CYP CMPRO-U4H4CVE Operation Manual

with LAN Serving Operation Manual Operation Manual

is believed to be accurate. Cypress Technology assumes no responsibility for any infringements of patents or other rights of third parties which may result from its use. Cypress Technology assumes no responsibility for any inaccuracies that may be contained in this document. Cypress also makes no commitment to update or to keep current the information contained in this document. Cypress Technology reserves the right to make improvements to this document and/or product at any time and without notice. COPYRIGHT NOTICE No part of this document may be reproduced, transmitted, transcribed, stored in a retrieval system, or any of its part translated into any language or computer file, in any form or by any means— electronic, mechanical, magnetic, optical, chemical, manual, or otherwise—without express written permission and consent from Cypress Technology. © Copyright 2011 by Cypress Technology. All Rights Reserved. Version 1.1 August 2011 TRADEMARK ACKNOWLEDGMENTS All products or service names mentioned in this document may be trademarks of the companies with which they are associated. HDBaseT™ and the HDBaseT Alliance logo are trademarks of the HDBaseT Alliance.

operate this equipment and before connecting the power supply. Please keep the following in mind as you unpack and install this equipment: • Always follow basic safety precautions to reduce the risk of fire, electrical shock and injury to persons. • To prevent fire or shock hazard, do not expose the unit to rain, moisture or install this product near water. • Never spill liquid of any kind on or into this product. • Never push an object of any kind into this product through any openings or empty slots in the unit, as you may damage parts inside the unit. • Do not attach the power supply cabling to building surfaces. • Use only the supplied power supply unit (PSU). Do not use the PSU if it is damaged. • Do not allow anything to rest on the power cabling or allow any weight to be placed upon it or any person walk on it. • To protect the unit from overheating, do not block any vents or openings in the unit housing that provide ventilation and allow for sufficient space for air to circulate around the unit. REVISION HISTORY VERSION NO. DATE DD/MM/YY SUMMARY OF CHANGE VR0 17/09/14 Preliminary Release VS1 12/01/16 Updated text/diagrams

4. System Requirements����������������������������2 5. Features��������������������������������������������������2 6. Operation Controls and Functions�������3 6.1 Front Panel����������������������������������������3 6.2 Rear Panel�����������������������������������������4 6.3 Remote Control��������������������������������5 6.4 IR Cable Pin Assignment�����������������6 6.5 RS-232 Pin Assignment���������������������6 6.6 RS-232 and Telnet Commands�������7 6.7 RS-232 UART Control�������������������������9 6.8 Telnet Control���������������������������������10 6.9 WebGUI Control�����������������������������12 7. Connection Diagram��������������������������13 8. Specifications��������������������������������������14 8.1 Technical Specification�����������������14 8.2 Input/Output Resolution����������������15 8.3 CAT5e/6/7 Cable Specification���16 9. Acronyms���������������������������������������������16

transmission of video (resolutions up to 4K2K and Full HD), multi- channel digital audio and control via IR, RS-232, Telnet or WebGUI from four high definition sources to four HDBaseT™ outputs over a single CAT5e/6/7 cable (up to 100m at 1080p and 70m at 4K2K) for each output. It supports passthrough of high resolution digital audio formats such as LPCM 7.1CH, Dolby TrueHD, Dolby Digital Plus and DTS-HD Master Audio as well as 3D content that can be displayed when connecting a 3D TV and 3D source. Additionally, the LAN connectivity will allow a 100BaseT network to be served to smart TVs or games consoles. The Power over Cable (PoC) function can power compatible Receivers, providing greater flexibility in installations. 2. APPLICATIONS •  HDMI matrix system •  Video/TV wall display and control •  Security surveillance and control •  Commercial advertising, display and control •  University lecture hall, display and control •  Retail sales and demonstration 3. PACKAGE CONTENTS •  1×4 by 4 HDMI 4K UHD over CAT5e/6/7 Matrix •  1×IR Extender •  1×IR Blaster •  1×24 V/3.75 A DC Power Adaptor •  1×Power Cord •  1×Remote Control with Battery •  1×Set of Rack Ears •  1×Operation Manual

