Comcast Inicio Operation & User’s Manual

Pair Remote for “Aim Anywhere” Control Turn On Your Remote Control Your TV’s Power and Volume Remote with Aim Anywhere Start 1 Press and hold the Setup button (about 3 seconds) until the Status LED changes from red to green. Press the XFINITY button. Follow the on-screen instructions to enter the 3-digit code that appears. Once the code is correctly entered, your XFINITY Remote is paired with the device. Pick up your remote and remove the “Pull” tab (on back) by pulling away from the remote. The Status LED will blink green four times as the remote powers up (about 5 seconds). Turn on your TV. Turn on your set-top box. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not used in accordance with the instructions, may cause harmful interference to radio communications. There is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase or decrease the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that which the receiver is connected. • Consult the dealer or an experienced remote control/ TV technician for help. • It is strongly recommended that the TV be plugged into a separate wall outlet. The user is cautioned that changes and modifications made to this equipment without the approval of the manufacturer could void the user’s authority to operate this equipment. This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Using the list on the right, find the first 5-digit code for your TV manufacturer. Press and hold the Setup button (about 3 seconds) until the Status LED changes from red to green. Enter in the first 5-digit code for your TV manufacturer. The Status LED should blink green twice. Verify that the code was accepted by using your remote to adjust volume and turn the TV on and off. A B C A B C A B C D 3 2 4 Status LED All Power Search Discover content by channel, program or key words. Number Keys Use predicitve text (T9) to quickly search for content. TV Input Changes to the next available input on your TV (if programmed in Step 4) TV Power XFINITY / Menu Access Guide, Saved, XFINITY On Demand, Apps, Search and Settings. Setup Program remote for Aim Anywhere or to control your TV or audio device. Control your set-top box without having to point at it, even when it is inside a cabinet or entertainment center. Your remote arrives with the AA batteries already installed, but not activated. Here is how to power it on for the first time. Need to remove Aim Anywhere control? Press and hold the Setup button on the remote until the status LED changes from red to green. Press A on the remote. If the status LED blinks green twice, you have successfully removed Aim Anywhere. Not working? Make sure the battery tab from your remote is removed, your TV is on and you are entering the correct 3-digit code on your TV screen. Not working? Try the second code listed. Still not working? Visit xfinity.com/remotes for a complete list of manufacturer codes. Back If your code isn’t listed or you would like to control an audio device, visit xfinity.com/remotes. Popular Manufacturer Codes LG 10178, 11265 Panasonic 10051, 10250 Samsung 10812, 10060 Sanyo 10154, 10159 Sony 10000, 11100 Sharp 10093, 10165 Toshiba 10156, 11156 Vizio 11758, 11756 FCC Compliance Statement

controlar un equipo de audio, visite xfinity.com/ remotes. Códigos de fabricantes más comunes LG 10178, 11265 Panasonic 10051, 10250 Samsung 10812, 10060 Sanyo 10154, 10159 Sony 10000, 11100 Sharp 10093, 10165 Toshiba 10156, 11156 Vizio 11758, 11756 ¿No funciona? Pruebe el segundo código de la lista. ¿Aún no funciona? Visite xfinity.com/ remotes para una obtener lista completa de códigos de fabricantes. ¿Necesita eliminar el control Aim Anywhere? Mantenga presionado el botón Setup del control remoto hasta que la luz LED de estado cambie de rojo a verde. Presione A en el control remoto. Si la luz LED de estado parpadea dos veces en color verde, eliminó satisfactoriamente el control Aim Anywhere. ¿No funciona? Asegúrese de que ha retirado la pestaña junto a las baterías de su control remoto, su TV está encendido y ha ingresado el código de 3 dígitos correctamente en la pantalla del televisor. Conozca su control remoto Sincronice el control remoto para controlar “Aim Anywhere” Encienda su control remoto Controle el encendido y el volumen del televisor Control remoto con Aim Anywhere Inicio 1 Mantenga presionado el botón Setup unos 3 segundos, hasta que la luz LED de estado cambie de rojo a verde. Presione el botón XFINITY. Siga las instrucciones en pantalla para ingresar el código de 3 dígitos que aparece. Una vez que el código se haya ingresado correctamente, su control remoto de XFINITY queda sincronizado con el aparato. Tome su control remoto y quite la pestaña “Pull” (situada en la parte posterior) separándola del control remoto. La luz LED de estado parpadeará en verde cuatro veces mientras se enciende el control remoto (unos 5 segundos). Encienda su televisor. Encienda su decodificador. Encuentre en la lista de la derecha el primer código de 5 dígitos correspondiente al fabricante de su televisor. Mantenga presionado el botón Setup unos 3 segundos, hasta que la luz LED de estado cambie de rojo a verde. Ingrese el primer código de 5 dígitos correspondiente al fabricante. La luz LED de estado debe parpadear en color verde dos veces. Verifique que el código ha sido aceptado usando su control remoto para ajustar el volumen y encender y apagar el televisor. A B C A B C A B C D 3 2 4 Luz LED de estado Todo encendido Buscar Busque contenido por canal, programa o palabras clave. Teclas de números Use el texto predictivo (T9) para buscar contenido con rapidez/facilidad. Entrada de TV ​Cambios para la siguiente entrada disponible en su televisor (si se programó en el paso 4). Encendido de televisor XFINITY/Menú Acceda a guía, guardados, XFINITY On Demand, Apps, búsqueda y configuración. Configuración ​Programe el control remoto para Aim Anywhere o controle su TV o equipo de audio. Controle su decodificador sin tener que apuntar hacia él, incluso si está dentro de un armario o en un centro de entretenimiento. Su control remoto se le entrega con baterías AA ya instaladas, pero no activado. A continuación se muestra cómo debe encenderlo la primera vez. Back Keep for future reference, but if you decide to toss, please recycle. Get Started Guide v.1.0 Need help? Visit xfinity.com/xtv