CipherLab 1660 Operation & User’s Manual

All rights reserved The software contains proprietary information of CIPHERLAB CO., LTD.; it is provided under a license agreement containing restrictions on use and disclosure and is also protected by copyright law. Reverse engineering of the software is prohibited. Due to continued product development this information may change without notice. The information and intellectual property contained herein is confidential between CIPHERLAB and the client and remains the exclusive property of CIPHERLAB CO., LTD. If you find any problems in the documentation, please report them to us in writing. CIPHERLAB does not warrant that this document is error-free. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording or otherwise without the prior written permission of CIPHERLAB CO., LTD. For product consultancy and technical support, please contact your local sales representative. Also, you may visit our web site for more information. The CipherLab logo is a registered trademark of CIPHERLAB CO., LTD. All brand, product and service, and trademark names are the property of their registered owners. The editorial use of these names is for identification as well as to the benefit of the owners, with no intention of infringement. CIPHERLAB CO., LTD. Website: http://www.cipherlab.com

device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:  Reorient or relocate the receiving antenna.  Increase the separation between the equipment and receiver.  Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.  Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FOR CANADA This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus as set out in the interference-causing equipment standard entitled "Digital Apparatus," ICES-003 of Industry Canada. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Cet appareil numerique respecte les limites de bruits radioelectriques applicables aux appareils numeriques de Classe B prescrites dans la norme sur le material brouilleur: "Appareils Numeriques," NMB-003 edictee par l'Industrie. IMPORTANT NOTICES

The 1660/1661 unit (FCC ID: Q3N-1660, Q3N-1661) complies with FCC radiation exposure limits set forth for uncontrolled environment and meets the FCC radio frequency (RF) Exposure Guidelines in Supplement C to OET65. The unit has very low level of RF energy that it is deemed to comply without testing of specific absorption ratio (SAR). The 3610 unit (FCC ID: Q3N-3610) complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator & your body. It only operated in hand-held used. If you only transfer data to the host wirelessly, please keep the minimum distance 20 cm between machine & your body. SAFETY PRECAUTIONS RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS.  DO NOT disassemble, incinerate or short circuit the battery.  DO NOT expose the scanner or the battery to any flammable sources.  For green-environment issue, it's important that batteries should be recycled in a proper way.  Under no circumstances, internal components are self-serviceable. CARE & MAINTENANCE  Use a clean cloth to wipe dust off the scanning window and the body of the scanner. DO NOT use/mix any bleach or cleaner.  If you want to put away the scanner for a period of time, download the collected data to a host computer when in the memory mode, and then take out the battery. Store the scanner and battery separately.  When the scanner resumes its work, make sure the battery is fully charged before use.  Keep the scanner away from any magnets and magnetic fields to prevent the laser engine from malfunctioning.  If you shall find the scanner malfunctioning, write down the specific scenario and consult your local sales representative.

 Modified: 1.2.3 – “Record Count of Memory” setting barcodes added  Modified: Wording referring to “CD-ROM” removed 1.31 May 09, 2014  Modified: Care & Maintenance – “Keep the scanner away from any magnets and magnetic fields to prevent the laser engine from malfunctioning.” added  Modified: 1.1.1 – Enable/Disable the [Delete] key barcodes added  Modified: 1.1.3 – Power Level (1661)  Modified: 1.2.1 – Free Memory  New: 1.14.3 – Hardware Reset  New: 2.1.8 – BT HID Transmit Speed  New: 2.1.9 – BT HID Slave/Master Switching  New: 2.1.10 – BT HID Auto-Reconnection (1661 only)  New: 2.5.2 – Activate USB Virtual COM_CDC (100031)  New: 4.8.3 – Conversion Format  New: 4.10.3 – GS1 Formatting, Application ID Mark  New: 4.11.1 – ISBT Concatenation  New: 4.16.5 – Field Separator (GS Character)  New: 4.16.6 – GS1 Formatting, Application ID Mark  Modified: Appendix I – Note for upgrading 3610 firmware added  Modified: Appendix II – ShowScanner, SelectScannerN added  Modified: Appendix III – remove “Send” from “CR*/Send/ENTER*” 1.30 Dec. 25, 2012  Modified: 2.5.1/2.7/3.1 Required USB Virtual COM Driver version 5.4  Modified: 2.1.1/2.4.1/2.6.1 HID Keyboard Type ─ add #78 (Swiss German)/ #79 (Danish) 1.20 Apr. 09, 2012  New: Add 1.1.3 Power Level information  New: Add 1.2.1 Free Memory information  New: Add 4.1.1 Security Level 1.19 Feb. 20, 2012  New: Add Upgrading USB Bridge Firmware 1.18 Nov. 28, 2011  Modified: 4.10 Change GS1-128 default value to Enable  New: Add New Serial Command “#@RDSN” 1.17 Jun. 28, 2011  Modified: 2.1.1 Activate BT HID & Select Keyboard Type — add #77 PCAT (Hungarian)  Modified: 2.4.1 Activate USB HID & Select Keyboard Type — add #77 PCAT (Hungarian)  Modified: 2.6.1 Activate USB HID & Select Keyboard Type — add #77 PCAT (Hungarian) RELEASE NOTES