Canon PIXMA MP620 series Getting Started

Getting Started =Read Me First= Make sure to read this manual before using the machine. Please keep it in hand for future reference. 1111111111111111111111111111111111111111 QT51692VOI

A ~ ~ Instructions that, if ignored, could result in personal injury or material damage. Instructions that must be observed for safe operation. Additional explanations. Descriptions for operations that take some time to complete. • Microsoft is a registered trademark of Microsoft Corporation. • Windows is a trademark or registered trademark of Microsoft Corporation in the U.S. and/or other countries. • Windows Vista is a trademark or registered trademark of Microsoft Corporation in the U.S. and/or other countries. • Macintosh, Mac, and AirPort are trademarks of Apple Inc., registered in the U.S. and other countries. • Wi-Fi is a registered trademark of the Wi-Fi Alliance. The Wi-Fi CERTIFIED logo is a certification mark of the Wi-Fi Alliance. Model Number: K10325(MP620)

Turn the Power On Install the Print Head Install the Ink Tanks Confirming the Setup Flow Setup the Machine and the Computer B Loading Paper After Installing the Machine

Open the Paper Output Tray with your hands, and take out the Print Head. • Manuals • Setup CD-ROM (containing the drivers, applications and on-screen manuals) • Warranty • Before turning on the machine, remove all the orange tapes and the protective sheets. • A USB cable is necessary to connect the machine with your computer.

and set the ink tank. Plug in the power cord on the left side at the back of the machine and connect the other end to the wall outlet. Open the Operation Panel (A), then press the ON button (8) to turn on the machine. Use the'" or .. button (D) on the Operation Panel to select the language for the LCD, then press the OK button. The standby screen is displayed. Do NOT connect the USB cable at this stage. • Make sure that the Document Cover (C) is closed. • If an unintended language is displayed on the LCD, press the Back button on the Operation Panel to return to the Language selection screen. r=:r:=l ~ • The machine may make some operating noises. This is normal operation.

Scanning Unit (Cover) (B) until it locks into place. A Raise the Print Head Lock Lever (E). (8) (A) The Scanning Unit (Cover) (8) is fixed automatically. The Print Head Holder (C) comes out. (This is where you install the Print Head.) o A A • Close the Document Cover (D) and lift it with the Scanning Unit (Cover). • Firmly raise the Print Head Lock Lever until it stops. (The Print Head Lock Lever may feel heavy.) • Do not handle the Print Head roughly such as applying them excessive pressure or dropping them. ~ ~ • The Print Head Holder makes a noise as it moves. This is normal operation. ~ ~ If the Print Head Holder does not move, make sure that the machine is turned on.

silver package. Remove and discard the orange protective cap. Tilt the Print Head and set it in place. Lower the Print Head Lock Lever (E) completely. A • There may be some transparent or light blue ink on the inside of the bag the Print Head comes in, or the inside of the protective cap - this has no effect on print quality. Be careful not to get ink on yourself when handling these items. Be careful not to stain your hands. A • Do not knock the Print Head against the sides of the Holder. • Be sure to install it in a well-lit environment. • Pinch the Print Head Lock Lever firmly and lower it gently. • Once you have installed the Print Head, do not remove it unnecessarily.

roughly such as applying them excessive pressure or dropping them. • If the Print Head Holder moves to the right, close and reopen the Scanning Unit (Cover). • Be sure to use the supplied ink tanks. o (2) Pull the orange tape (1) in the direction of the arrow to peel off the protective film and remove the film (2) completely. While pressing down with your left thumb, twist off the orange protective cap (A) located on the bottom of the ink tank. A • Do not hold the sides of the ink tank; ink may splash.

y y Press the PUSH mark on the ink tank until it clicks into place. Make sure the Ink lamp lights red. A • Be sure to install it in a well-lit environment. • Match the labels when installing. Install all the other ink tanks in the same way. Install all the ink tanks. A • Once you have installed the ink tanks, do not remove them unnecessarily. • Make sure all the Ink lamp lights red. Load plain paper in the cassette and press ma. Close the Scanning Unit (Cover) (8). • Wait until the screen above appears (about 4 minutes) and go to the next step. The machine may make some operating noises when preparing to print. This is normal operation. ~ a;;;j,;;I • If an error message is displayed on the LCD, make sure that the Print Head and the ink tanks are correctly installed.

paper into the Cassette (C), then press the OK button. Head alignment is recommended if you print photos. No head ali nment ~e.d alignment Press the OK button. Confirm that the above screen appears. 1Remaining ink volO Introduction ~ I;;j;;,I For details, refer to "21 Loading Paper" on page 56. • Close the Paper Output Tray to make it easier to pull out the Cassette. ~ I;;j;;,I • For better print results, it is recommended that you align the Print Head before printing photos. To align the Print Head, use the'" or • button to select Perform head alignment, then press the OK button. Follow the steps in "Align the Print Head" on page 67 for alignment. • You can perform Print Head Alignment at any time. For details, refer to the on-screen manual: Basic Guide.

Before starting setup, decide on the most suitable connection method for the machine. This machine can be used over a wireless or wired LAN, as well as via USB connection. ~ USB rio Wired LAN .. .. . . .".. ('E') Wireless LAN •...•..••••••....•............• ~ ~'III)(([~ Access point J) 1/ 1/(, mo • Before connecting the machine to the network, confirm that configuration of the computer and network devices (router, access point, etc.) is complete, and that the computer can connect to the network. For the procedures to connect a network device to the computer and set them up, refer to the manual of your network device or contact its manufacturer. • The machine cannot be used over a wired and wireless LAN at the same time.

To use the machine by connecting it to a computer, software including the drivers needs to be copied (installed) to the computer's hard disk, and setting configured according to the connection method. In addition, configure the machine's LAN settings to connect to the network. Read the following carefully before starting setup. The screens below are based on Windows Vista operating system Ultimate Edition (hereafter referred to as "Windows Vista") and Mac as x v.1 O.5.x. o Notes on Setup Quit all running applications before installation. Log into a user account with the administrator privilege. Do not switch user accounts during installation. • It may be necessary to restart your computer during the installation process. Follow the on-screen instructions and click OK, and do not remove the Setup CO- RaM during restarting. The installation resumes from where it left off when your computer has been restarted. • Since Mac as 9, Mac as x Classic environments, Mac as x v.10.3.8 or earlier are not supported. o Notes on Network Connection • Before connecting the machine to the network, confirm that configuration of the computer and network devices (router, access point, etc.) complete, and that the computer can connect to the network. • For information on how to confirm the settings of the access point, refer to your access point's instruction manual or contact its manufacturer. For example, - Disable Stealth (closed network) function - Confirm MAC address - Disable the access point's IP address • The configuration, router functions, setup procedures and security functions of the network device vary depending on your environment. For details, refer to your device's instruction manual or contact its manufacturer. • If the firewall function of your security software is turned on the warning message may appear that Canon software is attempting to access the network. If the warning message appears, set the security software to always allow access. • In an office setup, consult your network administrator. If a screen not specified in the procedure or an error message appears during setup, refer to "5 The following screen is displayed during setup" in the printed manual: Network Setup Troubleshooting. o Note on Wired LAN Connection • A router and LAN cable are required to connect the machine to a wired LAN. These must be purchased separately. o Notes on Wireless LAN Connection Ad-hoc mode is not supported. If you connect to a network that is not protected with security measures, there is a risk of disclosing data such as your personal information to a third party. • The machine may communicate with other access points used in the vicinity. • The machine supports WPS (Wi-Fi Protected Setup) and WCN (Windows Connect Now) in addition to the conventional wireless LAN settings. As for WCN, "WCN-UFO" that requires a USB flash drive is supported.

USB USB ~ 7 8 12 (P.13) (P.16) (P29) Which connection method do you intend to use? 13 (P.32) 14 (P.37) 18 (PAS) Network Wired LAN Is this your first time Yes cPo Wlmmm 6 (P.12) 7 (P.13) 9 (P.17) 12 (P29) connecting the machine to the network? M 6 (P.12) 13 (P.32) 15 (P.38) 18 (PAS) No ~ 'III) (({Id ('E') {tf1rmrma 6 (P.12) 7 (P.13) 10 (P.21) 12 (P.29) M 6 (P.12) 13 (P.32) 16 (PAD) 18 (PAS) Wireless LAN WPS Wlmmm 19 (PA8) 7 (P.13) 11 (P26) 12 (P.29) M 19 (PA8) 13 (P.32) 17 (PA4) 18 (PAS) WeN Wlr:mm 20 (P.S1) 7 (P.13) 11 (P.26) 12 (P.29) To set up an additional computer Wlmmm 7 (P.13) 11 (P.26) 12 (P.29) 13 (P.32) 17 (PA4) 18 (PAS)

o (A) e Wireless LAN active Wired LAN active 7 (P.13) 73 (P.32) ,,;t Change wireless/wired Select either to the connection method, then press the OK button. Windows WSO setting ResetLANs~ Change wireless/wired Wireless LAN settings Wireless LAN setting list Wired LAN setting list IPv4/1Pv6setting if LAN settings Select Change wireless/wired, then press the OK button. Advanced settings PictBridge print settings language selection - Reset setting Macintosh Plain paper feed settings Print settings LAN settings ~t Device settings Select LAN settings, then press the OK button. Next, read "Install the Software" ! .i§.lill - Device settings 2/3 Perform various settings. &I Settings Select Device settings, then press the OK button. ~ .- ~ ~ Settings d iAemaining ink yoU Introduction Use the Easy-Scroll Wheel (A) or the ~ or ~ button to select Settings, then press the OK button.

Go to Step O. Windows Vista Windows XPI 2000 Windows ,,--- • If the program does not start automatically, double-click the CO- ROM icon on the computer. When the CD-ROM contents appear, double-click MSETUP4.EXE. Turn on the computer, then insert the Setup CD-ROM into the CD-ROM drive. The setup program should run automatically. ~ 1;;1;:1 • Operating noise continues for about 30 seconds until the machine turns off. Make sure that the POWER lamp (B) stops flashing. Press the ON button (A) to TURN OFF THE MACHINE. Setup the Machine and the Computer " locate and install driver software (recommended) W,ndows wdl9\llde you thfouqh ~ proc~ of mstallill9 drlY6 soft~rf fOfyov

PIXMA MP620 series canon • If you want to select particular items to install, click Custom Install and follow the on-screen instructions to proceed with the installation. Click Easy Install. The drivers, application software, and on-screen manuals are installed automatically. ' .... u'''9'.'''~''''""- r~ ~=~~""(O-FOf..' User Account Control screen appears, click Continue. If the same screen reappears in subsequent steps, click Continue. o Windows Vista OVO,CD·I\W Dn e £.1 (.'NO!'.)J AutoPlay screen appears, click Run Msetup4.exe. e Windows Vista

10(P.21) I Additional 1 1 (P.26) Computer fI WPS 11 (P.26) I WCN 11 (P.26) Go to either of the following procedures according to your connection method! ,..".Iut"'Sol: ... I',tJ:E YOO~~ tOIlE BO'..lIll9Yn£ ._~,.\S()f'.~~~IT_F)'~_~~l~f.~NI"EQ.lS_ 1J"JU8(cep(lIle~lNlfIlHlI ~'ck('l'i1S) IYOUCld[No] \N!wrwarl ~.)I\,..I~(llro:el$1 License Agreement Canon Producis Berore'nslatill!lCanooPr0Wct5 care/utfl'llltjlll8lceme 1!PI~beIow • Follow anyon-screen instructions to install the software. Read the License Agreement screen carefully and click Yes. Installation starts. Easy Install Click Install. Move the cursor over items to display explanations.

Windows Next, read "12 Information" on page 29! ----r-----------, • The USB port is located on the right side at the back of the machine. • When the machine is recognized by the computer, a message appears on the screen. • If you cannot go to the next procedure after 10 minutes, click Help and confirm the message. When the Printer Connection screen appears, connect the machine to the computer with a USB cable, then turn on the machine. ~ I;;j;;,I Pnnr..... • M ..d<1oI~:.. ~to!lit! ""_ .Jr ;;~~~C~~:_'~I,,~::=~ S&;ocll1'l5opu~III&:'_...r

e Prepare Cables C P"',*,salfeadtcomectedto!llel'llltWl)l1. ~~" ~lthls<»b""wh8n'fOU__ lOuseapnl'l"lI\,JI[ls ~. =~~:O~~~~:~~e< ~~lI$Ir.gWPS('M.FIPfCWCb:ldSelup)orWCN C/YI~C_tNowI '""... lMlIl&pnrter";JUS8 ~ s-:tltlS~OOIOUS8thepnlEllr"'lIlJS8 Setup Method SvlectIll&5Mlpmaltlod.lIlIdth8llclck[NMJ Setup the Machine and the Computer • Set the machine's LAN setting to Wired LAN active beforehand. For details, refer to "6 Machine's LAN Setting" on page 12. On the Setup Method screen, select Connect printer to the network for the first time, then click Next. When a confirmation screen for the machine's LAN setting appears, click OK. o

confirm that preparation is complete, then click Next. ~~~ USB • The machine is recognized by the computer, then message appears on the screen. • If you cannot go to the next procedure after 10 minutes, click Help and confirm the message. • The USB port is located on the right side at the back of the machine. When the Printer Connection screen appears, connect the machine to the computer with a USB cable, then turn on the machine. Set up the machine over a USB connection until the network connection is complete.

