D-Link DIR 635 B3 Operation & User’s Manual

D-Link reserves the right to revise this publication and to make changes in the content hereof without obligation to notify any person or organization of such revisions or changes. Manual Revisions Other Reference Document If you use the USB port of this router as a network port to share your USB hard drive, flash drive or printer, read the SharePortTM Network USB Utility Manual for additional instructions. Trademarks D-Link and the D-Link logo are trademarks or registered trademarks of D-Link Corporation or its overseas subsidiaries. All other company or product names mentioned herein are trademarks or registered trademarks of their respective companies. Copyright © 2009 by D-Link Corporation All rights reserved. This publication may not be reproduced, in whole or in part, without prior expressed written permission from D-Link Corporation. Revision Date Description 2.0 December 23, 2008 Added SharePortTM Network USB Utility support Preface Preface

Table of Contents Preface............................................................................i Manual Revisions................................................................i Trademarks..........................................................................i Product Overview.........................................................1 Package Contents...............................................................1 System Requirements........................................................1 Introduction........................................................................2 Features..............................................................................3 Hardware Overview............................................................4 Connections.................................................................4 LEDs............................................................................5 Installation.....................................................................6 Before you Begin................................................................6 Wireless Installation Considerations...................................7 Connect to Cable/DSL/Satellite Modem..............................8 Connect to Another Router.................................................9 Getting Started.................................................................11 Configuration..............................................................12 Web-based Configuration Utility.......................................12 Setup Wizard..............................................................13 Manual Internet Connection Setup.............................17 Dynamic (Cable)....................................................18 PPPoE (DSL).........................................................19 PPTP......................................................................20 L2TP......................................................................22 Static (assigned by ISP).........................................24 3G Mobile Connection............................................25 Wireless Settings.......................................................26 Manual Wireless Settings...........................................27 Network Settings........................................................29 Router Settings......................................................30 DHCP Server Settings............................................29 DHCP Reservation.................................................31 USB Settings..............................................................32 Virtual Server.............................................................33 Port Forwarding.........................................................35 Application Rules.......................................................36 QoS Engine................................................................37 Network Filters...........................................................39 Access Control...........................................................40 Access Control Wizard...........................................41 Website Filters...........................................................43 Inbound Filters...........................................................44 Firewall Settings.........................................................44 ALG Configuration......................................................46 Routing......................................................................47 Advanced Wireless Settings.......................................48 WISH Settings............................................................49 Wi-Fi Protected Setup (WPS).....................................51 Advanced Network Settings.......................................53 Table of Contents

Table of Contents Administrator Settings...............................................54 Time Settings.............................................................55 SysLog.......................................................................56 Email Settings............................................................57 System Settings.........................................................58 Update Firmware........................................................59 DDNS.........................................................................60 System Check............................................................61 Schedules..................................................................62 Device Information.....................................................63 Log.............................................................................64 Statistics....................................................................65 Internet Sessions.......................................................65 Wireless.....................................................................66 WISH Settings............................................................66 Support......................................................................67 Wireless Security........................................................68 What is WPA?...................................................................68 Wireless Security Setup Wizard........................................69 Add Wireless Device with WPS Wizard............................71 Configure WPA-Personal (PSK)........................................72 Configure WPA-Enterprise (RADIUS)...............................73 Connect to a Wireless Network.................................75 Using Windows Vista®......................................................75 Configure Wireless Security.......................................76 Connect Using WCN 2.0 in Windows Vista® ..............78 Using Windows® XP.........................................................79 Configure WPA-PSK...................................................80 Troubleshooting..........................................................82 Wireless Basics..........................................................86 What is Wireless?.............................................................86 Tips..................................................................................89 Wireless Modes................................................................90 Networking Basics.....................................................91 Check your IP address......................................................91 Statically Assign an IP address.........................................92 Technical Specifications............................................93

Section 1 - Product Overview • D-Link DIR-635 RangeBooster N™ 650 • 3 Detachable Antennas • Power Adapter • CAT5 Ethernet Cable • CD-ROM with Installation Wizard and User Manual System Requirements • Ethernet-based Cable or DSL Modem • Computers with Windows®, Macintosh®, or Linux-based operating systems with an installed Ethernet adapter • Internet Explorer Version 6.0, or Firefox 1.5 and above (for configuration) • Installation Wizard requires Windows® XP with Service Pack 2 or Vista® Package Contents Note: Using a power supply with a different voltage rating than the one included with the DIR-635 will cause damage and void the warranty for this product.

Section 1 - Product Overview Introduction TOTAL PERFORMANCE Combines award winning router features and Draft 802.11n wireless technology to provide the best wireless performance TOTAL SECURITY The most complete set of security features including Active Firewall and WPA2 to protect your network against outside intruders TOTAL COVERAGE Provides greater wireless signal rates even at farther distances for best-in-class Whole Home Coverage. ULTIMATE PERFORMANCE The D-Link RangeBooster N™ 650 (DIR-635) is a draft 802.11n compliant device that delivers real world performance which is many times faster than an 802.11g wireless connection (also faster than a 100Mbps wired Ethernet connection). Create a secure wireless network to share photos, files, music, video, printers, and network storage throughout your home. Connect the RangeBooster N™ 650 to a cable or DSL modem and share your high-speed Internet access with everyone on the network. In addition, this Router includes a Quality of Service (QoS) engine that keeps digital phone calls (VoIP) and online gaming smooth and responsive, providing a better Internet experience. EXTENDED WHOLE HOME COVERAGE Powered by RangeBooster N™ technology, this high performance router provides superior Whole Home Coverage while reducing dead spots. The RangeBooster N™ 650 is designed for use in bigger homes and for users who demand higher performance networking. Add a RangeBooster N™ 650 notebook or desktop adapter and stay connected to your network from virtually anywhere in your home. TOTAL NETWORK SECURITY The RangeBooster N™ 650 supports all of the latest wireless security features to prevent unauthorized access, be it from over the wireless network or from the Internet. Support for WPA/WPA2 and WEP standards ensure that you’ll be able to use the best possible encryption method, regardless of your client devices. In addition, this RangeBooster N™ 650 utilizes dual active firewalls (SPI and NAT) to prevent potential attacks from across the Internet. * Maximum wireless signal rate derived from IEEE Standard 802.11g and Draft 802.11n specifications. Actual data throughput will vary. Network conditions and environmental factors, including volume of network traffic, building materials and construction, and network overhead, lower actual data throughput rate. Environmental conditions will adversely affect wireless signal range.

Section 1 - Product Overview • Faster Wireless Networking - The DIR-635 provides very high speed* wireless connection with other 802.11n wireless clients. This capability allows users to participate in real-time activities online, such as video streaming, online gaming, and real-time audio. The performance of this 802.11n wireless router gives you the freedom of wireless networking at speeds many times faster than 802.11g. • Compatible with 802.11b and 802.11g Devices - The DIR-635 is still fully compatible with the IEEE 802.11b standard, so it can connect with existing 802.11b and g devices. • Advanced Firewall Features - The Web-based user interface displays a number of advanced network management features including: • Content Filtering - Easily applied content filtering based on MAC Address, URL, and/or Domain Name. • Filter Scheduling - These filters can be scheduled to be active on certain days or for a duration of hours or minutes. • Secure Multiple/Concurrent Sessions - The DIR-635 can pass through VPN sessions. It supports multiple and concurrent IPSec and PPTP sessions, so users behind the DIR-635 can securely access corporate networks. • User-friendly Setup Wizard - Through its easy-to-use Web-based user interface, the DIR-635 lets you control what information is accessible to those on the wireless network, whether from the Internet or from your company’s server. Configure your router to your specific settings within minutes. * Maximum wireless signal rate derived from IEEE Standard 802.11g and Draft 802.11n specifications. Actual data throughput will vary. Network conditions and environmental factors, including volume of network traffic, building materials and construction, and network overhead, lower actual data throughput rate. Environmental conditions will adversely affect wireless signal range. Features

Section 1 - Product Overview USB Connect a USB flash drive to configure WLAN settings via WCN or a USB hard drive or printer for sharing over the network, or a D-Link 3G adapter for Internet connection. Reset Restores the router to its original factory default settings. LAN Ports (1-4) Connect Ethernet devices such as computers, switches, and hubs. Internet Port The auto MDI/MDIX Internet port is for an Ethernet connection or DSL modem. Power Receptor Receptor for the supplied power adapter. Hardware Overview Connections

Section 1 - Product Overview Hardware Overview LEDs WLAN LED A solid light indicates that the wireless segment is ready. The LED blinks during wireless data transmission. Status LED A blinking light indicates that the DIR-635 is ready. Internet LED A solid light indicates connection on the Internet port. This LED blinks during data transmission. Power LED A solid light indicates a proper connection to the power supply. Local Network LEDs A solid light indicates a connection to an Ethernet-enabled computer on ports 1-4. The LED blinks during data transmission. USB LED A solid light indicates that a connection is eastablished with the USB device.

Section 2 - Installation Before you Begin Installation This section will walk you through the installation process. Placement of the router is very important. Do not place the router in an enclosed area such as a closet, cabinet, or in the attic or garage. • Please configure the router with the computer that was last connected directly to your modem. • You can only use the Ethernet port on your modem. If you were using the USB connection before using the router, then you must turn off your modem, disconnect the USB cable and connect an Ethernet cable to the Internet port on the router, and then turn the modem back on. In some cases, you may need to call your ISP to change connection types (USB to Ethernet). • If you have DSL and are connecting via PPPoE, make sure you disable or uninstall any PPPoE software such as WinPoet, Broadjump, or Enternet 300 from your computer or you will not be able to connect to the Internet. • When running the Setup Wizard from the D-Link CD, make sure the computer you are running the CD from is connected to the Internet and online or the wizard will not work. If you have disconnected any hardware, re-connect your computer back to the modem and make sure you are online.

