Danfoss ECL Comfort 110 Datasheet

230 V a.c. and 24 V a.c. DH-SMT/DK VD.KT.C3.02 © Danfoss 09/2008 1 Description and application The controller is designed for easy installation: one cable, one connector. The ECL Comfort 110 controller has a custom- designed display with backlight. For a quick overview, the display readouts are based on graphic symbols as well as text. The controller has triac outputs for motorized control valve and relay outputs for pump control. It is possible to connect up to 4 temperature sensors (Pt 1000 types) and it has 1 input for override. Room panel or remote control (ECA 60 / 61) can be connected. The ECL Comfort 110 controller can be used as master or slave in controller systems. It is prepared for mounting on a DIN rail, a wall or in a panel. The ECL Comfort 110 is a universal 1-circuit controller for use in district heating substations and district heating systems as well as boiler- based systems. The product is an electronic controller for • weather compensated flow temperature control (heating) • constant temperature control (domestic hot water e.g.) and prepared for new applications by means of chip card and communication interface. Ordering Controllers Type Designation Code no. ECL Comfort 110 Universal hardware - 230 V a.c. 087B1261 ECL Comfort 110 Universal hardware - 24 V a.c. 087B1251 ECL Comfort 110 with timer program Universal hardware - 230 V a.c. 087B1262 ECL Comfort 110 with timer program Universal hardware - 24 V a.c. 087B1252 Panel mounting kit For ECL Comfort 110 087B1249 Instructions, appl. 116 User guide and quick guide (English) 087B8151 Instructions, appl. 130 User guide and quick guide (English) 087B8152 Pt 1000 temperature sensors Type Designation Code No. ESMT Outdoor temperature sensor 084N1012 ESM-10 Room temperature sensor 087B1164 ESM-11 Surface sensor 087B1165 ESMB-12 Universal sensor 087B1184 ESMC Surface sensor incl. 2 m cable 087N0011 ESMU-100 Immersion sensor, 100 mm, copper 087B1180 ESMU-250 Immersion sensor, 250 mm, copper 087B1181 ESMU-100 Immersion sensor, 100 mm, stainless steel 087B1182 ESMU-250 Immersion sensor, 250 mm, stainless steel 087B1183

2 Ordering, continued Accessories Type Designation Code no. ECA 60 Room panel with sensor 087B1140 ECA 61 Remote control with 1 zone clock and sensor 087B1141 ECA 110* Timer program for ECL Comfort 110 (chip card) 087B1248 * The ECA 110 is a supplement to the ECL Comfort 110 versions without a timer program, e.g., the code nos. 087B1261 and 087B1251 (see page 1). With the ECA 110 it will be possible to set personal schedules in terms of start and stop times of the system and thereby optimize the energy supply. Domestic hot water (DHW) (Application 116) Application 116 example Constant DHW temperature control with heat exchanger Basic principles Constant DHW temperature control with heat exchanger or storage tank Typically, the flow temperature is adjusted according to the desired flow temperature. • Adjustment of DHW temperature If the measured DHW temperature is lower than the desired temperature, the motorized control valve is opened gradually and vice versa. • Return temperature limitation The return temperature to the district heating supply should not be too high. If so, the desired flow temperature can be adjusted (typically to a lower value) thus resulting in a gradual closing of the motorized control valve. In boiler-based heating supply the return temperature should not be too low (same adjustment procedure as above). • Circulation pump control The circulation pump is ON when the desired DHW temperature is higher than a user- defined value (factory setting: 20 °C). ECL Comfort 110

3 ECL Comfort 110 Key functions Flow temperature control • Return temperature limitation The controller automatically changes the desired flow temperature to obtain an acceptable return temperature when the return temperature falls below or gets higher than the set value. The return temperature influence can be limited by the min. / max. flow limitation. Optimization • Auto tuning A function for automatically setting the proportional band (Xp) and integration time constant (Tn). Safety functions • Frost protection The controller automatically switches the circulation pump ON when the flow temperature is lower than a user-defined value (factory setting: 10 °C). • Motor protection The controller prevents unstable temperature control thus resulting in a longer life of the actuator. • Pump exercise Exercise of the pump to avoid blocking in periods without heat demand. Heating (Application 130) Application 130 examples District heating circuit with heat exchanger Boiler-based heating circuit

Data sheet DH-SMT/DK VD.KT.C3.02 © Danfoss 09/2008 4 Basic principles Control of district heating circuits with or without heat exchanger and for boiler-based heating circuits Typically, the flow temperature is adjusted according to the desired flow temperature. • Adjustment of flow temperature The desired flow temperature is calculated in the ECL Comfort controller, based on the outdoor temperature. The lower the outdoor temperature, the higher the desired flow temperature. The motorized control valve is opened gradually when the flow temperature is lower than the desired flow temperature and vice versa. • Return temperature limitation The return temperature to the district heating supply should not be too high. If so, the desired flow temperature can be adjusted (typically to a lower value) thus resulting in a gradual closing of the motorized control valve. In boiler-based heating supply the return temperature should not be too low (same adjustment procedure as above). • Room temperature limitation If the measured room temperature does not equal the desired room temperature, the desired flow temperature can be adjusted. • Circulation pump control The circulation pump is ON when the desired flow temperature is higher than a user-defined value (factory setting: 20 °C ) or the outdoor temperature is lower than a user-defined value (factory setting: 2 °C).

5 ECL Comfort 110 General data Ambient temperature 0 - 55 °C Storage temperature -40 - + 70 °C Enclosure DIN rail, wall or panel Sensor type Pt 1000 (1000 Ω @ 0 °C) Grade of enclosure IP 41 DIN 40050 - marking in accordance with the standards EMC-Directive: 2004/108/EC Immunity: 61000-6-1 Emission: 61000-6-3 LVD-Directive: 2006/95/EC Wiring - 230 V a.c. * Connections for safety thermostat Supply voltage 230 V a.c. - 50 Hz Voltage range 207 to 244 V a.c. (IEC 60038) Power consumption 3 VA Load on relay 1 outputs 4 (2) A - 230 V a.c. Load on triac outputs 15 VA @ 230 V a.c. Wiring - 24 V a.c. * Connections for safety thermostat Supply voltage 24 V a.c. - 50 Hz Voltage range 21.6 to 26.4 V a.c. (IEC 60038) Power consumption 3 VA Load on relay 2 outputs 4 (2) A - 230 V a.c. Load on triac outputs 15 VA @ 24 V a.c.