The~f\"""""""«Md"t..diIlocled~ S"'lholPoldIHuolhl".........be~ Windows XP/2000 If no connection is established even after Connect is clicked, refer to "5.6 The Set Printer IP Address dialog box is displayed during setup" in the printed manual: Network Setup Troubleshooting. When the Set Printer IP Address screen appears, click Connect. If the machine is detected automatically, the Set Printer IP Address screen does not appear. Go to the following procedure. Windows Vista Go to Step O. ~ ~ e Detect the Machine Connect the machine to the network device with a LAN cable (A), then click Yes. (A) ~ USB

~ USB To change the port name, click View Setup Results, then click Set Port Name. For details, refer to "8 Changing the port name" in the printed manual: Network Setup Troubleshooting. • If Unsafe Removal of Device is displayed, click OK. When the Setup Completion dialog box appears, remove the USB cable, then click Finish. ~... ~..~ol

• If you cannot go to the next procedure after 10 minutes, click Help and confirm the message. • The USB port is located on the right side at the back of the machine. Set up the machine over a USB connection until the network connection is complete. When the Printer Connection screen appears, connect the machine to the computer with a USB cable, then turn on the machine. ~ ~ e Setup the Machine and the Computer • Set the machine's LAN setting to Wireless LAN active beforehand. For details, refer to "6 Machine's LAN Setting" on page 12. When a confirmation screen for the machine's LAN setting appears, click OK. On the Setup Method screen, select Connect printer to the network for the first time, then click Next. o

dialog box appears, confirm that preparation is complete, then click Next. o Detect Access Point .... When the Access Points screen appears, select an access point to use, then click Connect. When an access point is detected automatically, the Access Points screen does not appear. Go to step O. To connect to the access point with WEP or WPA displayed in the Encryption column, enter the network key (WEP key or WPA key) in Network Key, then click Connect. For details on network keys, refer to "3.1 About Network Key (Windows)/ Network Password (Macintosh)" in the printed manual: Network Setup Troubleshooting. r=:r:=t ~ If you want to select an access point manually, or if the target access point is not displayed in the list, or if an error message appears, refer to "5 The following screen is displayed during setup" in the printed manual: Network Setup Troubleshooting.

SI*'I1h...... no:kt.\NnI~ • If the error message appears, refer to "5 The following screen is displayed during setup" in the printed manual: Network Setup Troubleshooting. When the Network Setup of the Card Slot dialog box appears, specify the drive letter, then click Next. ~ ~ e Windows XP/2000 Go to Step O. Go to Step O. Windows Vista Windows XP/2000 If no connection is established even after Connect is clicked, refer to "5.6 The Set Printer IP Address dialog box is displayed during setup" in the printed manual: Network Setup Troubleshooting. When the Set Printer IP Address screen appears, click Connect. If the machine is detected automatically, the Set Printer IP Address screen does not appear. Go to the following procedure. ~ ~ e Detect the Machine

then click Next. Turn off the machine, then place the machine in the location where you will use it, and turn on it. () ~~~ USB To change the port name, click View Setup Results, then click Set Port Name. For details, refer to "8 Changing the port name" in the printed manual: Network Setup Troubleshooting. If Unsafe Removal of Device is displayed, click OK.

• If any symbol other than 0 is displayed, refer to displayed comments and Help for improving the status of communication link. • To check whether the new location is better, click Remesurement. Measurement of the communication status is performed again. • When any message on Overall network performance appears in the measurement results, rearrange the printer and other network devices following the instructions on the screen. Confirm the measurement results, then click Finish. Ensure that 0 is displayed in Connection performance between the printer and the access point. ~ ~ M.......to.CIIIod"""'"*IO_..~~ f'(OU"''*''*..__...... ..-...nlllOCll'Mll -- ""'-.. _~._,IIl- ..IIIJ'f*'..... IO.. _ fl(W(...:I_..n.l_~~__ I'l;a~ ~"'c.-"""'~IIIod!.""~ • Measuring takes a few minutes. You can cancel measuring by clicking Cancel. You also examine the detailed status of the communication link after setup by using the Canon IJ Network Tool. For details, refer to the on-screen manual: Advanced Guide. On the Connection Performance Measurement screen, click Next. Measuring of the communication status starts, and the results are displayed. ~ ~

-.i ~m.S<)pG')I'I[;;.usell>tP·Ht"''''lllJjE' (i:Pl't!'ll,'S '~a<1y_':JMfo:~IAlt>e~ ~llh.. otJCI(lIl_J'OIIWllr(lOusea;;;I'll~1Ml"" iJI~e~" l'rom'f'Oll'WITllul'!l' ~tl!llse>ptlonal5o_w,r~lMI";r;~ 581~U"'no;lVvPSfWo_FPr~~ ,Wlj rWtI\OoJw',(ot'N(lN.)oo. Setup the Machine and the Computer (A)-+II--fm o Press the ON button (A) to TURN ON THE MACHINE. • Make sure that the computer you are setting up is not connected to the machine with a USB cable. For wired LAN connections, confirm that the machine is connected to the network with a LAN cable. On the Setup Method screen, select Printer is already connected to the network, then click Next.

Go to Step O. Go to Step 0. Windows Vista Windows XP/2000 [ ... v;;;;;' .....lIobt..... -.6lllCltbt~ct.o.tIoll... .-..~ ..__hr--.II-...I...........dclJJ!>d*!O<.• ,1tdjlD Ml ...... _~_IJSllJall:w,n;j... __..... When the machine is not detected, make sure of the following, click Update. - The machine is turned on. - When using wireless LAN: The computer is connected to the access point. - When using wired LAN: The machine is connected to the network device with the LAN cable. • Some programs that switch the network environment depending on your environment will enable a firewall by default. Check the settings of any such software. ~ Q:I e

letter, then click Next. When the Setup Complete screen appears, click Finish. ~ ~ If the error message appears, refer to "5 The following screen is displayed during setup" in the printed manual: Network Setup Troubleshooting. ~ ~ • To change the port name, click View Setup Results, then click Set Port Name. For details, refer to "8 Changing the port name" in the printed manual: Network Setup Troubleshooting. Next, read "12 Information" on page 29!

fIipl!\(,or:Mldp!l(1,:,P'Jpeft'll('!Ilt>r8¥ ". Setup the Machine and the Computer Load plain paper Into the cassette • For details, refer to "21 Loading Paper" on page 56. o When the Load plain paper into the cassette screen appears, load plain paper in the Cassette (A) and click Next. ~...

_ ... P' ' nd'" ...._ When the Extended Survey Program screen appears, confirm the message. If you can agree,click Agree. If you click Do not agree, the Extended Survey Program will not be installed. (This has no effect on the machine's functionality. ) o • Internet connection is required. (Connection fees apply.) User RegIstration • To register later, click Cancel. User Registration can be started from the Solution Menu icon. For details, refer to "Solution Menu" on page 60. Click Next. If connected to the Internet, the user registration page appears. Follow the on-screen instructions to register your product. You will need your product serial number, which is located on the inside of the machine.

Next, read "21 Loading Paper" on page 56! J) Exit ( Click Exit. If Restart is displayed, make sure that the Restart the system now (recommended) check box is selected, then click Restart. After restarting the computer, remove the Setup CO-ROM and keep it in a safe place.

If the CD-ROM folder does not open automatically, double-click the CANON_IJ icon on the desktop. e Turn on the computer, then insert the Setup CD-ROM into the CD-ROM drive. Setup the Machine and the Computer • When connecting an additional computer, make sure that the machine is turned on, then go to step e. It is not necessary to connect the machine to the computer with a USB cable. • The USB port is located on the right side at the back of the machine. Connect one end of the USB cable to the computer and the other to the machine. Make sure the machine is turned on. o

the on-screen instructions to proceed with the installation. Click Easy Install. The drivers, application software, and on-screen manuals are installed automatically. ~ a;;j;;I If you do not know your administrator name or password, click Help, then follow the on-screen instructions. Enter your administrator name and password. Click OK.

load plain paper in the Cassette (A) and click Next. • For details, refer to "21 Loading Paper" on page 56. sa ~ lktoIwin";llfIlIlrMMI«*l"""'.~Il'Ol1f';"",.~11...cl "'IQnlMl~!\l1>ooklw ...... ..........ea-.." '-"'11"_'" _.3'N_,,-.o..-.. r_,...-,.- n;..-, __.,.. _ __ """__ _""'.. ' _...,."'"~l 1IY ..II'I.o.w.t.aTM£!lI'Jl'lWUlI!'I'O>/Q!E£TOl£lIOJNt\.,...l>'IET'£_ OFrn15~''''I'OUOONO'T_TOnoE~¢F~ _UMf....T~yCLOSl"~l'iSr lD< ...~ IUC.. CA&lltI!_'"fI[M.l.""'II!N!P [ll ...'IOOOU .......c 'I[~ _rfOUIil'fT ..... _ .. - ...-<""1' .. _ ..........",,_....-. ... ~_...-::epl~_l_[Y.-lyo.Jl:icIIlNo~""""""" .,__uc.-. (~).....J.LJ • Follow anyon-screen instructions to install the software. .,~'" J Read the License Agreement screen carefully and click Yes. Installation starts. Ot... _ I 1 ) ~ M I__ r........,._._1ofB ~hREAPMt:.!:J ~,.EaIr'~EX ~: _ c....... u....-..rVQl Click Install. Move the cursor over items to display explanations.

• To register later, click Cancel. User Registration can be started from the Solution Menu icon. For details, refer to "Solution Menu" on page 60. Click Next. If connected to the Internet, the user registration page appears. Follow the on-screen instructions to register your product. You will need your product serial number, which is located on the inside of the machine. ~ ~ T1'la-.p~~ ""'1"ld..c:t~_~D'" ClOd! [NeldlDpl'OllMdlD"l'Ibl~ Click Next.

procedures according to your connection method! J] ( fOl~"""LAH ...... IIl'O""''''~''''~l.AN''''Ilon''' lltI..... Ol*dOnpolllOtl~Q...~ ~,ddl~/MlworIl:-'O_wl OI~... -mrtng)'OUroon'lPJ'" fnol.....,Y'I'I,mtrlD... GelIIngSlaIliIl4 When using Mac OS X v.1 0.3.9, before using the Operation Panel on the machine to save scanned originals to the computer, it is necessary to select MP Navigator EX as the launch application on Image Capture under Applications. For details, refer to "Saving Scanned Data to PC Using the Operation Panel of the Machine" in "Scanning" in the on-screen manual: Advanced Guide. Click Restart. When the computer restarts, Canon IJ Network Tool starts automatically. Click Restart to restart the computer. After restarting the computer, remove the Setup CD-ROM and keep it in a safe place. 'I I

go to step 0! . (e- (t Q( }) e.-_. setup the Machine and the Computer If 'fO1... to \1M !.he pntlttl' ....11.. « US. COI'Il\«dotl, tde

dlck fCaJ 'I 'fO"~IO(-.am.:wv>_""'.llSIabor ..... ' """'I'tl\etl'la' brtl<.ft""for ... ...--c.etoclt(JqvoIU'f""~rl_..u·or_. • If no printer is detected, click OK. Make sure of the following, then click Update. - The machine is connected to the computer with a USB cable. - The machine is turned on. To set up a machine that is not yet connected to a LAN, connect to it by USB. Select Setup in the pop-up menu, select MP620 series in Printers, then click OK. ~ ~ e S.lup,"paraU<»l1 ='="'~lI_ust.._n>Kft,...._ l'Jot_...... --. ::::::-~=..-s If the Setup Preparations dialog box appears, confirm that preparation is complete, then click OK. e Setup the Machine and the Computer Set the machine's LAN setting to Wired LAN active beforehand. For details, refer to "6 Machine's LAN Setting" on page 12. SeieaI,",~O'I~ar-. .. thtJCOI"flUII'."lItn.Pf1I'W ,f't'l)ll oJ,Itn 10 1>'1 u.. p. toI:'«t {USI (OIltlK1Xllll. and th4!,,- dll;fE[()(J."The,,,,pWllllMtornplete IfYOlol IlIIJ1 10111"'" ~... wil'" ,aLAN~."~fl.,tJ.l (llOl~~lonJ..1Id tile", did!. (Ok) 1M", coro~..,.1M printer ~ ~Ittgs. On the Canon IJ Network Tool screen, select LAN connection, then click OK.