Section 2 - Installation Wireless Installation Considerations The D-Link wireless router lets you access your network using a wireless connection from virtually anywhere within the operating range of your wireless network. Keep in mind, however, that the number, thickness and location of walls, ceilings, or other objects that the wireless signals must pass through, may limit the range. Typical ranges vary depending on the types of materials and background RF (radio frequency) noise in your home or business. The key to maximizing wireless range is to follow these basic guidelines: 1. Keep the number of walls and ceilings between the D-Link router and other network devices to a minimum - each wall or ceiling can reduce your adapter’s range from 3-90 feet (1-30 meters.) Position your devices so that the number of walls or ceilings is minimized. 2. Be aware of the direct line between network devices. A wall that is 1.5 feet thick (.5 meters), at a 45-degree angle appears to be almost 3 feet (1 meter) thick. At a 2-degree angle it looks over 42 feet (14 meters) thick! Position devices so that the signal will travel straight through a wall or ceiling (instead of at an angle) for better reception. 3. A solid metal door or aluminum studs may have a negative effect on range. Try to position access points, wireless routers, and computers so that the signal passes through drywall or open doorways. Materials and objects such as glass, steel, metal, walls with insulation, water (fish tanks), mirrors, file cabinets, brick, and concrete will degrade your wireless signal. 4. Keep your product away (at least 3-6 feet or 1-2 meters) from electrical devices or appliances that generate RF noise. 5. If you are using 2.4GHz cordless phones or X-10 (wireless products such as ceiling fans, lights, and home security systems), your wireless connection may degrade dramatically or drop completely. Make sure your 2.4GHz phone base is as far away from your wireless devices as possible. The base transmits a signal even if the phone in not in use.

Section 2 - Installation If you are connecting the router to a cable/DSL/satellite modem, please follow the steps below: 1. Place the router in an open and central location. Do not plug the power adapter into the router. 2. Turn the power off on your modem. If there is no on/off switch, then unplug the modem’s power adapter. Shut down your computer. 3. Unplug the Ethernet cable (that connects your computer to your modem) from your computer and place it into the Internet port on the router. 4. Plug an Ethernet cable into one of the four LAN ports on the router. Plug the other end into the Ethernet port on your computer. 5. Turn on or plug in your modem. Wait for the modem to boot (about 30 seconds). 6. Plug the power adapter to the router and connect to an outlet or power strip. Wait about 30 seconds for the router to boot. 7. Turn on your computer. 8. Refer to page 12 to configure your new D-Link wireless router using the web-based configuration utility. Connect to Cable/DSL/Satellite Modem

Section 2 - Installation If you are connecting the D-Link router to another router to use as a wireless access point and/or switch, you will have to do the following before connecting the router to your network: • Disable UPnP™ • Disable DHCP • Change the LAN IP address to an available address on your network. The LAN ports on the router cannot accept a DHCP address from your other router. To connect to another router, please follow the steps below: 1. Plug the power into the router. Connect one of your computers to the router (LAN port) using an Ethernet cable. Make sure your IP address on the computer is 192.168.0.xxx (where xxx is between 2 and 254). Please see the Networking Basics section for more information. If you need to change the settings, write down your existing settings before making any changes. In most cases, your computer should be set to receive an IP address automatically in which case you will not have to do anything to your computer. 2. Open a web browser and enter http://192.168.0.1 and press Enter. When the login window appears, set the user name to Admin and leave the password box empty. Click Log In to continue. 3. Click Advanced and then click Advanced Network. Uncheck Enable UPnP and click Save Settings to continue. 4. Click Setup and then click Network Settings. Uncheck Enable DHCP Server and click Save Settings to continue. 5. Under Router Settings, enter an IP address and the subnet mask of your network. Click Save Settings to save your settings. Use this new IP address to access the configuration utility of the router in the future. Close the browser and change your computer’s IP settings back to the original values as mentioned in step 1. Connect to Another Router

Section 2 - Installation 6. Disconnect the Ethernet cable from the router and reconnect your computer to your network. 7. Connect an Ethernet cable in one of the LAN ports of the router and connect it to your other router. Do not plug anything into the Internet (WAN) port of the D-Link router. 8. You may now use the other 3 LAN ports to connect other Ethernet devices and computers. To configure your wireless network, open a web browser and enter the IP address you assigned to the router. Refer to the Configuration and Wireless Security sections for more information on setting up your wireless network.

Section 2 - Installation The DIR-635 includes a Quick Router Setup Wizard CD. Follow the simple steps below to run the Setup Wizard, which guides you quickly through the installation process. Insert the Quick Router Setup Wizard CD in the CD-ROM drive. The step-by-step instructions that follow are shown in Windows® XP. The steps and screens are similar for the other Windows operating systems. If the CD autorun function does not automatically start on your computer, go to Start > Run. In the run box type D:\ Autorun.exe (where D: represents the drive letter of your CD-ROM drive). When the autorun screen appears, click Install Router. Getting Started Note: It is highly recommended that you note down the SSID, Security Key and login password somewhere safe such as such as on the router’s CD holder.

Section 3 - Configuration Configuration This section will show you how to configure your new D-Link wireless router using the web-based configuration utility. Web-based Configuration Utility To access the configuration utility, open a web-browser such as Internet Explorer and enter the IP address of the router (192.168.0.1). Select Admin from the drop-down menu and then enter your password. Leave the password blank, which is the default password. If you get a Page Cannot be Displayed error, please refer to the Troubleshooting section for assistance.

Section 3 - Configuration Setup Wizard Click Launch Internet Connection Setup Wizard to begin. If you want to enter your settings without running the wizard, click Manual Configuration and skip to page 17. Click Next to continue. Create a new password and then click Next to continue.

Section 3 - Configuration Select your time zone from the drop-down menu and then click Next to continue. Select the type of Internet connection you use and then click Next to continue. If you selected Dynamic, you may need to enter the MAC address of the computer that was last connected directly to your modem. If you are currently using that computer, click Clone Your PC’s MAC Address and then click Next to continue. The Host Name is optional but may be required by some ISPs. The default host name is the device name of the router and may be changed.

Section 3 - Configuration If you selected PPPoE, enter your PPPoE username and password. Click Next to continue. Select Static if your ISP assigned you the IP address, subnet mask, gateway, and DNS server addresses. Note: Make sure to remove your PPPoE software from your computer. The software is no longer needed and will not work through a router. If you selected PPTP, enter your PPTP username and password. Click Next to continue. If you selected L2TP, enter your L2TP username and password. Click Next to continue.

Section 3 - Configuration If you selected Static, enter your network settings supplied by your Internet provider. Click Next to continue. Click Connect to save your settings. Click Reboot Now to reboot the router so the new settings can take effect. Once the router is finished rebooting, click Continue. Please allow one or two minutes to connect. Close your browser window and reopen it to test your Internet connection. It may take a few tries to initially connect to the Internet.

Section 3 - Configuration Manual Internet Connection Setup Click Manual Internet Connection Setup to begin. If you want to configure your router to connect to the Internet using the wizard, click Internet Connection Setup Wizard and refer to page 13.

Section 3 - Configuration Select Dynamic IP (DHCP) to obtain IP Address information automatically from your ISP. Select this option if your ISP does not give you any IP numbers to use. This option is commonly used for cable modem services such as Comcast and Cox. The Host Name is optional but may be required by some ISPs. Leave blank if you are not sure. Check the box if you are having problems obtaining an IP address from your ISP. Enter the primary and secondary DNS server IP addresses assigned by your ISP. These addresses are usually obtained automatically from your ISP. Leave at 0.0.0.0 if you did not specifically receive these from your ISP. Maximum Transmission Unit - you may need to change the MTU for optimal performance with your specific ISP. 1500 is the default MTU. The default MAC Address is set to the Internet port’s physical interface MAC address on the Broadband Router. It is not recommended that you change the default MAC address unless required by your ISP. You can use the Clone Your PC’s MAC Address button to replace the Internet port’s MAC address with the MAC address of your Ethernet card. My Internet Connection: Host Name: MAC Address: Dynamic (Cable) Primary/ Secondary DNS Server: MTU: Use Unicasting:

Section 3 - Configuration Select PPPoE (Username/Password) from the drop-down menu. Select Static IP if your ISP assigned you the IP address, subnet mask, gateway, and DNS server addresses. In most cases, select Dynamic. Enter the IP address (Static PPPoE only). Enter your PPPoE user name. Enter your PPPoE password and then retype the password in the next box. Enter the ISP Service Name (optional). Select either Always-on, On-Demand, or Manual. Enter a maximum idle time during which the Internet connection is maintained during inactivity. This function does not apply if you have selected Reconnect Mode as Always on. Enter the Primary and Secondary DNS Server Addresses (Static PPPoE only). You may need to change the MTU (Maximum Transmission Unit) for optimal performance with your specific ISP. 1492 is the default MTU value. The default MAC Address is set to the Internet port’s physical interface MAC address on the Broadband Router. It is not recommended that you change the default MAC address unless required by your ISP. You can use the Clone Your PC’s MAC Address button to replace the Internet port’s MAC address with the MAC address of your Ethernet card. My Internet Connection: Address Mode: IP Address: User Name: Password: Service Name: Reconnection Mode: Maximum Idle Time: DNS Addresses: MTU: MAC Address: Internet Setup PPPoE (DSL) Choose PPPoE (Point to Point Protocol over Ethernet) if your ISP uses a PPPoE connection. Your ISP will provide you with a username and password. This option is typically used for DSL services. Make sure to remove your PPPoE software from your computer. The software is no longer needed and will not work through a router.