•  HDMI equipped source devices, connect with HDMI cables or DVI equipped source, connect with DVI to HDMI cables •  HDMI equipped displays (TVs or monitors) or HDMI equipped AV Receivers, connect with HDMI cables •  Industry standard CAT5e/6/7 cables •  Compatible HDBaseT™ receivers such as CH-507RX 5. FEATURES •  HDMI, HDCP1.1 and DVI compliant •  Supports HDMI 3D features for compatible sources and displays •  Supports resolutions from VGA to WUXGA and 4K2K @50/60 (YUV 420) dependent upon the output display’s resolution capabilities •  Supports distances up to 100 meters at 1080p and 70 meters at 4K2K through CAT5e/6/7 cables •  Supports HDMI input/output cable lengths up to 10 meters at 1080p (8-bit/12-bit resolution) or 5 meters at 4K2K resolution •  Supports bi-directional IR from the input and output locations •  Supports control of the matrix via RS-232, remote control, on-panel control and IP Control (Telnet/WebGUI) •  1U size design •  Supports external and internal EDID settings •  Supports passthrough of LPCM 7.1CH, Dolby TrueHD, Dolby Digital Plus and DTS-HD Master Audio •  Supports LAN serving to compatible HDBaseT receivers •  Supports Power-over-Cable (PoC) to compatible HDBaseT receivers Note: 1. Do not connect the CAT5e/6/7 output of the matrix to the receiver's LAN port. 2. The PoC function is designed for powering compatible receiver units only, non-PoC receivers will need their own power supply. Receivers of another brand may not be compatible. 3. Please do not connect more than one active Ethernet link to the Matrix system, doing so may trigger the unit to shut down.

6.1 Front Panel 4X4 HDMI MATRIX OVER CAT5e/6/7 POWER LOCK MENU A/1 B/2 C/3 D/4 OUT IN 1 2 3 4 5 6 1 LCM: Displays information about the input and output settings. 2 IR RECEIVE WINDOW: Accepts the remote control signal for this unit only. 3 POWER: Press this button to power the unit on/off. The LED will illuminate green when the power is on, red when it is in 'Standby' mode. 4 LOCK: Press this button to lock all the buttons on the panel; press again to unlock. The LED will illuminate when locked. 5 MENU: Press this button to access the LCM menu system, from here EDID settings can be managed and IP system settings can be displayed. 6 A~D/1~4 and OUT/IN: Press the OUT or IN button to select the output or input mode and then press the required number button to confirm the selection. For example, if outputs A and B need to be set to input 1 and outputs C and D need to be set to input 2, then the following sequence of button presses need to be performed: Press: OUTABIN1MENU, and then press: OUTCDIN2MENU. Note: If the MENU button is not pressed the selection will not be changed.

IR OUT IR IN ALL RS232 IP & ETHERNET SERVICE 1 IR IN IR OUT 2 IR IN IR OUT 3 IR IN IR OUT 4 IR IN IR OUT HDMI IN 1 HDMI IN 2 HDMI IN 3 HDMI IN 4 DC 24V 1 2 3 4 V+ GND GND GND V+ CAT5e/6/7 OUT CAT5e/6/7 OUT CAT5e/6/7 OUT C B A D CAT5e/6/7 OUT 11 2 1 3 7 9 4 8 6 5 1 RS-232: Connect to a PC or RS-232 control system with a D-sub 9-pin cable for the transmission of RS-232 commands. Note: This unit has a routable RS-232 function that can route commands sent to the matrix to all receivers or accept matrix control commands from connected receivers. In order for the receivers to send commands to control the matrix, a null modern cable/adaptor is required (see Section 6.7 for details). 2 IP & ETHERNET: This port is the link for Telnet or WebGUI controls, connect to an active Ethernet network with an RJ45 terminated cable (see Sections 6.8 and 6.9 for details). Warning: Please do not connect more than one active Ethernet link to the Matrix system. 3 SERVICE: Manufacturer use only. 4 CAT5e/6/7 OUT A~D: Connect the CAT outputs to the CAT input port of compatible receiver units with a single CAT5e/6/7 cable for HDMI Audio/Video, IR/RS-232 control signal transmission and Ethernet/LAN sharing (dependent on receiver capabilities). Warning: Please do not connect the CAT5e/6/7 output of the matrix to the receiver's LAN port. 5 IR IN 1~4: Connect the IR Extenders for IR signal reception. Ensure that the remote being used is within the direct line-of-sight of the IR extender. The signal received will be transmitted from the IR OUT of the selected receiver unit. IR OUT 1~4: Connect to the IR Blasters for IR signal transmission. Place the IR blaster in direct line-of-sight of the equipment to be controlled. It will transmit the IR signal received from IR extenders connected to the matrix or receivers according to the selected input. 6 HDMI IN 1~4: Connect to HDMI/DVI source devices such as DVD players or Set-top boxes with HDMI cables or DVI to HDMI cables.