Hc..p h&J -.. IC/lIIMplrud 0!K:l)rl..en tht USI ~ dw COI'nKU 1"- printer &lid U. CO/l\Jk4'" Uld dod: lOICl. A priftteo' ~ ~!tM_ d,~ box

• ~ I ~ c.or-- Seleatlwpo_\'Oll_IOMtlollfoo'tfw.-'.af'ldtNftctIdl{(Jlq.If ycIU ..... toconr>«ttlM~wIdl.USlUIbIot.IIM.. ptnwltYlhlll .... l'f!l4tfottM~ckt"fo9'ltr'''''4't lIldidd.""".. ( ....-'""'- ) - • If no machine is detected, refer to "4.1 The machine is not detected" in the printed manual: Network Setup Troubleshooting. Make sure there is no problem, then click Update. Select Setup in the pop-up menu, select MP620 series in Printers, then click OK. ~ ~ e s.wp ".par.llona ................. I/.'_UIl.pOUM _ --~ ~=~=~ n.1olSIc*'. ~ If the Setup Preparations dialog box appears, confirm that preparation is complete, then click OK. SoeIIICt('"'COlIII«tIOl'l....u.od~It"thos~pufer."Iltt..prinlltf tf J'Ol,l pLln 10 11M 1M print.......ttl. USI COI\!'l4tCbOll, laItct {\lSI «>n~),.nd1M" clk\ [()I(J. Thot .fl"p .....1f be t_le~ tfvou cta/lIO 11M rite prlm:«YritllalNol cotlOKtlOft. NoMa fl.tJ,l COOlNCtIonI and thelldJdl!O(] TN... ~~\K.I,-~_lr; KttJrl'J$ • Set the machine's LAN setting to Wireless LAN active beforehand. For details, refer to "6 Machine's LAN Setting" on page 12. On the Canon IJ Network Tool screen, select LAN connection, then click OK. o

The 'o:A:owI"".Uti, iIIO'''''-. dflKa.d. Sel«:ttt>e~Jpotr1C~eotN't«to,• .,.,tlid<~11 -::~~~~ lot\!I,.au POOl'll, ~Ilaf tIM ~ ~~_d••!lId lh

THE MACHINE, then place the machine in the location where you will use it, and turn on it. (A) -+1+---4l!l1 o '"'-UlO"I""litrMfUP .... beencOfftCl'lolted TII"\oIfr~pnl'I[.'.di.-;: fl'"IJS.~ItW.

Mac as x V.1 O.S.X Mac as x v.1 OA.x/v.1 0.3.9 Next, read "18 Add the Machine" on page 45! • If any symbol other than 0 is displayed, refer to displayed comments and Help for improving the status of communication link. • To check whether the new location is better, click Remeasurement. Measurement of the communication status is performed again. • When any message on Overall network performance appears in the measurement results, rearrange the printer and other network devices following the instructions on the screen. ~ ~ __•••••• .Il.lla.lll~~~.lill .... 0""", Confirm the measurement results, then click Finish. The Printer Setup Utility and Canon IJ Network Scanner Selector will start up. Ensure that 0 is displayed in Connection performance between the printer and the access point. Th'1 WlUtd wtl mltUU,t tM<_tIOn jM-fonn.,flClI bl!~~tlM pnftltl &tid tIM KUU pocnt,.""dI~,~r,til ",1t:I~ lOf prinl'~ CMcIt tIw I,", pnntU'1 W....ed on..'Id dit;tt j/llU," """'n tblCOf\fMICtiotwIlIII'ffO'lftAfIU" PlllN'. p!«t tIM pt\I'W closer. rht KCflS poom"nt_ al'¥olI,KUollmwf ,*- - flooo"~~ talHl'IIJuWlope__ b..ctIa W-PO'll:"'$l -It ..... yllt;l 0:00.," of"'"''''lt1to'''U$OI'ttDll (Gfl~ ..-. (You un anctl!he 0Il'l1£>Cln whH tile ....'""nt~"".. III progftU.) • The c.u.on 1l Ntlw(>r\l; Tool .IJO .11Qw~ you 10 ....Uu.. 1M wnMdiooperfuml",,

Macintosh Go to Step E). canul s.tllp s...o(J/1l>e1O"_'I._~td :=:~~':~.~i~:"'""':QOo«l IUSI u,n.-.(lfll• .ttd ,,,-... dKk {0ICl Tften. (OIlflg..rflIM pnN..- ne--'r. ntti"9' On the Canon IJ Network Tool screen, select LAN connection, then click OK. o

series is the machine's MAC address. If the machine has not been detected, make sure of the following. - The machine is turned on. - The firewall function of any security soft- ware is turned off. - Wired LAN Connection: The machine is connected to the network device with the LAN cable. - Wireless LAN Connection: The computer is connected to the access point. - The machine is not set to use access control (MAC address filtering). Go to Step 0. Go to Step O. Mac as x v.10.5.x Mac as x v.1 O.4.X Wait for a while, then select Canon MP620 series and click Add. In Mac as x v.1 O.4.x, click More Printers in the Printer Browser screen. e Mac as x v.1 O.5.x/v.1 O.4.x Cl Go to Step e. Go to Step O. Setup the Machine and the Computer l'rinltrUsl =----'~--....--,.;r.l~:-~.iol--- CIononMP620nrlu Mac as x v.1 0.3.9 Mac as x v.1 O.4.X When the Printer List screen appears, click Add. o Mac as x v.10A.x/v.10.3.9

Confirm that your MP620 series is added to the list of printers. • The alphanumeric string after Canon MP620 series is the machine's MAC address. If the machine has not been detected, make sure of the following. - The machine is turned on. - The firewall function of any security software is turned off. - Wired LAN Connection: The machine is connected to the network device with the LAN cable. - Wireless LAN Connection: The computer is connected to the access point. - The machine is not set to use access control (MAC address filtering). Select Canon IJ Network in the pop-up menu, select your machine's name in the list of printers, then click Add. ~ Q;;I e Mac OS X v.10.4.x/v.10.3.9

Paper" on page 56! lWAJH o.w. Souf1:" Hal'l"lll ca:;;,;;;;u"'20Mtl'f1,~k Confirm that a check mark is displayed, then click Exit to close the dialog box. • To confirm the machine's MAC address, refer to "Troubleshooting" in the on-screen manual: Advanced Guide available via Solution Menu. • With Mac as x v.1 a.s.x, the Card Slot is not available when using the machine over a network. On the Canon IJ Network Scanner Selector screen, select Canon MP620 series Network in TWAIN Data Source Name and the MAC address of the machine in Network Device List, then click Apply to use the machine as a scanner. ( c._ Mf'&20-,",.-f - 3l) N.twori< Deo<,e" llJl

Language selection Reset se~9_ _ __ ~ Device settings Plain paper feed settings Print settings LAN ,etling, Select LAN settings, then press the OK button. -.f§.lli '-----J Device settings 2/3 Perform various settings. 1M Settings Select Device settings, then press the OK button. e ~ •• ~ ~ Settings <:t ~Remainjng ink YOID Introduction (A) Use the Easy-Scroll Wheel (A) or the

Chenge wireless/wired Wireless LAN settings Wireless LAN setting list Wired LAN setting list IPv4/lPv6 setting WSD setting Reset LAN setiTr19s-- Select Change wireless! wired, then press the OK button. ~~ Change wireless/wired Wireless LAN active Wired LAN active Select Wireless LAN active, then press the OK button. lit LAN settings Change wireless/wired Wireless LAN settings Wireless LAN setting list Wired LAN setting -Iis-t-- IPv4/lPv6 setting WSD setting Reset LANsettings Select Wireless LAN settings, then press the OK button. IiJ\Wireless LAN settings WPS setting WCN setting'-- _ Select WPS settings, then press the OK button.

Push button method PIN method lit Push button method Connect to a wireless LAN access point supporting the WPS push button method. Next 'i'~, Push button method Prepare a wireless LAN access point. For details, see the access point manual. When ready, press 1!13 of the device. Start connection Following IS completed. WPS setting Macintosh Windows Next, read "Install the Software" ! • A timeout error occurs if setup is not completed within two minutes. When the timeout error screen appears, refer to "5.12 The Timeout error screen is displayed during WPS setup" in the printed manual: Network Setup Troubleshooting. • The WPS button may be named differently depending on your access point. For details, refer to the manual of your access point. The completion screen appears on the LCD of the machine, then the LAN settings screen returns. When the access point is ready, press the OK button on the machine, then press the WPS button on the access point within two minutes. ~ t;;J;;I Press the OK button. To use the PIN code method for setup, select PIN method on step 0, then press the OK button. Follow the on-screen is instructions to operate the machine and access point. When the setup is complete, the completion screen appears then the LAN settings screen returns. A timeout error occurs if setup is not completed within 10 minutes. If the timeout error screen appears, refer to "5.12 The Timeout error screen is displayed during WPS setup" in the printed manual: Network Setup Troubleshooting. Select Push button method, then press the OK button. ~ t;;J;;I

The Add a wireless device to the Network screen will be displayed. I"'· ,.,,, 1.-....... • From the Start menu of the Windows side, click Network. The Network folder opens. o Setup the Machine and the Computer Canon assumes no responsibility for any damage or loss of stored data regardless of the cause. If your USB flash drive cannot be attached to the direct print port of the machine, an extension cord for USB flash drives may be required. Purchase one at an electronics shop. • Operation may not be guaranteed depending on your USB flash drive. • USB flash drives with security enabled may not be used. • The machine supports "WCN-UFD". You can set the wireless LAN security on the machine easily by using the WCN (Windows Connect Now) function of Windows Vista together with a USB flash drive. . 51

computer that is not on the list, using a USB flash drive. Click Add the device or computer using a USB flash drive. From the list, select the network name (SSID), then click Next. ~ I;;;j;;,I • If the User Account Control screen appears, click Continue. If the same screen reappears in subsequent steps, click Continue.

from the computer, then click Close. _. -=-=------1 o Connect the USB flash drive to the computer, confirm that the drive name is displayed, then click Next.

Introduction Use the Easy-Scroll Wheel (A) or the ~ or • button to select Settings, then press the OK button. Settmgs ~ I~r ~ Device settings 2/3 Perform various settings Select Device settings, then press the OK button. Device settings Plain paper feed settmgs Print settings LAN settlOgs Advanced settings PictBridge print settings Language selection Reset setting Select LAN settings, then press the OK button. t LAN settIngs Change wirelessjwtred Wireless LAN settings Wireless LAN setting list Wired LAN setting list IPv4/IPv6 setting WSD setting Reset LAN settings Select Change wireless! wired, then press the OK button.

The completion screen appears on the LCD of the machine, then the LAN settings screen returns. Remove the USB flash drive from the machine. Connect the USB flash drive to the direct print port (USB connector) on the front of the machine, then press the OK button. ~ing is completed.- WCN setting Connect the USB flash drive on which you have saved the network information with the WCN setting. ~~e~e~~~~hed. press r!13 of I (,l WCN setting WPS setting WeN setting it Wireless LAN settings Select WeN settings, then press the OK button. LAN settings Change wireless/wired Wireless LAN settings Wireless LAN setting list Wired LAN setting list IPv4/1Pv6 setting WSO setting Reset LAN settings Select Wireless LAN settings, then press the OK button. Wireless LAN active Wired LAN active r~ Change wireless/wired Select Wireless LAN active, then press the OK button.

load paper in the Cassette (A) and the Rear Tray (B). o Load in the Cassette (F) e Load paper. ~--(E) Move the Paper Guides (E) and (F) to both edges. Pull out the Cassette (A). (D) The Cassette (A) supports plain paper (C) only. To print Photo Paper / Hagaki (D), be sure to load it in the Rear Tray (8). ~ ~ Load paper with the printing side facing down.

with the mark of paper size. The Paper Guide (E) will stop when it aligns with the corresponding mark of paper size. • There may be a little space between the Paper Guide (E) and the paper stack. Slide the Paper Guide (F) against left edge of the paper. Do not exceed the Load Limit Mark (G). A • To print on speciality paper, be sure to load it in the Rear Tray. Insert the Cassette (A) into the machine until it clicks into place.