Section 3 - Configuration Select Static if your ISP assigned you the IP address, subnet mask, gateway, and DNS server addresses. In most cases, select Dynamic. Enter the IP address (Static PPTP only). Enter the Primary and Secondary DNS Server addresses (Static PPTP only). Enter the Gateway IP Address provided by your ISP. Enter the Server IP provided by your ISP (optional). Enter your PPTP username. Enter your PPTP password and then retype the password in the next box. Select either Always-on, On-Demand, or Manual. Enter a maximum idle time during which the Internet connection is maintained during inactivity. This function does not apply if you have selected Reconnect Mode as Always on. Address Mode: PPTP IP Address: PPTP Subnet Mask: PPTP Gateway: PPTP Server IP: Internet Setup PPTP Choose PPTP (Point-to-Point-Tunneling Protocol ) if your ISP uses a PPTP connection. Your ISP will provide you with a username and password. This option is typically used for DSL services. Username: Password: Reconnect Mode: Maximum Idle Time:

Section 3 - Configuration The DNS server information will be supplied by your ISP (Internet Service Provider.) You may need to change the MTU (Maximum Transmission Unit) for optimal performance with your specific ISP. 1400 is the default MTU value. The default MAC Address is set to the Internet port’s physical interface MAC address on the Broadband Router. It is not recommended that you change the default MAC address unless required by your ISP. You can use the Clone Your PC’s MAC Address button to replace the Internet port’s MAC address with the MAC address of your Ethernet card. DNS Servers: MTU: MAC Address:

Section 3 - Configuration Select Static if your ISP assigned you the IP address, subnet mask, gateway, and DNS server addresses. In most cases, select Dynamic. Enter the L2TP IP address supplied by your ISP (Static only). Enter the Subnet Mask supplied by your ISP (Static only). Enter the Gateway IP Address provided by your ISP. Enter the Server IP provided by your ISP (optional). Enter your L2TP username. Enter your L2TP password and then retype the password in the next box. Select either Always-on, On-Demand, or Manual. Enter a maximum idle time during which the Internet connection is maintained during inactivity. This function does not apply if you have selected Reconnect Mode as Always on. Enter the Primary and Secondary DNS Server Addresses (Static L2TP only). Address Mode: L2TP IP Address: L2TP Subnet Mask: L2TP Gateway: L2TP Server IP: Username: Password: Reconnect Mode: Maximum Idle Time: DNS Servers: Internet Setup L2TP Choose L2TP (Layer 2 Tunneling Protocol) if your ISP uses a L2TP connection. Your ISP will provide you with a username and password. This option is typically used for DSL services.

Section 3 - Configuration MTU: Clone MAC Address: You may need to change the MTU (Maximum Transmission Unit) for optimal performance with your specific ISP. 1400 is the default MTU value. The default MAC Address is set to the Internet port’s physical interface MAC address on the Broadband Router. It is not recommended that you change the default MAC address unless required by your ISP. You can use the Clone Your PC’s MAC Address button to replace the Internet port’s MAC address with the MAC address of your Ethernet card.

Section 3 - Configuration Enter the IP address assigned by your ISP. Enter the Subnet Mask assigned by your ISP. Enter the Gateway assigned by your ISP. The DNS server information will be supplied by your ISP (Internet Service Provider.) You may need to change the MTU (Maximum Transmission Unit) for optimal performance with your specific ISP. 1500 is the default MTU value. The default MAC Address is set to the Internet port’s physical interface MAC address on the Broadband Router. It is not recommended that you change the default MAC address unless required by your ISP. You can use the Clone Your PC’s MAC Address button to replace the Internet port’s MAC address with the MAC address of your Ethernet card. IP Address: Subnet Mask: Default Gateway: DNS Servers: MTU: MAC Address: Internet Setup Static (assigned by ISP) Select Static IP Address if all the Internet port’s IP information is provided to you by your ISP. You will need to enter in the IP address, subnet mask, gateway address, and DNS address(es) provided to you by your ISP. Each IP address entered in the fields must be in the appropriate IP form, which are four octets separated by a dot (x.x.x.x). The router will not accept the IP address if it is not in this format. Internet Setup Static (assigned by ISP) Internet Setup Static (assigned by ISP)

Section 3 - Configuration Internet Setup 3G Mobile Connection If you want to connect your router to the Internet through a 3G mobile service, navigate to USB SETTINGS and select SETUP. The USB SETTINGS screen will display. Select 3G USB Adapter from the My Plug of USB type is field and click Save Settings. The INTERNET CONNECTION TYPE screen will display as seen below: Select your country from the list. Displays the name of your Internet Service Provider (ISP). Enter a username. This field is optional. Enter a password. This field is optional. Enter the dial-up number. Choose the authentication type from the drop-down list. The default setting is Auto. Enter a name for the access point. This field is optional. Select Always-on, On-Demand, or Manual. to reconnect to the network. Enter the maximum idle time during which the Internet connection is maintained during inactivity. This function does not apply if you have selected Reconnect Mode as Always on. You may need to change the MTU (Maximum Transmission Unit) for optimal performance with your specific ISP. 1492 is the default MTU value. Country: ISP: Username: Password: Dial Number: Authentication Protocol: APN: Reconnect Mode: Maximum Idle Time: MTU:

Section 3 - Configuration Wireless Settings If you want to configure the wireless settings on your router using the wizard, click Wireless Security Setup Wizard and refer to page 69. Click Add Wireless Device with WPS if you want to add a wireless device using Wi-Fi Protected Setup (WPS) and refer to page 71. If you want to manually configure the wireless settings on your router click Manual Wireless Network Setup and refer to the next page.

Section 3 - Configuration Check the box to enable the wireless function. If you do not want to use wireless, uncheck the box to disable all the wireless functions. Select the time frame that you would like your wireless network enabled. The schedule may be set to Always. Any schedule you create will be available in the drop-down menu. Click Add New to create a new schedule. Service Set Identifier (SSID) is the name of your wireless network. Create a name using up to 32 characters. The SSID is case-sensitive. Select one of the following: 802.11g Only - Select if all of your wireless clients are 802.11g. Mixed 802.11n and 802.11g - Select if you are using both 802.11n and 802.11g wireless clients. 802.11n Only - Select only if all of your wireless clients are 802.11n. The Auto Channel Scan setting can be selected to allow the DIR-635 to choose the channel with the least amount of interference. Indicates the channel setting for the DIR-635. By default the channel is set to 6. The Channel can be changed to fit the channel setting for an existing wireless network or to customize the wireless network. If you enable Auto Channel Scan, this option will be greyed out. Select the transmit rate. It is strongly suggested to select Best (Auto) for best performance. Enable Wireless: Schedule: Wireless Network Name: 802.11 Mode: Enable Auto Channel Scan: Wireless Channel: Transmission Rate: Manual Wireless Settings

Section 3 - Configuration Select the Channel Width: Auto 20/40 - This is the default setting. Select if you are using both 802.11n and non-802.11n wireless devices. 20MHz - Select if you are not using any 802.11n wireless clients. 40MHz - Select if you are using 802.11n wireless clients only. Select Invisible if you do not want the SSID of your wireless network to be broadcasted by the DIR-635. If Invisible is selected, the SSID of the DIR-635 will not be seen by Site Survey utilities so your wireless clients will have to know the SSID of your DIR-635 in order to connect to it. Refer to page 68 for more information regarding wireless security. Channel Width: Visibility Status: Wireless Security:

Section 3 - Configuration This section will allow you to change the local network settings of the router and to configure the DHCP settings. Network Settings Enter the IP address of the router. The default IP address is 192.168.0.1. If you change the IP address, once you click Apply, you will need to enter the new IP address in your browser to get back into the configuration utility. Enter the Subnet Mask. The default subnet mask is 255.255.255.0. Enter the Domain name (Optional). Uncheck the box to transfer the DNS server information from your ISP to your computers. If checked, your computers will use the router for a DNS server. Router IP Address: Subnet Mask: Local Domain: Enable DNS Relay: Router Settings

Section 3 - Configuration DHCP Server Settings DHCP stands for Dynamic Host Control Protocol. The DIR-635 has a built-in DHCP server. The DHCP Server will automatically assign an IP address to the computers on the LAN/private network. Be sure to set your computers to be DHCP clients by setting their TCP/IP settings to “Obtain an IP Address Automatically.” When you turn your computers on, they will automatically load the proper TCP/IP settings provided by the DIR-635. The DHCP Server will automatically allocate an unused IP address from the IP address pool to the requesting computer. You must specify the starting and ending address of the IP address pool. Check this box to enable the DHCP server on your router. Uncheck to disable this function. Enter the starting and ending IP addresses for the DHCP server’s IP assignment. Note: If you statically (manually) assign IP addresses to your computers or devices, make sure the IP addresses are outside of this range or you may have an IP conflict. The length of time for the IP address lease. Enter the Lease time in minutes. Enable this feature to broadcast your networks DHCP server to LAN/WLAN clients. NetBIOS allows LAN hosts to discover all other computers within the network, enable this feature to allow the DHCP Server to offer NetBIOS configuration settings. Enable this feature to allow WINS information to be learned from the WAN side, disable to allow manual configuration. This feature allows the configuration of a NetBIOS ‘domain’ name under which network hosts operates. This setting has no effect if the ‘Learn NetBIOS information from WAN’ is activated. Select the different type of NetBIOS node; Broadcast only, Point-to-Point, Mixed-mode, and Hybrid. Enter your WINS IP address Enable DHCP Server: DHCP IP Address Range: DHCP Lease Time: Always Broadcast: NetBIOS Announcement: Learn NetBIOS from WAN: NetBIOS Scope: NetBIOS Node: WINS IP Address:

Section 3 - Configuration DHCP Reservation If you want a computer or device to always have the same IP address assigned, you can create a DHCP reservation. The router will assign the IP address only to that computer or device. Note: This IP address must be within the DHCP IP Address Range. Check this box to enable the reservation. Enter the computer name or select from the drop down menu and click <<. Enter the IP address you want to assign to the computer or device. This IP Address must be within the DHCP IP Address Range. Enter the MAC address of the computer or device. If you want to assign an IP address to the computer you are currently on, click this button to populate the fields. Click Save to save your entry. You must click Save Settings at the top to activate your reservations. Enable: Computer Name: IP Address: MAC Address: Copy Your PC’s MAC Address: Save:

Section 3 - Configuration USB Settings Use this section to configure your USB port. There are three configurations to choose from: Network USB, WCN Configuration and 3G USB Adapter. Select one of these three configurations: Network USB, WCN Configuration or 3G USB Adapter. If you select Network USB from the drop-down list, you will need to configure the router’s USB port by running the SharePortTM Network USB Utility from you computer so other users of your network may access the USB device connected to this port. Refer to the manual of this utility for complete instructions. If you select 3G USB Adapter from the drop- down list, you need to connect your router to the Internet through a 3G mobile service. Refer to the Internet Setup 3G Mobile Connection on page 25 for details. Please set the Network USB Detection interval. The router will automatically detect the USB device. USB Settings: Network USB:

Section 3 - Configuration The DIR-635 can be configured as a virtual server so that remote users accessing Web or FTP services via the public IP address can be automatically redirected to local servers in the LAN (Local Area Network). The DIR-635 firewall feature filters out unrecognized packets to protect your LAN network so all computers networked with the DIR-635 are invisible to the outside world. If you wish, you can make some of the LAN computers accessible from the Internet by enabling Virtual Server. Depending on the requested service, the DIR-635 redirects the external service request to the appropriate server within the LAN network. The DIR-635 is also capable of port-redirection meaning incoming traffic to a particular port may be redirected to a different port on the server computer. Each virtual service that is created will be listed at the bottom of the screen in the Virtual Servers List. There are pre-defined virtual services already in the table. You may use them by enabling them and assigning the server IP to use that particular virtual service. For a list of ports for common applications, please visit http://support.dlink.com/faq/view.asp?prod_id=1191. Virtual Server

Section 3 - Configuration This will allow you to open a single port. If you would like to open a range of ports, refer to page 35. Enter a name for the rule or select an application from the drop-down menu. Select an application and click << to populate the fields. Enter the IP address of the computer on your local network that you want to allow the incoming service to. If your computer is receiving an IP address automatically from the router (DHCP), you computer will be listed in the Computer Name drop-down menu. Select your computer and click <<. Enter the port that you want to open next to Private Port and Public Port. The private and public ports are usually the same. The public port is the port seen from the Internet side, and the private port is the port being used by the application on the computer within your local network. Select TCP, UDP, or Both from the drop-down menu. The schedule when the Virtual Server Rule is enabled. The schedule may be set to Always, which will allow the particular service to always be enabled. You can create your own times in the Tools > Schedules section. Select Allow All (most common) or a created Inbound Filter. You may create your own inbound filters in the Advanced > Inbound Filter page. Name: IP Address: Private Port/ Public Port: Protocol Type: Schedule: Inbound Filter:

Section 3 - Configuration This will allow you to open a single port or a range of ports. Port Forwarding Enter a name for the rule or select an application from the drop-down menu. Select an application and click << to populate the fields. Enter the IP address of the computer on your local network that you want to allow the incoming service to. If your computer is receiving an IP address automatically from the router (DHCP), you computer will be listed in the Computer Name drop-down menu. Select your computer and click <<. Enter the TCP and/or UDP or ports that you want to open. Enter a single port or a range and use a comma to seperate the ports. Example: 24,1009,3000-4000 Schedule when the Virtual Server Rule is enabled. The schedule may be set to Always, which will allow the particular service to always be enabled. You can create your own times in the Tools > Schedules section. Select Allow All (most common) or a created Inbound Filter. You may create your own inbound filters in the Advanced > Inbound Filter page. Name: IP Address: TCP/UDP: Schedule: Inbound Filter:

Section 3 - Configuration Enter a name for the rule. You may select a pre-defined application from the drop-down menu and click <<. Select either a single port or a range of ports. This port triggers the pre-defined application. Select the protocol for the trigger port - TCP, UDP, or Both. This is the port number on the Internet side that will be used to access the application. You may define a single port or a range of ports. You can use a comma to add multiple ports or port ranges. Select the protocol for the firewall port- TCP, UDP, or Both. The schedule when the Application Rule is enabled. The schedule may be set to Always, which will allow the particular service to always be enabled. You can create your own times in the Tools > Schedules section. Name: Trigger: Traffic Type: Firewall: Traffic Type: Schedule: Application Rules Some applications require multiple connections, such as Internet gaming, video conferencing, Internet telephony and others. These applications have difficulties working through NAT (Network Address Translation). Special Applications makes some of these applications work with the DIR-635. If you need to run applications that require multiple connections, specify the port normally associated with an application in the Trigger Port field, select the protocol type as TCP or UDP, then enter the firewall (public) ports associated with the trigger port to open them for inbound traffic. The DIR-635 provides some predefined applications in the table on the bottom of the web page. Select the application you want to use and enable it.

Section 3 - Configuration QoS Engine This option is disabled by default. Enable this option for better performance and experience with, online games and other interactive applications, such as VoIP. This option is enabled by default when the QoS Engine option is enabled. This option will allow your router to automatically determine the uplink speed of your Internet connection. Displays the detected uplink speed. The speed at which data can be transferred from the router to your ISP. This is determined by your ISP. ISP’s often speed as a download/upload pair. For example, 1.5Mbits/284Kbits. Using this example, you would enter 284. Alternatively you can test your uplink speed with a service such as www.dslreports.com. By default, the router automatically determines whether the underlying connection is an xDSL/Frame-relay network or some other connection type (such as cable modem or Ethernet), and it displays the result as Detected xDSL or Frame Relay Network. If you have an unusual network connection in which you are actually connected via xDSL but for which you have configured as either Static or DHCP in the Internet settings, setting this option to xDSL or Other Frame Relay Network ensures that the router will recognize that it needs to shape traffic slightly differently in order to give the best performance. Choosing xDSL or Other Frame Relay Network causes the measured uplink speed to be reported slightly lower than before on such connections, but gives much better results. When Connection Type is set to automatic, the automatically detected connection type is displayed here. Enable Traffic Shaping: Automatic Uplink Speed: Measured Uplink Speed: Manual Uplink Speed: Connection Type: Detected xDSL: The QoS Engine option helps improve your network gaming performance by prioritizing applications. By default the QoS Engine settings are disabled and application priority is not classified automatically.

Section 3 - Configuration This option is disabled by default. Enable this option for better performance and experience with online games and other interactive applications, such as VoIP. This option is enabled by default. This will allow your router to automatically determine the network priority of running programs. This option should be enabled when you have a slow Internet uplink. It helps to reduce the impact that large low priority network packets can have on more urgent ones. Enable QoS Engine: Automatic Classification: Dynamic Fragmentation:

Section 3 - Configuration Network Filters Select Turn MAC Filtering Off, Allow MAC Addresses Listed Below, or Deny MAC Addresses Listed Below from the drop-down menu. Enter the MAC address you would like to filter. To find the MAC address on a computer, please refer to the Networking Basics section in this manual. Select a DHCP client from the drop-down menu and click << to copy that MAC Address. Select to remove the MAC address. Configure MAC Filtering: MAC Address: DHCP Client: Clear: Use MAC (Media Access Control) Filters to allow or deny LAN (Local Area Network) computers by their MAC addresses from accessing the Network. You can either manually add a MAC address or select the MAC address from the list of clients that are currently connected to the Broadband Router.

Section 3 - Configuration Access Control Click Add Policy to start the Access Control Wizard. Add Policy: The Access Control section allows you to control access in and out of your network. Use this feature as Parental Controls to only grant access to approved sites, limit web access based on time or dates, and/or block access from applications like P2P utilities or games. Click Next to continue with the wizard. Access Control Wizard

Section 3 - Configuration Enter a name for the policy and then click Next to continue. Access Control Wizard (continued) Select a schedule (I.E. Always) from the drop-down menu and then click Next to continue. Enter the following information and then click Next to continue. • Address Type - Select IP address, MAC address, or Other Machines. • IP Address - Enter the IP address of the computer you want to apply the rule to. Select the filtering method and then click Next to continue.

Section 3 - Configuration Access Control Wizard (continued) Enter the rule: Enable - Check to enable the rule. Name - Enter a name for your rule. Dest IP Start - Enter the starting IP address. Dest IP End - Enter the ending IP address. Protocol - Select the protocol. Dest Port Start - Enter the starting port number. Dest Port End - Enter the ending port number. To enable web logging, click Enable. Click Save to save the access control rule. Your newly created policy will now show up under Policy Table.

Section 3 - Configuration Add Website Filtering Rule: Website URL/ Domain: Website Filters Select Allow or Deny. Enter the keywords or URLs that you want to allow or block. Click Save Settings. Website Filters are used to allow you to set up a list of allowed Web sites that can be used by multiple users through the network. To use this feature select to Allow or Deny, enter the domain or website and click Save Settings. You must also select Apply Web Filter under the Access Control section (page 40).