source/input location. Place the IR Blaster in direct line-of-sight of the equipment to be controlled. It will transmit all IR signals received by any IR extenders connected to receiver units. 8 ALL IR IN: Connect an IR Extender for IR signal reception. Ensure that remote being used is within the direct line-of-sight of the IR extender. IR signals received will transmitted by all IR blasters connected to the receiver units. 9 DC 24V: Plug the 24 V DC power supply into the unit and connect the adaptor to an AC outlet. 6.3 Remote Control 1 POWER: Press this button to switch the unit ON or to put it into standby mode 2 IN: Input selection 1 to 4. Press to select the required input setting. 3 OUT: Output selection A to D. Press to select the required output setting. 1 2 3 1 A B 2 C 3 4 D CR-121 IN OUT

3 1 2 3 2 1 IR Blaster Power IR Signal NC IR Signal Power Grounding IR Extender 6.5 RS-232 Pin Assignment MATRIX ► ◄ REMOTE CONTROL CONSOLE Pin Assignment Pin Assignment 1 NC 1 NC 2 Tx 2 Rx 3 Rx 3 Tx 4 NC 4 NC 5 GND 5 GND 6 NC 6 NC 7 NC 7 NC 8 NC 8 NC 9 NC 9 NC Baud Rate: 19200 bps Data Bit: 8-bit Parity: None Stop Bit: 1-bit Flow Control: None

COMMAND DESCRIPTION A1~A4 Set output A to input 1~4 B1~B4 Set output B to input 1~4 C1~C4 Set output C to input 1~4 D1~D4 Set output D to input 1~4 AB…1~AB…4 Set output A~D to input 1~4 simultaneously SETIP Set the IP, Subnet and Gateway configuration (Static IP) RSTIP Reset IP configuration to default values (DHCP) IPCONFIG Show the current IP configuration P0 Power off P1 Power on STORE 01~04 Store the current input and output connections (01~04) PRESET 01~04 Recall the stored input and output connections (01~04) SHOW 01~04 Show the input and output of the sotred connections (01~04) NAME N1 N2 Name the stored input and output connections (N1=01~04) less than 8 characters (N2=A~H) I1~I4 Set all outputs to input 1~4 ST Show the current matrix state and firmware version RS Reset the system to A1, B2, C3, D4 EM Set the EDID mode to 1 (STD) or 2 (TV)

to 1~6 (1=9600bps, 2=14400bps, 3=19200bps, 4=38400bps, 5=57600bps, 6=115200bps) UARTBAUD? Show the UART Baud rate of all outputs UARTSW1~4 Set the UART routing to output A, B, C or D and allow the matrix to send RS-232 commands to devices connected to the receivers UARTSW0 Set the UART routing to MCU and restore RS-232 control of the Matrix UARTSW? Show the UART routing status ? Show all available commands HELP Show all available commands QUIT Exit (Telnet only) Note: 1. Commands will not be executed unless followed by a carriage return. Commands are not case-sensitive. 2. STD EDID supports EDID settings of 1080p video/2CH audio. TV EDID supports EDID settings of the display connected to Output A.