Open the Paper Support (H) and pull it out. Move the Paper Guides (I) to both edges. Load paper in the center of the Rear Tray. Slide the left and right Paper Guides (I) against both edges of the paper. Do not exceed the Load Limit Mark (J ). ~ L;;;;!;;I Load paper in portrait orientation with the printing side facing up. • For details on media sizes and types you can use, refer to "Loading Paper" in the on-screen manual: Basic Guide. Machine installation is now complete!

procedures to make full use of the machine. Also includes "Troubleshooting" information for your machine. Basic Guide (on-screen manual) Describes the basic operations and gives an introduction to other functions available. Getting Started (this manual) Network Setup Troubleshooting Getting Started =Read Me First'" Describes how to set up and use your machine. Introduces the machine and its functions, the included manuals and application software. For proper use, read safety precautions before using the product. Safety Precautions Safety and Environment Information

Example: Windows Vista -'II One Click 10 Pilato PrlIlt Open various applications and on-screen manuals with a single click. You can start Solution Menu from the Solution Menu icon on the desktop (Windows) or on the Dock (Macintosh). ltoWtolbe"", Screea ~n1to"butonon!Mso:ear.tQOI$-pla,'I'letlu<':riptlonat~ilfhfWldjon TGU!ea~ l',ileltrlti (l)f(flipOl'\ti

This machine allows you to print in various ways using the MP driver and application software installed on the computer. For example, you can print borderless photos, and create your own calendar etc. easily. Also, you can scan documents into a computer, and correct/enhance scanned images. For detailed operating procedures and functions, refer to the on-screen manuals. (NOW let's use the machine! ) ..

For more information on printing from a memory card, refer to "Printing from a Memory Card" in the on-screen manual: Basic Guide. 0011/1ID> ""-------- (A) • Insert a memory card into the Card Slot in the direction of the arrow on the label, with the labeled side facing left. Insert only one memory card. • Press the HOME button (C) to return to the standby screen. o While the standby screen appears, open the Card Slot Cover (A), insert a memory card into the Card Slot, then close the Card Slot Cover (A). Confirm that the Access lamp (8) has lit up. After the photos on the memory card are read, the screen to specify photos and the number of copies to print appears. A CF~ ~I MS SO Duo MS o .. GJ .. []JJ ~ .. hC] w ------------------------ c:b ICiJ Memory Stick Micro Memory Stick Duo Memory Stick PRO Duo Memory Stick Memory Stick PRO SO Card SDHC Card MultiMediaCard (VerA.1) MultiMediaCard Plus (VerA. 1) RS-MMC (VerA.1) microSD Card microSDHC Card miniSD Card miniSDHC Card Compact Flash Card* Microdrive xO-Picture Card xD-Picture Card Type M xO-Picture Card Type H *Supported Memory Cards (Adapter required for .) -~ ·oo~ '"----------------.." 62 *TYPE II TYPE II (3.3V)

orientation. ~ I;;;j;;I • For details, refer to "21 Loading Paper" on page 56. Rotate the Easy-Scroll Wheel (E) to display a photo to print. Alternatively, use the ~ or ~ button to select a photo. 63

of copies, then press the OK button. The Print Settings Confirmation Screen appears. 64 Press the Color button (F). Printing will start. After printing, open the Card Slot Cover (A), pinch the memory card and pull it straight out, then close the Card Slot Cover (A). • Do not remove the memory card while the Access lamp (8) is flashing. Saved data may be damaged.

This section explains with Plain Paper. For various copying procedures, refer to "Copying" in the on-screen manual: Basic Guide. (E) (D) (C) (F) Close the Document Cover (A), press the HOME button (C), then press the Black button (D) twice for black & white copying, or the Color button (E) twice for color copying. Place the document face-down and align it with the Alignment Mark (8). Open the Document Cover (A). Load A4 or Letter-sized plain paper in the Cassette. o Copying will start. Remove the document after printing. ~ ~ • For details, refer to "21 Loading Paper" on page 56. • Do not place any objects weighing more than 4.4 Ib / 2.0 kg on the Platen Glass. Do not press or put weight on the original with pressure exceeding 4.4 Ib /2.0 kg. Doing so may cause the scanner to malfunction or the Platen Glass to break. • Do not open the Document Cover until copying is complete. ~.... Make sure that the Output Tray Extension (F) is extended. 65

This section explains how to print borderless photos using 4" x 6" size Photo Paper Plus Glossy II. The screens are based on Windows Vista. e J ........_- "'M • ......, ..._to *'I_;<1t...",_ --- CE)~O l,.lil;..;;:;,;:==-.... -_. * }.;::::::.~=~ ~:o---~ ffj =--_.-. o In Solution Menu, click One- Click to Photo Print. Easy-PhotoPrint EX starts. Select the image you want to print in a folder, then click Layout/Print. Load a sheet of photo paper in the Rear Tray (A) in portrait orientation. Load paper with the printing side facing up. Click Print. Printing will start. When a photo is selected, the number of copies is set to "1." r::r:=l &:;j,;:I For opening Solution Menu, refer to "Solution Menu" on page 60. For more information refer to the on-screen manual: Advanced Guide. r::r:=l &:;j,;:I • For details, refer to "21 Loading Paper" on page 56. r::r:=l &:;j,;:I On Macintosh, if the Print screen is displayed, click Print to start printing. 66

To cancel Print Head Alignment, press HOME button (A). (A) Use three sheets of A4 or Letter-sized plain paper for alignment. o IS¥:) Confirm that three or more sheets of A4 or Letter-sized plain paper are loaded into the Cassette (B). ~ 1+1 For details, refer to "21 Loading Paper" on page 56. 00 you want to print the print head alignment pattern? Set 3 sheets of paper. Ves I No===:=J (C) Select Yes, then press OK button. Printing of the first pattern starts. ~ 1+1 • Make sure that the Output Tray Extension (C) is extended. 67

the pattern with fewest streaks or stripes. 01/07 Fir Manual head More noticeable vertical white streaks More noticeable horizontal white streaks Less noticeable vertical white streaks Less noticeable horizontal white streaks I - Did the patterns print correctly? - I - :: - r -- 1 - Yes =- - = rJ71I!r I No I - - - - ,.-I-Dii?'T - e When the above pattern is printed, select Yes and press the OK button. Look at the first printout, and use the -4 ....... buttons to enter the number of the pattern that has the least noticeable vertical or horizontal streaks for columns A to G, then press the OK button. ~ ~ ~ ~ • The pattern is printed in blue and black. • If it is difficult to pick the best pattern, pick the setting that produces the least noticeable white streaks. 68

Ves I Less noticeable vertical white streaks More noticeable vertical white streaks !Ill Manual head align I Select the number of _J the pattern with fewest streaks or stripes. 01/10 ~ · ~ ·Jj • [ I !J Confirm the above message, then press the OK button. Printing of the second pattern starts. Follow the same procedure as 0 to enter the number of the pattern that has the least noticeable vertical streaks for columns H to Q, then press the OK button. 69

Introduction f ~ Manual head align I Select the number of I the pattern with fewest streaks or stripes. ·:·'i 01/10 a • ' b t c Less noticeable horizontal white stripes More noticeable horizontal white stripes Ves Continue. Press I!I3I when ready. Confirm the above message, then press the OK button. Printing of the third pattern starts. Enter the number of the pattern that has the least noticeable horizontal stripes for columns a to j, then press OK button. Confirm that the above screen appears. Print Head Alignment is now complete. ~ ~ • If it is difficult to pick the best pattern, pick the setting that produces the least noticeable white stripes. Print Head Alignment is now complete. Next, read "5 Confirming the Setup Flow" on page 9! 70

Email Tech Support - www.canontechsupport.com Toll-Free Live Tech Support- (1-800-828-4040) This option provides live telephone technical support, free of service charges, Monday-Friday (excluding holidays), during the warranty period. Telephone Device for the Deaf (TOO) support is available at (1-866-251-3752). Ordering Information The following ink tanks are compatible with this product. CU-2218K eU-221M ell·ll1Y PGI-220BK ell-2llC CLI-221 Black CLI-221 Magenta CLI-221 Yellow PGI-220 Black CLI-221 Cyan Order # 2946B001 2948B001 2949B001 2945B001 2947B001 Call 1-800-0K-CANON to locate a dealer near you, or visit the Canon eStore at www.canonestore.com www.usa.canon.com QT5-1692-V01 062008AN ©CANON INC.2008 PRINTED IN THAILAN[

Information on the following page in the Getting Started guide contains a mistake. Please refer to the screenshot below when installing the software on a Macintosh. Users In USA: Page 34 Step 0 Users In Australia, New Zealand and Asia: Page 34 Step 0 [Incorrect] Installation Ucense Agreement Before installing the selected software programs, carefully read the license agreement below. ATTENTION~PLEASE READ THIS DOCUMENT BEFORE INSTALLING THE SOFTWARE This i' a 1;C:e1\5e agreementb&tw&en yOu and Canon !I1C.• navillQ it~ place 01 b1J&lness a13O·2 Shimomaruk.o 3-<:home, Ot'Ita·kv, Tok.yo 14S-8S01.Japan ("Canon-I. with respeC110 the soltware and it! associated printed matetlal$ aM 'onlme' or eleettonicdocumentation, it llIny (c::oI~Ctively. the ·Software"j. r 1 I BY INSTALLING -mE SOF1WAAE YOU AGREE TO BE BOUND BY THE TERMS OF THts AGREEMENT. IF YOlJ DO NOT AGREE TO THE TERMS OF THIS AGREEMENT, PAOMPTLY CLOSE THIS INSTALLATION PROGRAM. IN SUCH CASE. THE SOFTWARE Will NOT BE INSTALLED AND YOU WILL HAVE NO RIGHT TO USE IT, , i Y

,,)f t", ~ >!0",./;; 0N. %! ;/ > This manual describes troubleshooting tips for problems you may encounter when setting up. ~.... • If you do not find a description for your trouble here, refer to "Troubleshooting" in the on-screen manual: Basic Guide/Advanced Guide. • Troubles in Setup/Connections c:: Connection checklist 5.4 The Another access point with the same SSID exists is displayed during setup 5.5 The New port could not be created is displayed during setup 5.6 The Set Printer IP Address dialog box is displayed during setup 5.7 The Enter Password dialog box is displayed during setup 5.8 The You have connected the printer to an unsecured wireless network is displayed during setup 5.9 The Communication with the Card Slot failed is displayed during setup 5.10 The The Card Slot is already mapped as Network Drive to this computer is displayed during setup 5.11 The Cannot map any more drives, because all the drive le«ers are assigned is displayed during setup 5.12 The Timeout error screen is displayed during WPS setup P.4 P.4 P.4 P.5 P.5 P.5 P.6 P.6 P.6 2 Cannot connect to the access point (the access point is not detected) 2.1 The target access point is not detected 2.2 Cannot connect to the target access point 2.3 Using the machine in a multiple access point setup 3 How to set a network key/network password 3.1 About Network Key (Windows)/Network Password (Macintosh) 3.2 How to set a WEPIWPAlWPA2 key 4 Cannot connect to the machine (the machine is not detected) P.1 P.1 P.1 P.1 P.2 P.2 P.2 P.2 · ':6 " Re.etting the machine 7 The admin password set to the machine was forgotten · r:8 , Changing the port name lVI1ljmm • • Restoring the Machine to the Factory Settings 1 Initializing using the machine's Operation Panel P.6 P.7 4.1 The machine is not detected P.2 4.2 No machine is detected after the network settings are changed in Windows l'f'l~ P.2 5 The following screen is displayed during setup 5.1 The Access Points dialog box is displayed during setup 5.2 The An access point could not be detected is displayed during setup 5.3 The Printer could not be connected to the specified access point is displayed during setup • Specifications P.3 · ~ p.~ MP980 series P.3 P.3 ·0 MP620 series p.~ P.4