Section 3 - Configuration Enter a name for the inbound filter rule. Select Allow or Deny. Check to enable rule. Enter the starting IP address. Enter 0.0.0.0 if you do not want to specify an IP range. Enter the ending IP address. Enter 255.255.255.255 if you do not want to specify and IP range. Click Add to apply your settings. You must click Save Settings at the top to save the settings. This section will list any rules that are created. You may click the Edit icon to change the settings or enable/disable the rule, or click the Delete icon to remove the rule. Name: Action: Enable: Remote IP Start: Remote IP End: Add: Inbound Filter Rules List: The Inbound Filter option is an advanced method of controlling data received from the Internet. With this feature you can configure inbound data filtering rules that control data based on an IP address range. Inbound Filters can be used with Virtual Server, Port Forwarding, or Remote Administration features. Inbound Filters

Section 3 - Configuration SPI (Stateful Packet Inspection, also known as dynamic packet filtering) helps to prevent cyber attacks by tracking more state per session. It validates that the traffic passing through the session conforms to the protocol. Select one of the following for TCP and UDP ports: Endpoint Independent - Any incoming traffic sent to an open port will be forwarded to the application that opened the port. The port will close if idle for 5 minutes. Address Restricted - Incoming traffic must match the IP address of the outgoing connection. Address and Port Restriction - Incoming traffic must match the IP address and port of the outgoing connection. Enable this feature to protect your network from certain kinds of spoofing attacks. If an application has trouble working from behind the router, you can expose one computer to the Internet and run the application on that computer. Note: Placing a computer in the DMZ may expose that computer to a variety of security risks. Use of this option is only recommended as a last resort. Specify the IP address of the computer on the LAN that you want to have unrestricted Internet communication. If this computer obtains it’s IP address automatically using DHCP, be sure to make a static reservation on the Basic > DHCP page so that the IP address of the DMZ machine does not change. Enable SPI: NAT Endpoint Filtering: Anti-Spoof Checking: Enable DMZ Host: DMZ IP Address: Firewall Settings A firewall protects your network from the outside world. The D-Link DIR-635 offers a firewall type functionality.

Section 3 - Configuration VPN Passthrough RTSP H.323 SIP (VoIP) MMS Application Level Gateway (ALG) Configuration Here you can enable or disable ALG’s. Some protocols and applications require special handling of the IP payload to make them work with network address translation (NAT). Each ALG provides special handling for a specific protocol or application. A number of ALGs for common applications are enabled by default. Allows multiple machines on the LAN to connect to their corporate network using PPTP protocol. Allows multiple VPN clients to connect to their corporate network using IPSec. Some VPN clients support traversal of IPSec through NAT. This ALG may interfere with the operation of such VPN clients. If you are having trouble connecting with your corporate network, try turning this ALG off. Please check with the system adminstrator of your corporate network whether your VPN client supports NAT traversal. Allows applications that use Real Time Streaming Protocol to receive streaming media from the internet. QuickTime and Real Player are some of the common applications using this protocol. Allows devices and applications using VoIP (Voice over IP) to communicate across NAT. Some VoIP applications and devices have the ability to discover NAT devices and work around them. This ALG may interfere with the operation of such devices. If you are having trouble making VoIP calls, try turning this ALG off. PPTP: IPSEC (VPN): RTSP: SIP:

Section 3 - Configuration Enter the IP address of packets that will take this route. Enter the netmask of the route, please note that the octets must match your destination IP address. Enter your next hop gateway to be taken if this route is used. The route metric is a value from 1 to 16 that indicates the cost of using this route. A value 1 is the lowest cost and 15 is the highest cost. Select the interface that the IP packet must use to transit out of the router when this route is used. Destination IP: Netmask: Gateway: Metric: Interface: Routing The Routing option is an advanced method of customizing specific routes of data through your network.

Section 3 - Configuration Set the transmit power of the antennas. Beacons are packets sent by an Access Point to synchronize a wireless network. Specify a value. 100 is the default setting and is recommended. This value should remain at its default setting of 2346. If inconsistent data flow is a problem, only a minor modification should be made. The fragmentation threshold, which is specified in bytes, determines whether packets will be fragmented. Packets exceeding the 2346 byte setting will be fragmented before transmission. 2346 is the default setting. (Delivery Traffic Indication Message) 3 is the default setting. A DTIM is a countdown informing clients of the next window for listening to broadcast and multicast messages. WLAN Partition prevents associated wireless clients from communicating with each other. WMM is QoS for your wireless network. This will improve the quality of video and voice applications for your wireless clients. Check this box to reduce the guard interval time therefore increasing the data capacity. However, it’s less reliable and may create higher data loss. Transmit Power: Beacon Period: RTS Threshold: Fragmentation Threshold: DTIM Interval: WLAN Partition: WMM Function: Short GI: Advanced Wireless Settings

Section 3 - Configuration WISH Settings WISH is short for Wireless Intelligent Stream Handling, a technology developed to enhance your experience of using a wireless network by prioritizing the traffic of different applications. Enable this option if you want to allow WISH to prioritize your traffic. Enable WISH: Allows the router to recognize HTTP transfers for many common audio and video streams and prioritize them above other traffic. Such streams are frequently used by digital media players. HTTP: Enables the router to recognize certain audio and video streams generated by a Windows Media Center PC and to prioritize these above other traffic. Such streams are used by systems known as Windows Media Extenders, such as the Xbox 360. Windows Media Center: When enabled, this option causes the router to automatically attempt to prioritize traffic streams that it doesn’t otherwise recognize, based on the behaviour that the streams exhibit. This acts to deprioritize streams that exhibit bulk transfer characteristics, such as file transfers, while leaving interactive traffic, such as gaming or VoIP, running at a normal priority. Automatic: WISH Rules: A WISH Rule identifies a specific message flow and assigns a priority to that flow. For most applications, the priority classifiers ensure the right priorities and specific WISH Rules are not required. WISH supports overlaps between rules. If more than one rule matches for a specific message flow, the rule with the highest priority will be used.

Section 3 - Configuration Create a name for the rule that is meaningful to you. Name: The priority of the message flow is entered here. The four priorities are defined as: BK: Background (least urgent) BE: Best Effort. VI: Video VO: Voice (most urgent) Priority: The protocol used by the messages. Protocol: The rule applies to a flow of messages for which one computer’s IP address falls within the range set here. Host IP Range: The rule applies to a flow of messages for which host’s port number is within the range set here. Host Port Range:

Section 3 - Configuration Enable the Wi-Fi Protected Setup feature. Locking the wireless security settings prevents the settings from being changed by the Wi-Fi Protected Setup feature of the router. Devices can still be added to the network using Wi-Fi Protected Setup. However, the settings of the network will not change once this option is checked. A PIN is a unique number that can be used to add the router to an existing network or to create a new network. The default PIN may be printed on the bottom of the router. For extra security, a new PIN can be generated. You can restore the default PIN at any time. Only the Administrator (“admin” account) can change or reset the PIN. Shows the current value of the router’s PIN. Restore the default PIN of the router. Create a random number that is a valid PIN. This becomes the router’s PIN. You can then copy this PIN to the user interface of the registrar. Enable: Lock Wireless Security Settings: PIN Settings: Current PIN: Reset PIN to Default: Generate New PIN: Wi-Fi Protected Setup Wi-Fi Protected Setup (WPS) System is a simplified method for securing your wireless network during the Initial setup as well as the Add New Device processes. The Wi-Fi Alliance (WFA) has certified the process for different products as well as manufactures. The process is just as easy, as pressing a button for the Push-Button Method or correctly entering the 8-digit code for the Pin-Code Method. The time reduction in setup and ease of use are quite beneficial, while the highest wireless Security setting of WPA2 is automatically used.

Section 3 - Configuration This wizard helps you add wireless devices to the wireless network. The wizard will either display the wireless network settings to guide you through manual configuration, prompt you to enter the PIN for the device, or to press the configuration button on the device. If the device supports Wi-Fi Protected Setup, you can add it to the network by pressing the configuration button on the device and then switch on the router within 60 seconds. The status LED on the router will flash three times if the device has been successfully added to the network. There are several ways to add a wireless device to your network. A registrar controls access to the wireless network. A registrar only allows devices onto the wireless network if you have entered the PIN, or if you have pressed the Wi-Fi Protected Setup button on the device. The router acts as a registrar for the network, although other devices may act as a registrar as well. Start the wizard. Add Wireless Station: Add Wireless Device with WPS:

Section 3 - Configuration UPnP Internet Ping Block Internet Port Speed Multicast Streams To use the Universal Plug and Play (UPnP™) feature click on Enabled. UPNP provides compatibility with networking equipment, software and peripherals. Unchecking the box will not allow the DIR-635 to respond to pings. Blocking the Ping may provide some extra security from hackers. Check the box to allow the Internet port to be pinged. Select from the drop-down menu if you would like to apply the Inbound Filter to the WAN ping. Refer to page 44 for more information regarding Inbound Filter. You may set the port speed of the Internet port to 10Mbps, 100Mbps, or auto. Some older cable or DSL modems may require you to set the port speed to 10Mbps. Check the box to allow multicast traffic to pass through the router from the Internet. Enable UPnP: WAN Ping: WAN Ping Inbound Filter: WAN Port Speed: Multicast streams: Advanced Network Settings

Section 3 - Configuration Enter a new password for the Administrator Login Name. The administrator can make changes to the settings. Enter the new password for the User login. If you login as the User, you can only see the settings, but cannot change them. Enter a name for the DIR-635 router. Remote management allows the DIR-635 to be configured from the Internet by a web browser. A username and password is still required to access the Web-Management interface. In general, only a member of your network can browse the built-in web pages to perform Administrator tasks. This feature enables you to perform Administrator tasks from the remote (Internet) host. The port number used to access the DIR-635. Example: http://x.x.x.x:8080 whereas x.x.x.x is the Internet IP address of the DIR-635 and 8080 is the port used for the Web Management interface. This section will list any rules that are created. You may click the Edit icon to change the settings or enable/disable the rule, or click the Delete icon to remove the rule. Check to enable HTTPS to connect to the router securely. Admin Password: User Password: Gateway Name: Enable Remote Management: Remote Admin Port: Inbound Filter: Enable HTTPS Server: Administrator Settings This page will allow you to change the Administrator and User passwords. You can also enable Remote Management. There are two accounts that can access the management interface through the web browser. The accounts are admin and user. Admin has read/write access while the user has read-only access. User can only view the settings but cannot make any changes. Only the admin account has the ability to change both admin and user account passwords.