IR OUT IR IN ALL RS232 IP & ETHERNET SERVICE 1 IR IN IR OUT 2 IR IN IR OUT 3 IR IN IR OUT 4 IR IN IR OUT HDMI IN 1 HDMI IN 2 HDMI IN 3 HDMI IN 4 DC 24V 1 2 3 4 V+ GND GND GND V+ CAT5e/6/7 OUT CAT5e/6/7 OUT CAT5e/6/7 OUT C B A D CAT5e/6/7 OUT IR OUT IR IN ALL RS232 IP & ETHERNET SERVICE 1 IR IN IR OUT 2 IR IN IR OUT 3 IR IN IR OUT 4 IR IN IR OUT HDMI IN 1 HDMI IN 2 HDMI IN 3 HDMI IN 4 DC 24V 1 2 3 4 V+ GND GND GND V+ CAT5e/6/7 OUT CAT5e/6/7 OUT CAT5e/6/7 OUT C B A D CAT5e/6/7 OUT IR OUT IR IN ALL RS232 IP & ETHERNET SERVICE 1 IR IN IR OUT 2 IR IN IR OUT 3 IR IN IR OUT 4 IR IN IR OUT HDMI IN 1 HDMI IN 2 HDMI IN 3 HDMI IN 4 DC 24V 1 2 3 4 V+ GND GND GND V+ CAT5e/6/7 OUT CAT5e/6/7 OUT CAT5e/6/7 OUT C B A D CAT5e/6/7 OUT IR OUT IR IN ALL RS232 IP & ETHERNET SERVICE 1 IR IN IR OUT 2 IR IN IR OUT 3 IR IN IR OUT 4 IR IN IR OUT HDMI IN 1 HDMI IN 2 HDMI IN 3 HDMI IN 4 DC 24V 1 2 3 4 V+ GND GND GND V+ CAT5e/6/7 OUT CAT5e/6/7 OUT CAT5e/6/7 OUT C B A D CAT5e/6/7 OUT IR OUT IR IN ALL RS232 IP & ETHERNET SERVICE 1 IR IN IR OUT 2 IR IN IR OUT 3 IR IN IR OUT 4 IR IN IR OUT HDMI IN 1 HDMI IN 2 HDMI IN 3 HDMI IN 4 DC 24V 1 2 3 4 V+ GND GND GND V+ CAT5e/6/7 OUT CAT5e/6/7 OUT CAT5e/6/7 OUT C B A D CAT5e/6/7 OUT RX RS-232 Out LAN HDMI Out CAT5e/6/7 to HDMI with LAN/IR/RS232 Receiver RX RS-232 Out LAN HDMI Out CAT5e/6/7 to HDMI with LAN/IR/RS232 Receiver RX RS-232 Out LAN HDMI Out CAT5e/6/7 to HDMI with LAN/IR/RS232 Receiver RX RS-232 Out LAN HDMI Out CAT5e/6/7 to HDMI with LAN/IR/RS232 Receiver Note: This command allows RS-232 control of the Matrix. Note: This command allows RS-232 control of the device attached to RS-232 output of Receiver connected to Output A. Note: This command allows RS-232 control of the device attached to RS-232 output of Receiver connected to Output B. Note: This command allows RS-232 control of the device attached to RS-232 output of Receiver connected to Output C. Note: This command allows RS-232 control of the device attached to RS-232 output of Receiver connected to Output D. UARTSW0 RS-232 Controlled Device RS-232 Controlled Device RS-232 Controlled Device RS-232 Controlled Device UARTSW1 UARTSW2 UARTSW3 UARTSW4

Before attempting to use the telnet control, please ensure that both the Matrix (via the 'IP & ETHERNET' port) and the PC/Laptop are connected to the same active network. To access the telnet control in Windows 7, click on the 'Start' menu and type "cmd" in the Search field then press enter. Under Windows XP go to the 'Start' menu and click on 'Run', type "cmd' with then press enter. Under Mac OS X, go to Go→Applications→Utilities→Terminal. See below for reference. Once in the command line interface (CLI) type "TELNET", then the IP address of the unit and '23', then hit enter. Note: The IP address of the Matrix can be displayed on the unit's LCM monitor by pressing the Menu button twice.

to list the available commands. Type "IPCONFIG" to show all IP configurations. To reset the IP, type "RSTIP" and to use a set static IP, type "SETIP" (For a full list of commands, see Section 6.7). Note: Commands will not be executed unless followed by a carriage return. Commands are not case-sensitive. If the IP is changed then the IP Address required for Telnet access will also change accordingly.