• Confirm the network name/SSID of the target access point and set the machine to use the identi- cal network name/SSID. If the network name/SSID is different in the machine and the access point, the machine cannot connect to the access point. For details, refer to "5.1 The Access Points dialog box is displayed during setup' on page 3. " The wireless channel to be used may be limited depending on wireless network devices installed in the computer. Confirm the wireless channels available for the network device. For details, refer to the manual provided with your computer or your wireless network device. Make sure that the channel set to the access point is valid to communicate with the computer, confirmed above. If not, change the channel set to the access point. • If MAC address filtering is enabled, we recommend that you register the machine's MAC address to the access point before entering setup. To confirm the MAC address of the machine, refer to "About Network Communication' - "Troubleshooting" in the on-screen manual: Advanced Guide. • If the access point's IP address filtering is enabled, disable it during setup. After setup is com- plete, turn the IP filtering feature back on. , If Client-ta-Client Blocking is enabled, an access point may be capable of blocking all direct transmission among clients associated to it. If such feature is enabled, disable this feature while using the machine. " This machine does not support WPAlWPA2-Enterprise. When you select an access point set to use WPAlWPA2-Enterprise, it is grayed out and cannot be set up. W----- 1{0 Z Z'Z "'Z~»»'- ,.,.. " , TrO'lbles in $etup/Co,nnections ~ Connection checklist Before you proceed to Troubleshooting, confirm the following: o The USB cable is securely connected to the correct port. o The machine is turned on and the network device is on. If it is, turn it off and then turn it on again. o If the firewall function of your security software is turned on, a message may appear warning that Canon software is attempting to access the network. If the warning message appears, set the secu- rity software to always allow access. o When using a router, connect the machine and computer to the LAN side (same network segment). o The machine's LAN setting is configured according to your connection method. To connect over wireless LAN, set Change wirelessJwired to Wireless LAN active. To connect over wired LAN, set it to Wired LAN active. For the procedure, refer to "Machine's LAN Setting" in the printed manual: Getting Started. If you have changed the machine's LAN setting, set up the machine again following the procedures in "Install the Software" and onward in the printed manual: Getting Started. Confirm the following before setting up on a wireless LAN: o There is no barrier or obstacle between the access point and the machine. o The access point is operating in IEEE802.11b or IEEE802.11g (2.4 GHz). 2 Cannot connect to the access point (the access point is not detected) 2.1: , Refer to"1 Connection checklist" on page 1 and make sure there is no problem. , If the machine or your computer cannot communicate with the target access point, follow the procedure below. o Ensure that the access point is on and then click Update in the Access Points dialog box. o If the access point is still not detected, move your machine closer to the access point and remove possible Obstructions, then click Update. €) Ensure that your computer can communicate with the access point. o Unplug the access point from the power outlet and plug it in, then click Update. • Using your access point's utility software, check if your access point is set to the stealth mode, I.e., set not to broadcast its SSID, or is set to reject clients whose SSID is set to ANY. If so, click Manual Setup and enter the access point's SSID in SSID. For details, refer to "5.1 The Access Points dialog box is displayed during setup" on page 3. , Make sure that the machine and the access point can communicate with each other under this setting. When encryption is set to the access point, set up the encryption of the machine to match the settings of the access point. If the WEPIWPAlWPA2 (encryption key) is different in the machine and the access point, the machine cannot communicate with the access point. For details, refer to '3.2 How to set a WEPIWPAlWPA2 key" on page 2. Confirm the following the access point to be used can communicate with the machine and the computer. Windows XP may automatically connect to an unintended access point. Follow the steps below to make your access point the highest priority. o Select Start and Connect To. o Right dick Wireless Network Connection and select Properties. €) Click Wireless Networks tab and confirm that Use Windows to configure my wireless net· work settings is checked. o Confirm that the target access point is displayed in the Preferred networks list. If the access point is not set to the top in the list, select and move the access point to the top of the list using the Move up. If multiple networks are available when using Macintosh, select System Preferences, select Network, select AirPort and click Advanced (Mac OS X v.1 0.4.xlv. 10.3.9: select Network Port Configuration), then change the priority of the network name that you want to use. If the network name is not set to the highest priority, select and move it to the top of the list (the highest priority).

• When using WPNWPA2 The authentication method, passphrase, and dynamic encryption type must match on the access point, the machine, and the computer. Enter the passphrase configured on the access point (a sequence of between 8 and 63 alphanu- meric characters, or a 64-character hexadecimal number). If you do not know the passphrase, refer to the manual provided with the access point, or consult its manufacturer. Select either TKIP (8asic Encryption) or AES (Secure Encryption) for the dynamic encryption method. An encryption key used in wireless networks. As using passwords, settings must match among the access point, the machine, and the computer. A WEP key is used in the WEP authentication method, while Passphrase or Pre-Shared Key is used in the WPNWPA2 authentication method. ~ • Names of network keys vary depending on your access point or application software. ~ ~ • This machine supports WPA-PSK (WPA-PersonaJ) or WPA2-PSK (wpA2-PersonaJ). WPN WPA2-Enterprise is not supported. • When using WEP The key length, key format, the key to use (out of 1 to 4), and the authentication method must match among the access point, the machine, and the computer. For access points that use automatically generated WEP keys, use the hexadecimal key format for the machine. If you do not know the access point WEP key, refer to documentation provided with the access point or contact its manufacturer. Example: Using 64 bit key length, when the string 'canon' is entered, an access point generates the fol- lowing codes. - Key 1: C9 42 28 88 AE - Key 2: 87 CO FB 05 68 - Key 3: 9A 15 F8 F6 F3 - Key 4: 62 56 67 58 44 In order to communicate with such an access point, you must configure the machine to use the key generated by the access point by entering it in hexadecimal format. Normally, select Auto for the Authentication. Otherwise, select Open System or Shared Key ac- cording to the setting of the access point. When entering a WEP key in Network Key or Network Password on the Access Points screen, the key number is set to 1 and the Authentication is set to Auto. The key length and format are based upon value of the entered key. Cannot connect to the machine (the machine is not detected) 2 ~ ~ • When using AirPort, confirm the settings in Wireless Security of AirPort Admin Utility. - Select 64 bit if 40 bit WEP is selected for the Key Length in the AirPort Base Station. - Select 1 for Key 10. Otherwise the computer will not be able to communicate with the machine via the access point. • Refer to '1 Connection checklist' on page 1 and make sure there is no problem. • If the access point is configured to use access contrOl, register the IP address or the MAC ad- dress of the machine or disable the access control. • Confirm the network name/SSID of the target access point and set the machine to use the identi- cal network name/SSID. If the network name/SSID is different in the machine and the access point, the machine cannot connect to the access point. For details, refer to '5.1 The Access Points dialog box is displayed during setup' on page 3. • Make sure that the machine and the access point can communicate with each other under this setting. When encryption is set to the access point, set up the encryption of the machine to match the settings of the access point. If the WEPIWPNWPA2 (encryption key) is different in the machine and the access point, the machine cannot communicate with the access point. For details, refer to '3.2 How to set a INEPIWPANVPA2 key' on page 2. • The wireless channel to be used may be limited depending on wireless network devices installed in the computer. Confirm the wireless channels available for the network device. For details, refer to the manual provided with your computer or your wireless network device. Make sure that the channel set to the access point is valid to communicate with the computer, confirmed above. If not, change the channel set to the access point. Wait until the IP address is assigned to the computer. You may need to restart your computer. Search for the machine again after confirming a valid IP address is assigned to the computer.

(WPNWPA2) selected in Encryption Method can be confirmed and changed. (0) Connect Connects to the specified access point. The following screen is displayed during setup The Access Points dialog box is displayed when: - No access point is detected. - Multiple access points are detected. Select the target access point, then perform necessary operation such as setting of encryption. If you want to specify access point manually, click Manual Setup in the Access Points dialog box. Enter the settings for the target access point in the Manual Setup dialog box, then click Connect. The target access point is searched with the specified settings. For changing settings of the access point, refer to the manual provided with the access point or contact its manufacturer. T~ U ... " If you connect to a network that is not protected with security measures, there is a risk of disclosing data such as your personal information to a third party. " If a password (WEP key)/passphrase (WPNWPA2 key) has not been set, a detailed set- tings dialog box is displayed. To change the settings, dick the Configuration in the Manual Setup dialog box. For details, refer to "3.1 About Network Key (VVindows)/Network Pass- word (Macintosh)" on page 2. (A) Network (SSIO) Enter the Network (5SI0) set to the access point. The Network (5510) is case sensitive. When using AirPort, enter the Network (S510) in alphanumeric characters. SSIO is also called E55-10. For details, refer to the manual provided with your access point or contact its manufacturer. (8) Encryption Method " Do not use Select to disable encryption • Use WEP Transmission is encrypted using the password (WEP key) you specified. " UseWPA Transmission is encrypted using the passphrase (WPNWPA2 key) you specified. The actual encryption key is renewed automatically at a certain time interval, making the trans- mission harder to break. (C) Configuration The detailed settings dialog box is displayed. The password (WEP key) or the passphrase (WPN WPA2 key) selected in Encryption Method can be confirmed and changed. (0) Connect Connects to the specified access point. This message is displayed when no access point is detected. Clicking the OK displays the Access Points dialog box. For details, refer to "2.1 The target access point is not detected" on page 1. aa ~ ·:""-(A) -(C) " If a WEP key/Passphrase (WPNWPA2 key) has not been set, a detailed settings dialog box is displayed. To change the settings, dick the Configuration in the Manual Setup dialog box. For details, refer to "3.1 About Network Key (VVindows)/Network Password (Macintosh)" on page 2. (A) SSIO Enter the S510 set to the access point. The 5510 is case sensitive. When using AirPort, enter the network name (5SI0) in alphanumeric characters. 5510 is also called E55-10. For details, refer to the manual provided with your access point or contact its manufacturer. (8) Encryption Method " Do not use 5elect to disable encryption. • UseWEP Transmission is encrypted using the WEP key you specified. " UseWPA Transmission is encrypted using the passphrase (WPNWPA2 key) you specified. The actual encryption key is renewed automatically at a certain time interval, making the trans- mission harder to break. ~ -----

o Open the System Properties screen. , Windows Vista Click Start, right-dick Computer, select Properties, then dick Change settings in the Computer name, domain, and workgroup settings column. User Account Control screen appears, dick Continue. , Windows XP/2000 Right-dick My Computer, then select Properties. 6 Select the Computer Name tab, then click Change. o Change the workgroup name to "WORKGROUP', then dick OK. To open port 137:139: o Open the screen for setting Windows Firewall. , Windows Vista Click Start> Control Panel> Allow a program through Windows Firewall. User Ac- count Control screen appears, dick Continue. , Windows XP/2000 Click Start> Control Panel> Security Center> Windows Firewall. 6 Select the Exceptions tab, and dick Add port. o On the Add a Port dialog box, input the following information, and click OK. - Name: Input any name for the port. - Port number: Input "137". - TCP/UDP: Select TCP. () Repeat steps 6 and O. On the Add a Port dialog box, input the same information as you did in step 0 except for selecting UDP in TCP/UDP. o Use the same procedure to open the other ports (138TCP, 138UDP, 139TCP, and 139UDP). (} Confirm that the port names are added on the Exceptions sheet, and dick OK. " If the problem is not resolved, click Skip to complete the installation without the network setup of the Card Slot After installation is complete, to mount the Card Slot uSing the Canon IJ Network Tool, refer to "Using the Card Slot over a Network" in "About Network Com- munication' in "Appendix' of the on-screen manual: Advanced Guide. To mount the Card Slot manually, refer to "Cannot Mount the Card Slor in "About Network Communication" in "Troubleshooting" of the on-screen manual: Advanced Guide. sa ~ , If you connect to a network that is not protected with security measures, there is a risk of disclosing data such as your personal information to a third party. This message is displayed when installation of the network drive of the Card Slot fails during setup. Wait for a while, then dick Retry. The Enter Password dialog box is displayed if an administrator password is set to the machine which has already been set up. Admin Password Enter the administrator password you have set The administrator password consists of alphanumeric characters and is no longer than 32 characters. The password is case sensitive. For security, your entry will be displayed by"·" (asterisks) for Windows and "." (bullets) for Macintosh. Security is not configured on the access point. The machine can still be used, so continue the setup procedure to complete it. (A) Retry Click to retry the network setup of the Card Slot. (B) Skip Click to continue installation without the network setup of the Card Slot. If it fails again after dicking Retry, follow the procedure below. , Make sure that the computer is communicating with the network properly, then try again. , Disable the Windows Firewall function, or open port 137:139 to allow communication with the machine following the procedure below. For information on other security software, refer to its instruction manual or contact its manufacturer. , If you disabled the firewall function, disconnect your network from the Intemet To do this, configure your router not to connect to the Intemet or WAN. , Make sure that a memory card is inserted in the Card Slot. If it is not inserted, insert it. To disable the Windows Firewall: o Open the screen for setting Windows Firewall. , Windows Vista Click Start> Control Panel> Allow a program through Windows Firewall. User Ac- count Control screen appears, dick Continue. , Windows XP/2000 Click Start> Control Panel> Security Center> Windows Firewall. 6 Select the General tab, check Off, then click OK. ~ ~ , Depending on the Mac OS version, the authentication screen may appear. If it appears, click OK. • If the problem is not resolved, click Skip to complete the setup without the network setup of the Card Slot To mount the Card Slot manually, refer to "Cannot Mount the Card Sior in "About Network Communication" in "Troubleshooting" of the on-screen manual: Advanced Guide.