Section 3 - Configuration Time Settings Select the Time Zone from the drop-down menu. To select Daylight Saving time manually, select enabled or disabled, and enter a start date and an end date for daylight saving time. NTP is short for Network Time Protocol. NTP synchronizes computer clock times in a network of computers. Check this box to use a NTP server. This will only connect to a server on the Internet, not a local server. Enter the NTP server or select one from the drop-down menu. To manually input the time, enter the values in these fields for the Year, Month, Day, Hour, Minute, and Second and then click Set Time. You can also click Copy Your Computer’s Time Settings. Time Zone: Daylight Saving: Enable NTP Server: NTP Server Used: Manual: The Time Configuration option allows you to configure, update, and maintain the correct time on the internal system clock. From this section you can set the time zone that you are in and set the Time Server. Daylight Saving can also be configured to automatically adjust the time when needed.

Section 3 - Configuration SysLog The Broadband Router keeps a running log of events and activities occurring on the Router. You may send these logs to a SysLog server on your network. Enable Logging to SysLog Server: SysLog Server IP Address: Check this box to send the router logs to a SysLog Server. The address of the SysLog server that will be used to send the logs. You may also select your computer from the drop-down menu (only if receiving an IP address from the router via DHCP).

Section 3 - Configuration When this option is enabled, router activity logs are mailed to a designated email address. This email address will appear as the sender when you receive a log file or firmware upgrade notification via email. Enter the email address where you want the email sent. Enter the SMTP server address for sending email. If your SMTP server requires authentication, select this option. Check this box if your SMTP server requires authentication. Enter your account for sending email. Enter the password associated with the account. Re- type the password associated with the account. When this option is selected, logs will be sent via email when the log is full. Selecting this option will send the logs via email according to schedule. This option is enabled when On Schedule is selected. You can select a schedule from the list of defined schedules. To create a schedule, go to Tools > Schedules. Email Settings The Email feature can be used to send the system log files, router alert messages, and firmware update notification to your email address. Enable Email Notification: From Email Address: To Email Address: SMTP Server Address: Enable Authentication: Account Name: Password: On Log Full: On Schedule: Schedule:

Section 3 - Configuration Use this option to save the current router configuration settings to a file on the hard disk of the computer you are using. Click Save and you will see a file dialog, where you can select a location and file name for the settings. Use this option to load previously saved router configuration settings. First, use the Browse control to find a previously save file of configuration settings. Then, click Load to transfer those settings to the router. This option will restore all configuration settings back to the settings that were in effect at the time the router was shipped from the factory. Any settings that have not been saved will be lost, including any rules that you have created. If you want to save the current router configuration settings, click Save. Select to reboot the router. Save Settings to Local Hard Drive: Load Settings from Local Hard Drive: Restore to Factory Default Settings: Reboot Device: System Settings

Section 3 - Configuration Click Check Online Now for Latest Firmware Version to find out if there is an updated firmware. Download the new firmware to your hard drive. After you have downloaded the new firmware, click Browse to locate the firmware update on your hard drive. Click Upload to complete the firmware upgrade. Check Automatically Check Online for Latest Firmware Version to have the router check automatically to see if there is a new firmware upgrade. Check Email Notification of Newer Firmware Version to have the router send an email when there is a new firmware available. Firmware Upgrade: Browse: Notifications Options: Update Firmware You can upgrade the firmware of your router here. Make sure the firmware you want to use is on the local hard drive of the computer. Click Browse to locate the firmware file for the update. Please check the D-Link support site for firmware updates at http://support.dlink.com. You can download firmware upgrades from the D-Link support site.

Section 3 - Configuration Dynamic Domain Name System is a method of keeping a domain name linked to a changing IP Address. Check the box to enable DDNS. Choose your DDNS provider from the drop down menu. Enter the Host Name that you registered with your DDNS service provider. Enter the Username for your DDNS account. Enter the Password for your DDNS account. Enter the period (in hours). Displays the current connection status. Enable Dynamic DDNS: Server Address: Host Name: Username or Key: Password or Key: Timeout: Status: DDNS The DDNS feature allows you to host a server (Web, FTP, Game Server, etc…) using a domain name that you have purchased (www.whateveryournameis.com) with your dynamically assigned IP address. Most broadband Internet Service Providers assign dynamic (changing) IP addresses. Using a DDNS service provider, your friends can enter in your domain name to connect to your server no matter what your IP address is.

Section 3 - Configuration Enter the IP Address that you wish to png, and click Ping. The results of your ping attempts will be displayed here. System Check Ping Test: Ping Results:

Section 3 - Configuration Enter a name for your new schedule. Select a day, a range of days, or all week to include every day. Check All Day - 24hrs or enter a start and end time for your schedule. Click Save to save your schedule. You must click Save Settings at the top for your schedules to go into effect. The list of schedules will be listed here. Click the Edit icon to make changes or click the Delete icon to remove the schedule. Name: Days: Time: Save: Schedule Rules List: Schedules Schedules can be created for use with enforcing rules. For example, if you want to restrict web access to Mon-Fri from 3pm to 8pm, you could create a schedule selecting Mon, Tue, Wed, Thu, and Fri and enter a Start Time of 3pm and End Time of 8pm.

Section 3 - Configuration This page displays the current information for the DIR-635. It will display the LAN, WAN (Internet), and Wireless information. If your Internet connection is set up for a Dynamic IP address then a release and renew button will be displayed. Use Release to disconnect from your ISP and use Renew to connect to your ISP. If your Internet connection is set up for PPPoE, a Connect and a Disconnect button will be displayed on the screen. Use Disconnect to drop the PPPoE connection and use Connect to establish the PPPoE connection. Displays the router’s time and firmware version. Displays the MAC address and the public IP settings for the router. Displays the MAC address and the private (local) IP settings for the router. Displays the wireless MAC address and your wireless settings such as SSID and Channel. Displays computers and devices that are connected to the router via Ethernet and that are receiving an IP address assigned by the router (DHCP). General: WAN: LAN: Wireless LAN: LAN Computers: Device Information

Section 3 - Configuration Logs What to View: View Levels: Apply Log Settings: Refresh: Clear: Email Now: Save Log: You can select the types of messages that you want to display from the log. Firewall & Security, System, and Router Status messages can be selected. There are three levels of message importance: Informational, Warning, and Critical. Select the levels that you want display in the log. The log results are filtered so that only the selected appear. Updates the log details on the screen so it displays any recent activity. Clears all of the log contents. This option will send a copy of the router log to the email address configured in the Tools > Email screen. This option will save the router to a log file on your computer. The router automatically logs (records) events of possible interest in it’s internal memory. If there isn’t enough internal memory for all events, logs of older events are deleted but logs of the latest events are retained. The Logs option allows you to view the router logs. You can define what types of events you want to view and the level of the events to view. This router also has external Syslog Server support so you can send the log files to a computer on your network that is running a Syslog utility.

Section 3 - Configuration Statistics The screen below displays the Traffic Statistics. Here you can view the amount of packets that pass through the DIR-635 on both the Internet and the LAN ports. The traffic counter will reset if the device is rebooted. Internet Sessions

Section 3 - Configuration The wireless client table displays a list of current connected wireless clients. This table also displays the connection time and MAC address of the connected wireless clients. Wireless The WISH Sessions page displays full details of wireless clients that are connected when WISH is enabled. WISH Sessions

Section 4 - Security Wireless Security This section will show you the different levels of security you can use to protect your data from intruders. The DIR-635 offers the following types of security: • WPA2 (Wi-Fi Protected Access 2) • WPA2-PSK (Pre-Shared Key) • WPA (Wi-Fi Protected Access) • WPA-PSK (Pre-Shared Key) What is WPA? WPA, or Wi-Fi Protected Access, is a Wi-Fi standard that was designed to improve the security features of WEP (Wired Equivalent Privacy). The 2 major improvements over WEP: • Improved data encryption through the Temporal Key Integrity Protocol (TKIP). TKIP scrambles the keys using a hashing algorithm and, by adding an integrity-checking feature, ensures that the keys haven’t been tampered with. WPA2 is based on 802.11i and uses Advanced Encryption Standard (AES) instead of TKIP. • User authentication, which is generally missing in WEP, through the extensible authentication protocol (EAP). WEP regulates access to a wireless network based on a computer’s hardware-specific MAC address, which is relatively simple to be sniffed out and stolen. EAP is built on a more secure public-key encryption system to ensure that only authorized network users can access the network. WPA-PSK/WPA2-PSK uses a passphrase or key to authenticate your wireless connection. The key is an alpha-numeric password between 8 and 63 characters long. The password can include symbols (!?*&_) and spaces. This key must be the exact same key entered on your wireless router or access point. WPA/WPA2 incorporates user authentication through the Extensible Authentication Protocol (EAP). EAP is built on a more secure public key encryption system to ensure that only authorized network users can access the network.

Section 4 - Security Wireless Security Setup Wizard To run the security wizard, click on Setup at the top and then click Launch Wireless Security Setup Wizard. Type your desired wireless network name (SSID). Automatically: Select this option to automatically generate the router’s network key and click Next. Manually: Select this option to manually enter your network key and click Next.

Section 4 - Security If you selected Automatically, the summary window will display your settings. Write down the security key and enter this on your wireless clients. Click Save to save your settings. If you selected Manually, the following screen will appear.

