S D c a r d w h e n i t d e t e c t s i t i s n o t r e c o r d i n g t o a n y s e r v e r s a n d i s n o t c o n n e c t e d t o t h e n e t w o r k . ...

2 3 5. Run all the necessary cables via the mounting accessory’s bracket to the upper housing. 6. Connect each of the following cables to the applicable port. Use the diagram below for more information.* a. Alarm In/ Out Port b. Audio In Port c. Audio Out Port d. Network Cable Port e. Power Port f. Micro SD Card Slot & Cover 7. Check the LED lights are on. Green light flickers when the camera is booting, and Red light turns on when booting is complete. * See pages 17-20 for proper cabling connections and SD Card installation. ...

I f y o u d o n o t u s e a p u b l i c I P a d d r e s s , D D N S p r o v i d e s y o u t o c o n n e c t o n W A N . D D N S a l l o w s y o u t o c o n n e c t t o t h e M E G A P I X c a m e r a w i t h a U R L a d d r e s s i n s t e a d o f a n I P a d d r e s s . D D N S a u t o m a t i c a l l y r e d i r e c t s t r a f f i c t o y o u r I P a d d r e s s e v e r y t i m e i t c h a n g e s . 1. To use DDNS, select the Use DDNS checkbox. 2. Select one of the DDNS System Names from t ...

S e t t i n g t h e I P A d d r e s s f o r y o u r P C Dynamic Host Configuration Protocol (DHCP) is the default setting for the camera. If the MEGAPIX camera is connected to a DHCP network and the camera’s IP Configuration Mode is set to DHCP, the server will automatically assign an IP address to the camera. If the camera is using DHCP, the default IP address will be 192.168.1.123, and the default subnet mask will be 255.255.255.0. The MEGAPIX camera can also connect to the web viewer u ...

S e n d a n e - m a i l n o t i f i c a t i o n f r o m t h e c a m e r a b a s e d o n e v e n t s s u c h a s s e n s o r a c t i v a t i o n , m o t i o n d e t e c t i o n , c a m e r a r e b o o t o r u p g r a d e . 1. Select Use Event Mail option. Select Event Type. 2. Enter SMTP Server information. Example: smtp.gmail.com. 3. Enter Username and Password. 4. Enter Sender E-mail. 5. Add the E-mail(s) you wish to send the notifications to. 6. Select Apply to save changes. 7 5 * Email Notifications do not support TSL/SSL op ...

U s e t h i s s e t u p m e n u t o c o n f i g u r e a n d m o d i f y t h e c a m e r a ’ s S w i n g f e a t u r e . W h e n t h e s w i n g f u n c t i o n r u n s , t h e c a m e r a m o v e s b e t w e e n t w o ( 2 ) a s s i g n e d p o s i t i o n s b a s e d o n t h e d i r e c t i o n s e t b y t h e u s e r . T h e c a m e r a s u p p o r t s u p t o 8 S w i n g p a t t e r n s . T o s e t u p a S w i n g : 8. Set the Swing’s first and second positions. a. Move the camera to the position you want to set as t ...

2. Remove the protective plastic to expose the four (4) screw holes. 3. Using the Mounting Box or the Mounting Template, locate on the wall/ ceiling the locations for the four (4) bolts. Note: the Anchor bolts included in with the camera kit are for concrete. Be sure to consult with your installer what bolts are necessary depending on the wall/ ceiling surface. 4. Using a drill, drill four (4) holes for the bolts. Mount the Mounting box on the wall/ceiling. Note: If your camera model includes the inner box inside the Mounting Box, make sure the cab ...