" Restore the machine to the factory default and set up the machine again. For details, refer to "Restoring the Machine to the Factory Settings" on page 7. To set up the machine again, follow the procedures in "Install the Software" and onward in the printed manual: Getting Starled. " If you have changed the connection method via Change wirelesslwired in the machine's LAN setting, you need to setup the machine again. To do so, follow the procedures in "Install the Software" and onward in the printed manual: Getting Starled. ) ) Re-setting the machine Restore the machine setting to factory default. All settings previously set will be lost after initialization. Set up the machine again to use it. For details, refer to "6.1 Re-setting the machine" on page 6. To change the port name, click View Setup Results in the Setup Completion dialog box, then click Set Port Name. The Set Port Name dialog box is displayed, where you specify the port name. By changing the port name, you can change the name of the machine. When you set up an additional computer to use the machine whose port name you changed, the machine is displayed with the changed port name. When two or more computers are set up, the changed name is displayed. When multiple computers or machines are present, this can be used to change the name to one that is easy to remember. "GChanging the port name iVflmnm This screen is displayed when WPS setup is not completed within the specified time (2 minutes for the push button method, and 10 minutes for the PIN code method). Retry following the procedures below. " When using the push button method o Press the OK button. The WPS setting screen returns. {} Select Push button method and press the OK button. €) Press the OK button. o When the access point is ready, press the OK button on the machine, then press the WPS button on the access point within two minutes. " When using the PIN code method o Press the OK button. The WPS setting screen returns. {} Select PIN method and press the OK button. A new PIN code appears. €) Set the new PIN code to the access point or computer. Port Name Port names should consist of alphanumeric characters and be no longer than 21 characters, excluding the prefix. The port name includes the fixed prefix 'CNBJNP_", which you do not need to enter. 6

, RtltorjlJS the Machine to the Factory Settings o Select Yes and press the OK button. Do you want to restore LAN setting. to the factory settings? 1 Initializing using the machine's Operation Panel Ve. No Follow these steps to restore the machine's network settings to factory defaults, o Open the Operation Panel on the machine, use the Easy-Scroll Wheel or the -4 or • button to select Settings, then press the OK button. iRemaining ink voill Introduction (j) Confirm that the right screen appears. After a while, the LAN settings screen returns. • The machine's network settings are restored to factory defaults. Following i. completed. Reset LAN SIttings e Select Device settings and press the OK button. €) Select LAN settings and press the OK button, o Select Reset LAN settings and press the OK button. " Setting. '. I~I .,JJJ Device setting. 2/3 Perform various .etting•. \/- Device settings Plain paper feed setting. Print .etting. LAN settings AdVance,f.ettings---- Mobile phone print .etting PictBridga print .etting. --- Limguige sil8ctiOoi - - _. - . --_.--,.----- .,'~ LAN .ettings Change wireless/wired Wireless LAN settings Wirele.s LAN setting list Wired LAN .etting ~st IPv4/IPv6 setting' WSD setting Reset LAN settings • Factory Default Active BJNPSETUP Disable IPaddress: 192.168.1.123 (default) • Subnet mask: 255.255.255.0 • Default gateway: 0.0.0.0 Inactive • IPaddress: 192.168.1.123 (default) • Subnet mask: 255.255.255.0 • Default ateway: 0.0.0.0

'~~ ,la8QifiQiltiaJlI ~~,:, MP980 series ) ~ Conform to the operating system's requirements when higher than those given here. Minimum System Requirements Mac OS X v.l0A Intel processor, PowerPC G5, PowerPC G4, PowerPC G3 256MB Mac OS X v.l0.5 Intel processor, PowerPC G5, PowerPC G4 (867 MHz or faster) 512MB Mac as X v.l0.3.9 PowerPC G5, PowerPC G4, PowerPC G3 128MB Safari Note: Hard Disk must be formatted as Mac as Extended (Joumaled) or Mac as Extended. 750MB Note: For bundled software installation. \/\Iindows 2000 Professional SP4 300 MHz processor 128MB \/\Iindows XP SP2 300 MHz processor 128MB Note: Operation can only be guaranteed on a PC with \/\Iindows Vista, XP or 2000 pre-instaled. Operating System \/\Iindows Vista Processor 1 GHz processor RAM 512MB CD-ROM Drive Required Browser Internet Explorer 6.0 or later Display XGA 1024 x 768 Hard Disk Space 650 MB Note: For bundled software installation. o Some functions may not be ava~able ~h \/\Iindows Media Center. o To upgrade from \/\Iindows XP to \/\Iindows Vista, first uninstall software bundled with the Canon inkjet printer, Additional System ReqUirements for the on-screen manuals Browser: Easy Guide Viewer Browser: Help Viewer Note: Microsofllntemet Explorer 6.0 or later Note: The on-screen manual may not be must be instaled. The on-scresn manual may displayed property depending on your not be displayed property depending on your operating system. we recommend that you operating system or Intemet Explorer version. keep your system up 10 dale. we recommend that you keep your system up to date with \/\Iindows Update. Specifications are subject to change without notice. About Consumables Consumables (ink tanks I FINE Cartridges) are available for 5 years after production has stopped. 25%0400% (1 % unit) Gray: 48 bit/8 bit (Film Scan: 48 bit!16 bit or 8 bit) Color: 48 bit!24 bn (RGB each 16 bit/8 bit) (Fam Scan: 48 bit!48 b~ or 24 bit) Network Specifications TCPIIP Optional resolution (horizontal vertical) max: 4800 dpi x 9600 dpi Interpolated resolution max: 19200 dpi x 19200 dpi Copy Specifications A4/Letter, 8.5" x 11.7"/216 x 297 mm 9 positions, Auto intensity (AE copy) Max 99 pages TWAlNM4A (\I\Iindows Vista and \/\Iindows XP only) Scan Specifications Supported Standards: IEEE802.11g11EEE802.11b Transfer speed: IEEE802.11g: 619/12/18/24/36148154 Mbps IEEE802.11b: 1/2/5.5111 Mbps Frequency bandwidth '1: 2.412 GHz-2.462 GHz or 2.412 GHz-2A72 GHz Channel'l: 1-11 or 1-13 Communication distance:Indoors 50 m '2 Security: Encryption by WPA-PSK, WPA2-PSK, or WEP (64/128 bits), and access control by passwords '1 Frequency bandwidth and avaUable channels differ depending on country or region. '2 Effective range varies depending on the inslalation environment and location. Supported Standards: IEEE802.3u (lOOBASE-TX)/ IEEE802.3 (10BASE-T) Transfer speed: 1OWl ooMbps (auto switching) Multiple copy Scanner driver Reduction/ Enlargement Intensity adjustment Scanning resolution Gradation (Input! Output) Maximum scanning size \/\Iireless LAN Communication protocol \/\Iired LAN General Specifications Printing resolution 9600 (horizontal)' x 2400 (vertical) (dpi) , Ink droplets can be placed with a pitch of 119600 inch at minimum. Interface USB Port: Hi-Speed USB '1 Direct Print Port: PictBridge IrDAIR '2 Bluetooth v2.0 (Option) *3 '4 '5 USB flash drive LAN Port: Wred LAN: 100BASE-TXl10BASE-T \/\Iireless LAN: IEEE802.11bnEEE802.11g'6 '1 A computer that complies with Hi-Speed USB standard is required. Since the Hi-Speed USB interface is fully upwardly compatible with USB 1.1, it can be used at USB 1.1. '2 Maximum speed: 115.2 Kbps Operating range: within 30 em *3 Maximum speed: 1.44 Mbps '4 JPEGIPNG only '5 Bluetooth connection is for printing only. '6 Setup possible through WPS (\I\Ii-Fi Protected Setup) and WCN (\I\Iindows Connect Now). Print width 8 inches 1203.2 mm (for Bordefless Printing: 8.5 inches/216 mm) Acoustic noise Approx. 44.5 db(A) level ' Wlen printing in the standard print qUality mode on Photo Paper Plus Glossy II) Operating Temperature: 5 to 35'C (41 to 95'F) environment Humidity: 10 to 90% RH (no condensation) Storage Temperature: 0 to 40'C (32 to l04'F) environment Humidity: 5 to 95% RH (no condensation) Power supply AC l00-240V, 50/60 Hz Power Printing (Copy): Approx. 27 W consumption Standby (minimum): Approx. 2.7 W' OFF: Approx. 0.8 W' , USB connection to PC Eternal Approx. 18.5 (W) x 15.2 (D) x 7.9 (H) inches dimensions Approx. 470 (W) x 385 (D) x 199 (H) mm o \/\lith the Paper Support and Paper Output Tray retracted. weight Approx. 10.7 kg (Approx. 23.6Ib) , \/\lith the Print Head and ink tanks instaled. Print Headnnk Total 6,144 nozzles (PgBK 512 nozzles, Y/DyeBK each 512 nozzles, CIM/Gy each 1536 nozzles) 8

(dpi) "Ink droplets can be placed with a pitch of 119600 inch at minimum. M/Letter, 8.S" x 11.7"/216 x 297 mm 2S%-400% (1 % unit) Minimum System Requirements ~ Conform to the operating system's requirements when higher than those given here. fflm:rl M;4;rir..~'ri Operating System VoAndows Vista Mac OS X v.10.S Processor 1 GHz processor Intel processor, PowerPC GS, RAM S12 MB PowerPCG4 (867 MHz or laster) S12MB Wndows XP SP2 Mac OS X v.l0,4 300 MHz processor Intel processor, PowerPC GS, 128MB PowerPC G4, PowerPC G3 256MB Wndows 2000 Professional SP4 Mac OS X v.10.3.9 300 MHz processor PowerPC GS, PowerPC G4, 128MB PowerPC G3 128MB Note: Operation can only be Note: Hard Disk must be formatted guaranteed on a PC with as Mac OS Extended Wndows Vista, XP or 2000 (Joumaled) or Mac OS pr&-instaled. Extended. Browser Intemet Explorer 6.0 or later Safari Hard Disk Space 650MB 7S0MB Note: For bundled soltware Note: For bundled soltware installation. installation. CD-ROM Drive Required Display XGA 1024 x 768 ° Some functions may not be ava~able with VoAndows Media Center. ° To upgrade from Wndows XP to VoAndows Vista, first uninstal soltware bundled with the Canon inkjet printer. IEEE802.11gnEEE802.11b 6/9/12/18/24/36/48154 Mbps 1/2/S.S/11 Mbps 2,412 GHz-2,462 GHz or 2.412 GHz-2.472 GHz 1-11 or 1-13 Indoors 50 m °2 Encryption by IM"A-PSK, 1M"A2-PSK, or WEP (64/128 bits), and access control by passwords Gray: 16 bi1/8 bit Color: 48 bill24 bit (RGB each 16 bi1/8 bit) Optional resolution (horizontal vertical) max: 2400 dpi x4800 dpi Interpolated resolution max: 19200 dpi x 19200 dpi Copy Specifications TWAlNIIMA (Wndows Vista and Wndows XP only) Tcpnp Network Specifications Scan Specifications 9 positions, Auto intensity (AE copy) Max 99 pages Channel "1: Communication distance: Security: Supported Standards: Transfer speed: IEEE802.11g: IEEE802.11b: Frequency bandwidth "1: Intensity adjustment Multiple copy Maximum scanning size Reduction! Enlargement Scanner driver Scanning resolution Gradation (Inpull Output) Wn!lessLAN Communication protocol Temperature: S to 3SoC (41 to 9S°F) Humidity: 10 to 90% RH (no condensation) AC 1QO.240V, SO/50 Hz °1 A computer that complies with Hi-Speed USB standard is required. Since the Hi-Speed USB interface is fully upwardly compatible with USB 1.1, it can be used at USB 1.1. "2 Maximum speed: 1,44 Mbps °3 JPEGIPNG only "4 B1uetooth connection is for printing only. "S Setup possible through IM"S (V\\-Fi Protected Setup) and VllCN (Wndows Connect Now). Temperature: 0 to 40°C (32 to 104°F) Humidity: Sto 9S% RH (no condensation) Direct Print Port: PictBridge B1uetooth v2.0 (Option) "2 "3 °4 USB flash drive LAN Port: VoAred LAN: 100BASE-TX/10BASE-T VoAreless LAN: IEEE802.11b11EEE802.11g oS 8 inches /203.2 mm (for Bord9fless Printing: 8.S inchesl216 mm) Approx. 43.S db(A) ° Wlen printing in the standard print quality mode on Photo Paper Plus Glossy II) USB Port: Hi-Speed USB °1 Interface Acoustic noise level Print width Storage environment Operating environment Power supply Power consumption Etemal dimensions Vlleight Print Headnnk Printing (Copy): Approx. 17 W Standby (minimum): Approx. 3.2 W ° OFF: Approx. 0.7 W" " USB connection to PC Approx. 17.8 CNI x 14.S (D) x 6.9 (H) inches Approx. 4S0 CNI x 368 (D) x 176 (H) mm • VoAth the Paper Support and Paper Output Tray retracted. Approx. 8.6 kg (Approx. 19.0 Ib) • VoAth the Print Head and ink tanks installed. Total 2,368 nozzles (PgBK 320 nozzles, Y/DyeBK each 258 nozzles, CIM each 768 nozzles) WredLAN '1 Frequency bandwidth and available channels differ depending on country or region. '2 Effective range varies depending on the instalation environment and location. Supported Standards: IEEE802.3u (1 ooBASE-TX)I IEEE802.3 (10BASE-T) Transfer speed: 1OMl1ooMbps (auto switching) Additional System ReqUirements for the on-screen manuals Browser: Easy Guide Viewer Browser: Help Viewer Note: Microsoft Internet Explorer 6.0 or later Note: The on-screen manual may not be must be instaled. The on-screen manual may displayed properly depending on your not be displayed properly depending on your operating system. We recommend that you operating system or Intemet Explorer version. keep your system up to date• We recommend that you keep your system up to date with Wndows Update. Specifications are subject to change without notice. About Consumables Consumables (ink tanks I FINE Cartridges) are available for 5 years after production has stopped.