Section 4 - Security From the Setup > Wireless Settings screen, click Add Wireless Device with WPS. Add Wireless Device with WPS Wizard PIN: Select this option to use PIN method. In order to use this method you must know the wireless client’s 8 digit PIN and click Connect. PBC: Select this option to use PBC (Push Button) method to add a wireless client. Click Connect. Select Auto to add a wireless client using WPS (Wi-Fi Protected Setup). Once you select Auto and click Connect, you will have a 120 second time limit to apply the settings to your wireless client(s) and successfully establish a connection. If you select Manual, a settings summary screen will appear. Write down the security key and enter this on your wireless clients.

Section 4 - Security Configure WPA-Personal (PSK) It is recommended to enable encryption on your wireless router before your wireless network adapters. Please establish wireless connectivity before enabling encryption. Your wireless signal may degrade when enabling encryption due to the added overhead. 1. Log into the web-based configuration by opening a web browser and entering the IP address of the router (192.168.0.1). 2. Click Setup and then click Wireless Settings. 3. Security Mode: Select WPA-Personal for this mode option. 4 WPA Mode: Select Auto, WPA2 Only, or WPA Only. Select Auto, if you have wireless clients using both WPA and WPA2. 5. Cypher Type: Select TKIP and AES, TKIP, or AES. 6. Group Key Update Interval: Enter the time interval required for the group key to broadcast and multicast data is changed (3600 is default). 7. Pre-Shared Key: Enter a key (passphrase). The key is entered as a pass- phrase in ASCII format at both ends of the wireless connection. The pass- phrase must be between 8-63 characters. 8. Click Save Settings to save your settings. If you are configuring the router with a wireless adapter, you will lose connectivity until you enable WPA- PSK on your adapter and enter the same passphrase as you did on the router.

Section 4 - Security It is recommended to enable encryption on your wireless router before your wireless network adapters. Please establish wireless connectivity before enabling encryption. Your wireless signal may degrade when enabling encryption due to the added overhead. 1. Log into the web-based configuration by opening a web browser and enter the IP address of the router (192.168.0.1). 2. Click Setup and then click Wireless Settings. 2. Security Mode: Select WPA-Enterprise for this mode option. 3. WPA Mode: Select Auto, WPA2 Only, or WPA Only. Select Auto if you have wireless clients using both WPA and WPA2. 4. Cypher Type: Select TKIP and AES, TKIP, or AES. 5. Group Key Update Interval: Enter the time interval required for the group key to broadcast and multicast data is changed. The default value is 3600. 6. Authentication Timeout: Enter the time interval for a client to re- authenticate. The default value is 60 minutes. 7. RADIUS Server IP Address: Enter the IP Address of your RADIUS server. 8. RADIUS Server Port: Enter the port number of your RADIUS server. 1812 is the default port number. Configure WPA-Enterprise (RADIUS)

Section 4 - Security 9. RADIUS Server Shared Secret: Enter the security key. 10. If the MAC Address Authentication box is selected then the user will need to connect from the same computer whenever logging into the wireless network. 11. Click Advanced to enter settings for a secondary RADIUS Server. 12. Click Apply Settings to save your settings.

Section 5 - Connecting to a Wireless Network Connect to a Wireless Network Using Windows Vista® Windows Vista® users may use the built-in wireless utility. If you are using another company’s utility or Windows® 2000, please refer to the user manual of your wireless adapter for help with connecting to a wireless network. Most utilities will have a “site survey” option similar to the Windows Vista® utility as seen below. Right-click on the wireless computer icon in your system tray (lower-right corner next to the time). Select Connect to a network. If you receive the Wireless Networks Detected dialog box, click on the center of the box to access the utility. or The utility will display any available wireless networks in your area. Click on a network (displayed using the SSID) and click Connect. If you get a good signal but cannot access the Internet, check you TCP/IP settings for your wireless adapter. Refer to the Networking Basics section in this manual for more information.

Section 5 - Connecting to a Wireless Network Configure Wireless Security It is recommended to enable wireless security (WPA/WPA2) on your wireless router or access point before configuring your wireless adapter. If you are joining an existing network, you will need to know the security key or passphrase being used. 2. Highlight the wireless network (SSID) you would like to connect to and click Connect. 1. Open the Windows Vista® Wireless Utility by right-clicking on the wireless computer icon in your system tray (lower right corner of screen). Select Connect to a network.

Section 5 - Connecting to a Wireless Network 3. Enter the same security key or passphrase that is on your router and click Connect. It may take 20-30 seconds to connect to the wireless network. If the connection fails, please verify that the security settings are correct. The key or passphrase must be exactly the same as on the wireless router.

Section 5 - Connecting to a Wireless Network Connect Using WCN 2.0 in Windows Vista® The router supports Wi-Fi protection, referred to as WCN 2.0 in Windows Vista®. The following instructions for setting this up depends on whether you are using Windows Vista® to configure the router or third party software. When you first set up the router, Wi-Fi protection is disabled and not configured. To enjoy the benefits of Wi-Fi protection, the router must be both enabled and configured. There are three basic methods to accomplish this: use Windows Vista’s built-in support for WCN 2.0, use software provided by a third party, or manually configure. If you are running Windows Vista®, log into the router and click the Enable checkbox in the Basic > Wireless section. Use the Current PIN that is displayed on the Advanced > Wi-Fi Protected Setup section or choose to click Generate New PIN or Reset PIN to Default. For additional information, please refer to page 68. If you are using third party software to set up Wi-Fi Protection, carefully follow the directions. When you are finished, proceed to the next section to set up the newly-configured router.

Section 6 - Troubleshooting Connect to a Wireless Network Using Windows® XP Windows® XP users may use the built-in wireless utility (Zero Configuration Utility). The following instructions are for Service Pack 2 users. If you are using another company’s utility or Windows® 2000, please refer to the user manual of your wireless adapter for help with connecting to a wireless network. Most utilities will have a “site survey” option similar to the Windows® XP utility as seen below. Right-click on the wireless computer icon in your system tray (lower-right corner next to the time). Select View Available Wireless Networks. If you receive the Wireless Networks Detected bubble, click on the center of the bubble to access the utility. or The utility will display any available wireless networks in your area. Click on a network (displayed using the SSID) and click Connect. If you get a good signal but cannot access the Internet, check you TCP/IP settings for your wireless adapter. Refer to the Networking Basics section in this manual for more information.

Section 6 - Troubleshooting Configure WPA-PSK It is recommended that you enable WPA-PSK on your wireless router or access point before configuring your wireless adapter. If you are joining an existing network, you will need to know the WPA-PSK key being used. 2. Highlight the wireless network (SSID) you would like to connect to and click Connect. 1. Open the Windows® XP Wireless Utility by right-clicking on the wireless computer icon in your system tray (lower-right corner of screen). Select View Available Wireless Networks.

Section 6 - Troubleshooting 3. The Wireless Network Connection box will appear. Enter the WPA-PSK passphrase and click Connect. It may take 20-30 seconds to connect to the wireless network. If the connection fails, please verify that the WPA-PSK settings are correct. The WPA-PSK passphrase must be exactly the same as on the wireless router.

Section 6 - Troubleshooting Troubleshooting This chapter provides solutions to problems that can occur during the installation and operation of the DIR-635. Read the following descriptions if you are having problems. (The examples below are illustrated in Windows® XP. If you have a different operating system, the screenshots on your computer will look similar to the following examples.) 1. Why can’t I access the web-based configuration utility? When entering the IP address of the D-Link router (192.168.0.1 for example), you are not connecting to a website on the Internet or have to be connected to the Internet. The device has the utility built-in to a ROM chip in the device itself. Your computer must be on the same IP subnet to connect to the web-based utility. • Make sure you have an updated Java-enabled web browser. We recommend the following: • Internet Explorer 6.0 or higher • Netscape 8 or higher • Mozilla 1.7.12 (5.0) or higher • Opera 8.5 or higher • Safari 1.2 or higher (with Java 1.3.1 or higher) • Camino 0.8.4 or higher • Firefox 1.5 or higher • Verify physical connectivity by checking for solid link lights on the device. If you do not get a solid link light, try using a different cable or connect to a different port on the device if possible. If the computer is turned off, the link light may not be on. • Disable any internet security software running on the computer. Software firewalls such as Zone Alarm, Black Ice, Sygate, Norton Personal Firewall, and Windows® XP firewall may block access to the configuration pages. Check the help files included with your firewall software for more information on disabling or configuring it.

Section 6 - Troubleshooting • Configure your Internet settings: • Go to Start > Settings > Control Panel. Double-click the Internet Options Icon. From the Security tab, click the button to restore the settings to their defaults. • Click the Connection tab and set the dial-up option to Never Dial a Connection. Click LAN Settings. Make sure nothing is checked. Click OK. • Go to the Advanced tab and click the button to restore these settings to their defaults. Click OK three times. • Close your web browser (if open) and then re-open it again. • Access the web management. Open your web browser and enter the IP address of your D-Link router in the address bar. This should open the login page for your the web management. • If you still cannot access the configuration, unplug the power to the router for 10 seconds and plug back in. Wait about 30 seconds and try accessing the configuration. If you have multiple computers, try connecting using a different computer. 2. What can I do if I forgot my password? If you forgot your password, you must reset your router. Unfortunately this process will change all your settings back to the factory defaults. To reset the router, locate the reset button (hole) on the rear panel of the unit. With the router powered on, use a paperclip to hold the button down for 10 seconds. Release the button and the router will go through its reboot process. Wait about 30 seconds to access the router. The default IP address is 192.168.0.1. When logging in, the username is admin and leave the password box empty.