On a PC/Laptop that is connected to the same active network as the Matrix, open a web browser and type the unit's IP address on the web address entry bar. The browser will display the unit's status, control and user setting pages. Click on the 'Control' tab to control power, input/output ports, EDID and reset mode. Click on the 'User Setting' tab allows you to reset the IP configuration. The system will ask for a reboot of the unit when any of the settings are changed. The IP address needed to access the WebGUI control will also need to be changed accordingly on the web address entry bar.

IR OUT IR IN ALL RS232 IP & ETHERNET SERVICE 1 IR IN IR OUT 2 IR IN IR OUT 3 IR IN IR OUT 4 IR IN IR OUT HDMI IN 1 HDMI IN 2 HDMI IN 3 HDMI IN 4 DC 24V 1 2 3 4 V+ GND GND GND V+ CAT5e/6/7 OUT CAT5e/6/7 OUT CAT5e/6/7 OUT C B A D CAT5e/6/7 OUT RX RX RX 1 2 3 4 RS-232 Out LAN HDMI Out CAT5e/6/7 to HDMI with LAN/IR/RS232 Receiver RS-232 Out LAN HDMI Out CAT5e/6/7 to HDMI with LAN/IR/RS232 Receiver RS-232 Out LAN HDMI Out CAT5e/6/7 to HDMI with LAN/IR/RS232 Receiver RS-232 Out LAN HDMI Out CAT5e/6/7 to HDMI with LAN/IR/RS232 Receiver RX IR EXTENDER 7m 3m 3m 60° m IR BLASTER 1.5m 60° Blu-ray Player RS-232 Equipped PC or Control System CAT5e/6/7 Outputs Power Supply Internet Connected Network Router IR In All IR Out All Media Server Satellite Receiver Set-top Box HDMI Input HDMI Input HDMI Input HDMI Input IR In/ Out IR In/ Out IR In/ Out IR In/ Out

Video Bandwidth 340 MHz/10.2 Gbps Input Ports 4×HDMI, 5×IR Extender, 1×RS-232, 1×RJ-45 (Control), 1×Mini USB Type B (For firmware updated only) Output Ports 4×CAT5e/6/7, 5×IR Blaster Supported HDMI Cable Lengths 10m@1080p, 5m@4K2K (Input/output) ESD Protection Human-body Model: ± 8kV (Air-gap discharge) ± 4kV (Contact discharge) Power Supply 24 V/3.75 A DC (US/EU standards, CE/FCC/ UL certified) Dimensions 436 mm (W)×249 mm (D)×44 mm (H)/Jacks Excluded 436 mm (W)×256.2 mm (D)×48 mm (H)/ Jacks Included Weight 3352 g Chassis Material Metal Color Black Operating Temperature 0 ºC~40 ºC/32 ºF~104 ºF Storage Temperature −20 ºC~60 ºC/−4 ºF~140 ºF Relative Humidity 20~90 % RH (non-condensing) Power Consumption 66 W

SUPPORTED RESOLUTION INPUT OUTPUT 640×480@60/72/75/85   800×600@56/60/72/75/85   1024×768@60/70/75/85   1280×720@60   1280×1024@60   1600×1200@60   1920×1200@60RB   3840×2160p@24/25/30   4096×2160p@24   4096×2160p@50/60 (YUV 420)   480i/576i   480p/576p   720p@50/60   1080i@50/60   1080p@50/60   1080p@24/25/30  

Cable Type Range Pixel Clock Rate Video Data Rate Supported Video CAT5e/6/7 100 m ≤225 MHz ≤5.3 Gbps (HD Video) Up to 1080p@60 Hz, 36-bit 3D (data rates lower than 5.3 Gbps or below 225 MHz TMDS clock). 9. ACRONYMS ACRONYM COMPLETE TERM CLI Command Line Interface DTS Digital Theater System DVI Digital Visual Interface EDID Extended Display Identification Data GUI Graphical User Interface HDCP High-bandwidth Digital Content Protection HDMI High-Definition Multimedia Interface HDTV High-Definition Television LCM Liquid Crystal Module USB Universal Serial Bus VGA Video Graphics Array WUXGA Widescreen Ultra Extended Graphics Array