PRINTED IN THAILAN IMPRIME EN THAILAND

k ~ .1. roper an m90 e rmt ea an n Ian s ~ ~ Print Head Ink Tanks Handle the Print Head and ink tanks of this product properly, observing the cautions noted below. Improper handling causes malfunction or other problems in the product, as well as damaging the Print Head or ink tanks. Note: The below illustrations may be different from your product. 1) When you install the Print Head in the product, insert the Print Head into the Print Head Holder carefully not to knock it against the sides of the holder. Also be sure to install it in a well-lit environment. (For details, refer to Getting Started.) ~~~;¢::r:::'ir:7:t- Print Head Holder 2) Do not attempt to disassemble or modify the Print Head and ink tanks. 3) Do not handle the Print Head and ink tanks roughly such as applying them excessive pressure or dropping them. 4) Do not rinse or wipe the Print Head and ink tanks. 5) Once you have installed the Print Head and ink tanks, do not remove them unnecessarily. FRAN<;AIS Remarque importante AAvertissement ~ ~ Manipulation de la Tete d'impression et des Reservoirs d'Encre ~ ~ Tete Reservoirs d'impression d'Encre Manipulez correctement la Tete d'impression et les reservoirs d'encre de ce produit en respectant les avertissements ci-dessous. Une mauvaise manipulation peut notamment perturber Ie fonclionnement du produit et endommager la Tete d'impression ou les reservoirs d'encre. Remarque: Les illustrations ci-dessous peuvent differer de votre apparei!. 1) Lorsque vous installez la Tete d'impression, inserez-Ia dans son support avec precaution pour ne pas la heurter contre les bords du support. Assurez-vous egalement de les installer dans un environnement bien eclaire. (Pour en savoir plus, voir Demarrage.) 1i\i\f.p.,.':::"'..+4+-..,....4-- Support de la Tele d'impression 2) N'essayez pas de demonter ou d'apporter des modifications 11 la Tete d'impression ou aux reservoirs d'encre 3) Ne manipulez pas la Tete d'impression et les reservoirs d'encre avec brutalite (fortes pressions, chutes, etc.). 4) La Tete d'impression et les reservoirs d'encre ne doivent etre ni rinces ni essuyes. 5) Une fois installes, ne retirez pas la Tete d'impression et les reservoirs d'encre sans raison. QT5-1733-V01 062008YT ©CANON INC. 2008 PRINTED IN THAILAND

Cabezal de Depositos Impresion de Tinta Trate correctamente el Cabezal de Impresi6n y los dep6sitos de tinta de este producto, teniendo en cuenta los avisos que aparecen a continuaci6n. Un manejo inapropiado provoca un funcionamiento incorrecto u olros problemas en el produclo, asi como danos en el Cabezal de Impresi6n 0 los dep6sitos de tinta. Nota: Pueden existir diferencias entre las siguienles iluslraciones y su producto. 1) AI instalar el Cabezal de Impresi6n en el producto, inserte con cuidado el Cabezal de Impresi6n en el Soporte del Cabezal de Impresi6n para evitar que se golpee con los lados del soporte. Asimismo. asegurese de instalarlo en un entomo bien iluminado. (Para oblener mas informaci6n, consulte la Guia de inicio.) ~~~~);::l-"tt::::::::1""- Soporte del Cabezal de Impresion 2) No intenle desmontar ni allerar el Cabezal de Impresi6n ni los dep6sitos de tinta. 3) No Irate de forma inadecuada el Cabezal de Impresi6n ni los dep6sitos de tinta. No ejerza demasiada presi6n sobre ellos ni los deje caer. 4) No lave ni limpie el Cabezal de Impresi6n ni los dep6sitos de tinta. 5) Cuando haya instalado el Cabezal de Impresi6n y los dep6sitos de tinta, no los retire si no es necesario. PORT DO BRASIL Aviso importante ACuidado ~ Manuseio Apropriado da Cabe~a de Impressao e dos Cartuchos de Tinta ~ ;, Cabeya de Cartuchos Impressao de Tinta Manuseie corretamente a Cabec;:a de Impressao e os cartuchos de tinta desle produto, observando os cuidados indicados abaixo. 0 manuseio inadequado causa mau funcionamento ou outros problemas com 0 produlo, alem de danificar a Cabec;:a de Impressao ou os cartuchos de tinta. Nota: As ilustrac;:6es abaixo podem diferir do seu produto. 1) Ao instalar a Cabec;:a de Impressao no produto, insira cuidadosamente a Cabec;:a de Impressao no Suporte da Cabec;:a de Impressao para que ela nao bata contra as laterais do suporte. Certifique-se tambem de instala-Ia em um ambiente bem iluminado (Para obter detalhes, consulte Para Come9ar.) ~~~~)::::rtt:::::::1""- Suporte da Cabe<;a de Impressao 2) Nao tente desmontar ou modificar a Cabec;:a de Impressao e os cartuchos de tinta. 3) Manuseie a Cabec;:a de Impressao e os cartuchos de tinta delicadamente, sem aplicar pressao excessiva, nem deixa-Ios cair. 4) Nao lave nem esfregue a Cabec;:a de Impressao e os cartuchos de tinta. 5) Ap6s instalar a Cabec;:a de Impressao e os cartuchos de tinla, nao os remova desnecessariamente.

A: Load photo paper in the Rear Tray. B: Load plain paper in the Cassette. The illustration may be different from your product. Wlc~htiger Hinweis DEu;1;~CH Stellen Sie sicher, dass Sie den jeweiligen Medientyp in die richtige Papierquelle einlegen. A: Legen Sie Fotopapier in den hinteren Papiereinzug ein. B: Legen Sie Normalpapier in die Papierkassette ein. Die Abbildung kann von Ihrem Produkt abweichen. Remarque importante FRANCAIS Assurez-vous que I'alimentation papier correspond au type de support charge. A : chargez du papier Photo dans Ie receptacle arriere. B : chargez du papier ordinaire dans la cassette. II peut y avoir des differences entre I'illustration et Ie produit. Belangrijke mededeling NEDERLANDS Zorg ervoor dat u papier in de juiste papierbron plaatst. A: plaats fotopapier in de papiertoevoer aan de achterzijde. B: plaats gewoon papier in de cassette. De afbeelding kan afwijken van uw apparaat. Aviso importante . . ESPANOL Asegurese de utilizar la fuente de papel correcta para el tipo de soporte que se va a cargar. A: Cargue papel fotogrwTOvpaq>IKo xapri OTI)V niow 8~KI). B: Tono8ET~OTE anM xapTi OTI)V KaoEra. H anEIKOVIOI) EVOEXETOI va ola

spos6b. A: Papier folograficzny nalezy zaladowac do Iylnej lacy. B: Zwykly papier nalezy zaladowac do kasely. Przedslawiona iluslracja moze r6znic si~ od posiadanego modelu produklu. Dolezite upozornenie SLOVENSKY Dbajle na 10, aby sle pre vlozeny Iyp media pouzili spravny zdroj podavania papiera. A: Do zadneho zasobnika vlozle folograficky papier. B: Do kazety vlozte obycajny papier. Obrazok moze by!' odlisny od vasho vyrobku. Ba>KHaJi MHepOpMa~MJI PYCCKIr1III Y6e,QI'lTeCb BI'lCnOnb30BaHI'll'l npaBl'lnbHOrO I'lCT04HI'lKa 6yMarl'l ,QnSl 3arpYlKeHHoro HOCI'lTenSl. A: 3arpylKai1Te cj:>OT06yMary B 3a,QHI'li1 nOTOK. B: 06bl4HYlO 6yMary cne,QyeT 3arpYlKaTb BKacceTy. v1306palKeHl'le MOlKeT OTnl'l4aTbCSl OT npl'l06peTeHHoro l'l3,QenI'lSl. Oluline teave EESTI Kasutage laadimiseks kindlasli 5igel tOOpi paberit A: laadige fotopaber lagasalve. B: laadige lavapaber kassettL Joonis v5ib teie lootesl erineda. SvadQs pazi90jums LATVIESU Parliecinielies, ka ievielojal malerialu pareizaja papTra uztvereja. A: levielojiel fotopapTru aizmugures uZlvereja. B: levielojiel kasete paraslo papTru. Izslradajums var izskatHies ciladi neka redzams ilustracija. Svarbi pastaba .; L1ETUVISKAI [silikinkile, kad lkeltai daugialypei lerpei naudojale linkamq popieriaus saltinl. A: NuolraukL[ popieriL[ dekile l galin[ deklq. B: Nespalvotq popieriL[ dekile l kasel~. lIiuslracija gali skirtis nuo jOSL[ gaminio. Pomembno obvestilo SLOVENSCINA Uporabile ustrezen vir papirja za vrslo medija, ki jo zelite nalozitL A: Folografski papir nalozite v zadnji pladenj. B: Navaden papir nalozite v kaselo. Slika se lahko razlikuje od vasega izdelka. Onemli t.lyan TORKc;E YOklenmekle olan ortam tOrO iyin dogru kaglt kaynaglnl kullandlglnlzdan emin olun. A: Fotograf kagldlnl Arka Tepsi'ye yOkleyin. B: DOz kagldl Kasel'e yOkleyin. Resim OrOnOnOzden farkh olabilir. Ba>Kl1MBa iH4»opMa~iJl YKPAi"HCbKA 060B'Sl3KOBO BI'lKOpl'lcToByi1Te npaBl'lnbHe ,QlKepeno nanepy ,QnSl 3aBaHTalKysaHoro Tl'lny HOciSl. A: 3asaHTalKyi1Te cj:>oTOnanip,Qo 3a,QHboro nOTKa. B: 3asaHTalKyi1Te 3SI'l4ai1HI'li1 nanip ,QO KaCeTI'l. InlOCTpaL1iSl MOlKe si,Qpi3HSlTI'lCSl si,Q sawarD npo,QyKTy. Ba>KHa aa6ene>KKa SbnrAPCKIr1 BHI'lMasai1Te ,Qa 1'l3nOmSaTe npaSl'lnHI'lSl 1'l3T04HI'lK Ha XapTI'lSl 3a 3ape,QeHI'lSl Tl'ln HOCI'lTen. A: 3ape,QeTe cj:>oTOxapTI'lSl S3a,QHaTa Tasa. B: 3ape,QeTe 061'lKHOSeHa XapTI'lSl SKaceTaTa. BaWI'lSlT npo,QyKT MOlKe ,Qa ce pa3nl'l4aSa OT nOKa3aHOTO Ha cj:>l'lrypaTa. Anu!ltimportant ROMANA Asigura\i-va ca uliliza\i sursa corecla de hartie pentru lipul de suport de imp'rimare care esle incarcat A: !ncarca\i hartie fotografica in lava poslerioara. B: Incarca\i hartie obi:?nuila in caseta. Imaginea poate avea un aspecI diferil de cel al produsului dvs. .~ .....,,,.iJ1 ,b;L...~1 t~ ~I ,;,~I;""""fl"""""'" "",,.. ~I (;:;.>.11 ~ ....I"..:.~,..",I;~I,;" J.4 ,;,~I""I.> ~ ",WI ~;~I J.4> .~"",."..,....,..,~I,......,,.JI .~ cu~1 "",-?I Q~.rS :1)19 4.S sl4.iLw) t~ ~ ~ ~l.o..o 9~ .i.ds ~)I ~-.... .~J;I,,.i~~)JI)~~Ls .~J l,.i ..i.i.Ls ~Ls ):1 I; OJl...aJ.. .,j"LlS ·....;,4 ""I..i.i.. ~ J,...,..,... L """,,I ~ ",,...,