Section 6 - Troubleshooting 3. Why can’t I connect to certain sites or send and receive emails when connecting through my router? If you are having a problem sending or receiving email, or connecting to secure sites such as eBay, banking sites, and Hotmail, we suggest lowering the MTU in increments of ten (Ex. 1492, 1482, 1472, etc). Note: AOL DSL+ users must use MTU of 1400. To find the proper MTU Size, you’ll have to do a special ping of the destination you’re trying to go to. A destination could be another computer, or a URL. • Go to Start and then click Run. • Windows® 95, 98, and Me users type in command (Windows® NT, 2000, and XP users type in cmd) and press Enter (or click OK). • Once the window opens, you’ll need to do a special ping. Use the following syntax: ping [url] [-f] [-l] [MTU value] Example: ping yahoo.com -f -l 1472

Section 6 - Troubleshooting You should start at 1472 and work your way down by 10 each time. Once you get a reply, go up by 2 until you get a fragmented packet. Take that value and add 28 to the value to account for the various TCP/IP headers. For example, lets say that 1452 was the proper value, the actual MTU size would be 1480, which is the optimum for the network we’re working with (1452+28=1480). Once you find your MTU, you can now configure your router with the proper MTU size. To change the MTU rate on your router follow the steps below: • Open your browser, enter the IP address of your router (192.168.0.1) and click OK. • Enter your username (admin) and password (blank by default). Click OK to enter the web configuration page for the device. • Click Setup and then click Manual Configure. • To change the MTU enter the number in the MTU field and click Save Settings to save your settings. • Test your email. If changing the MTU does not resolve the problem, continue changing the MTU in increments of ten.

Appendix A - Wireless Basics D-Link wireless products are based on industry standards to provide easy-to-use and compatible high-speed wireless connectivity within your home, business or public access wireless networks. Strictly adhering to the IEEE standard, the D-Link wireless family of products will allow you to securely access the data you want, when and where you want it. You will be able to enjoy the freedom that wireless networking delivers. A wireless local area network (WLAN) is a cellular computer network that transmits and receives data with radio signals instead of wires. Wireless LANs are used increasingly in both home and office environments, and public areas such as airports, coffee shops and universities. Innovative ways to utilize WLAN technology are helping people to work and communicate more efficiently. Increased mobility and the absence of cabling and other fixed infrastructure have proven to be beneficial for many users. Wireless users can use the same applications they use on a wired network. Wireless adapter cards used on laptop and desktop systems support the same protocols as Ethernet adapter cards. Under many circumstances, it may be desirable for mobile network devices to link to a conventional Ethernet LAN in order to use servers, printers or an Internet connection supplied through the wired LAN. A Wireless Router is a device used to provide this link. Wireless Basics

Appendix A - Wireless Basics What is Wireless? Wireless or Wi-Fi technology is another way of connecting your computer to the network without using wires. Wi-Fi uses radio frequency to connect wirelessly, so you have the freedom to connect computers anywhere in your home or office network. Why D-Link Wireless? D-Link is the worldwide leader and award winning designer, developer, and manufacturer of networking products. D-Link delivers the performance you need at a price you can afford. D-Link has all the products you need to build your network. How does wireless work? Wireless works similar to how cordless phone work, through radio signals to transmit data from one point A to point B. But wireless technology has restrictions as to how you can access the network. You must be within the wireless network range area to be able to connect your computer. There are two different types of wireless networks Wireless Local Area Network (WLAN), and Wireless Personal Area Network (WPAN). Wireless Local Area Network (WLAN) In a wireless local area network, a device called an Access Point (AP) connects computers to the network. The access point has a small antenna attached to it, which allows it to transmit data back and forth over radio signals. With an indoor access point as seen in the picture, the signal can travel up to 300 feet. With an outdoor access point the signal can reach out up to 30 miles to serve places like manufacturing plants, industrial locations, college and high school campuses, airports, golf courses, and many other outdoor venues.

Appendix A - Wireless Basics Wireless Personal Area Network (WPAN) Bluetooth is the industry standard wireless technology used for WPAN. Bluetooth devices in WPAN operate in a range up to 30 feet away. Compared to WLAN the speed and wireless operation range are both less than WLAN, but in return it doesn’t use nearly as much power which makes it ideal for personal devices, such as mobile phones, PDAs, headphones, laptops, speakers, and other devices that operate on batteries. Who uses wireless? Wireless technology as become so popular in recent years that almost everyone is using it, whether it’s for home, office, business, D-Link has a wireless solution for it. Home • Gives everyone at home broadband access • Surf the web, check email, instant message, and etc • Gets rid of the cables around the house • Simple and easy to use Small Office and Home Office • Stay on top of everything at home as you would at office • Remotely access your office network from home • Share Internet connection and printer with multiple computers • No need to dedicate office space

Appendix A - Wireless Basics Where is wireless used? Wireless technology is expanding everywhere not just at home or office. People like the freedom of mobility and it’s becoming so popular that more and more public facilities now provide wireless access to attract people. The wireless connection in public places is usually called “hotspots”. Using a D-Link Cardbus Adapter with your laptop, you can access the hotspot to connect to Internet from remote locations like: Airports, Hotels, Coffee Shops, Libraries, Restaurants, and Convention Centers. Wireless network is easy to setup, but if you’re installing it for the first time it could be quite a task not knowing where to start. That’s why we’ve put together a few setup steps and tips to help you through the process of setting up a wireless network. Tips Here are a few things to keep in mind, when you install a wireless network. Centralize your router or Access Point Make sure you place the router/access point in a centralized location within your network for the best performance. Try to place the router/access point as high as possible in the room, so the signal gets dispersed throughout your home. If you have a two-story home, you may need a repeater to boost the signal to extend the range. Eliminate Interference Place home appliances such as cordless telephones, microwaves, and televisions as far away as possible from the router/access point. This would significantly reduce any interference that the appliances might cause since they operate on same frequency.

Appendix A - Wireless Basics Security Do not allow your neighbors or intruders connect to your wireless network. Secure your wireless network by turning on the WPA or WEP security feature on the router. Refer to the Product Manual for further information. There are basically two modes of networking: • Infrastructure – All wireless clients will connect to an access point or wireless router. • Ad-Hoc – Directly connecting to another computer, for peer-to-peer communication, using wireless network adapters on each computer, such as two or more wireless network Cardbus adapters. An Infrastructure network contains an Access Point or wireless router. All the wireless devices, or clients, will connect to the wireless router or access point. An Ad-Hoc network contains only clients, such as laptops with wireless cardbus adapters. All the adapters must be in Ad-Hoc mode to communicate. Wireless Modes

Appendix B - Networking Basics Networking Basics Check your IP address After you install your new D-Link adapter, by default, the TCP/IP settings should be set to obtain an IP address from a DHCP server (i.e. wireless router) automatically. To verify your IP address, please follow the steps below. Go to Start > Run. In the run box type cmd and then click OK. (Windows® Vista users type cmd in the Start Search box.) At the command prompt, type ipconfig and press Enter. This will display the IP address, subnet mask, and the default gateway of your adapter. If the address is 0.0.0.0, check your adapter installation, security settings, and the settings on your router. Some firewall software programs may block a DHCP request on newly installed adapters.

Appendix B - Networking Basics Statically Assign an IP address If you are not using a DHCP capable gateway/router, and you want to assign a static IP address, please follow the steps below: Step 1 Windows® Vista - Go to Start > Control Panel > Network and Internet > Network and Sharing Center > Manage Network Connections Windows® XP - Go to Start > Control Panel > Network Connections Windows® 2000 - From the desktop, right-click My Network Places > Properties Step 2 Right-click on the Local Area Connection which represents your network adapter and select Properties. Step 3 Highlight Internet Protocol (TCP/IP) and click Properties. Step 4 Click Use the following IP address and enter an IP address that is on the same subnet as your network or the LAN IP address on your router. Example: If the router´s LAN IP address is 192.168.0.1, make sure your IP address is 192.168.0.X, where X is a number between 2 and 99. Also, ensure that the number you choose is not in use on the network. The Default Gateway should be set similar to the LAN IP address of your router (192.168.0.1). The Primary DNS should be the same as the LAN IP address of your router (192.168.0.1). The Secondary DNS is not needed or you may enter a DNS server from your ISP. Step 5 Click OK twice to save your settings.

Technical Specifications Standards • IEEE 802.11n (draft 2.0) • IEEE 802.11g • IEEE 802.11b • IEEE 802.3 • IEEE 802.3u Security • WPA-Personal • WPA2-Personal • WPA-Enterprise • WPA2-Enterprise • 64/128-bit WEP Wireless Signal Rates* • 54Mbps • 48Mbps • 36Mbps • 24Mbps • 18Mbps • 12Mbps • 11Mbps • 9Mbps • 6Mbps • 5.5Mbps • 2Mbps • 1Mbps MSC (0-15) • 130Mbps (270) • 117Mbps (243) • 104Mbps (216) • 78Mbps (162) • 66Mbps (135) • 58.5Mbps (121.5) • 52Mbps (108) • 39Mbps (81) • 26Mbps (54) • 19.5Mbps (40.5) • 12Mbps (27) • 6.5Mbps (13.5) Frequency Range 2.4GHz to 2.483GHz External Antenna Type Three detachable reverse SMA Antennas Power Input • 5 VDC, 2.5A • Through external power adapter LEDs • Power • Status • WAN • WLAN • USB • LAN (10/100) (per port) Dimensions 116.84 x 193.04 x 30.48 mm (4.6 x 7.6 x 1.2 inches) Weight 368.3 grams (0.8 lb) Operating Temperature 0°C to 40°C (32°F to 104°F) * Maximum wireless signal rate derived from IEEE Standard 802.11g and Draft 802.11n specifications. Actual data throughput will vary. Network conditions and environmental factors, including volume of network traffic, building materials and construction, and network overhead, lower actual data throughput rate. Environmental factors will adversely affect wireless signal range. Humidity 95% maximum (non-condensing) Certifications • FCC Class B • CE • C-Tick • IC • Wi-Fi • Wi-Fi Protected Setup (WPS) • Works with Windows Vista