Safety Precautions A Warning • Never attempt to plug the power cord into the power outlet or unplug the power cord when your hands are wet. • Never damage, modify, stretch, or excessively bend or twist the power cord. Do not place heavy objects on the power cord. • • Never use any power supply other than the standard power supply available in the country of purchase. Using the incorrect voltage and frequency could cause a fire or electric shock. • Always push the plug all the way into the power outlet. A Caution • For safety reasons, keep ink tanks out of the reach of children. • In case ink gets in contact with eyes, rinse with water immediately. • In case ink gets in contact with skin, wash with soap and water immediately. • Do not drop or shake ink tanks as this may cause the ink to leak out and stain your clothes and hands. Also read the Safety Precautions in the Basic Guide on-screen manual. Observe the warnings and cautions to avoid personal injury or damage to the machine. International ENERGY STAR@ Program As an ENERGY STAR@ Partner, Canon Inc. has determined that this product meets the ENERGY STAR guidelines for efficiency. Users in the U.S.A. -Regulatory Information FCC Notice (U.S.A. Only) For 120V, 60Hz model Model Number: K10325 (Contains FCC 10: AZDK30306) This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radiolTV technician for help. Use of a shielded cable is required to comply with Class B limits in Subpart B of Part 15 of the FCC Rules. Do not make any changes or modifications to the equipment unless otherwise specified in the manual. If such changes or modifications should be made, you could be required to stop operation of the equipment. FCC ID:AZDK30306 Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. The equipment complies with FCC radiation exposure limits for at uncontrolled equipment.This equipment should be installed and operated with minimum distance at least 20cm between the radiator and persons body (excluding extremities: hands, wrists, feed and legs) and must not be co-located or operated with any other antenna or transmitter. Canon U.S.A., Inc. One Canon Plaza Lake Success, NY 11042 1-516-328-5600 Users in Canada Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. The installer of this radio equipment must ensure that the antenna is located or pointed such that it does not emit RF field in excess of Health Canada limits for the general population; consult Safety Code 6, obtainable from Health Canada's website http://www.hc-sc.gc.ca/. QT5-1689-V01 072008YT © CANON INC. 2008 PRINTED IN THAILAND IMPRIME EN THAILANDE

Precautions de securite A Attention • Ne tentez jamais de brancher ou de debrancher Ie cordon d'alimentation secteur de la prise de courant lorsque vous avez les mains mouillees. • Veillez ane jamais endommager, modifier, etirer, plier ou tordre de fa90n excessive Ie cordon d'alimentation secteur. Ne placez pas d'objets lourds sur Ie cordon d'alimentation. • N'utilisez jamais d'alimentation autre que I'alimentation standard fournie dans Ie pays d'achat. L'utilisation d'une tension et d'une frequence incorrectes risque de causer un incendie ou une . decharge electrique. • Inserez toujours afond la fiche du cable d'alimentation secteur dans la prise murale. A Avertissement • Pour des raisons de securite, veuillez conserver les reservoirs d'encre hors de portee des enfants. • Si de I'encre entre en contact avec les yeux, rincez immediatement aI'eau. • Si de I'encre entre en contact avec la peau, lavez immediatement avec du savon et de I'eau. • Ne faites pas tomber et ne secouez pas les reservoirs: de I'encre pourrait couler et tacher vos vetements et vos mains. Lisez egalement lesprecautions de securite qUifigurent dans Ie manuel en ligne Guide d'utilisation de base. Lisez les avertissements et les misesen garde afind'eviter de vous blesser ou d'endommager la machine. Programme international ENERGY STAR® En tant que partenaire du programme ENERGY STAR®, Canon Inc. a fait en sorte lB. ;.o,,"H que ce produit rl3ponde aux normes du programme ENERGY STAR en matiere de " ." consommation energetique. litlj;Jfiit~'ri Pour les usagers residant au Canada L'usage de I'appareil depend des deux conditions suivantes : (1) cet appareil ne doit pas creer d'interference, et (2) cet appareil doit recevoir toute interference quelle qu'elle soit, y compris une interference pouvant entrainer une operation non desiree de I'appareil. La personne installant cet equipement a ondes radio doit s'assurer que I'antenne est positionnee et orientee de favon a ne pas emettre un champ RF excedant les limites fixees par Sante Canada pour Ie grand public; consultez Ie Code de securite 6 sur Ie site de Sante Canada a I'adresse http://www.hc-sc.gc.ca/.

In business, nothing means more to a company than its reputation. Canon has spent over 70 years building relationships with customers, dealers, and others to become one of the world's most trusted brands. This dedication to excellence continues today through the development of innovative products, first-class customer service, and our total commitment to the Canon experience from discovery to purchase and beyond. That is why we have made it easy to purchase select Canon products and accessories directly from the Canon eStore, where purchasing direct is purchasing smart. Visit us at www.canonestore.com today! High-Performance Papers and Brilliant Inks for Every Project. PROFESSIONAL QUALITY TOP PERFORMANCE EVERYDAY PROJECTS Photo Paper Pro High-gloss photo paper produces truly remarkable photo-lab quality prints which allows you to turn your favorite images into works of art. Digital Art Paper Variety Pack Fine Art paper variety pack includes 5 sheets each of Photo Paper Semi-Gloss, Premium Matte Paper, Photo Rag™Paper, and Museum Etching Paper for your professional prints. Photo Paper Plus Glossy II The perfect rich-finish photo paper you can be proud to frame, display and share. Photo Paper Plus Semi Gloss Velvety photo paper with low glare and soft gloss great for portraits and prints of special moments and memories. Photo Paper Glossy Crisp, glossy paper great for printing snapshots of friends and family. Matte Photo Paper Bright, white matte finish for vibrant colors. Perfect for printing creative projects and portraits. QT1·0728·VOl Printed in Thailand 052008AN QTI0728VOl 1111111111111 Genuine Canon Quality. Whether you need to replace an ink tank or cartridge, only genuine Canon inks will give you the quality you expect from your Canon printer. The Canon ChromaUfel00 system combines PIXMA printers, FINE print head technology and Canon genuine inks with select Canon photo papers to achieve results that rival the quality of conventionally produced photos.

The limited warranty set forth below is given by Canon U.S.A., Inc. ("Canon USA") with respect to the new or refurbished Canon- brand product ("Product") packaged with this limited warranty, when purchased and used in the United States only. The Product is warranted against defects in materials and workmanship under normal use and service (a) for a period of one (1) year from the date of original purchase when delivered to you in new condition in its original container or (b) for ninety (90) days from the date of original purchase for refurbished Products. Product returned to a Canon USA repair facility or a Canon USA Authorized Service Facility ("AS'F"), and proven to be defective upon inspection will be (a) repaired utilizing new, remanufactured, repaired and/ or recycled parts (b) exchanged for new or; (c) exchanged for a refurbished Product, as determined by the Canon USA repair facility orthe ASF. Warranty repair orreplacement shall not extend the original warranty period of the Product. A dated proof of purchase is required at the time of warranty service. A copy of your dated bill of sale will satisfy this requirement. This warranty does not cover any accessories, or any consumables, such as paper or ink cartridges, as to which there shall be no warranty or replacement. This limited warranty shall only apply if the Product is used in conjunction with compatible computers, peripheral equipment and software. Canon USA shall have no responsibility for such items except for compatible Canon brand peripheral equipment covered by a separate warranty ("Separate Warranty"). Repairs of such Canon brand peripheral equipment shall be governed by the terms of the Separate Warranty. Non-Canon brand equipment and software that may be distributed with the Product are sold "as is" and without warranty of any kind by Canon USA, including any implied warranty regarding merchantability or fitness for a particular purpose, and all such warranties are disclaimed. The sole warranty, if any, with respect to such non-Canon brand items is given by the manufacturer or producer thereof. This limited warranty covers all defects encountered in normal use of the Product and does not apply in the following cases: (a) Loss of or damage to the Product due to abuse, neglect, mishandling, improper packaging by you, alteration, accident, electrical current fluctuations, improper use, failure to follow operating or maintenance instructions in, or environmental conditions prescribed in, Canon USA's user's manual or other documentation, or services performed by someone other than a Canon USA repair facility or ASF. Without limiting the foregoing, dropping the Product, scratches, and abrasions will be presumed to have resulted from misuse, abuse or failure to operate the Product as set forth in the user's manual or other documentation for the Product. (b) Use of parts, media, software or supplies (other than those sold by Canon USA), including non-Canon ink cartridges or refilled ink cartridges, that cause damage to the Product or cause abnormally frequent service calls or service problems. (c) If the product has had its serial number or dating defaced, altered or removed. ANY SYSTEM SOFTWARI: (WHETHER FACTORY LOADED ON THE PRODUCT OR CONTAINED ON THE SOFTWARE DISKETIES OR CD-ROMS ENCLOSED WITH, OR ACCOMPANYING, THE PRODUCn, AND ANY UTILITY SOFTWARE, DISTRIBUTED WITH OR FOR THE PRODUCT, IS SOLD "AS IS" AND WITHOUT WARRANTY BY CANON USA. THE SOLE WARRANTY WITH RESPECT TO SUCH SOFTWARE IS CONTAINED IN THE SOFTWARE MANUFACTURER'S LICENSE AGREEMENT DISTRIBUTED THEREWITH, INCLUDING ANY LIMITATIONS AND DISCLAIMERS THEREON. PLEASE CONTACT CANON USA IMMEDIATELY IF YOU HAVE NOT RECEIVED A COPY OF THE SOFTWARE MANUFACTURER'S LICENSE AGREEMENT. NO IMPLIED WARRANTY, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILTY OR FITNESS FOR A PARTICULAR PURPOSE, APPLIES TO THE PRODUCT AFTER THE APPLICABLE PERIOD OF THE EXPRESS LIMITED WARRANTY STATED ABOVE, AND NO OTHER EXPRESS WARRANTY OR GUARANTY, EXCEPT AS MENTIONED ABOVE, GIVEN BY ANY PERSON OR ENTITY WITH RESPECT TO THE PRODUCT SHALL BIND CANON USA, OR ITS ASF. (SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU.) CANON USA SHALL NOT BE LIABLE FOR LOSS OF REVENUES OR PROFITS, INCONVENIENCE, EXPENSE FOR SUBSTITUTE EQUIPMENT OR SERVICE, STORAGE CHARGES, LOSS OR CORRUPTION OF DATA, OR ANY OTHER SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES CAUSED BY THE USE, MISUSE, OR INABILITY TO USE THE PROUDCT REGARDLESS OF THE LEGAL THEORY ON WHICH THE CLAIM IS BASED, AND EVEN IF CANON USA OR ITS ASF HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. NOR SHALL RECOVERY OF ANY KIND AGAINST CANON USA OR ITS ASF BE GREATER IN AMOUNT THAN THE PURCHASE PRICE OF THE PRODUCT CAUSING THE ALLEGED DAMAGE. WITHOUT LIMITING THE FOREGOING, YOU ASSUME ALL RISK AND LIABILITY FOR LOSS, DAMAGE OR INJURY TO YOU AND YOUR PROPERTY AND TO OTHERS AND THEIR PROPERTY ARISING OUT OF THE POSSESSION, USE, MISUSE, OR INABILITY TO USE THE PRODUCT SOLD BY CANON USA NOT CAUSED SOLELY AND DIRECTLY BY THE NEGLIGENCE OF CANON USA, OR ITS ASF. (SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE EXCLUSION OR LIMITATION MAY NOT APPLY TO YOU.) THIS LIMITED WARRANTY SHALL NOT EXTEND TO ANYONE OTHER THAN THE ORIGINAL PURCHASER OF THE PRODUCT OR THE PERSON FOR WHOM IT WAS PURCHASED AS A GIFT, AND STATES YOUR EXCLUSIVE REMEDY.